Ni-based alloy coating on 21-4-N heat-resistant steel was prepared using CO2 laser, and the high-temperature abrasion wear was tested. The microstructure of this cladding layer and its abrasion wear behavior at high t...Ni-based alloy coating on 21-4-N heat-resistant steel was prepared using CO2 laser, and the high-temperature abrasion wear was tested. The microstructure of this cladding layer and its abrasion wear behavior at high temperature by changing compositions and temperatures were investigated by means of optical microscope and scanning electron microscope. Among the three compositions of cladding layer, i.e. Ni21+20%WC+0.5%CeO2, Ni25+20%WC+0.5%CeO2 and Ni60+20%WC+0.5%CeO2, the experimental results show that Ni21+20%WC+ 0.5%CeO2 cladding layer is made up of finer grains, and presents the best abrasion wear behavior at high temperature. The wear pattern of laser cladding layer is mainly grain abrasion at lower temperature, and it would be changed to adhesive abrasion and oxide abrasion at higher temperature.展开更多
1.IntroductionBoronizing can evidently increase thesurface hardness and wear resistance of me-tallic materials[1].It is simple in technique,not expensive and widely used on tools,diesand some other parts which are eas...1.IntroductionBoronizing can evidently increase thesurface hardness and wear resistance of me-tallic materials[1].It is simple in technique,not expensive and widely used on tools,diesand some other parts which are easy towear.However the wear mechanism andbehaviour of boronized layer are not clearwhen abraded by mixed abradants such ascoal,hard mineral etc.[2,3].Several metallic materials commonly展开更多
Mar and abrasion resistance were investigated by a progressive load scratch test and steel wool abrasion test, respectively. Two acrylic coating systems including trimethylolpropane triacrylate (TMPTA) and pentaerythr...Mar and abrasion resistance were investigated by a progressive load scratch test and steel wool abrasion test, respectively. Two acrylic coating systems including trimethylolpropane triacrylate (TMPTA) and pentaerythritol triacrylate (PETA) were prepared. A soft base layer was introduced as an intermediate layer between two different types of top layer and poly (methyl methacrylate) (PMMA) substrate to demonstrate the effect of soft base layer on mar and abrasion resistance. Abrasion damage on the coating surface was found to be less severe, when the soft base layer was incorporated into the coating systems. The reduction in scratch coefficient of friction (SCOF) and surface roughness was also observed. The results suggested that mar and abrasion resistance was greatly influenced by the presence of soft base layer, although different top layers were used. Moreover, it was found that abrasion resistance was further improved as the thicker soft base layer was applied.展开更多
A new technique was introduced that TiN permeation layer composed of diffusion and deposition layer was synthesized on the surface of Q235 steel using plasma point discharge and hollow cathode effect, and then TiB2 fi...A new technique was introduced that TiN permeation layer composed of diffusion and deposition layer was synthesized on the surface of Q235 steel using plasma point discharge and hollow cathode effect, and then TiB2 film was deposited (PVD) on newly-formed surface to create TiN/TiB2 multi-permeation layer. The thickness of this multi-permeation layer is above 10μm and the composition and hardness have graded distribution. It has metallurgical bonding with substrate and the bonding strength is high without any spallation phenomenon. In addition comparative research, between TiN/TiB2 multi-permeation layer and TiB2 film which is directly deposited (PVD) on Q235 steel substrate, on surface appearance, microhardness and friction-abrasion property was carried out. The results show that both of surface consist of uniform, compact and fine cellular structure. Surface microhardness of TiN/TiB2 multi-permeation layer is higher, reaching HV2600; but its average friction coefficient is lower, abrasion crack is shallower and wear resistance is better.展开更多
Monte Carlo simulations reveal considerable straggling of energy loss by the same ions with the same energy in fully-depleted silicon-on-insulator (FDSOI) devices with ultra-thin sensitive silicon layers down to 2.5...Monte Carlo simulations reveal considerable straggling of energy loss by the same ions with the same energy in fully-depleted silicon-on-insulator (FDSOI) devices with ultra-thin sensitive silicon layers down to 2.5 rim. The absolute straggling of deposited energy decreases with decreasing thickness of the active silicon layer. While the relative straggling increases gradually with decreasing thickness of silicon films and exhibits a sharp rise as the thickness of the silicon film descends below a threshold value of 50 nm, with the dispersion of deposited energy ascending above ~10%. Ion species and energy dependence of the energy-loss straggling are also investigated. For a given beam, the dispersion of deposited energy results in large uncertainty on the actual linear energy transfer (LET) of incident ions, and thus single event effect (SEE) responses, which pose great challenges for traditional error rate prediction methods.展开更多
The formula of the thickness of the heat-insulating layer is deduced via heat transfer analysis,according to the principle of heat transfer in limited space.Polishing experiments are carried out using the same technol...The formula of the thickness of the heat-insulating layer is deduced via heat transfer analysis,according to the principle of heat transfer in limited space.Polishing experiments are carried out using the same technological parameters.Compared with the polishing experimental results,the heat transfer model is proved to be correct.As validated by the experimental results,polyurethane heat-insulating layer can effectively improve the service life of the ice fixed abrasive pad and alleviate the melting rate in the polishing process to improve the polishing quality proposed.The heat transfer model provides theoretical basis for research of temperature field of ice fixed abrasive polishing.展开更多
The abrasive waterjet (AWJ) is now widely used in the advanced cutting processes of polymers,metals,glass,ceramics and composite materials like thin multiple-layered material (TMM).Various research and development eff...The abrasive waterjet (AWJ) is now widely used in the advanced cutting processes of polymers,metals,glass,ceramics and composite materials like thin multiple-layered material (TMM).Various research and development efforts have recently been made to understand the science of AWJ.However,the interaction mechanism between a workpiece and high-velocity abrasive particles still remains a complicated problem.In this work,the material removal mechanisms of AWJ such as micro penetration and micro dent were experimentally investigated.In addition,a new computer simulation model considering high strain rate effect was proposed to understand the micro impact behavior of high-velocity micro-sized abrasives in AWJ cutting.展开更多
We theoretically investigate the optical properties of an ultra-thin InN layer embedded in InGaN matrix for light emitters. The peak emission wavelength extends from ultraviolet (374 nm) to green (536 nm) with InN...We theoretically investigate the optical properties of an ultra-thin InN layer embedded in InGaN matrix for light emitters. The peak emission wavelength extends from ultraviolet (374 nm) to green (536 nm) with InN quantum well thickness increasing from 1 monolayer to 2 monolayers, while the overlap of electron–hole wave function remains at a high level (larger than 90%). Increase of In content in InGaN matrix provides a better approach to longer wavelength emission, which only reduces the spontaneous emission rate slightly compared with the case of increasing In content of the conventional InGaN quantum well. Also, the transparency carrier density derived from gain spectrum is of the same order as that in the conventional blue laser diode. Our study provides skillful design on the development of novel structure InN-based light emitting diodes as well as laser diodes.展开更多
The properties of top-contact organic thin-film transistors (TC-OTFTs) using ultra-thin 2, 9-dimethyl-4, 7- diphenyl-1, 10-phenanthroline (BCP) as a hole-blocking interlayer have been improved significantly and a ...The properties of top-contact organic thin-film transistors (TC-OTFTs) using ultra-thin 2, 9-dimethyl-4, 7- diphenyl-1, 10-phenanthroline (BCP) as a hole-blocking interlayer have been improved significantly and a BCP interlayer was inserted into the middle of the pentacene active layer. This paper obtains a fire-new transport mode of an OTFT device with double-conductible channels. The accumulation and transfer of the hole carriers arc limited by the BCP interlayer in the vertical region of the channel. A huge amount of carriers is located not only at the interface between pentacene and the gate insulator, but also at the two interfaces of pentacene/BCP interlayer and pentacene/gate insulator, respectively. The results suggest that the BCP interlayer may be useful to adjust the hole accumulation and transfer, and can increase the hole mobility and output current of OTFTs. The TC-OTFTs with a BCP interlayer at VDS = --20 V showed excellent hole mobility μFE and threshold voltage VTH of 0.58 cm^2/(V-s) and -4.6 V, respectively.展开更多
Using Monte Carlo simulations, we have investigated the classical XY model on triangular lattices of ultra-thin film structures with middle ferromagnetic layers sandwiched between two antiferromagnetic layers. The int...Using Monte Carlo simulations, we have investigated the classical XY model on triangular lattices of ultra-thin film structures with middle ferromagnetic layers sandwiched between two antiferromagnetic layers. The internal energy, the specifc heat, the chirality and the chiral susceptibility are calculated in order to clarify phase transitions and critical phenomena. Prom the finite-size scaling analyses, the values of critical exponents are determined. In a range of interaction parameters, we find that the chirality steeply goes up as temperature increases in a temperature range; correspondingly the value of a critical exponent for this change is estimated.展开更多
文摘Ni-based alloy coating on 21-4-N heat-resistant steel was prepared using CO2 laser, and the high-temperature abrasion wear was tested. The microstructure of this cladding layer and its abrasion wear behavior at high temperature by changing compositions and temperatures were investigated by means of optical microscope and scanning electron microscope. Among the three compositions of cladding layer, i.e. Ni21+20%WC+0.5%CeO2, Ni25+20%WC+0.5%CeO2 and Ni60+20%WC+0.5%CeO2, the experimental results show that Ni21+20%WC+ 0.5%CeO2 cladding layer is made up of finer grains, and presents the best abrasion wear behavior at high temperature. The wear pattern of laser cladding layer is mainly grain abrasion at lower temperature, and it would be changed to adhesive abrasion and oxide abrasion at higher temperature.
文摘1.IntroductionBoronizing can evidently increase thesurface hardness and wear resistance of me-tallic materials[1].It is simple in technique,not expensive and widely used on tools,diesand some other parts which are easy towear.However the wear mechanism andbehaviour of boronized layer are not clearwhen abraded by mixed abradants such ascoal,hard mineral etc.[2,3].Several metallic materials commonly
文摘Mar and abrasion resistance were investigated by a progressive load scratch test and steel wool abrasion test, respectively. Two acrylic coating systems including trimethylolpropane triacrylate (TMPTA) and pentaerythritol triacrylate (PETA) were prepared. A soft base layer was introduced as an intermediate layer between two different types of top layer and poly (methyl methacrylate) (PMMA) substrate to demonstrate the effect of soft base layer on mar and abrasion resistance. Abrasion damage on the coating surface was found to be less severe, when the soft base layer was incorporated into the coating systems. The reduction in scratch coefficient of friction (SCOF) and surface roughness was also observed. The results suggested that mar and abrasion resistance was greatly influenced by the presence of soft base layer, although different top layers were used. Moreover, it was found that abrasion resistance was further improved as the thicker soft base layer was applied.
文摘A new technique was introduced that TiN permeation layer composed of diffusion and deposition layer was synthesized on the surface of Q235 steel using plasma point discharge and hollow cathode effect, and then TiB2 film was deposited (PVD) on newly-formed surface to create TiN/TiB2 multi-permeation layer. The thickness of this multi-permeation layer is above 10μm and the composition and hardness have graded distribution. It has metallurgical bonding with substrate and the bonding strength is high without any spallation phenomenon. In addition comparative research, between TiN/TiB2 multi-permeation layer and TiB2 film which is directly deposited (PVD) on Q235 steel substrate, on surface appearance, microhardness and friction-abrasion property was carried out. The results show that both of surface consist of uniform, compact and fine cellular structure. Surface microhardness of TiN/TiB2 multi-permeation layer is higher, reaching HV2600; but its average friction coefficient is lower, abrasion crack is shallower and wear resistance is better.
基金supported by the National Natural Science Foundation of China (Grant Nos. 11179003 and 10975164)
文摘Monte Carlo simulations reveal considerable straggling of energy loss by the same ions with the same energy in fully-depleted silicon-on-insulator (FDSOI) devices with ultra-thin sensitive silicon layers down to 2.5 rim. The absolute straggling of deposited energy decreases with decreasing thickness of the active silicon layer. While the relative straggling increases gradually with decreasing thickness of silicon films and exhibits a sharp rise as the thickness of the silicon film descends below a threshold value of 50 nm, with the dispersion of deposited energy ascending above ~10%. Ion species and energy dependence of the energy-loss straggling are also investigated. For a given beam, the dispersion of deposited energy results in large uncertainty on the actual linear energy transfer (LET) of incident ions, and thus single event effect (SEE) responses, which pose great challenges for traditional error rate prediction methods.
基金supported by the National Natural Science Foundation of China(No.51375237)the Natural Science Foundation of Jiangsu Province(No.BK2012796)the Scientific Research Start Project of Talent Introduction of NUAA(No.1005-56YAH)
文摘The formula of the thickness of the heat-insulating layer is deduced via heat transfer analysis,according to the principle of heat transfer in limited space.Polishing experiments are carried out using the same technological parameters.Compared with the polishing experimental results,the heat transfer model is proved to be correct.As validated by the experimental results,polyurethane heat-insulating layer can effectively improve the service life of the ice fixed abrasive pad and alleviate the melting rate in the polishing process to improve the polishing quality proposed.The heat transfer model provides theoretical basis for research of temperature field of ice fixed abrasive polishing.
文摘The abrasive waterjet (AWJ) is now widely used in the advanced cutting processes of polymers,metals,glass,ceramics and composite materials like thin multiple-layered material (TMM).Various research and development efforts have recently been made to understand the science of AWJ.However,the interaction mechanism between a workpiece and high-velocity abrasive particles still remains a complicated problem.In this work,the material removal mechanisms of AWJ such as micro penetration and micro dent were experimentally investigated.In addition,a new computer simulation model considering high strain rate effect was proposed to understand the micro impact behavior of high-velocity micro-sized abrasives in AWJ cutting.
基金Project supported by the National Natural Science Foundation of China (Grant Nos. 61076013, 51272008, and 51102003)the National Basic Research Program of China (Grant No. 2012CB619304)+1 种基金the Beijing Municipal Science & Technology Commission (Grant No. D111100001711002)the Specialized Research Fund for the Doctoral Program of Higher Education, China (Grant No. 20100001120014)
文摘We theoretically investigate the optical properties of an ultra-thin InN layer embedded in InGaN matrix for light emitters. The peak emission wavelength extends from ultraviolet (374 nm) to green (536 nm) with InN quantum well thickness increasing from 1 monolayer to 2 monolayers, while the overlap of electron–hole wave function remains at a high level (larger than 90%). Increase of In content in InGaN matrix provides a better approach to longer wavelength emission, which only reduces the spontaneous emission rate slightly compared with the case of increasing In content of the conventional InGaN quantum well. Also, the transparency carrier density derived from gain spectrum is of the same order as that in the conventional blue laser diode. Our study provides skillful design on the development of novel structure InN-based light emitting diodes as well as laser diodes.
基金supported by the National High Technology Research and Development Program of China (Grant No 2006AA03Z0412)the National Natural Science Foundation of China (Grant Nos 10774013 and 10804006)+4 种基金the Excellent Doctor’s Science and Technology Innovation Foundation of Beijing Jiaotong University (Grant No 48024)the Foundation of Beijing Jiaotong University (Grant No 2005SM057)the Research Fund for the Youth Scholars of the Doctoral Program of Higher Education (Grant No 20070004031)the Beijing NOVA program (Grant No 2007A024)Sponsored by the Scientific Research Foundation for the Returned Overseas Chinese Scholars,State Education Ministry
文摘The properties of top-contact organic thin-film transistors (TC-OTFTs) using ultra-thin 2, 9-dimethyl-4, 7- diphenyl-1, 10-phenanthroline (BCP) as a hole-blocking interlayer have been improved significantly and a BCP interlayer was inserted into the middle of the pentacene active layer. This paper obtains a fire-new transport mode of an OTFT device with double-conductible channels. The accumulation and transfer of the hole carriers arc limited by the BCP interlayer in the vertical region of the channel. A huge amount of carriers is located not only at the interface between pentacene and the gate insulator, but also at the two interfaces of pentacene/BCP interlayer and pentacene/gate insulator, respectively. The results suggest that the BCP interlayer may be useful to adjust the hole accumulation and transfer, and can increase the hole mobility and output current of OTFTs. The TC-OTFTs with a BCP interlayer at VDS = --20 V showed excellent hole mobility μFE and threshold voltage VTH of 0.58 cm^2/(V-s) and -4.6 V, respectively.
基金Project supported by the National Natural Science Foundation of China (Grant No 10234010), Acknowledgements The authors would like to thank Professor T. Horiguch for his useful discussion. 0ur simulations were carried out on IBM RS/6000 SP3 at the Centre for Computational Science and Engineering of Peking University.
文摘Using Monte Carlo simulations, we have investigated the classical XY model on triangular lattices of ultra-thin film structures with middle ferromagnetic layers sandwiched between two antiferromagnetic layers. The internal energy, the specifc heat, the chirality and the chiral susceptibility are calculated in order to clarify phase transitions and critical phenomena. Prom the finite-size scaling analyses, the values of critical exponents are determined. In a range of interaction parameters, we find that the chirality steeply goes up as temperature increases in a temperature range; correspondingly the value of a critical exponent for this change is estimated.