In this paper the Expendable Pattern Casting with dry sand Vacuum(EPC-V) process is used to manufacture iron matrix composites with tungsten carbide particle.Microstructures of the composites layers were analyzed.The ...In this paper the Expendable Pattern Casting with dry sand Vacuum(EPC-V) process is used to manufacture iron matrix composites with tungsten carbide particle.Microstructures of the composites layers were analyzed.The abrasive wear resistance of the composites layers were tested and compared with that of high chromium cast iron.The results show that the iron matrix composites with tungsten carbide particle have high hardness.The abrasive wear resistance of composites with tungsten carbide particle is higher than that of high chromium cast iron.The properties of the matrix materials have been improved remarkably.展开更多
The behavior of transversal cracks on the surface of the slab corner during vertical and horizontal （V-H） rolling process with flat vertical roll and groove vertical roll was simulated by explicit dynamic finite ele...The behavior of transversal cracks on the surface of the slab corner during vertical and horizontal （V-H） rolling process with flat vertical roll and groove vertical roll was simulated by explicit dynamic finite element method. The closure and growth of crack and the contact pressure on surfaces of the crack in contacting zone between slab and roll during rolling process were analyzed. The results showed that during vertical rolling process, when the groove vertical roll is used, the maximum contact pressure on surfaces of the crack is 115 MPa, and the closure of crack is stable when the flat vertical roll is used, the maximum contact pressure on surfaces of the crack is 70 MPa, and it fluctuates greatly. During horizontal rolling process, when groove vertical roll is used, the contact pressure becomes zero which may accelerate the growth of crack when flat vertical roll is used, there is still contact pressure. The cal culated results are in good agreement with the results of test.展开更多
EVA plastic film is the key material for V-process. Through decades of research, special EVA film for V-process has been produced. The film has adequate elongation; its maximum is about 800% in longitudinal direction ...EVA plastic film is the key material for V-process. Through decades of research, special EVA film for V-process has been produced. The film has adequate elongation; its maximum is about 800% in longitudinal direction and 750% in transversal direction. The single width of the film is 2.8 m and the double width is 5.6 m, which is the widest sheet film for V-process in China. Sheets with different thickness ranging from the thickest 0.35 mm to the thinnest 0.08 mm can meet different demands in China. The film can be used not only for V-process of iron castings, but also for the manganese steel railway frog, steel rocking support and side frame castings for train and the steel bridge box for engine truck.展开更多
Poor ductility is the primary concern of magnesium matrix composites(MMCs)inflicted by non-deformable ceramic particle reinforcements.Metal particles which melt at elevated temperature can be used as reinforcement to ...Poor ductility is the primary concern of magnesium matrix composites(MMCs)inflicted by non-deformable ceramic particle reinforcements.Metal particles which melt at elevated temperature can be used as reinforcement to improve the deformation characteristics.Ti-6Al-4V particles reinforced AZ31 MMCs were produced through friction stir processing(FSP)which was carried out in a traditional vertical milling machine.The microstructural features as well as the response to external tensile load were explored.A homogenous distribution of Ti-6Al-4V was achieved at every part of the stir zone.There was no chemical decomposition of Ti-6Al-4V.Further,Ti-6Al-4V did not react with Al and Zn present in AZ31 alloy to form new compounds.A continuous strong interface was obtained around Ti-6Al-4V particle with the matrix.Ti-6Al-4V particles underwent breakage during processing due to severe plastic strain.There was a remarkable refinement of grains in the composite caused by dynamic recrystallization in addition to the pinning of smaller size broken particles.Dense dislocations were observed in the matrix because of plastic deformation and the associated strain misfit.Ti-6Al-4V particles improved the tensile behavior and assisted to obtain appreciable deformation before fracture.Brittle mode of failure was avoided.展开更多
At present,there are many studies on the residual stress field and plastic strain field introduced by surface strengthening,which can well hinder the initiation of early fatigue cracks and delay the propagation of fat...At present,there are many studies on the residual stress field and plastic strain field introduced by surface strengthening,which can well hinder the initiation of early fatigue cracks and delay the propagation of fatigue cracks.However,there are few studies on the effects of these key factors on fretting wear.In the paper,shot-peening(SP)and ultrasonic surface rolling process(USRP)were performed on Ti-6Al-4V plate specimens.The surface hardness and residual stresses of the material were tested by vickers indenter and X-ray diffraction residual stress analyzer.Microhardness were measured by HXD-1000MC/CD micro Vickers hardness tester.The effects of different surface strengthening on its fretting fatigue properties were verified by fretting fatigue experiments.The fretting fatigue fracture surface and wear morphology of the specimens were studied and analyzed by means of microscopic observation,and the mechanism of improving fretting fatigue life by surface strengthening process was further explained.After USRP treatment,the surface roughness of Ti-6Al-4V is significantly improved.In addition,the microhardness of the specimen after SP reaches the maximum at 80μm from the surface,which is about 123%higher than that of the AsR specimen.After USRP,it reaches the maximum at 150μm from the surface,which is about 128%higher than that of AsR specimen.It is also found that the residual compressive stress of the specimens treated by USRP and SP increases first and then decreases with the depth direction,and the residual stress reaches the maximum on the sub surface.The USRP specimen reaches the maximum value at 0.18 mm,about−550 MPa,while the SP specimen reaches the maximum value at 0.1 mm,about−380 MPa.The fretting fatigue life of Ti-6Al-4V effectively improved after USRP and SP.The surface integrity of specimens after USRP is the best,which has deeper residual compressive stress layer and more refined grain.In this paper,a fretting wear device is designed to carry out fretting fatigue experiments on specimens with different surface strengthening.展开更多
Laser direct deposition （LDD） of metallic components is an advanced technology of combining CAD/CAM （computer aided design/computer aided manufacturing）, high power laser, and rapid prototyping. This technology us...Laser direct deposition （LDD） of metallic components is an advanced technology of combining CAD/CAM （computer aided design/computer aided manufacturing）, high power laser, and rapid prototyping. This technology uses laser beam to melt the powders fed coaxiaUy into the molten pool by the laser beam to fabricate fuUy dense metallic components. The present article mainly studies the LDD of Ti-6Al-4V alloy, which can be used to fabricate aircraft components. The mechanical properties of the Ti-6Al-4V alloy, fabricated by LDD, are obtained using the tension test, and the oxygen content of used powders and deposited specimens are measured. In the present article, it can be seen that the mechanical properties obtained using this method are higher than the ones obtained by casting, and equal to those got by wrought anneal. One aircraft part has been made using the LDD process. Because of this aircraft part, with sophisticated shape, the effect of the laser scanning track on the internal soundness of the deposited part was discussed.展开更多
In recent years, Empirical mode decomposition and Hilbert spectral analysis have been combined to identify system parameters. Singular-Value Decomposition is pro- posed as a signal preprocessing technique of Hilbert-H...In recent years, Empirical mode decomposition and Hilbert spectral analysis have been combined to identify system parameters. Singular-Value Decomposition is pro- posed as a signal preprocessing technique of Hilbert-Huang Transform to extract modal parameters for closely spaced modes and low-energy components. The proposed method is applied to a simulated airplane model built in Automatic Dynamic Analysis of Mechanical Systems software. The results demonstrate that the identified modal parameters are in good agreement with the baseline model.展开更多
文摘In this paper the Expendable Pattern Casting with dry sand Vacuum(EPC-V) process is used to manufacture iron matrix composites with tungsten carbide particle.Microstructures of the composites layers were analyzed.The abrasive wear resistance of the composites layers were tested and compared with that of high chromium cast iron.The results show that the iron matrix composites with tungsten carbide particle have high hardness.The abrasive wear resistance of composites with tungsten carbide particle is higher than that of high chromium cast iron.The properties of the matrix materials have been improved remarkably.
基金ItemSponsored by State Ministry of Science and Technology of China (G2000067208-4)
文摘The behavior of transversal cracks on the surface of the slab corner during vertical and horizontal （V-H） rolling process with flat vertical roll and groove vertical roll was simulated by explicit dynamic finite element method. The closure and growth of crack and the contact pressure on surfaces of the crack in contacting zone between slab and roll during rolling process were analyzed. The results showed that during vertical rolling process, when the groove vertical roll is used, the maximum contact pressure on surfaces of the crack is 115 MPa, and the closure of crack is stable when the flat vertical roll is used, the maximum contact pressure on surfaces of the crack is 70 MPa, and it fluctuates greatly. During horizontal rolling process, when groove vertical roll is used, the contact pressure becomes zero which may accelerate the growth of crack when flat vertical roll is used, there is still contact pressure. The cal culated results are in good agreement with the results of test.
文摘EVA plastic film is the key material for V-process. Through decades of research, special EVA film for V-process has been produced. The film has adequate elongation; its maximum is about 800% in longitudinal direction and 750% in transversal direction. The single width of the film is 2.8 m and the double width is 5.6 m, which is the widest sheet film for V-process in China. Sheets with different thickness ranging from the thickest 0.35 mm to the thinnest 0.08 mm can meet different demands in China. The film can be used not only for V-process of iron castings, but also for the manganese steel railway frog, steel rocking support and side frame castings for train and the steel bridge box for engine truck.
文摘Poor ductility is the primary concern of magnesium matrix composites(MMCs)inflicted by non-deformable ceramic particle reinforcements.Metal particles which melt at elevated temperature can be used as reinforcement to improve the deformation characteristics.Ti-6Al-4V particles reinforced AZ31 MMCs were produced through friction stir processing(FSP)which was carried out in a traditional vertical milling machine.The microstructural features as well as the response to external tensile load were explored.A homogenous distribution of Ti-6Al-4V was achieved at every part of the stir zone.There was no chemical decomposition of Ti-6Al-4V.Further,Ti-6Al-4V did not react with Al and Zn present in AZ31 alloy to form new compounds.A continuous strong interface was obtained around Ti-6Al-4V particle with the matrix.Ti-6Al-4V particles underwent breakage during processing due to severe plastic strain.There was a remarkable refinement of grains in the composite caused by dynamic recrystallization in addition to the pinning of smaller size broken particles.Dense dislocations were observed in the matrix because of plastic deformation and the associated strain misfit.Ti-6Al-4V particles improved the tensile behavior and assisted to obtain appreciable deformation before fracture.Brittle mode of failure was avoided.
基金Supported by National Key Research and Development Project(Grant No.2018YFC1902400)Natural Science Foundation of Shanghai(Grant No.20ZR1415300).
文摘At present,there are many studies on the residual stress field and plastic strain field introduced by surface strengthening,which can well hinder the initiation of early fatigue cracks and delay the propagation of fatigue cracks.However,there are few studies on the effects of these key factors on fretting wear.In the paper,shot-peening(SP)and ultrasonic surface rolling process(USRP)were performed on Ti-6Al-4V plate specimens.The surface hardness and residual stresses of the material were tested by vickers indenter and X-ray diffraction residual stress analyzer.Microhardness were measured by HXD-1000MC/CD micro Vickers hardness tester.The effects of different surface strengthening on its fretting fatigue properties were verified by fretting fatigue experiments.The fretting fatigue fracture surface and wear morphology of the specimens were studied and analyzed by means of microscopic observation,and the mechanism of improving fretting fatigue life by surface strengthening process was further explained.After USRP treatment,the surface roughness of Ti-6Al-4V is significantly improved.In addition,the microhardness of the specimen after SP reaches the maximum at 80μm from the surface,which is about 123%higher than that of the AsR specimen.After USRP,it reaches the maximum at 150μm from the surface,which is about 128%higher than that of AsR specimen.It is also found that the residual compressive stress of the specimens treated by USRP and SP increases first and then decreases with the depth direction,and the residual stress reaches the maximum on the sub surface.The USRP specimen reaches the maximum value at 0.18 mm,about−550 MPa,while the SP specimen reaches the maximum value at 0.1 mm,about−380 MPa.The fretting fatigue life of Ti-6Al-4V effectively improved after USRP and SP.The surface integrity of specimens after USRP is the best,which has deeper residual compressive stress layer and more refined grain.In this paper,a fretting wear device is designed to carry out fretting fatigue experiments on specimens with different surface strengthening.
基金This work was supported by the National Natural Science Foundation of China （No. 50331010）
文摘Laser direct deposition （LDD） of metallic components is an advanced technology of combining CAD/CAM （computer aided design/computer aided manufacturing）, high power laser, and rapid prototyping. This technology uses laser beam to melt the powders fed coaxiaUy into the molten pool by the laser beam to fabricate fuUy dense metallic components. The present article mainly studies the LDD of Ti-6Al-4V alloy, which can be used to fabricate aircraft components. The mechanical properties of the Ti-6Al-4V alloy, fabricated by LDD, are obtained using the tension test, and the oxygen content of used powders and deposited specimens are measured. In the present article, it can be seen that the mechanical properties obtained using this method are higher than the ones obtained by casting, and equal to those got by wrought anneal. One aircraft part has been made using the LDD process. Because of this aircraft part, with sophisticated shape, the effect of the laser scanning track on the internal soundness of the deposited part was discussed.
文摘In recent years, Empirical mode decomposition and Hilbert spectral analysis have been combined to identify system parameters. Singular-Value Decomposition is pro- posed as a signal preprocessing technique of Hilbert-Huang Transform to extract modal parameters for closely spaced modes and low-energy components. The proposed method is applied to a simulated airplane model built in Automatic Dynamic Analysis of Mechanical Systems software. The results demonstrate that the identified modal parameters are in good agreement with the baseline model.
