To compute the matching performance of diesel engine with variable geometry turboeharger(VGT), the formerly used program is improved through adjustment of turbine mass flow rate and efficiency characteristics. The c...To compute the matching performance of diesel engine with variable geometry turboeharger(VGT), the formerly used program is improved through adjustment of turbine mass flow rate and efficiency characteristics. The calculation result is applied to forecast the performance of J6110Z diesel engine with rotary-vaned VGT70, and to guide the improvement of engine fuel supply. The computed engine performance curve coincides with the experiment result well: the low-speed torque, fuel economy, exhaust temperature and boost pressure of the VGT engine are all improved.展开更多
Variable geometry truss manipulator (VGTM) has potential to work in the future space applications, of which a dynamic model is important to dynamic analysis and control of the system. In this paper, an approach is p...Variable geometry truss manipulator (VGTM) has potential to work in the future space applications, of which a dynamic model is important to dynamic analysis and control of the system. In this paper, an approach is presented to model the dynamic equations of a VGTM by independent variables, which consists of two double-octahedral truss units and a 3-revolute-prismatic-spherical (3-RPS) parallel manipulator. In this ap- proach, the kinematic recursive relations of two adjacent bodies and geometric constrains are used to deduce the kinematic equations of the VGTM, and Jourdain's velocity varia- tion principle is adopted to establish the dynamic equations of the system. The validity of the proposed dynamic model is verified by comparison of numerical simulations with the software ADAMS. Besides, an active controller for trajectory tracking of the system is designed by the computed torque method. The effectiveness of the controller is numer- ically proved.展开更多
Conventionally,the method to make up for the missing data of middle-shallow layer in the obstacle area is by variable geometry,for example,deviating physical points and adding sources and receivers.And the missing dat...Conventionally,the method to make up for the missing data of middle-shallow layer in the obstacle area is by variable geometry,for example,deviating physical points and adding sources and receivers.And the missing data of middle-shallow layer is evaluated according to the effective coverage of the target layer.Since the traditional method doesn't consider the actual seismic data,it is impossible to actually predict the gap of section and the imaging effect.The paper proposes the evaluation method of data-driven based variable geometry:Firstly,the obstacle avoidance design is realized according to the coordinate range and safe distance of the obstacle area;Secondly,the local similarity of each common image gather(CIG)is calculated,and the contribution of the sources and receivers to the target area is also calculated;Thirdly,according to the variable geometry design,choose the required trace to perform sorting and stacking according to the contribution of the sources and receivers in the CIG,the stack data volume of the whole work area is generated;finally,evaluate the missing data in the obstacle area by the extracted seismic stacked sections in different direction and guide the designer in the infilling plan.Meanwhile,for area with very low signal to noise ratio(SNR),the new method can be used to evaluate the imaging potential and guide the survey design.The new method has achieved very good effect in the production,and the analysis result is very consistent with the processed result of the actual seismic data.展开更多
A novel variable geometry flame-holder(VGF) based on V-gutter was presented.The structural characteristics of the flame holder were introduced.Experimental study on drag characteristics of the VGF on un-burning and bu...A novel variable geometry flame-holder(VGF) based on V-gutter was presented.The structural characteristics of the flame holder were introduced.Experimental study on drag characteristics of the VGF on un-burning and burning states was conducted in a rectangular combustion test rig.The influence of the change of gutter trailing edge width w on pressure recovery in different operating conditions was analyzed emphatically.Furthermore,drag characteristics in different trailing edge width variation modes were discussed.Results show that:(1) Narrowing w can observably raise the total pressure recovery σ but the highest σ is not obtained at minimum w.(2) The relationship of drag coefficient ψ and w in the un-burning conditions can be well expressed in a form of exponential equation(w/d>0.4).(3) Drag characteristics are not sensitive to the variation modes and speeds of w.(4) In the burning condition,σ decreases with the increasing of w basically and the course can be divided into three stages.The results and experimental data presented in this paper would enhance the phenomenological understanding of this type of VGF,and would contribute to the next experimental study and numerical calculus of this novel VGF.展开更多
A spatial motion mechanism was designed which could make all the nozzle vanes rotate a- round the center of ball with the same radius synchronously to realize control of the variable nozzle mixed-flow turbocharger (V...A spatial motion mechanism was designed which could make all the nozzle vanes rotate a- round the center of ball with the same radius synchronously to realize control of the variable nozzle mixed-flow turbocharger (VN-MT). The back and abdomen of the nozzle vane was designed as arc- shaped. A variable nozzle ring perfectly combined with the mixed-flow turbine was made available. The turbine geometric model of VN-MT was established through the computational fluid dynamics (CFD). Compared with nozzleless mixed-flow turbine, the flow range of variable nozzle mixed-flow turbine was broadened tremendously while the peak turbine efficiency point was lower slightly. Flow field analysis in turbine stage showed that the energy was larger and the blade load of rotor was lower than loss of the VN-MT under designed condition the nozzleless mixed-flow turbocharger.展开更多
Variable structure control (VSC) applied to atmospheric disturbance sup-pression is presented. The conditions are stipulated: the sliding mode existenee condi-tion, and invanance condition of atmospheric disturbanee i...Variable structure control (VSC) applied to atmospheric disturbance sup-pression is presented. The conditions are stipulated: the sliding mode existenee condi-tion, and invanance condition of atmospheric disturbanee in the variable structuresystem (VSS). A method of eigenstructure assignment technique for switching surfaeedesign is proposed. Based on different atmospheric disturbanee characteristics, such asrandom turbulence, discrete gust and wind shear, two kinds of control laws are derived that possess strong robustness. An example shows that this control approach isfeasible and effective.展开更多
Despite small workspace, parallel manipulators have some advantages over their serial counterparts in terms of higher speed, acceleration, rigidity, accuracy, manufacturing cost and payload. Accordingly, this type of ...Despite small workspace, parallel manipulators have some advantages over their serial counterparts in terms of higher speed, acceleration, rigidity, accuracy, manufacturing cost and payload. Accordingly, this type of manipulators can be used in many applications such as in high-speed machine tools, tuning machine for feeding, sensitive cutting, assembly and packaging. This paper presents a special type of planar parallel manipulator with three degrees of freedom. It is constructed as a variable geometry truss generally known planar Stewart platform. The reachable and orientation workspaces are obtained for this manipulator. The inverse kinematic analysis is solved for the trajectory tracking according to the redundancy and joint limit avoidance. Then, the dynamics model of the manipulator is established by using Virtual Work method. The simulations are performed to follow the given planar trajectories by using the dynamic equations of the variable geometry truss manipulator and computed force control method. In computed force control method, the feedback gain matrices for PD control are tuned with fixed matrices by trail end error and variable ones by means of optimization with genetic algorithm.展开更多
A turbocharged diesel engine model was built with the GT-Power software,and experimentally verified.Then two different control variables for the control of the variable geometry turbocharger(VGT)were described,and t...A turbocharged diesel engine model was built with the GT-Power software,and experimentally verified.Then two different control variables for the control of the variable geometry turbocharger(VGT)were described,and their distinct effects on engine performance,i.e.NOxand soot emissions and fuel consumption,were simulated and compared on the basis of this model.The results showed that NOxemissions decreased obviously with the increase of exhaust gas recirculation(EGR)rate at constant boost pressure condition,but soot emissions and fuel consumption considerably increased.It was a good way to reduce NOxemissions without increasing fuel consumption and soot emissions when VGT was controlled to maintain the excess oxygen ratio unchanged as EGR rate increases.展开更多
As a novel aero-engine concept,adaptive cycle aero-engines(ACEs) are attracting wide attention in the international aviation industry due to their potential superior task adaptability along a wide flight regime.Howe...As a novel aero-engine concept,adaptive cycle aero-engines(ACEs) are attracting wide attention in the international aviation industry due to their potential superior task adaptability along a wide flight regime.However,this superior task adaptability can only be demonstrated through proper combined engine control schedule design.It has resulted in an urgent need to investigate the effect of each variable geometry modulation on engine performance and stability.Thus,the aim of this paper is to predict and discuss the effect of each variable geometry modulation on the matching relationship between engine components as well as the overall engine performance at different operating modes,on the basis of a newly developed nonlinear component-based ACE performance model.Results show that at all four working modes,turning down the high pressure compressor variable stator vane,the low pressure turbine variable nozzle,the nozzle throat area,and turning up the core-driven fan stage variable stator vane,the high pressure turbine variable nozzle can increase the thrust at the expense of a higher high pressure turbine inlet total temperature.However,the influences of these adjustments on the trends of various engine components' working points and working lines as well as the ratio of the rotation speed difference are different from each other.The above results provide valuable guidance and advice for engine combined control schedule design.展开更多
基金the Ministerial Level Advanced Research Foundation (37256)
文摘To compute the matching performance of diesel engine with variable geometry turboeharger(VGT), the formerly used program is improved through adjustment of turbine mass flow rate and efficiency characteristics. The calculation result is applied to forecast the performance of J6110Z diesel engine with rotary-vaned VGT70, and to guide the improvement of engine fuel supply. The computed engine performance curve coincides with the experiment result well: the low-speed torque, fuel economy, exhaust temperature and boost pressure of the VGT engine are all improved.
基金Project supported by the National Natural Science Foundation of China(Nos.11132001,11272202,and 11472171)the Key Scientific Project of Shanghai Municipal Education Commission(No.14ZZ021)the Natural Science Foundation of Shanghai(No.14ZR1421000)
文摘Variable geometry truss manipulator (VGTM) has potential to work in the future space applications, of which a dynamic model is important to dynamic analysis and control of the system. In this paper, an approach is presented to model the dynamic equations of a VGTM by independent variables, which consists of two double-octahedral truss units and a 3-revolute-prismatic-spherical (3-RPS) parallel manipulator. In this ap- proach, the kinematic recursive relations of two adjacent bodies and geometric constrains are used to deduce the kinematic equations of the VGTM, and Jourdain's velocity varia- tion principle is adopted to establish the dynamic equations of the system. The validity of the proposed dynamic model is verified by comparison of numerical simulations with the software ADAMS. Besides, an active controller for trajectory tracking of the system is designed by the computed torque method. The effectiveness of the controller is numer- ically proved.
基金sponsored by the project of science and technology of CNPC(2021DJ3504)funded by Continuous research on CS (compressed sensing) seismic exploration technology (03-012021).
文摘Conventionally,the method to make up for the missing data of middle-shallow layer in the obstacle area is by variable geometry,for example,deviating physical points and adding sources and receivers.And the missing data of middle-shallow layer is evaluated according to the effective coverage of the target layer.Since the traditional method doesn't consider the actual seismic data,it is impossible to actually predict the gap of section and the imaging effect.The paper proposes the evaluation method of data-driven based variable geometry:Firstly,the obstacle avoidance design is realized according to the coordinate range and safe distance of the obstacle area;Secondly,the local similarity of each common image gather(CIG)is calculated,and the contribution of the sources and receivers to the target area is also calculated;Thirdly,according to the variable geometry design,choose the required trace to perform sorting and stacking according to the contribution of the sources and receivers in the CIG,the stack data volume of the whole work area is generated;finally,evaluate the missing data in the obstacle area by the extracted seismic stacked sections in different direction and guide the designer in the infilling plan.Meanwhile,for area with very low signal to noise ratio(SNR),the new method can be used to evaluate the imaging potential and guide the survey design.The new method has achieved very good effect in the production,and the analysis result is very consistent with the processed result of the actual seismic data.
文摘A novel variable geometry flame-holder(VGF) based on V-gutter was presented.The structural characteristics of the flame holder were introduced.Experimental study on drag characteristics of the VGF on un-burning and burning states was conducted in a rectangular combustion test rig.The influence of the change of gutter trailing edge width w on pressure recovery in different operating conditions was analyzed emphatically.Furthermore,drag characteristics in different trailing edge width variation modes were discussed.Results show that:(1) Narrowing w can observably raise the total pressure recovery σ but the highest σ is not obtained at minimum w.(2) The relationship of drag coefficient ψ and w in the un-burning conditions can be well expressed in a form of exponential equation(w/d>0.4).(3) Drag characteristics are not sensitive to the variation modes and speeds of w.(4) In the burning condition,σ decreases with the increasing of w basically and the course can be divided into three stages.The results and experimental data presented in this paper would enhance the phenomenological understanding of this type of VGF,and would contribute to the next experimental study and numerical calculus of this novel VGF.
基金Supported by the National Natural Science Foundation of China(51009003)
文摘A spatial motion mechanism was designed which could make all the nozzle vanes rotate a- round the center of ball with the same radius synchronously to realize control of the variable nozzle mixed-flow turbocharger (VN-MT). The back and abdomen of the nozzle vane was designed as arc- shaped. A variable nozzle ring perfectly combined with the mixed-flow turbine was made available. The turbine geometric model of VN-MT was established through the computational fluid dynamics (CFD). Compared with nozzleless mixed-flow turbine, the flow range of variable nozzle mixed-flow turbine was broadened tremendously while the peak turbine efficiency point was lower slightly. Flow field analysis in turbine stage showed that the energy was larger and the blade load of rotor was lower than loss of the VN-MT under designed condition the nozzleless mixed-flow turbocharger.
文摘Variable structure control (VSC) applied to atmospheric disturbance sup-pression is presented. The conditions are stipulated: the sliding mode existenee condi-tion, and invanance condition of atmospheric disturbanee in the variable structuresystem (VSS). A method of eigenstructure assignment technique for switching surfaeedesign is proposed. Based on different atmospheric disturbanee characteristics, such asrandom turbulence, discrete gust and wind shear, two kinds of control laws are derived that possess strong robustness. An example shows that this control approach isfeasible and effective.
文摘Despite small workspace, parallel manipulators have some advantages over their serial counterparts in terms of higher speed, acceleration, rigidity, accuracy, manufacturing cost and payload. Accordingly, this type of manipulators can be used in many applications such as in high-speed machine tools, tuning machine for feeding, sensitive cutting, assembly and packaging. This paper presents a special type of planar parallel manipulator with three degrees of freedom. It is constructed as a variable geometry truss generally known planar Stewart platform. The reachable and orientation workspaces are obtained for this manipulator. The inverse kinematic analysis is solved for the trajectory tracking according to the redundancy and joint limit avoidance. Then, the dynamics model of the manipulator is established by using Virtual Work method. The simulations are performed to follow the given planar trajectories by using the dynamic equations of the variable geometry truss manipulator and computed force control method. In computed force control method, the feedback gain matrices for PD control are tuned with fixed matrices by trail end error and variable ones by means of optimization with genetic algorithm.
基金Supported by Diesel Engine Development Program of MIIT(DEDP-1004)Natural Science Foundation of BIT(3030012211428)
文摘A turbocharged diesel engine model was built with the GT-Power software,and experimentally verified.Then two different control variables for the control of the variable geometry turbocharger(VGT)were described,and their distinct effects on engine performance,i.e.NOxand soot emissions and fuel consumption,were simulated and compared on the basis of this model.The results showed that NOxemissions decreased obviously with the increase of exhaust gas recirculation(EGR)rate at constant boost pressure condition,but soot emissions and fuel consumption considerably increased.It was a good way to reduce NOxemissions without increasing fuel consumption and soot emissions when VGT was controlled to maintain the excess oxygen ratio unchanged as EGR rate increases.
基金supported by the National Natural Science Foundation of China(No.51206005)Collaborative Innovation Center of Advanced Aero-Engine of China
文摘As a novel aero-engine concept,adaptive cycle aero-engines(ACEs) are attracting wide attention in the international aviation industry due to their potential superior task adaptability along a wide flight regime.However,this superior task adaptability can only be demonstrated through proper combined engine control schedule design.It has resulted in an urgent need to investigate the effect of each variable geometry modulation on engine performance and stability.Thus,the aim of this paper is to predict and discuss the effect of each variable geometry modulation on the matching relationship between engine components as well as the overall engine performance at different operating modes,on the basis of a newly developed nonlinear component-based ACE performance model.Results show that at all four working modes,turning down the high pressure compressor variable stator vane,the low pressure turbine variable nozzle,the nozzle throat area,and turning up the core-driven fan stage variable stator vane,the high pressure turbine variable nozzle can increase the thrust at the expense of a higher high pressure turbine inlet total temperature.However,the influences of these adjustments on the trends of various engine components' working points and working lines as well as the ratio of the rotation speed difference are different from each other.The above results provide valuable guidance and advice for engine combined control schedule design.