Shaking table test for reinforcement of soil slope with multiple sliding surfaces by reinforced double-row anti-slide piles

Despite the continuous advancements of engineering construction in high-intensity areas,many engineering landslides are still manufactured with huge thrust force,and double-row piles are effective to control such large landslides.In this study,large shaking table test were performed to test and obtain multi-attribute seismic data such as feature image,acceleration,and dynamic soil pressure.Through the feature image processing analysis,the deformation characteristics for the slope reinforced by double-row piles were revealed.By analyzing the acceleration and the dynamic soil pressure time domain,the spatial dynamic response characteristics were revealed.Using Fast Fourier Transform and half-power bandwidth,the damping ratio of acceleration and dynamic soil pressure was obtained.Following that,the Seism Signal was used to calculate the spectral displacement of the accelerations to obtain the regional differences of spectral displacement.The results showed that the overall deformation mechanism of the slope originates from tension failure in the soil mass.The platform at the back of the slope was caused by seismic subsidence,and the peak acceleration ratio was positively correlated with the relative pile heights.The dynamic soil pressure of the front row piles showed an inverted"K"-shaped distribution,but that of the back row piles showed an"S"-shaped distribution.The predominant frequency of acceleration was 2.16 Hz,and the main frequency band was 0.7-6.87 Hz;for dynamic soil pressure,the two parameters became 1.15 Hz and 0.5-6.59 Hz,respectively.In conclusion,dynamic soil pressure was more sensitive to dampening effects than acceleration.Besides,compared to acceleration,dynamic soil pressure exhibited larger loss factors and lower resonance peaks.Finally,back row pile heads were highly sensitive to spectral displacement compared to front row pile heads.These findings may be of reference value for future seismic designs of double-row piles.

Fiber optic monitoring of an anti-slide pile in a retrogressive landslide

Anti-slide piles are one of the most important reinforcement structures against landslides,and evalu-ating the working conditions is of great significance for landslide mitigation.The widely adopted analytical methods of pile internal forces include cantilever beam method and elastic foundation beam method.However,due to many assumptions involved in calculation,the analytical models cannot be fully applicable to complex site situations,e.g.landslides with multi-sliding surfaces and pile-soil interface separation as discussed herein.In view of this,the combination of distributed fiber optic sensing(DFOS)and strain-internal force conversion methods was proposed to evaluate the working conditions of an anti-sliding pile in a typical retrogressive landslide in the Three Gorges reservoir area,China.Brillouin optical time domain reflectometry(BOTDR)was utilized to monitor the strain distri-bution along the pile.Next,by analyzing the relative deformation between the pile and its adjacent inclinometer,the pile-soil interface separation was profiled.Finally,the internal forces of the anti-slide pile were derived based on the strain-internal force conversion method.According to the ratio of calculated internal forces to the design values,the working conditions of the anti-slide pile could be evaluated.The results demonstrated that the proposed method could reveal the deformation pattern of the anti-slide pile system,and can quantitatively evaluate its working conditions.

Research on the Influence of Cutting Condition on the Surface Microstruct ure of Ultra-thin Wall Parts in Ultrasonic Vibration Cutting

In many fields of high-tech industry the ultra-t hi n wall parts are employed. In this paper the experiments were carried out to dis cuss the surface microstructure of the camera’s guided drawtube by applying ult rasonic vibration cutting device to the traditional lathe. The influence rule of the cutting condition on the surface roughness was put forward, which was drawn by comparing the ultrasonic cutting with the common cutting by use of the cemen ted carbide tool and the polycrystalline diamond (PCD) tool. The test results sh owed that the ultrasonic cutting performs better than the common cutting in the same condition. According to the test results analyzing, the surface characteriz ation is influenced clearly by the rigidity of the acoustic system and the machi ne tool, as well the setting height of the tool tip. Otherwise, the dense regula r low frequency vibration ripples will be scraped on the machined surface. When the tool tip is set higher than the rotating center of the work piece by three t imes of the amplitude of ultrasonic vibration, the vibration ripples behave alig ht; they turn light and shade alternatively when the tool tip is lower than the rotating center of the work piece by three times of the amplitude of ultrasonic vibration. According to the test result analyzing, the following conclusions are put forward: 1) The surface roughness in ultrasonic cutting is better than that in common cutting. Under a one third critical cutting velocity, the value of th e surface roughness in ultrasonic cutting rise slightly along with the cutting v elocity, while in common cutting it decreases contrast to the cutting velocity; the curves of the surface roughness in ultrasonic cutting and common cutting see m to be alike, both increase along with the feed rate and the cutting depth, but the value in ultrasonic cutting is smaller in the same condition.2) The influen ce of the coolant on the surface roughness cannot be ignored. The kerosene can b e employed to improve the surface roughness in ultrasonic machining.3) In ultras onic cutting process of aluminum alloy ultra-thin wall work piece, the PCD tool performs better than the cemented carbide tools.4) The vibration ripples result from the not enough rigidity of the acoustic system and the improper setting he ight of the tool tip. The departure of the tool tip from the rotating center of the work piece to some extent causes the vibration ripples on the machined surfa ce.

Ultra-thin and light-weight spoof surface plasmon polariton coupler achieved by broadside coupled split ring resonators

Low profile and light weight are very important for practical applications of a spoof surface plasmon polariton（SSPP）coupler, especially at low frequencies. In this paper, we propose and design an ultra-thin, light-weight SSPP coupler based on broadside coupled split ring resonators（BC-SRRs）. The size of BC-SRR can be far less than λ/100 and can extremely well control the reflective phases within a subwavelength thickness. Due to the broadside capacitive coupling, the electrical size of BC-SRR is dramatically reduced to guarantee the ultra-thin thickness of the SSPP coupler. The weight of the SSPP coupler is reduced by a low occupation ratio of BC-SRR in the unit cell volume. As an example, a C-band SSPP coupler composed of phase gradient BC-SRRs is designed, fabricated, and measured. Due to the ultra-small size and low occupation ratio of BC-SRRs, the thickness of the coupler is λ/12 and the surface density is only 0.98 kg/m^2. Both simulation and experiment results verify that the coupler can achieve high-efficiency SPP coupling at 5.27 GHz under normal incidence.

Numerical Investigations on Fluid Flow and Heat Transfer Characteristics of an Ultra-Thin Heat Pipe with Separated Wick Structures

Thermal and fluid-flow characteristics were numerically analyzed for ultra-thin heat pipes.Many studies have been conducted for ultra-thin heat pipes with a centered wick structure,but this study focused on separated wick structures to increase the evaporation/condensation surface areas within the heat pipe and to reduce the concentration of heat flux within the wick structure.A mathematical heat-pipe model was made in the threedimensional coordinate system,and the model consisted of three regions:a vapor channel,liquid-wick,and container wall regions.The conservation equations for mass,momentum,and energy were solved numerically with boundary conditions by using a code developed by one of the authors.The numerical results with the separated wick structures were compared with those with the centered,which confirmed the effectiveness of the separation of the wick structure.However,the effectiveness of the separation was affected by the position of the separated wick structure.A simple equation was presented to determine the optimum position of the separated wick structures.Numerical analyses were also conducted when the width of the heat pipe was increased with the cooled section,which clarified that the increase in the cooled-section width with the addition of wick structures wasmore effective than the increase in the cooled-section length.A 44%reduction in the total temperature difference of the heat pipe was obtained under the present numerical conditions.Furthermore,a comparison wasmade between experimental results and numerical results.

Effect of ceramic work rolls on surface roughness of rolled SUS304 ultra-thin strips

Surface morphology and roughness are important parameters of surface quality of cold-rolled ultra-thin strip steel.In order to study the effect of Si_(3)N_(4) ceramic work rolls on the surface roughness of SUS304 ultra-thin strip,ABAQUS finite element model calculation,3D laser profilometry,and other methods were adopted based on the physical characteristics of Si_(3)N_(4) ceramic roll and 9Cr2MoV steel roll,like anti-flattening performance and oil wettability.The surface morphology and roughness of SUS304 ultra-thin strip rolled by different material work rolls under oil lubrication conditions were measured.The results showed that under the rolling force of 10 kN,the maximum flattening amount of Si_(3)N_(4) ceramic roll was reduced by 35.14%compared to that of 9Cr2MoV steel roll.The reduction rate of SUS304 ultra-thin strip rolled by ceramic roll was 34.19%,while that rolled by steel roll was only 22%;Si_(3)N_(4) ceramic roll can further increase the number of alternating convex peaks and concave valleys in the rolled thin strip,reduce the profile steepness,reduce surface roughness,and enhance the planarization effect of surface micro-convex bodies,with improving surface quality and surface glossiness.Finally,the mechanism of Si_(3)N_(4) ceramic roll significantly improving the surface roughness of rolled SUS304 ultra-thin strip was proposed.

Numerical Study on Surface Wettability Gradient Enhanced Ultra-Thin Loop Heat Pipe

Loop heat pipes(LHPs),as high-efficiency heat dissipation components,are considered to be superior thermal conductors beyond any known materials.To apply LHPs to mobile electronics,a small,thin and compact system needs to be designed.However,with the trend of miniaturization,the heat transfer performance of LHPs degrades rapidly due to the significant increase of working fluid backflow resistance.This work aims to propose an effective solution to this problem.In this work,the surface wettability gradient(SWG)is introduced into the ultra-thin LHP,and the influence of SWG on mass and heat transfer performance is studied comprehensively by using a transient three-dimensional numerical model.It is observed that the SWG can significantly increase the vapor-liquid circulation efficiency and improve heat transfer performance.Numerical experiments have been performed to compare the two kinds of LHPs with and without SWG.At the heat load of 4–6 W,the start-up time for LHP with SWG is shortened by 11.5%and the thermal resistance is reduced by about 44.3%,compared with the LHP without SWG.This work provides a solution for the performance-degradation problem caused by miniaturization,as a numerical reference for experiments.

Evaporation Heat Transfer Characteristics from a Sintered Powder Wick Structure Sandwiched between Two Solid Walls

An ultra-thin flattened heat pipe has been developed with a centered wick structure.This structure is essential to make the heat pipe thinner.However,the centered wick structure reduces the evaporation and condensation surface areas of the wick structure because it is sandwiched between heat pipe walls.In this study,because detailed discussion has not been made,heat transfer experiments were conducted for the wick structure sandwiched between two solid walls.This study focused on the evaporation heat transfer characteristics from the sandwiched wick structure.The experiments were conducted with three wick structures,that is,strip-shaped sintered copper powders with thicknesses of 0.5,1.0,and 1.5 mm.Water was used as working fluid.The capillary pumping performance,that is,the liquid lifting velocities of the three wick structures were the same.The experimental results of the three wick structures were compared regarding the relation between the evaporation heat transfer rate and the superheat of the working fluid.The heat transfer experiments were also conducted when one of the solid walls was removed from the wick structure.It was confirmed that even if the wick structure was sandwiched between the solid walls,sufficient evaporation of the working fluid occurred from the thin sides of the wick structure.

Simulation of thermal processes in metamaterial millimeter-wave to infrared converter for millimeter-wave imager

The main characteristics of millimeter-wave(MM-wave)image detector were simulated by means of accurate numerical modeling of thermophysical processes in a metamaterial MM-to-IR converter.The converter represents a multilayer structure consisting of an ultra thin resonant metamaterial absorber and a perfect emissive layer.The absorber consists of a dielectric self-supporting film that is metallized from both sides.A micropattern is fabricated from one side.Resonant absorption of the MM waves induces the converter heating that yields enhancement of IR emission from the emissive layer.IR emission is detected by IR camera.In this contribution an accurate numerical model for simulation of the thermal processes in the converter structure was created by using COMSOL Multiphysics software.The simulation results are in a good agreement with experimental results that validates the model.The simulation shows that the real-time operation is provided for the converter thickness less than 3µm and time response can be improved by decreasing of the converter thickness.The energy conversion efficiency of MM waves into IR radiation is over 80%.The converter temperature increase is a linear function of a MM-wave radiation power within three orders of the dynamic range.The blooming effect and ways of its reducing are also discussed.The model allows us to choose the ways of converter structure optimization and improvement of image detector parameters.