Dynamic response of UHMWPE plates under combined shock and fragment loading

Ultra-high molecular weight polyethylene(UHMWPE)fiber composite has been extensively used to construct lightweight protective structures against ballistic impacts,yet little is known about its performance when subjected to combined blast and fragment impacts.Built upon a recently developed laboratory-scale experimental technique to generate simulated combined loading through the impact of a fragment-foam composite projectile launched from a light gas gun,the dynamic responses of fullyclamped UHMWPE plates subjected to combined loading were characterized experimentally,with corresponding deformation and failure modes compared with those measured with simulated blast loading alone.Subsequently,to explore the underlying physical mechanisms,three-dimensional(3D)numerical simulations with the method of finite elements(FE)were systematically carried out.Numerical predictions compared favorably well with experimental measurements,thus validating the feasibility of the established FE model.Relative to the case of blast loading alone,combined blast and fragment loading led to larger maximum deflections of clamped UHMWPE plates.The position of the FSP in the foam sabot affected significantly the performance of a UHMWPE target,either enhancing or decreasing its ballistic resistance.When the blast loading and fragment impact arrived simultaneously at the target,its ballistic resistance was superior to that achieved when subjected to fragment impact alone,and benefited from the accelerated movement of the target due to simultaneous blast loading.

Combined load bearing capacity of rigid piles embedded in a crossanisotropic clay deposit using 3D finite element lower bound

In this study,an iterative-based three-dimensional finite element lower bound in association with the second-order cone programming method is adopted to evaluate the limit load of a single pile embedded in cross-anisotropic soils under general loading condition.The lower bound solutions of the pile embedded in an anisotropic soil deposit can be found by formulating the element equilibrium,equilibrium of shear and normal stresses along discontinuities,boundary conditions,yield function,and optimizing the objective function through the second-order cone programming method in conjunction with an iterative-based update procedure.A general loading condition is considered to profile the expansion of the safe load in the vertical-horizontal-moment(V-H-M)space.The results of this study are compared and validated against three different cases including an isotropic lateral loading,anisotropic end bearing capacity,and a pile embedded in an isotropic soil deposit under general loading condition.A parametric study is conducted to evaluate the impact of different influencing factors.It was found that the effect of anisotropy on the variation of lateral limit load of a single pile is more pronounced than the corresponding vertical and bending moment limit loads,whereas the interface properties have more significant effects on the vertical and bending moment limit loads in comparison to the lateral limit load.

Reliability analysis of marine risers with narrow and long corrosion defects under combined loads

A marine riser,one of the most important components of offshore oil/gas transportation,needs to be designed to eliminate the risks caused by complex ocean environments,platform displacement and internal corrosion,etc.In this study,a new analytical-numerical assessment approach is proposed in order to quantitatively investigate the reliability of internally corroded risers under combined loads including axial tension and internal pressure.First,an analytical solution of the limit state function of intact risers under combined loads is obtained,which is further modified by the non-dimensional corrosion depth （d/ t） for the risers with a narrow and long corrosion defect.The relationship between d/t and limited internal pressure is obtained by finite element analysis and nonlinear regression.Through an advanced first-order reliability method （HL-RF） algorithm,reliability analysis is performed to obtain the failure probability,the reliability index and the sensitivity.These results are further verified by Monte-Carlo importance sampling.The proposed approach of reliability analysis provides an accurate and effective way to estimate the reliability of marine risers with narrow and long corrosion defects under combined loads.

Analytic elasticity solution of bi-modulus beams under combined loads

A unified stress function for bi-modulus beams is proposed based on its mechanic sense on the boundary of beams. Elasticity solutions of stress and displacement for bi-modulus beams under combined loads are derived. The example analysis shows that the maximum tensile stress using the same elastic modulus theory is underestimated if the tensile elastic modulus is larger than the compressive elastic modulus. Otherwise, the maximum compressive stress is underestimated. The maximum tensile stress using the material mechanics solution is underestimated when the tensile elastic modulus is larger than the compressive elastic modulus to a certain extent. The error of stress using the material mechanics theory decreases as the span-to-height ratio of beams increases, which is apparent when L/h ≤ 5. The error also varies with the distributed load patterns.

Elastoplastic solutions for single piles under combined vertical and lateral loads

为了改进单身者的设计和计算的可靠性，堆在下面联合了垂直、侧面的负担，答案基于路基反应方法，最终的土壤抵抗在被考虑被介绍，路基反应的系数被假定是一个常数。相应计算节目用 FORTRAN 语言被开发。在获得的答案和模型测试结果之间的比较被做显示出获得的答案的有效性。，计算结果显示有垂直、侧面的负担和上面的堆积长度的增加的最大的侧面的排水量和弯曲时刻增加磨擦了作为堆积僵硬，路基反应的系数和土壤增加的让步的排水量减少。堆积头条件控制堆积回答，这也被显示出，垂直负担可以引起不稳定性问题到堆积。一般来说，建议方法能被采用计算堆积偏转的大小的堆积回答独立人士。

General Analytical Shakedown Analysis of a Structure Subjected to Combined Loading with Constant and Cyclic Loads

The shakedown behavior of structures subjected to a combined loading of constant and cyclic loads has been well researched.For some specified problems,shakedown limit loads have been obtained.However,the general effect of combined loading on the structural shakedown has not yet been presented.The general analytic solution of the elastic shakedown limit load is thus derived for a structure subjected to combined loading.Polizzotto's extended static shakedown theorem for combined loading is applied.The stress field in equilibrium with the external constant load required in Polizzotto's extended theorem is constructed by subtracting the reference elastic stress field of the peak cyclic load from the elastic-plastic stress field of the combined constant load and peak cyclic load.The shakedown condition of the stress field is then derived according to the extended theorem.Through the analytical analysis of the shakedown condition,the structural shakedown behavior under combined loading is investigated.A general solution of the shakedown limit load is then derived,and the effects of the combined loading on the shakedown behavior are proposed.The obtained general analytical result is applied to a hollow tension specimen under constant tension and alternating torsion and a plate with a central hole under constant and cyclic tension.The results are consistent with the solutions reported in the literature.

Method for Calculating the Ultimate Strength of Pitting Corrosion Ship Structural Plates Under Combined Loads

In order to solve the problem of calculating the ultimate strength of marine plate under pitting corrosion,the plate taking from marine with pitting corrosion was studied. Based on the data of pitting corrosion recorded,the concept of pitting corrosion characteristic element matrix was proposed to describe the distribution and the forms of pitting. Moreover,the model of sensitivity calculation was established to analyse the sensitivity of pitting corrosion characteristic elements for the ultimate bearing capacity of ship structural plate. A new approach was proposed to calculate the ultimate strength of pitting damaged ship structural plate under combined loads based on the factor of rigidity reduction. Simultaneously this new approach was proven to be validated by finite element simulation. Finally,formula of ultimate strength of pitting damaged ship hull plate was established by series of numerical calculations based on the approach,and the reliability of the formula was validated as well.

Reinforcement Method of the Tubular Joints under Combined Loads Based on ANSYS Software

The jacket offshore platform structures working in the environment are subjected to various external conditions,such as wave loads,wind loads and corrosion of sea water.Therefore,the research on reinforcement of tubular joints has great practical value for the safety of offshore platforms.In this article,the finite element(FE)models of T-type tubular joint(T-joint)and K-type tubular joint(K-joint)are established by ANSYS software.Triangular rib reinforcement and collar plate reinforcement are used to reinforce the tubular joints.The reinforcement effects are assessed through the ultimate bearing capacity,and the influences of parameters of the rib and the collar plate on the ultimate capacity are analyzed.Besides,the effects of the two reinforcement methods are compared under the combined loads,and the results show that the reinforcement of the ribbed plate is more effective in resisting the deformation caused by bending moment,while the reinforcement of the collar plate is more effective to avoid the plastic damage caused by the axial pressure.

LARGE DEFLECTION PROBLEM OF CIRCULAR PLATES WITH VARIABLE THICKNESS UNDER THE ACTION OF COMBINED LOADS

By using the modified iteration method of large deflection theory of plates with variable thichness[1], we solve the problem of circular plates with variable thickness subjected to combined loads under the boundary conditions of the clamped edges and get comparatively more accurate second-order approximate analytical solution. If the results of this paper are degraded into the special cases, the results coinciding with those of papers [1,2] can be obtained. In this paper, the characteristic curves are plotted and some comparisons are made. The results of this paper are satisfactory.

Transformation Matrix for Combined Loads Applied to Thin-Walled Structures

This paper transforms combined loads, applied at an arbitrary point of a thin-walled open section beam, to the shear centre of the cross-section of the beam. Therein, a generalized transformation matrix for loads with respect to the shear centre is derived, this accounting for the bimoments that develop due to the way the combined loads are applied. This and the authors’ earlier paper (World Journal of Mechanics 2021, 11, 205-236) provide a full solution to the theory of thin-walled, open-section structures bearing combined loading. The earlier work identified arbitrary loading with the section’s area properties that are necessary to axial and shear stress calculations within the structure’s thin walls. In the previous paper attention is paid to the relevant axes of loading and to the transformations of loading required between axes for stress calculations arising from tension/compression, bending, torsion and shear. The derivation of the general transformation matrix applies to all types of loadings including, axial tensile and compression forces, transverse shear, longitudinal bending. One application, representing all these load cases, is given of a simple channel cantilever with an eccentrically located end load.

Fatigue Life of Slewing Bearings under Combined Radial,Axial and Tilting Moment Loads

A calculation method of fatigue life for slewing bearings under combined radial, axial and tilting moment loads was proposed. Single row four-point contact ball slewing bearing being used as a case, the statics model of the slewing bearing was established and a set of equilibrium equations were obtained. By solving the equilibrium equatioas, the rolling element loads were obtained and the equivalent rolling element loads were calculated further. By using the geometrical parameters of the bearing, the rating rolling element loads were calculated, and the fa- tigue life of the bearing was calculated by using the rating rolling element loads and the equivalent rolling element loads. A calculation example shows the feasibility of the proposed method.

Study on Failure Mechanism and Bearing Capacity of Three-Dimensional Rectangular Footing Subjected to Combined Loading

This paper presents two kinematic failure mechanisms of threc-dimensional rectangular footing resting on homogeneous undrained clay foundation under uniaxial vertical loading and uniaxial moment loading. The failure mechanism under vertical loading comprises a plane strain Prandti-type mechanism over the central part of the longer side, and the size of the mechanism gradually reduces at the ends of the longer side and over the shorter side as the corner of rectangular footing is being approached where the direction of soil motion remains normal to each corresponding side respectively. The failure mechanism under moment loading comprises a plane strain scoop sliding mechanism over the central part of the longer side, and the radius of scoop sliding mechanism increases linearly at the ends of the longer side. On the basis of the kinematic failure mechanisms mentioned above, the vertical ultimate bearing capacity and the ultimate bearing capacity against moment or moment ultimate bearing capacity are obtained by use of upper bound limit analysis theory. At the same time, numerical analysis results, Skempton＇ s results and Salgado et al. ＇s results are compared with this upper bound solution. It shows that the presented failure mechanisms and plastic limit analysis predictions are validated. In order to investigate the behaviors of undrained clay foundation beneath the rectangular footing subjected to the combined loadings, numerical analysis is adopted by virtue of the general-purpose FEM software ABAQUS, where the clay is assumed to obey the Mohr-Coulomb yielding criterion. The failure envelope and the ultimate bearing capacity are achieved by the numerical analysis results with the varying aspect ratios from length L to breadth B of the rectangular footing. The failure mechanisms of rectangular footing which are subjected to the combined vertical loading V and horizontal loading H （Vertical loading V and moment loading M, and horizontal loading H and moment loading M respectively are observed in the finite element analysis. ） is explained by use of the upper bound plasticity limit analysis theory. Finally, the reason of eccentricity of failure envelope in H-M loading space is given in this study, which can not be explained by use of the traditional ＇ swipe test＇.

Mechanical performance of rock bolts under combined load conditions

Rock bolts are subjected to different loading conditions along their lengths such as axial,bending,and/or shear forces,which can cause failure at lower loads than those considered for design purposes.The common existing methodologies do not consider the actual loading of the rock bolts and assume it is only pure axial or pure shear.This study was conducted to investigate the un-grouted rock bolt performance under combined load conditions.Two loading regimes were evaluated:the effect of initial shear displacement on axial load capacity and displacement,and the effect of axial displacement on the shear load capacity.The first regime was also conducted for shear with a gap,when there is a spacing between the shear interfaces.The results of this study showed that the rock bolt can resist higher axial loads than shear under pure or combined load conditions.Under combined load conditions,the rock bolt capacity decreased significantly for both regimes.However,when applying the shear load with a gap,the rock bolt load capacity was not affected significantly.Also,the total bar deformation was improved for shear and axial.The findings of this study show the need to improve the rock bolt design considering the complex loading conditions in situ with/without a gap.

Undrained Bearing Capacity of Spudcan Under Combined Loading

The bearing capacities of spudcan foundation under pure vertical （/1）, horizontal （H）, moment （M） loading and the combined loading are studied based on a series of three-dimensional finite element analysis. The effects of embedment ratio and soil non-homogeneity on the bearing capacity are investigated in detail. The capacities of spudcan under different pure loading are expressed in non-dimensional bearing capacity factors, which are compared with published results. Ultimate limit states under combined loading are presented by failure envelopes, which are expressed in terms of dimensionless and normalized form in three-dimensional load space. The comparison between the presented failure envelopes and available published numerical results reveals that the size and shape of failure envelopes are dependent on the embedment ratio and the non-homogeneity of the soil.

Failure Loci of Suction Caisson Foundations Under CombinedLoading Conditions

Suction caissons are widely used to support offshore fixed platforms in coastal areas. The loadings transferred to suction caissons include the eccentric lateral force induced by waves and self weight of the platform structure. However, under this kind of combined loading conditions, the failure mechanism of caissons with shallow embedment depths is quite different from conventional deep foundations or onshore shallow footings. The behaviour of caissons subjected to combined loadings may be described with the ＂failure locus＂ in force resultant spaces. Here the failure loci of smooth caissons are studied by use of finite dement approach, with the embedment ratio of caissons varying in the range of 0.25 - 1.0 and eccentricity ratio of horizontal loadiugs in 0 - 10. The platform settlement and tilt limits are involved into determination of failure loci, thus the platforms can avoid significant displacements for the combined loadings located inside the failure locus. Three families of loading paths are used to map out the locus. It is found that the shape of failure loci depends on 3 non-dimensional parameters, and the failure locus of a given caisson changes gradually from the elliptical curve to hooked curve with increasing shear strength of soil. The lateral capacity of short caissons may be enhanced by vertical forces, compared with the maximum lateral capacity of long caissons occurring at the vertical force being zero. The critical embedment ratios partitioning elliptical and hooked loci are proposed.

Variable-stiffness composite cylinder design under combined loadings by using the improved Kriging model

The large design freedom of variable-stiffness (VS) composite material presupposes its potential for wide engineering application. Previous research indicates that the design of VS cylindrical structures helps to increase the buckling load as compared to quasi-isotropic (QI) cylindrical structures. This paper focuses on the anti-buckling performance of VS cylindrical structures under combined loads and the efficient optimization design method. Two kinds of conditions, bending moment and internal pressure, and bending moment and torque are considered. Influences of the geometrical defects, ovality, on the cylinder's performances are also investigated. To increase the computational efficiency, an adaptive Kriging meta-model is proposed to approximate the structural response of the cylinders. In this improved Kriging model, a mixed updating rule is used in constructing the meta-model. A genetic algorithm (GA) is implemented in the optimization design. The optimal results show that the buckling load of VS cylinders in all cases is greatly increased as compared with a QI cylinder.

Study on Deformation Law of Circular Foundation Under Combined Loading

The foundations of some ocean engineering structures are built to withstand not only the vertical gravity load V, but also the horizontal load H induced by sea waves and current. The horizontal load includes the concentrated force load, the moment load M, and the torque load T termed also as combined loading. It is of academic and engineering significance to study the deformation law of submarine seabed due to combined loading. On the basis of the three-dimensional elastic mechanics solution of circular foundation, numerical methods are used to analyze the deformation law of submarine soil under circular foundation with six degrees of freedom. The finite element analysis results give the elastic deformation law of soil in three dimensional spaces, modify the theoretical elasticity solution, and presents nonlinear soil deformation mechanism under the circular foundation with six degrees of freedom.

Buckling analysis of shear deformable composite conical shells reinforced by CNTs subjected to combined loading on the two-parameter elastic foundation

The main objective of this study is to investigate the buckling analysis of CCSs reinforced by CNTs subjected to combined loading of hydrostatic pressure and axial compression resting on the twoparameter elastic foundation(T-P-EF).It is one of the first attempts to derive the governing equations of the CCSs reinforced with CNTs,based on a generalized first-order shear deformation shell theory(FSDST)which includes shell-foundation interaction.By adopting the extended mixing rule,the effective material properties of CCSs reinforced by CNTs with linear distributions are approximated by introducing some efficiency parameters.Three carbon nanotube distribution in the matrix,i.e.uniform distribution(U)and V and X-types linear distribution are taken into account.The stability equations are solved by using the Galerkin procedure to determine the combined buckling loads(CBLs)of the structure selected here.The numerical illustrations cover CBLs characteristics of CCSs reinforced by CNTs in the presence of the T-P-EF.Finally,a parametric study is carried out to study the influences of the foundation parameters,the volume fraction of carbon nanotubes and the types of reinforcement on the CBLs.

A HALF PLANE CRACK UNDER THREE-DIMENSIONAL COMBINED MODE IMPACT LOADING

The dynamic stress intensity factor history for a half plane crack in an otherwise unbounded elastic body, with the crack faces subjected to a traction distribution consisting of two pairs of suddenly-applied shear line loads is consid- ered. The analytic expression for the combined mode stress intensity factors as a function of time is obtained. The method of solution is based on the application of integral transforms and the Wiener-Hopf technique. Some features of the solutions are discussed and graphical numerical results are presented.

Mechanical responses of anchoring structure under triaxial cyclic loading

Dynamic load on anchoring structures(AS)within deep roadways can result in cumulative damage and failure.This study develops an experimental device designed to test AS under triaxial loads.The device enables the investigation of the mechanical response,failure mode,instability assessment criteria,and anchorage effect of AS subjected to combined cyclic dynamic-static triaxial stress paths.The results show that the peak bearing strength is positively correlated with the anchoring matrix strength,anchorage length,and edgewise compressive strength.The bearing capacity decreases significantly when the anchorage direction is severely inclined.The free face failure modes are typically transverse cracking,concave fracturing,V-shaped slipping and detachment,and spallation detachment.Besides,when the anchoring matrix strength and the anchorage length decrease while the edgewise compressive strength,loading rate,and anchorage inclination angle increase,the failure intensity rises.Instability is determined by a negative tangent modulus of the displacement-strength curve or the continued deformation increase against the general downward trend.Under cyclic loads,the driving force that breaks the rock mass along the normal vector and the rigidity of the AS are the two factors that determine roadway stability.Finally,a control measure for surrounding rock stability is proposed to reduce the internal driving force via a pressure relief method and improve the rigidity of the AS by full-length anchorage and grouting modification.