The performance of the vehicle dynamics stability control system(DSC) is dominated by the accurate estimation of tire forces in real-time.The characteristics of tire forces are determined by tire dynamic states and ...The performance of the vehicle dynamics stability control system(DSC) is dominated by the accurate estimation of tire forces in real-time.The characteristics of tire forces are determined by tire dynamic states and parameters,which vary in an obviously large scope along with different working conditions.Currently,there have been many methods based on the nonlinear observer to estimate the tire force and dynamic parameters,but they were only used in off-line analysis because of the computation complexity and the dynamics differences of four tires in the steering maneuver conditions were not considered properly.This paper develops a novel algorithm to observe tire parameters in real-time controller for DSC.The algorithm is based on the sensor-fusion technology with the signals of DSC sensors,and the tire parameters are estimated during a set of maneuver courses.The calibrated tire parameters in the control cycle are treated as the elementary states for vehicle dynamics observation,in which the errors between the calculated and the measured vehicle dynamics are used as the correcting factors for the tire parameter observing process.The test process with a given acceleration following a straight line is used to validate the estimation method of the longitudinal stiffness;while the test process with a given steering angle is used to validate the estimated value of the cornering stiffness.The ground test result shows that the proposed algorithm can estimate the tire stiffness accurately with an acceptable computation cost for real-time controller only using DSC sensor signal.The proposed algorithm can be an efficient algorithm for estimating the tire dynamic parameters in vehicle dynamics stability control system,and can be used to improve the robustness of the DSC controller.展开更多
This paper presents a coordinating and stabilizing control law for a group of underwater vehicles with unstable dynamics. The coordinating law is derived from a potential that only depends on the relative configuratio...This paper presents a coordinating and stabilizing control law for a group of underwater vehicles with unstable dynamics. The coordinating law is derived from a potential that only depends on the relative configuration of the underwater vehicles. Being coordinated,the group behaves like one mechanical system with symmetry,and we focus on stabilizing a family of coordinated motions,called relative equilibria. The stabilizing law is derived using energy shaping to stabilize the relative equilibria which involve each vehicle translating along its longest(unstable) axis without spinning,while maintaining a relative configuration within the group. The proposed control law is physically motivated and avoids the linearization or cancellation of nonlinearities.展开更多
From the analysis of experiment data of the multi-axle vehicle chassis searching process, it is less accurate to predict multi-axle vehicle dynamic characteristic with simplified two-axle vehicle model. So it is impor...From the analysis of experiment data of the multi-axle vehicle chassis searching process, it is less accurate to predict multi-axle vehicle dynamic characteristic with simplified two-axle vehicle model. So it is important to find out a more effective modeling method in the study of multi-vehicle stability. In the development of heat transfer fluid(HTF) six-axle vehicle, a whole vehicle multi-body dynamic model is built through collaborate flowchart using Teamcenter Engineering, UG NX3 and MSC.Adams. The modeling method of connected hydragas spring suspension is validated by running test results. Based on this whole vehicle model, a kinematical analysis of suspension is implemented to achieve optimized suspension geometry parameters according to the stable requirement. Then, different handling simulations are carried out with regard to various tire characteristics, driving con- figurations, and equipments. According to the evaluation of whole vehicle handling characteristic, some design rules are summarized to improve the stability of multi-axle vehicle.展开更多
The suspension coil spring is one of the most important components in a vehicle suspension system. Its primary function is to absorb the vibrational shocks that are occasioned by irregular road surface to provide the ...The suspension coil spring is one of the most important components in a vehicle suspension system. Its primary function is to absorb the vibrational shocks that are occasioned by irregular road surface to provide the vehicle with stability and ride comfort. The main objective of this study is to design a suspension coil spring made of structural steel for light duty vehicles with the aim of weight and cost reduction. This study was motivated by the government of Ghana’s actions to industrialise the automotive sector of the country through government policies and programs. The study made use of high carbon steel and low carbon steel as the control materials and structural steel as the implementing material. This was done to determine the suitability of structural steel for vehicle suspension coil spring. The study analysed parameters such as total deformation, equivalent Von Mises stress, maximum shear stress, and safety factor in the static structural analysis. The fatigue analysis also analysed parameters such as fatigue life and fatigue alternating stress. The results of the study revealed that the suspension spring made of structural steel has superior properties against all the parameters set for this study apart from deformation. The two control materials that are known for suspension coil spring design and manufacture have better properties to withstand deformation than the implementing material.展开更多
Combined with the characteristics of the distributed-drive electric vehicle and direct yaw moment control,a double-layer structure direct yaw moment controller is designed.The upper additional yaw moment controller is...Combined with the characteristics of the distributed-drive electric vehicle and direct yaw moment control,a double-layer structure direct yaw moment controller is designed.The upper additional yaw moment controller is constructed based on model predictive control.Aiming at minimizing the utilization rate of tire adhesion and constrained by the working characteristics of motor system and brake system,a quadratic programming active set was designed to optimize the distribution of additional yaw moments.The road surface adhesion coefficient has a great impact on the reliability of direct yaw moment control,for which joint observer of vehicle state parameters and road surface parameters is designed by using unscented Kalman filter algorithm,which correlates vehicle state observer and road surface parameter observer to form closed-loop feedback correction.The results show that compared to the“feedforward+feedback”control,the vehicle’s error of yaw rate and sideslip angle by the model predictive control is smaller,which can improve the vehicle stability effectively.In addition,according to the results of the docking road simulation test,the joint observer of vehicle state and road surface parameters can improve the adaptability of the vehicle stability controller to the road conditions with variable adhesion coefficients.展开更多
A method of extracting and detecting vehicle stability state characteristics based on entropy is proposed.The vehicle’s longitudinal and lateral dynamics models are established for complex driving and maneuver condit...A method of extracting and detecting vehicle stability state characteristics based on entropy is proposed.The vehicle’s longitudinal and lateral dynamics models are established for complex driving and maneuver conditions.The corresponding state observer is designed by adopting the moving horizon estimation algorithm,which realizes the observation of the vehicle stability state considering the global state information.Meanwhile,the Shannon entropy is modified to approximate entropy,and the approximate entropy value of the observed vehicle state is calculated.Furthermore,the optimal controller is designed to further validate the reliability of the entropy value as the reference of control system.Simulation results demonstrate that this method can quickly detect the instability state of the system during the process of vehicle driving,which provides a reference for risk prediction and active control.展开更多
A novel real-time predictive control strategy is proposed for path following(PF)and vehicle stability of autonomous electric vehicles under extreme drive conditions.The investigated vehicle configuration is a distribu...A novel real-time predictive control strategy is proposed for path following(PF)and vehicle stability of autonomous electric vehicles under extreme drive conditions.The investigated vehicle configuration is a distributed drive electric vehicle,which allows to independently control the torques of each in-wheel motor(IWM)for superior stability,but bringing control com-plexities.The control-oriented model is established by the Magic Formula tire function and the single-track vehicle model.For PF and direct yaw moment control,the nonlinear model predictive control(NMPC)strategy is developed to minimize PF tracking error and stabilize vehicle,outputting front tires’lateral force and external yaw moment.To mitigate the calcu-lation burdens,the continuation/general minimal residual algorithm is proposed for real-time optimization in NMPC.The relaxation function method is adopted to handle the inequality constraints.To prevent vehicle instability and improve steering capacity,the lateral velocity differential of the vehicle is considered in phase plane analysis,and the novel stable bounds of lateral forces are developed and online applied in the proposed NMPC controller.Additionally,the Lyapunov-based constraint is proposed to guarantee the closed-loop stability for the PF issue,and sufficient conditions regarding recursive feasibility and closed-loop stability are provided analytically.The target lateral force is transformed as front steering angle command by the inversive tire model,and the external yaw moment and total traction torque are distributed as the torque commands of IWMs by optimization.The validations prove the effectiveness of the proposed strategy in improved steering capacity,desirable PF effects,vehicle stabilization,and real-time applicability.展开更多
Air-breathing hypersonic vehicles (HSVs) are typically characterized by interactions of elasticity, propulsion and rigid-body flight dynamics, which may result in intractable aeroservoelastic problem. When canard is...Air-breathing hypersonic vehicles (HSVs) are typically characterized by interactions of elasticity, propulsion and rigid-body flight dynamics, which may result in intractable aeroservoelastic problem. When canard is added, this problem would be even intensified by the introduction of low-frequency canard pivot mode. This paper concerns how the aeroservoelastic stability of a canard-configured HSV is affected by the pivot stiffnesses of all-moveable horizontal tail (HT) and canard. A wing/pivot system model is developed by considering the pivot torsional flexibility, fuselage vibration, and control input. The governing equations of the aeroservoelastic system are established by combining the equations of rigid-body motion, elastic fuselage model, wing/pivot system models and actuator dynamics. An unsteady aerodynamic model is developed by steady Shock-Expansion theory with an unsteady correction using local piston theory. A baseline controller is given to provide approximate inflight characteristics of rigid-body modes. The vehicle is trimmed for equilibrium state, around which the linearized equations are derived for stability analysis. A comparative study of damping ratios, closed-loop poles and responses are conducted with varying controller gains and pivot stiffnesses. Available bandwidth for control design is discussed and feasible region for pivot stiffnesses of HT and canard is given.展开更多
Due to flexible drive-by-wire technology,vehicle stability control can improve handling and lateral stability under extreme conditions.However,this technology can also increase the probability of random transmission d...Due to flexible drive-by-wire technology,vehicle stability control can improve handling and lateral stability under extreme conditions.However,this technology can also increase the probability of random transmission delay.This paper proposes a nonlinear model predictive control(NMPC)strategy to improve vehicle stability and compensate for the random time delay.First,by combining the nonlinear dynamic characteristics and driver behavior,we obtain a stable region of the yaw rate and the sideslip angle under complex driving conditions.Second,an NMPC controller is designed to track the reference values in the identified stable region to improve the handling and lateral stability.Finally,the actuator receives the optimized control sequence and compensates for the random time delay of the transmission channel.CarSim/Simulink simulation and hardware-in-the-loop experiment results show that the proposed controller with dynamic boundary conditions can better track the expected value of the yaw rate and suppress the sideslip angle under low adhesion road conditions.展开更多
An autonomous approach and landing(A&L) guidance law is presented in this paper for landing an unpowered reusable launch vehicle(RLV) at the designated runway touchdown. Considering the full nonlinear point-mass ...An autonomous approach and landing(A&L) guidance law is presented in this paper for landing an unpowered reusable launch vehicle(RLV) at the designated runway touchdown. Considering the full nonlinear point-mass dynamics, a guidance scheme is developed in threedimensional space. In order to guarantee a successful A&L movement, the multiple sliding surfaces guidance(MSSG) technique is applied to derive the closed-loop guidance law, which stems from higher order sliding mode control theory and has advantage in the finite time reaching property.The global stability of the proposed guidance approach is proved by the Lyapunov-based method.The designed guidance law can generate new trajectories on-line without any specific requirement on off-line analysis except for the information on the boundary conditions of the A&L phase and instantaneous states of the RLV. Therefore, the designed guidance law is flexible enough to target different touchdown points on the runway and is capable of dealing with large initial condition errors resulted from the previous flight phase. Finally, simulation results show the effectiveness of the proposed guidance law in different scenarios.展开更多
基金supported by National Natural Science Foundation of China (Grant No.50905092)
文摘The performance of the vehicle dynamics stability control system(DSC) is dominated by the accurate estimation of tire forces in real-time.The characteristics of tire forces are determined by tire dynamic states and parameters,which vary in an obviously large scope along with different working conditions.Currently,there have been many methods based on the nonlinear observer to estimate the tire force and dynamic parameters,but they were only used in off-line analysis because of the computation complexity and the dynamics differences of four tires in the steering maneuver conditions were not considered properly.This paper develops a novel algorithm to observe tire parameters in real-time controller for DSC.The algorithm is based on the sensor-fusion technology with the signals of DSC sensors,and the tire parameters are estimated during a set of maneuver courses.The calibrated tire parameters in the control cycle are treated as the elementary states for vehicle dynamics observation,in which the errors between the calculated and the measured vehicle dynamics are used as the correcting factors for the tire parameter observing process.The test process with a given acceleration following a straight line is used to validate the estimation method of the longitudinal stiffness;while the test process with a given steering angle is used to validate the estimated value of the cornering stiffness.The ground test result shows that the proposed algorithm can estimate the tire stiffness accurately with an acceptable computation cost for real-time controller only using DSC sensor signal.The proposed algorithm can be an efficient algorithm for estimating the tire dynamic parameters in vehicle dynamics stability control system,and can be used to improve the robustness of the DSC controller.
基金supported by the National Natural Science Foundation of China (11072002, 10832006)
文摘This paper presents a coordinating and stabilizing control law for a group of underwater vehicles with unstable dynamics. The coordinating law is derived from a potential that only depends on the relative configuration of the underwater vehicles. Being coordinated,the group behaves like one mechanical system with symmetry,and we focus on stabilizing a family of coordinated motions,called relative equilibria. The stabilizing law is derived using energy shaping to stabilize the relative equilibria which involve each vehicle translating along its longest(unstable) axis without spinning,while maintaining a relative configuration within the group. The proposed control law is physically motivated and avoids the linearization or cancellation of nonlinearities.
文摘From the analysis of experiment data of the multi-axle vehicle chassis searching process, it is less accurate to predict multi-axle vehicle dynamic characteristic with simplified two-axle vehicle model. So it is important to find out a more effective modeling method in the study of multi-vehicle stability. In the development of heat transfer fluid(HTF) six-axle vehicle, a whole vehicle multi-body dynamic model is built through collaborate flowchart using Teamcenter Engineering, UG NX3 and MSC.Adams. The modeling method of connected hydragas spring suspension is validated by running test results. Based on this whole vehicle model, a kinematical analysis of suspension is implemented to achieve optimized suspension geometry parameters according to the stable requirement. Then, different handling simulations are carried out with regard to various tire characteristics, driving con- figurations, and equipments. According to the evaluation of whole vehicle handling characteristic, some design rules are summarized to improve the stability of multi-axle vehicle.
文摘The suspension coil spring is one of the most important components in a vehicle suspension system. Its primary function is to absorb the vibrational shocks that are occasioned by irregular road surface to provide the vehicle with stability and ride comfort. The main objective of this study is to design a suspension coil spring made of structural steel for light duty vehicles with the aim of weight and cost reduction. This study was motivated by the government of Ghana’s actions to industrialise the automotive sector of the country through government policies and programs. The study made use of high carbon steel and low carbon steel as the control materials and structural steel as the implementing material. This was done to determine the suitability of structural steel for vehicle suspension coil spring. The study analysed parameters such as total deformation, equivalent Von Mises stress, maximum shear stress, and safety factor in the static structural analysis. The fatigue analysis also analysed parameters such as fatigue life and fatigue alternating stress. The results of the study revealed that the suspension spring made of structural steel has superior properties against all the parameters set for this study apart from deformation. The two control materials that are known for suspension coil spring design and manufacture have better properties to withstand deformation than the implementing material.
基金funded by Youth Program of National Natural Science Foundation of China(52002034)National Key R&D Program of China(2018YFB1600701)+2 种基金Key Research and Development Program of Shaanxi(2020ZDLGY16-01,2019ZDLGY15-02)Natural Science Basic Research Program of Shaanxi(2020JQ-381)Fundamental Research Funds for the Central Universities,CHD(300102220113).
文摘Combined with the characteristics of the distributed-drive electric vehicle and direct yaw moment control,a double-layer structure direct yaw moment controller is designed.The upper additional yaw moment controller is constructed based on model predictive control.Aiming at minimizing the utilization rate of tire adhesion and constrained by the working characteristics of motor system and brake system,a quadratic programming active set was designed to optimize the distribution of additional yaw moments.The road surface adhesion coefficient has a great impact on the reliability of direct yaw moment control,for which joint observer of vehicle state parameters and road surface parameters is designed by using unscented Kalman filter algorithm,which correlates vehicle state observer and road surface parameter observer to form closed-loop feedback correction.The results show that compared to the“feedforward+feedback”control,the vehicle’s error of yaw rate and sideslip angle by the model predictive control is smaller,which can improve the vehicle stability effectively.In addition,according to the results of the docking road simulation test,the joint observer of vehicle state and road surface parameters can improve the adaptability of the vehicle stability controller to the road conditions with variable adhesion coefficients.
基金Supported by Beijing Institute of Technology Research Fund Program for Young Scholars(3030011181911)。
文摘A method of extracting and detecting vehicle stability state characteristics based on entropy is proposed.The vehicle’s longitudinal and lateral dynamics models are established for complex driving and maneuver conditions.The corresponding state observer is designed by adopting the moving horizon estimation algorithm,which realizes the observation of the vehicle stability state considering the global state information.Meanwhile,the Shannon entropy is modified to approximate entropy,and the approximate entropy value of the observed vehicle state is calculated.Furthermore,the optimal controller is designed to further validate the reliability of the entropy value as the reference of control system.Simulation results demonstrate that this method can quickly detect the instability state of the system during the process of vehicle driving,which provides a reference for risk prediction and active control.
基金supported by the Natural Science Foundation of Beijing(Grant No.3212013)by the National Natural Science Foundation of China(Grant No.51805030)in part by the National Natural Science Foundation of China(Grant No.51775039).
文摘A novel real-time predictive control strategy is proposed for path following(PF)and vehicle stability of autonomous electric vehicles under extreme drive conditions.The investigated vehicle configuration is a distributed drive electric vehicle,which allows to independently control the torques of each in-wheel motor(IWM)for superior stability,but bringing control com-plexities.The control-oriented model is established by the Magic Formula tire function and the single-track vehicle model.For PF and direct yaw moment control,the nonlinear model predictive control(NMPC)strategy is developed to minimize PF tracking error and stabilize vehicle,outputting front tires’lateral force and external yaw moment.To mitigate the calcu-lation burdens,the continuation/general minimal residual algorithm is proposed for real-time optimization in NMPC.The relaxation function method is adopted to handle the inequality constraints.To prevent vehicle instability and improve steering capacity,the lateral velocity differential of the vehicle is considered in phase plane analysis,and the novel stable bounds of lateral forces are developed and online applied in the proposed NMPC controller.Additionally,the Lyapunov-based constraint is proposed to guarantee the closed-loop stability for the PF issue,and sufficient conditions regarding recursive feasibility and closed-loop stability are provided analytically.The target lateral force is transformed as front steering angle command by the inversive tire model,and the external yaw moment and total traction torque are distributed as the torque commands of IWMs by optimization.The validations prove the effectiveness of the proposed strategy in improved steering capacity,desirable PF effects,vehicle stabilization,and real-time applicability.
基金co-supported by the National Natural Science Foundation of China(Nos.90916006,91116019 and 91216102)
文摘Air-breathing hypersonic vehicles (HSVs) are typically characterized by interactions of elasticity, propulsion and rigid-body flight dynamics, which may result in intractable aeroservoelastic problem. When canard is added, this problem would be even intensified by the introduction of low-frequency canard pivot mode. This paper concerns how the aeroservoelastic stability of a canard-configured HSV is affected by the pivot stiffnesses of all-moveable horizontal tail (HT) and canard. A wing/pivot system model is developed by considering the pivot torsional flexibility, fuselage vibration, and control input. The governing equations of the aeroservoelastic system are established by combining the equations of rigid-body motion, elastic fuselage model, wing/pivot system models and actuator dynamics. An unsteady aerodynamic model is developed by steady Shock-Expansion theory with an unsteady correction using local piston theory. A baseline controller is given to provide approximate inflight characteristics of rigid-body modes. The vehicle is trimmed for equilibrium state, around which the linearized equations are derived for stability analysis. A comparative study of damping ratios, closed-loop poles and responses are conducted with varying controller gains and pivot stiffnesses. Available bandwidth for control design is discussed and feasible region for pivot stiffnesses of HT and canard is given.
基金the National Natural Science Foundation of China(Grants No.62073152,61790564 and Grant U1964202)in part by the Graduate Innovation Fund of Jilin University(Grant No.101832020CX174).
文摘Due to flexible drive-by-wire technology,vehicle stability control can improve handling and lateral stability under extreme conditions.However,this technology can also increase the probability of random transmission delay.This paper proposes a nonlinear model predictive control(NMPC)strategy to improve vehicle stability and compensate for the random time delay.First,by combining the nonlinear dynamic characteristics and driver behavior,we obtain a stable region of the yaw rate and the sideslip angle under complex driving conditions.Second,an NMPC controller is designed to track the reference values in the identified stable region to improve the handling and lateral stability.Finally,the actuator receives the optimized control sequence and compensates for the random time delay of the transmission channel.CarSim/Simulink simulation and hardware-in-the-loop experiment results show that the proposed controller with dynamic boundary conditions can better track the expected value of the yaw rate and suppress the sideslip angle under low adhesion road conditions.
基金co-supported by the National Natural Science Foundation of China (Nos. 51407011, 11372034, 11572035)
文摘An autonomous approach and landing(A&L) guidance law is presented in this paper for landing an unpowered reusable launch vehicle(RLV) at the designated runway touchdown. Considering the full nonlinear point-mass dynamics, a guidance scheme is developed in threedimensional space. In order to guarantee a successful A&L movement, the multiple sliding surfaces guidance(MSSG) technique is applied to derive the closed-loop guidance law, which stems from higher order sliding mode control theory and has advantage in the finite time reaching property.The global stability of the proposed guidance approach is proved by the Lyapunov-based method.The designed guidance law can generate new trajectories on-line without any specific requirement on off-line analysis except for the information on the boundary conditions of the A&L phase and instantaneous states of the RLV. Therefore, the designed guidance law is flexible enough to target different touchdown points on the runway and is capable of dealing with large initial condition errors resulted from the previous flight phase. Finally, simulation results show the effectiveness of the proposed guidance law in different scenarios.