A new normalized least mean square(NLMS) adaptive filter is first derived from a cost function, which incorporates the conventional one of the NLMS with a minimum-disturbance(MD)constraint. A variable regularization f...A new normalized least mean square(NLMS) adaptive filter is first derived from a cost function, which incorporates the conventional one of the NLMS with a minimum-disturbance(MD)constraint. A variable regularization factor(RF) is then employed to control the contribution made by the MD constraint in the cost function. Analysis results show that the RF can be taken as a combination of the step size and regularization parameter in the conventional NLMS. This implies that these parameters can be jointly controlled by simply tuning the RF as the proposed algorithm does. It also demonstrates that the RF can accelerate the convergence rate of the proposed algorithm and its optimal value can be obtained by minimizing the squared noise-free posteriori error. A method for automatically determining the value of the RF is also presented, which is free of any prior knowledge of the noise. While simulation results verify the analytical ones, it is also illustrated that the performance of the proposed algorithm is superior to the state-of-art ones in both the steady-state misalignment and the convergence rate. A novel algorithm is proposed to solve some problems. Simulation results show the effectiveness of the proposed algorithm.展开更多
This paper proposes a robust adaptive filter based on the exponent sin cost to improve the capability against Gaussian or multiple types of non-Gaussian noises of the adaptive filtering algorithm when dealing with tim...This paper proposes a robust adaptive filter based on the exponent sin cost to improve the capability against Gaussian or multiple types of non-Gaussian noises of the adaptive filtering algorithm when dealing with time-varying/time-invariant linear systems function exponent sin(ExpSin).Then a variable step-size(VSS)-ExpSin algorithm is extended further.Besides,the stepsize,the convergence,and the steady-state performance of the proposed algorithm are validated experimentally.The Monte Carlo simulation results of linear system identification illustrate the principle and efficiency of this proposed adaptive filtering algorithm.Results suggest that the proposed adaptive filtering algorithm has superior performance when estimating the unknown linear systems under multiple-types measurement noises.展开更多
To solve the contradiction between convergence rate and steady-state error in least mean square (LMS) algorithm, basing on independence assumption, this paper proposes and proves the optimal step-size theorem from the...To solve the contradiction between convergence rate and steady-state error in least mean square (LMS) algorithm, basing on independence assumption, this paper proposes and proves the optimal step-size theorem from the view of minimizing mean squared error (MSE). The theorem reveals the one-to-one mapping between the optimal step-size and MSE. Following the theorem, optimal variable step-size LMS (OVS-LMS) model, describing the theoretical bound of the convergence rate of LMS algorithm, is constructed. Then we discuss the selection of initial optimal step-size and updating of optimal step-size at the time of unknown system changing. At last an optimal step-size LMS algorithm is proposed and tested in various environments. Simulation results show the proposed algorithm is very close to the theoretical bound.展开更多
Implicit-explicit (IMEX) linear multistep methods are popular techniques for solving partial differential equations (PDEs) with terms of different types. While fixed timestep versions of such schemes have been dev...Implicit-explicit (IMEX) linear multistep methods are popular techniques for solving partial differential equations (PDEs) with terms of different types. While fixed timestep versions of such schemes have been developed and studied, implicit-explicit schemes also naturally arise in general situations where the temporal smoothness of the solution changes. In this paper we consider easily implementable variable step-size implicit-explicit (VSIMEX) linear multistep methods for time-dependent PDEs. Families of order-p, pstep VSIMEX schemes are constructed and analyzed, where p ranges from 1 to 4. The corresponding schemes are simple to implement and have the property that they reduce to the classical IMEX schemes whenever constant time step-sizes are imposed. The methods are validated on the Burgers' equation. These results demonstrate that by varying the time step-size, VSIMEX methods can outperform their fixed time step counterparts while still maintaining good numerical behavior.展开更多
A new variable step-size algorithm for a second-order lattice form structure adaptive infinite impulse response (IIR) notch filter to detection and estimation frequency of sinusoids in Gaussian noises is proposed. U...A new variable step-size algorithm for a second-order lattice form structure adaptive infinite impulse response (IIR) notch filter to detection and estimation frequency of sinusoids in Gaussian noises is proposed. Utilizing least square kurtosis of output signals as a cost function, the new gradient-based algorithm to update frequency of the adaptive IIR notch filter and the new variable step-size algorithm are given. The computer simulation results show that the proposed algorithm has better ability in suppressing colored Gaussian noises and better accuracy in estimating parameters at low SNR than previous algorithms.展开更多
Compared with vertical and horizontal wells, the solution and computation of transient pressure responses of slanted wells are more complex. Vertical and horizontal wells are both simplified cases of slanted wells at ...Compared with vertical and horizontal wells, the solution and computation of transient pressure responses of slanted wells are more complex. Vertical and horizontal wells are both simplified cases of slanted wells at particular inclination, so the model for slanted wells is more general and more complex than other models for vertical and horizontal wells. Many authors have studied unsteady-state flow of fluids in slanted wells and various solutions have been proposed. However, until now, few of the published results pertain to the computational efficiency. Whether in the time domain or in the Laplace domain, the computation of integration of complex functions is necessary in obtaining pressure responses of slanted wells, while the computation of the integration is complex and time-consuming. To obtain a perfect type curve the computation time is unacceptable even with an aid of high-speed computers. The purpose of this paper is to present an efficient algorithm to compute transient pressure distributions caused by slanted wells in reservoirs. Based on rigorous derivation, the transient pressure solution for slanted wells of any inclination angle is presented. Assuming an infinite-conductivity wellbore, the location of the equivalent-pressure point is determined. More importantly, according to the characteristics of the integrand in a transient pressure solution for slanted wells, the whole integral interval is partitioned into several small integral intervals, and then the method of variable substitution and the variable step-size piecewise numerical integration are employed. The amount of computation is significantly reduced and the computational efficiency is greatly improved. The algorithm proposed in this paper thoroughly solved the difficulty in the efficient and high-speed computation of transient pressure distribution of slanted wells with any inclination angle.展开更多
This paper presents the development of a dynamic Active Noise Control(ANC)algorithm aimed towards redu-cingthe broadbandnoiseinside the helmet earcups ofafighter aircraftpilot helmet.The dynamicANC involves a Variable ...This paper presents the development of a dynamic Active Noise Control(ANC)algorithm aimed towards redu-cingthe broadbandnoiseinside the helmet earcups ofafighter aircraftpilot helmet.The dynamicANC involves a Variable Step-Size Griffiths(VSSG)FxLMS algorithm to attenuate noise entering directly through helmet,a LMS based adaptive noise canceller to attenuate noise entering through the pilot microphone,and energy detectors for failure protection and optimized battery power usage.The algorithms are implemented on Texas Instruments’TMS320C6748 processor and are tested in a helmet ANC experimental setup.展开更多
To improve the security and reliability of a distribution network, several issues, such as influences of operation con-strains, real-time load margin calculation, and online security level evaluation, are with great s...To improve the security and reliability of a distribution network, several issues, such as influences of operation con-strains, real-time load margin calculation, and online security level evaluation, are with great significance. In this pa-per, a mathematical model for load capability online assessment of a distribution network is established, and a repeti-tive power flow calculation algorithm is proposed to solve the problem as well. With assessment on three levels: the entire distribution network, a sub-area of the network and a load bus, the security level of current operation mode and load transfer capability during outage are thus obtained. The results can provide guidelines for prevention control, as well as restoration control. Simulation results show that the method is simple, fast and can be applied to distribution networks belonged to any voltage level while taking into account all of the operation constraints.展开更多
A variable step-size parameter is usually used to accelerate the convergence speed of a blind adaptive equalizer with N1 + N2 -1 coefficients where N1 and N2 are odd values. In this paper we show that improved equaliz...A variable step-size parameter is usually used to accelerate the convergence speed of a blind adaptive equalizer with N1 + N2 -1 coefficients where N1 and N2 are odd values. In this paper we show that improved equalization performance is achieved when using two blind adaptive equalizers connected in series where the first and second blind adaptive equalizer have N1 and N2 coefficients respectively compared with the case where a single blind adaptive equalizer is applied with N1 + N2 -1 coefficients. It should be pointed out that the same algorithm (cost function) is used for updating the filter taps for the different equalizers and that a fixed step-size parameter is used. Simulation results show that for the low signal to noise ratio (SNR) environment and for the case where the convergence speed is slow due to the channel characteristics, the new method has a faster convergence speed with a factor of approximately two while leaving the system with approximately the same or lower residual intersymbol interference (ISI).展开更多
基金supported by the National Natural Science Foundation of China(61571131 11604055)
文摘A new normalized least mean square(NLMS) adaptive filter is first derived from a cost function, which incorporates the conventional one of the NLMS with a minimum-disturbance(MD)constraint. A variable regularization factor(RF) is then employed to control the contribution made by the MD constraint in the cost function. Analysis results show that the RF can be taken as a combination of the step size and regularization parameter in the conventional NLMS. This implies that these parameters can be jointly controlled by simply tuning the RF as the proposed algorithm does. It also demonstrates that the RF can accelerate the convergence rate of the proposed algorithm and its optimal value can be obtained by minimizing the squared noise-free posteriori error. A method for automatically determining the value of the RF is also presented, which is free of any prior knowledge of the noise. While simulation results verify the analytical ones, it is also illustrated that the performance of the proposed algorithm is superior to the state-of-art ones in both the steady-state misalignment and the convergence rate. A novel algorithm is proposed to solve some problems. Simulation results show the effectiveness of the proposed algorithm.
文摘This paper proposes a robust adaptive filter based on the exponent sin cost to improve the capability against Gaussian or multiple types of non-Gaussian noises of the adaptive filtering algorithm when dealing with time-varying/time-invariant linear systems function exponent sin(ExpSin).Then a variable step-size(VSS)-ExpSin algorithm is extended further.Besides,the stepsize,the convergence,and the steady-state performance of the proposed algorithm are validated experimentally.The Monte Carlo simulation results of linear system identification illustrate the principle and efficiency of this proposed adaptive filtering algorithm.Results suggest that the proposed adaptive filtering algorithm has superior performance when estimating the unknown linear systems under multiple-types measurement noises.
基金This work was supported in part by the National Fundamental Research Program(Grant No.G1998030406)the National Natural Science Foundation of China(Grant No.69972020)by the State Key Lab on Microwave and Digital Communications,Department of Electronics Engineering,Tsinghua University.
文摘To solve the contradiction between convergence rate and steady-state error in least mean square (LMS) algorithm, basing on independence assumption, this paper proposes and proves the optimal step-size theorem from the view of minimizing mean squared error (MSE). The theorem reveals the one-to-one mapping between the optimal step-size and MSE. Following the theorem, optimal variable step-size LMS (OVS-LMS) model, describing the theoretical bound of the convergence rate of LMS algorithm, is constructed. Then we discuss the selection of initial optimal step-size and updating of optimal step-size at the time of unknown system changing. At last an optimal step-size LMS algorithm is proposed and tested in various environments. Simulation results show the proposed algorithm is very close to the theoretical bound.
基金supported by an NSERC Canada Postgraduate Scholarshipsupported by a grant from NSERC Canada
文摘Implicit-explicit (IMEX) linear multistep methods are popular techniques for solving partial differential equations (PDEs) with terms of different types. While fixed timestep versions of such schemes have been developed and studied, implicit-explicit schemes also naturally arise in general situations where the temporal smoothness of the solution changes. In this paper we consider easily implementable variable step-size implicit-explicit (VSIMEX) linear multistep methods for time-dependent PDEs. Families of order-p, pstep VSIMEX schemes are constructed and analyzed, where p ranges from 1 to 4. The corresponding schemes are simple to implement and have the property that they reduce to the classical IMEX schemes whenever constant time step-sizes are imposed. The methods are validated on the Burgers' equation. These results demonstrate that by varying the time step-size, VSIMEX methods can outperform their fixed time step counterparts while still maintaining good numerical behavior.
文摘A new variable step-size algorithm for a second-order lattice form structure adaptive infinite impulse response (IIR) notch filter to detection and estimation frequency of sinusoids in Gaussian noises is proposed. Utilizing least square kurtosis of output signals as a cost function, the new gradient-based algorithm to update frequency of the adaptive IIR notch filter and the new variable step-size algorithm are given. The computer simulation results show that the proposed algorithm has better ability in suppressing colored Gaussian noises and better accuracy in estimating parameters at low SNR than previous algorithms.
基金financial support from the special fund of China’s central government for the development of local colleges and universities―the project of national first-level discipline in Oil and Gas Engineering, the National Science Fund for Distinguished Young Scholars of China (Grant No. 51125019)the National Program on Key fundamental Research Project (973 Program, Grant No. 2011CB201005)
文摘Compared with vertical and horizontal wells, the solution and computation of transient pressure responses of slanted wells are more complex. Vertical and horizontal wells are both simplified cases of slanted wells at particular inclination, so the model for slanted wells is more general and more complex than other models for vertical and horizontal wells. Many authors have studied unsteady-state flow of fluids in slanted wells and various solutions have been proposed. However, until now, few of the published results pertain to the computational efficiency. Whether in the time domain or in the Laplace domain, the computation of integration of complex functions is necessary in obtaining pressure responses of slanted wells, while the computation of the integration is complex and time-consuming. To obtain a perfect type curve the computation time is unacceptable even with an aid of high-speed computers. The purpose of this paper is to present an efficient algorithm to compute transient pressure distributions caused by slanted wells in reservoirs. Based on rigorous derivation, the transient pressure solution for slanted wells of any inclination angle is presented. Assuming an infinite-conductivity wellbore, the location of the equivalent-pressure point is determined. More importantly, according to the characteristics of the integrand in a transient pressure solution for slanted wells, the whole integral interval is partitioned into several small integral intervals, and then the method of variable substitution and the variable step-size piecewise numerical integration are employed. The amount of computation is significantly reduced and the computational efficiency is greatly improved. The algorithm proposed in this paper thoroughly solved the difficulty in the efficient and high-speed computation of transient pressure distribution of slanted wells with any inclination angle.
基金funded by National Programme on Micro and Smart Systems(NPMaSS),Aeronautical Development Agency(ADA),Bangalore.Grant No.ADA/NPMASS159/2015,S.Veena。
文摘This paper presents the development of a dynamic Active Noise Control(ANC)algorithm aimed towards redu-cingthe broadbandnoiseinside the helmet earcups ofafighter aircraftpilot helmet.The dynamicANC involves a Variable Step-Size Griffiths(VSSG)FxLMS algorithm to attenuate noise entering directly through helmet,a LMS based adaptive noise canceller to attenuate noise entering through the pilot microphone,and energy detectors for failure protection and optimized battery power usage.The algorithms are implemented on Texas Instruments’TMS320C6748 processor and are tested in a helmet ANC experimental setup.
文摘To improve the security and reliability of a distribution network, several issues, such as influences of operation con-strains, real-time load margin calculation, and online security level evaluation, are with great significance. In this pa-per, a mathematical model for load capability online assessment of a distribution network is established, and a repeti-tive power flow calculation algorithm is proposed to solve the problem as well. With assessment on three levels: the entire distribution network, a sub-area of the network and a load bus, the security level of current operation mode and load transfer capability during outage are thus obtained. The results can provide guidelines for prevention control, as well as restoration control. Simulation results show that the method is simple, fast and can be applied to distribution networks belonged to any voltage level while taking into account all of the operation constraints.
文摘A variable step-size parameter is usually used to accelerate the convergence speed of a blind adaptive equalizer with N1 + N2 -1 coefficients where N1 and N2 are odd values. In this paper we show that improved equalization performance is achieved when using two blind adaptive equalizers connected in series where the first and second blind adaptive equalizer have N1 and N2 coefficients respectively compared with the case where a single blind adaptive equalizer is applied with N1 + N2 -1 coefficients. It should be pointed out that the same algorithm (cost function) is used for updating the filter taps for the different equalizers and that a fixed step-size parameter is used. Simulation results show that for the low signal to noise ratio (SNR) environment and for the case where the convergence speed is slow due to the channel characteristics, the new method has a faster convergence speed with a factor of approximately two while leaving the system with approximately the same or lower residual intersymbol interference (ISI).