Seam Tracking Technology for Hyperbaric Underwater Welding

Automatic weld seam tracking technology to be used in hyperbaric underwater damaged pipeline repair welding is much more important, because of poor bevel preparation and severe working condition. A weld seam tracking system based on digital signal processing（DSP） passive light weld image processing technology has been established. A convenient charge coupled device（CCD） camera system was used in the high pressure environment with the help of an aperture and focus altering mechanism to guarantee overall image visibility in the scope of pressure below 0.7 MPa. The system can be used in the hyperbaric environment to pick up the real welding image of both the welding arc and the welding pool. The newly developed DSP technology was adopted to achieve the goal of system real time characteristics. An effective weld groove edge recognition technique including narrow interesting window opening, middle value wave filtering, Sobel operator weld edge detecting and edge searching in a defined narrow area was proposed to remove the guide error and system accuracy was ensured. The results of tracking simulation and real tracking application with arc striking have proved the validity and the accuracy of the mentioned system and the image processing method.

Research of chamber local dry underwater welding system and drainage properties

Because of relatively large protective area and good underwater welding quality, chamber underwater welding has a great using prospect in spent fuel pool maintenance at nuclear power plant. A chamber local dry automatic underwater welding test system with a data acquisition platform is developed, drainage seal tests in a water tank are carried out and the data acquired from the tests are analyzed. The results show that the chamber local dry underwater welding test system can achieve good drainage seal, the drainage effect is enhanced with the increase of the drainage gas flow rate and the drainage time. The results establish the foundation of the research of chamber local dry underwater welding.

Finite element simulation of three-dimensional temperature field in underwater welding

Mathematical models of three-dimensional temperature fields in underwater welding with moving heat sources are built. Double ellipsoid Gauss model is proposed as heat sources models. Several factors which affect the temperature fields of underwater welding are analyzed. Water has little influence on thermal efftciency. Water convection coefftcient varies with the temperature difference between the water and the workpiece , and water convection makes molten pool freeze quickly. With the increase of water depth, the dimensions of heat sources model should be reduced as arc shrinks. Finite element technology is used to solve mathematical models. ANSYS software is used as finite element tool, and ANSYS Parametric Design Language is used to develop subprograms for loading the moving heat sources and the various convection coefftcients. Experiment results show that computational results by using double ellipsoid Gauss heat sources model accord well with the experimental results.

Microstructure and mechanical properties of E36 steel joint welded by underwater wet welding

The microstructure and mechanical properties of E36 steel joint welded by underwater welding using flux-cored wire are comprehensively investigated. The welding depth, welding current and welding voltage is 4 m, 130 A and 32 V, respectively. The weld metal is ferrite which varies in size, with carbide particles distributed on it, while the microstructure of HAZ is mixture of martensite of different size and some tempered structure. The microhardness of the weld metal is 190 HV. Almost all the tensile specimens fracture in weld metal and the average tensile strength of joint is 390 MPa, which is equal to 80% that of base metal. The tensile fracture morphology of joint presents obviously the characterization of brittle fracture, which displays the features of cleavage fracture and intergranular fracture.

Application of RVM for prediction of bead shape in underwater rotating arc welding

Bead sttape in underwater rotating arc welding was affected by several welding parameters. RVM （ relevance vector machine） was used to build a model to predict weld bead shape. The training data set of RVM eortsists of the welding parameters which are rotational frequency, rotational radius, height of torch and welding current and the features of the bead shape. The maximum error and mean error for prediction of width are 0. 10 mm and 0. 09 mm, respectively, and the maximum error and mean error for prediction of penetration are 0. 31 mm and 0. 12mm, respectively, which are showed that the prediction model can achieve higher prediction precision at reasonably small size of training data set.

Modeling of underwater wet welding seam forming based on support vector machines

Underwater welding is developing fast because of the exploration of marine resources, and underwater wet welding automation is urgently needed because of the rigorous environment. To control the welding process automatically, the model of the process should first be built to predict the current welding process status. In this paper, arc and visual sensors were used simultaneously to obtain the electrical and visual information of underwater wet welding, and support vector machines （SVM） were used to model the process, experiment results showed that the method could effectively use the information obtained and give precise prediction results.

Representation of Dynamic Positioning on Hovering Type Autonomous Underwater Vehicle in Precise Welding Operations

This paper proposes dynamic positioning(DP) on a hovering autonomous underwater vehicle(HAUV) to perform accurate underwater processes such as welding operations. High maneuverability, high controllability, and hovering of the robot were the prerequisites of this operation, which increase its accuracy and velocity and reduce costs and human health risks. Other types of thrusters were used in this robot to reduce the number of thrusters and controller’s complexity. Controlling every 6 degrees of freedom to perform this type of operation was done. Furthermore, such a delicate operation required controlling the translational and rotational movements together. There was also a need to control the velocities to travel in a prescribed distance at a reasonable time. The possibility of dynamic positioning for welding and maintaining position at a point was defined for the robot. Then the robot’s performance under a defective state-servo motor failure, thruster malfunction-and the subsequent effects on the performance during the predetermined missions were investigated. Simulation results demonstrated that the HAUV has the capability to perform dynamic positioning operations. In this article, one of the prevalent classic control methods called PID controller was employed for controlling the movements of the robot.

Underwater Laser Welding/Cladding for High-performance Repair of Marine Metal Materials:A Review

With the rapid developments of marine resource exploitation,mounts of marine engineering equipment are settled on the ocean.When it is not possible to move the damaged equipment into a dry dock,welding operations must be performed in underwater environments.The underwater laser welding/cladding technique is a promising and advanced technique which could be widely applied to the maintenance of the damaged equipment.The present review paper aims to present a critical analysis and engineering overview of the underwater laser welding/cladding technique.First,we elaborated recent advances and key issues of drainage nozzles all over the world.Next,we presented the underwater laser processing and microstructural-mechanical behavior of repaired marine materials.Then,the newly developed powder-feeding based and wire-feeding based underwater laser direct metal deposition techniques were reviewed.The differences between the convection,conduction,and the metallurgical kinetics in the melt pools during underwater laser direct metal deposition and in-air laser direct metal deposition were illustrated.After that,several challenges that need to be overcame to achieve the full potential of the underwater laser welding/cladding technique are proposed.Finally,suggestions for future directions to aid the development of underwater laser welding/cladding technology and underwater metallurgical theory are provided.The present review will not only enrich the knowledge in the underwater repair technology,but also provide important guidance for the potential applications of the technology on the marine engineering.

Study of pores produced in underwater wet welding

This paper deals with the effect of water depth in the range of 10 m to 80 m upon the formation of pores produced during underwater wet welding. The results show that it is easy for the inner pores to occur owing to the particularity of the molten metal solidification that the outer pores begin to appear when the water depth increases to about 60 m, that the porosity increases and pore grows up as the water depth increases, and that pores are all hydrogen-containing ones through the examination of the variation of number of pores with the residual hydrogen and oxygen content in the weld metal.

Effects of process parameters on the depth-to-width ratio of flux-cored wire underwater wet welding

The effects of process parameters on the depth-to-width ratio （D/W） of flux-cored wire underwater wet welding with a certain type of homemade .flux-cored wire are studied. It is found that the welding .speed, wire feeding speed and torch oscillating amplitude hare significant effects on the dopth-to-width ratio （D/W） of welds. The D/W ratio of welds increases significantly with the increase of welding speed without the oscillating of welding torch. It increased （from 0. 14 to 0. 26 ） with the increase of wire feeding speed while the torch oscillating. And it decreased linearly with the increase of torch oscillating amplitude. However, the influelwe of oscillating speed, wire extension and welding voltage on the D/W ratio of welds was not obvious.

Development of underwater wet welding experimental and divers training system

Compared to traditional welding methods, the underwater wet welding is special with many different characteristics due to the unique aqueous environment. It is conducted completely under water by divers and unique welding technology is required in the special operation environment. The operating levels of the divers are the key factor to acquire high quality welded joints. In this paper, an underwater wet welding experimental and divers training system is developed to serve divers training and conducting welding experiments. The system consists of life support system, signals real-time monitoring system and communicating system, etc. An underwater butt welding experiment based on welding electrodes is conducted, and the system works well. It proves that the system can guarantee divers welding safely and successfully and high quality weld seam is expected to be acquired.

Analysis of the electrical conductivity of plasma during underwater wet welding

The electrical conductivity is indispensable for the underwater wet welding arc simulation. In order to get this parameter, the composition of the underwater arc is analyzed, and the electron content is obtained. Then the current formation mechanism in the arc and the effective collision cross-sectional area between the electron and ions is discussed. The calculation methods and results analysis are presented in this paper.

Study of gas shielding stability for underwater local dry welding based on FLUENT

The research of gas shielding stability technology, playing a key role in underwater local dry welding, was introduced in this paper. The study includes shielding cup design, gas flow simulation, draining and welding experiments. The commercial computational fluid dynamics （ CFD ） software FLUENT was applied to get and compare the speed and pressure contour images of gas in the three kinds of cup with different intake mode. The computed results show that the cup with stilling chamber on the top has the best shielding performance. The underwater welding experiment of 15 meters proves that the shielding cup with stilling chamber can offer a good dry space, the welding arc can burn stably in it and the weld quality is perfect. The research will facilitate the application of underwater local dry welding technology in the maintenance of nuclear power station widely.

A novel wavelet method for electric signals analysis in underwater arc welding

Electric signals are acquired and analyzed in order to monitor the underwater arc welding process. Voltage break point and magnitude are extracted by detecting arc voltage singularity through the modulus maximum wavelet （MMW） method. A novel threshold algorithm, which compromises the hard-threshold wavelet （HTW） and soft-threshold wavelet （STW） methods, is investigated to eliminate welding current noise. Finally, advantages over traditional wavelet methods are verified by both simulation and experimental results.

Finite element analysis of the angular distortion and residual stress in underwater wet welding

In underwater environment, the shape, voltage, and energy density of the welding arc vary because of the high pressure and there are notable changes in workpiece cooling conditions due to the strong cooling effect of water. As a result, there are clear differences between the residual stress and thermal distortion in underwater wet welding and those in conventional welding （in air）. Considering these process features, a thermo-mechanical finite element model of underwater wet bead-on-plate welding was established. The influences of the water compressing action to the arc and the enhanced heat losses caused by the surrounding water on the residual stress and the angular distortion of the workpiece were analyzed. Results show that the angular distortion gets smaller in deeper water, and that the longitudinal residual stress gets smaller as water flows faster.

Microstructure evolution of HAZ in the multi-pass underwater wet welded joints

The microstructure evolution of heat-affected zone （HAZ） in the multi-pass underwater welded joints is investigated in the present work, and it can be characterized by four zones, marked as Region A, B, C and D, respectively. The microstructure in Region A is the mixture of lath martensite and residual austenite. Besides this structure, lots of acicular ferrite appears in Region B as well, and the grain size becomes larger. Lath ferrite combined with granular bainite is observed in Region C. In Region D, tempered sorbite, granular bainite and fine acicular ferrite are found within the grains, while massive ferrite and Widmanstatten structure are distributed along the grain boundary： The thermal effect of multi-pass welding makes the microstructure and property more and more uniform in the ttAZ, and the largest hardness 356 HV in the HAZ appears in Region A.

Effects of welding voltage on process stability in hyperbaric gas metal arc welding

Based on hyperbaric gas metal arc welding （GMAW） experiments at ambient pressure of 0. 8 MPa, the process stability of different welding voltages was studied. The experiments were carried out with a high speed camera system including infrared laser backlight and electric signal acquisition system. Keeping wire feed speed at 8 m/min, arc length increases linearly with the increase of welding voltage in O. 8 MPa argon environment. Under this condition, all the metal transfer modes are droplet repelled transfer and the transfer frequency increases with increasing welding voltage. The number of deviating spatter is less with relatively high welding voltage. The results of electric signal waveforms show that the probabilities of short circuit and arc interruption decrease firstly and then increase with increasing welding voltage. When the welding voltage is 37 V, the hyperbaric welding process is the most stable with no probability of short circuit and arc interruption.

Experimental and numerical investigation on under-water friction stir welding of armour grade AA2519-T87 aluminium alloy

Friction stir welding(FSW) is a promising welding process that can join age hardenable aluminium alloys with high joint efficiency. However,the thermal cycles experienced by the material to be joined during FSW resulted in the deterioration of mechanical properties due to the coarsening and dissolution of strengthening precipitates in the thermo-mechanical affected zone(TMAZ) and heat affected zone(HAZ). Under water friction stir welding(UWFSW) is a variant of FSW process which can maintain low heat input as well as constant heat input along the weld line. The heat conduction and dissipation during UWFSW controls the width of TMAZ and HAZ and also improves the joint properties. In this investigation, an attempt has been made to evaluate the mechanical properties and microstructural characteristics of AA2519-T87 aluminium alloy joints made by FSW and UWFSW processes. Finite element analysis has been used to estimate the temperature distribution and width of TMAZ region in both the joints and the results have been compared with experimental results and subsequently correlated with mechanical properties.? 2016 China Ordnance Society. Production and hosting by Elsevier B.V. All rights reserved.

Metallurgical and Mechanical Properties of Underwater Laser Welds of Stainless Steel

In this paper, the microstructures and mechanical properties of underwater laser welds of Type 304 stainless steel were investigated. JISY308L type filler wire was used as filler wire during welding. A gas-shielding nozzle was used to form a local dry cavity surrounding the welding zone. The main results are summarized as follows: (1) The shielding condition of the local dry cavity severely affects the oxygen content of the weld, the worst shielding condition leading to the oxygen content of 800×10-6, which largely increases the oxide inclusions and somewhat reduces the ferrite content. (2) The increase of oxygen content reduces the elongation rate and reduction of area in tensile test, but has no influence on the tensile strength. (3) In appropriate shielding condition, the mechanical properties of the underwater laser welds can be as same as that in the air.

Dissimilar friction stir spot welding of AA2024-T3/AA7075-T6 aluminum alloys under different welding parameters and media

This paper studies the friction stir spot welding of AA2024-T3/AA7075-T6 Al alloys in the ambient and underwater environments by clarifying the nugget features,microstructure,fracture and mechanical properties of the joints.The results show that the water-cooling medium exhibits a significant heat absorption capacity in the AA2024-T3/AA7075-T6 welded joint.Nugget features such as stir zone width,circular imprints,average grain sizes,and angular inter-material hooking are reduced by the watercooling effect in the joints.Narrower whitish(intercalated structures)bands are formed in the underwater joints while Mg2Si and Al2CuMg precipitates are formed in the ambient and the underwater welded joints respectively.An increase in tool rotational speed(600e1400 rpm)and plunge depth(0.1 e0.5 mm)increases the tensile-shear force of the welded AA2024-T3/AA7075-T6 joints in both the ambient and underwater environments.The maximum tensile-shear forces of 5900 N and 6700 N were obtained in the ambient and the underwater welds respectively.