CdS thin films were prepared by chemical-bath-deposited method and the effect of temperature and time on the properties of CdS thin films was studied. Independent of the deposited temperature, the growth was mainly co...CdS thin films were prepared by chemical-bath-deposited method and the effect of temperature and time on the properties of CdS thin films was studied. Independent of the deposited temperature, the growth was mainly controlled by the ion-by-ion growth mechanism at the beginning of the film deposition, then the cluster-by-cluster mechanism came to be dominant. The growth rate increased faster with the increasing of temperature until the thickness reached the limitation, then thickness instead become thinner. The scanning electron micro- scope results revealed that the morphology of the CdS film changed from pinholes to rough, inhomogeneous surface with increasing deposition time and deposition temperature. The X- ray diffraction results showed the film structure was a mixture of two phases： hexagonal and cubic, and it was very important to controll deposition time to the film＇s crystal phase. All films in depth of approxilnate 100 nm existed above 65% transmittance, the absorption edge became ＂red-shift＂ with temperature rising. At 60 and 70℃, with 20 min deposited-time, the energy band gap was more than 2.42 eV and decreased with time, while at 80 and 90℃ the energy band gap was less than 2.42 eV and increased little when the time changed from 10min to 15 nfin at 80℃.展开更多
CdS thin films were deposited by the ion layer gas reaction (TLGAR) method.Structural, chemical, topographical development as well as optical and electrical properties ofas-deposited and annealed thin films were inves...CdS thin films were deposited by the ion layer gas reaction (TLGAR) method.Structural, chemical, topographical development as well as optical and electrical properties ofas-deposited and annealed thin films were investigated by XRD, SEM, XPS, AFM and UV-VIS. The resultsshowed that the thin films are uniform, compact and good in adhesion to the substrates, and thegrowth of the films is 2.8 nm/cycle. The evolution of structure undergoes from the cubic structureto the hexagonal one with a preferred orientation along the (002) plane after annealing at 673 K. Anamount of C, O and Cl impurities can be reduced by increasing the drying temperature or byannealing in N2 atmosphere. It was found that the band gap of the CdS films shifts to higherwavelength after annealing or increasing film thickness. The electrical resistivity decreases withincreasing annealing temperature and film thickness.展开更多
Contour dynamics (CD) method for the motions of typhoon is presented in this paper. The effect of asymmetric inner structure on the typhoon'sanomalous track has been discussed in different environmental steering. ...Contour dynamics (CD) method for the motions of typhoon is presented in this paper. The effect of asymmetric inner structure on the typhoon'sanomalous track has been discussed in different environmental steering. Todemonstrate the feasibility of the method, the track of Typhoon Yancy(9012) isconcerned with. The numerical results show that the method can describe the tendency of looping qualitatively.展开更多
Nanowires have recently attracted more attention because of their low-dimensional structure, tunable optical and electrical properties for next-generation nanoscale optoelectronic devices. Cd S nanowire array, which i...Nanowires have recently attracted more attention because of their low-dimensional structure, tunable optical and electrical properties for next-generation nanoscale optoelectronic devices. Cd S nanowire array, which is(002)-orientation growth and approximately perpendicular to Cd foil substrate, has been fabricated by the solvothermal method. In the temperature-dependent photoluminescence, from short wavelength to long wavelength, four peaks can be ascribed to the emissions from the bandgap, the transition from the holes being bound to the donors or the electrons being bound to the acceptors, the transition from Cd interstitials to Cd vacancies, and the transition from S vacancies to the valence band,respectively. In the photoluminescence of 10 K, the emission originated from the bandgap appears in the form of multiple peaks. Two stronger peaks and five weaker peaks can be observed. The energy differences of the adjacent peaks are close to 38 me V, which is ascribed to the LO phonon energy of Cd S. For the multiple peaks of bandgap emission, from low energy to high energy, the first, second, and third peaks are contributed to the third-order, second-order, and first-order phonon replica of the free exciton A, respectively;the fourth peak is originated from the free exciton A;the fifth peak is contributed to the first-order phonon replica of the excitons bound to neutral donors;the sixth and seventh peaks are originated from the excitons bound to neutral donors and the light polarization parallel to the c axis of hexagonal Cd S, respectively.展开更多
The titanium oxide （TiO2） nanotubes have attracted attention for their use in dye-sensitized solar cells as photoanode. In this study semiconducting cadmium sulfide （CdS） nanoparticles arc grown on top opened TiO2...The titanium oxide （TiO2） nanotubes have attracted attention for their use in dye-sensitized solar cells as photoanode. In this study semiconducting cadmium sulfide （CdS） nanoparticles arc grown on top opened TiO2 nanotubes arrays by radio-frequency magnetron sputtering. X-ray diffraction, scanning electron mieroscopy, transmission electron microscopy and diffuse reflection spectra are used to study structural, morphological and optical properties of the CdS/TiO2 bilayer.展开更多
Ab initio calculations are performed on the electronic, structural, elastic and optical properties of the cubic per- ovskite KCdF3. Tile Kohn Sham equations are solved by applying the full potential linearized augment...Ab initio calculations are performed on the electronic, structural, elastic and optical properties of the cubic per- ovskite KCdF3. Tile Kohn Sham equations are solved by applying the full potential linearized augmented plane wave （FP-LAPW） method. The exchange correlation effects are included through the local density approximation （LDA ）, generalized gradient approximation （GGA） and modified Becke-Johnson （mBJ） exchange potential The calculated lattice constant is in good agreement with the experimental result. The elastic properties such as elastic constants, anisotropy factor, shear modulus, Young＇s modulus and Poisson＇s ratio are calculated. KCdF3 is ductile and elastically anisotropic. The calculations of the electronic band structure, density of states （DOS） and charge density show that this compound has an indirect energy band gap （M-F） with a mixed ionic and covalent bonding. The contribution of the different bands is analyzed from the total and partial density of states curves. Optical response of the dielectric functions, optical reflectivity, absorption coefficient, real part of optical conductivity, refractive index, extinction coefficient and electron energy loss, are presented for the energy range of O-40eV. The compound KCdF3 can be used for high-frequency optical and optoelectronic devices.展开更多
In this study, we will introduce the modified (G'/G<sup>2</sup>)-expansion method to explore some of the exact traveling wave solutions of some nonlinear partial differential equations namely, Phi-4 eq...In this study, we will introduce the modified (G'/G<sup>2</sup>)-expansion method to explore some of the exact traveling wave solutions of some nonlinear partial differential equations namely, Phi-4 equation, Joseph-Egri (TRLW) equation, and Calogro-Degasperis (CD) equation. As a result, we have obtained solutions for the equations expressed in terms of trigonometric, hyperbolic and rational functions. Moreover, some selected solutions are plotted using some specific values for the parameters.展开更多
The CdS nanoparticles with good crystallinity were prepared by hydrothermal method in microemulsion composed of poly oxyethylene lauryl ether/water/ cyclohexane/butanol. The structure and the size of the nanoparticles...The CdS nanoparticles with good crystallinity were prepared by hydrothermal method in microemulsion composed of poly oxyethylene lauryl ether/water/ cyclohexane/butanol. The structure and the size of the nanoparticles were analyzed by TEM and XRD. The UV-Vis optical absorption of the samples was also investigated.The results show that hydrothermal treatment is an effective method to prepare CdS nanoparticles of hexagonal structure at low temperature. The particles were in dimensional uniformity. The diameter of the nanoparticles decreased with the increase of the molar ratio of water to surfactant. The minimum diameter of the nanoparticles prepared in this work was 10 nm. Obvious blue-shift were observed in the UV-Vis absorption.展开更多
文摘CdS thin films were prepared by chemical-bath-deposited method and the effect of temperature and time on the properties of CdS thin films was studied. Independent of the deposited temperature, the growth was mainly controlled by the ion-by-ion growth mechanism at the beginning of the film deposition, then the cluster-by-cluster mechanism came to be dominant. The growth rate increased faster with the increasing of temperature until the thickness reached the limitation, then thickness instead become thinner. The scanning electron micro- scope results revealed that the morphology of the CdS film changed from pinholes to rough, inhomogeneous surface with increasing deposition time and deposition temperature. The X- ray diffraction results showed the film structure was a mixture of two phases： hexagonal and cubic, and it was very important to controll deposition time to the film＇s crystal phase. All films in depth of approxilnate 100 nm existed above 65% transmittance, the absorption edge became ＂red-shift＂ with temperature rising. At 60 and 70℃, with 20 min deposited-time, the energy band gap was more than 2.42 eV and decreased with time, while at 80 and 90℃ the energy band gap was less than 2.42 eV and increased little when the time changed from 10min to 15 nfin at 80℃.
文摘CdS thin films were deposited by the ion layer gas reaction (TLGAR) method.Structural, chemical, topographical development as well as optical and electrical properties ofas-deposited and annealed thin films were investigated by XRD, SEM, XPS, AFM and UV-VIS. The resultsshowed that the thin films are uniform, compact and good in adhesion to the substrates, and thegrowth of the films is 2.8 nm/cycle. The evolution of structure undergoes from the cubic structureto the hexagonal one with a preferred orientation along the (002) plane after annealing at 673 K. Anamount of C, O and Cl impurities can be reduced by increasing the drying temperature or byannealing in N2 atmosphere. It was found that the band gap of the CdS films shifts to higherwavelength after annealing or increasing film thickness. The electrical resistivity decreases withincreasing annealing temperature and film thickness.
文摘Contour dynamics (CD) method for the motions of typhoon is presented in this paper. The effect of asymmetric inner structure on the typhoon'sanomalous track has been discussed in different environmental steering. Todemonstrate the feasibility of the method, the track of Typhoon Yancy(9012) isconcerned with. The numerical results show that the method can describe the tendency of looping qualitatively.
基金Project supported by the Natural Science Foundation of Henan Province,China(Grant No.202300410304)Key Research Project for Science and Technology of the Education Department of Henan Province,China(Grant No.21A140021)。
文摘Nanowires have recently attracted more attention because of their low-dimensional structure, tunable optical and electrical properties for next-generation nanoscale optoelectronic devices. Cd S nanowire array, which is(002)-orientation growth and approximately perpendicular to Cd foil substrate, has been fabricated by the solvothermal method. In the temperature-dependent photoluminescence, from short wavelength to long wavelength, four peaks can be ascribed to the emissions from the bandgap, the transition from the holes being bound to the donors or the electrons being bound to the acceptors, the transition from Cd interstitials to Cd vacancies, and the transition from S vacancies to the valence band,respectively. In the photoluminescence of 10 K, the emission originated from the bandgap appears in the form of multiple peaks. Two stronger peaks and five weaker peaks can be observed. The energy differences of the adjacent peaks are close to 38 me V, which is ascribed to the LO phonon energy of Cd S. For the multiple peaks of bandgap emission, from low energy to high energy, the first, second, and third peaks are contributed to the third-order, second-order, and first-order phonon replica of the free exciton A, respectively;the fourth peak is originated from the free exciton A;the fifth peak is contributed to the first-order phonon replica of the excitons bound to neutral donors;the sixth and seventh peaks are originated from the excitons bound to neutral donors and the light polarization parallel to the c axis of hexagonal Cd S, respectively.
文摘The titanium oxide （TiO2） nanotubes have attracted attention for their use in dye-sensitized solar cells as photoanode. In this study semiconducting cadmium sulfide （CdS） nanoparticles arc grown on top opened TiO2 nanotubes arrays by radio-frequency magnetron sputtering. X-ray diffraction, scanning electron mieroscopy, transmission electron microscopy and diffuse reflection spectra are used to study structural, morphological and optical properties of the CdS/TiO2 bilayer.
基金Supported by UGC,New Delhi through UGC-BSR(JRF)fellowships
文摘Ab initio calculations are performed on the electronic, structural, elastic and optical properties of the cubic per- ovskite KCdF3. Tile Kohn Sham equations are solved by applying the full potential linearized augmented plane wave （FP-LAPW） method. The exchange correlation effects are included through the local density approximation （LDA ）, generalized gradient approximation （GGA） and modified Becke-Johnson （mBJ） exchange potential The calculated lattice constant is in good agreement with the experimental result. The elastic properties such as elastic constants, anisotropy factor, shear modulus, Young＇s modulus and Poisson＇s ratio are calculated. KCdF3 is ductile and elastically anisotropic. The calculations of the electronic band structure, density of states （DOS） and charge density show that this compound has an indirect energy band gap （M-F） with a mixed ionic and covalent bonding. The contribution of the different bands is analyzed from the total and partial density of states curves. Optical response of the dielectric functions, optical reflectivity, absorption coefficient, real part of optical conductivity, refractive index, extinction coefficient and electron energy loss, are presented for the energy range of O-40eV. The compound KCdF3 can be used for high-frequency optical and optoelectronic devices.
文摘In this study, we will introduce the modified (G'/G<sup>2</sup>)-expansion method to explore some of the exact traveling wave solutions of some nonlinear partial differential equations namely, Phi-4 equation, Joseph-Egri (TRLW) equation, and Calogro-Degasperis (CD) equation. As a result, we have obtained solutions for the equations expressed in terms of trigonometric, hyperbolic and rational functions. Moreover, some selected solutions are plotted using some specific values for the parameters.
文摘The CdS nanoparticles with good crystallinity were prepared by hydrothermal method in microemulsion composed of poly oxyethylene lauryl ether/water/ cyclohexane/butanol. The structure and the size of the nanoparticles were analyzed by TEM and XRD. The UV-Vis optical absorption of the samples was also investigated.The results show that hydrothermal treatment is an effective method to prepare CdS nanoparticles of hexagonal structure at low temperature. The particles were in dimensional uniformity. The diameter of the nanoparticles decreased with the increase of the molar ratio of water to surfactant. The minimum diameter of the nanoparticles prepared in this work was 10 nm. Obvious blue-shift were observed in the UV-Vis absorption.
