Mechanical properties and energy evolutions of burst-prone coal samples with holes and fillings

During the mining process of impact-prone coal seams,drilling pressure relief can reduce the impact propensity of the coal seam,but it also reduces the integrity and strength of the coal mass at the side of the roadway.Therefore,studying the mechanical properties and energy evolution rules of coal samples containing holes and filled structures has certain practical significance for achieving coordinated control of coal mine rockburst disasters and the stability of roadway surrounding rocks.To achieve this aim,seven types of burst-prone coal samples were prepared and subject to uniaxial compression experiments with the aid of a TAW-3000 electro-hydraulic servo testing machine.Besides,the stress–strain curves,acoustic emission signals,DIC strain fields and other data were collected during the experiments.Furthermore,the failure modes and energy evolutions of samples with varying drilled hole sizes and filling materials were analyzed.The results show that the indexes related to burst propensity of the drilled coal samples decline to some extent compared with those of the intact one,and the decline is positively corelated to the diameter of the drilled hole.After hole filling,the strain concentration degree around the drilled hole is lowered to a certain degree,and polyurethane filling has a more remarkable effect than cement filling.Meanwhile,hole filling can enhance the strength and deformation resistance of coal.Hole drilling can accelerate the release of accumulated elastic strain energy,turning the acoustic emission events from low-frequency and high-energy ones to high-frequency and low-energy ones,whereas hole filling can reduce the intensity of energy release.The experimental results and theoretical derivation demonstrate that hole filling promotes coal deformability and strength mainly by weakening stress concentration surrounding the drilled holes.Moreover,the fillings can achieve a better filling effect if their elastic modulus and Poisson’s ratio are closer to those of the coal body.

Treatment of Synovial Cysts in Relation to the Tibial Tunnel of Anterior Cruciate Ligament Grafts by Filling the Tunnel with Acrylic Cement

Introduction: Synovial cyst of the tibial tunnel in connection with anterior cruciate ligament (ACL) reconstruction is a rare but particularly troublesome complication. Medical treatment is often doomed to failure, and surgical treatment usually consists of excising the cyst and filling the tunnel with bone. The aim of this study was to evaluate the results of filling the tunnel with acrylic cement. Hypothesis: Filling the tibial bone tunnel with acrylic cement should eliminate communication between the joint cavity and the pre-tibial surface and prevent cyst recurrence. Patients and Methods: This retrospective series is composed of 13 patients, 9 men and 4 women, mean age 48.5 years (31 to 64) operated on between 2011 and 2019 for an intra- and extraosseous synovial cyst consecutive to the tibial tunnel of an ACL graft. Between 1983 and 2016, 12 of the patients had had a bone graft without bone block fixation (DI-DT or Mac Intosh) and one patient, a bone-bone transplant (KJ). The cyst was of variable size, located on the anteromedial aspect of the proximal end of the tibia, and often painful, warranting consultation. At the time of the initial operation, 9 patients had undergone meniscectomies (6 medial, 2 lateral, 1 double). In 7 knees, there were 7 cartilage lesions in the femorotibial and/or patellofemoral compartments (one stage 1 lesion, 2 stage 2 lesions, 4 stage 3 lesions, and no stage 4 lesions). Only 2 knees had neither cartilage nor meniscus lesions. After curettage of the bone tunnel /− removal of the non-resorbed or PEEK interference screw, the tunnel was filled with acrylic cement /− reinforced with a ligament staple to prevent expulsion. All patients underwent regular follow-up consultations until recovery. Results: At a maximum follow-up of 8 years, only 1 cyst recurred, representing a 7.69% failure rate. It was reoperated with another technique, which involved filling the tibial bone tunnel with bone graft taken from a half-bank head. After recovery, the cyst healed definitively. All patients were able to return to their previous activity within 15 days of surgery. Conclusion: Filling the tibial tunnel with acrylic cement reinforced /− with a ligament staple is a reliable and rapid solution for the treatment of intra- and extra-articular synovial cysts in relation to the tibial tunnel of ACL grafts.

Grain-filling strategies of wheat of contrasting grain sizes under various planting patterns and irrigation levels

In a study comparing grain filling and yield in a large-and a small-grain-size wheat cultivar under two planting patterns and two irrigation regimes,plastic-covered ridge and furrow planting with sprinkler irrigation increased grain filling and yield in both cultivars.The largest contributors to grain yield were an extended active grain-filling period in Shuangda 1 and an increased mean grain-filling rate in XN538.

Effects of water and nitrogen rate on grain-filling characteristics under high-low seedbed cultivation in winter wheat

A high-efficiency mode of high-low seedbed cultivation(HLSC)has been listed as the main agricultural technology to increase land utilization ratio and grain yield in Shandong Province,China.However,limited information is available on the optimized water and nitrogen management for yield formation,especially the grain-filling process,under HLSC mode.A three-year field experiment with four nitrogen rates and three irrigation rates of HLSC was conducted to reveal the response of grain-filling parameters,grain weight percentage of spike weight(GPS),spike moisture content(SMC),and winter wheat yield to water and nitrogen rates.The four nitrogen rates were N1(360 kg ha^(-1) pure N),N2(300 kg ha^(-1) pure N),N3(240 kg ha^(-1) pure N),and N4(180 kg ha^(-1) pure N),respectively,and the three irrigation quotas were W1(120 mm),W2(90 mm),and W3(60 mm),respectively.Results showed that the determinate growth function generally performed well in simulating the temporal dynamics of grain weight(0.989<R^(2)<0.999,where R2 is the determination coefficient).The occurrence time of maximum filling rate(T_(max))and active grain-filling period(AGP)increased with the increase in the water or nitrogen rate,whereas the average grain-filling rate(G_(mean))had a decreasing trend.The final 1,000-grain weight(FTGW)increased and then decreased with the increase in the nitrogen rates and increased with the increase in the irrigation rates.The GPS and SMC had a highly significant quadratic polynomial relationship with grain weight and days after anthesis.Nitrogen,irrigation,and year significantly affected the T_(max),AGP,G_(mean),and FTGW.Particularly,the AGP and FTGW were insignificantly different between high seedbed(HLSC-H)and low seedbed(HLSC-L)across the water and nitrogen levels.Moreover,the moderate water and nitrogen supply was more beneficial for grain yield,as well as for spike number and grain number per hectare.The principal component analysis indicated that combining 240-300 kg N ha^(-1) and 90^(-1)20 mm irrigation quota could improve grain-filling efficiency and yield for the HLSC-cultivated winter wheat.

Heterogeneous information phase space reconstruction and stability prediction of filling body–surrounding rock combination

Traditional research believes that the filling body can effectively control stress concentration while ignoring the problems of unknown stability and the complex and changeable stress distribution of the filling body–surrounding rock combination under high-stress conditions.Current monitoring data processing methods cannot fully consider the complexity of monitoring objects,the diversity of monitoring methods,and the dynamics of monitoring data.To solve this problem,this paper proposes a phase space reconstruction and stability prediction method to process heterogeneous information of backfill–surrounding rock combinations.The three-dimensional monitoring system of a large-area filling body–surrounding rock combination in Longshou Mine was constructed by using drilling stress,multipoint displacement meter,and inclinometer.Varied information,such as the stress and displacement of the filling body–surrounding rock combination,was continuously obtained.Combined with the average mutual information method and the false nearest neighbor point method,the phase space of the heterogeneous information of the filling body–surrounding rock combination was then constructed.In this paper,the distance between the phase point and its nearest point was used as the index evaluation distance to evaluate the stability of the filling body–surrounding rock combination.The evaluated distances(ED)revealed a high sensitivity to the stability of the filling body–surrounding rock combination.The new method was then applied to calculate the time series of historically ED for 12 measuring points located at Longshou Mine.The moments of mutation in these time series were at least 3 months ahead of the roadway return dates.In the ED prediction experiments,the autoregressive integrated moving average model showed a higher prediction accuracy than the deep learning models(long short-term memory and Transformer).Furthermore,the root-mean-square error distribution of the prediction results peaked at 0.26,thus outperforming the no-prediction method in 70%of the cases.

Analysis of the Effectiveness of Modified Non- Traumatic Filling Technology in the Treatment of Pediatric Dental Caries

Objective:To analyze the effectiveness of modified non-traumatic filling technology in the treatment of pediatric dental caries.Methods:Ninety-seven children with dental caries who were treated in our hospital(Panyu Maternal and Child Care Service Center of Guangzhou)from January 2022 to December 2023 were selected and randomly divided into two groups,with 48 cases in the experimental group and 49 in the control group.The experimental group was treated with modified non-traumatic filling techniques,while the control group was treated with conventional filling techniques.Observation indicators such as the total effectiveness of the treatment,incidence of adverse events,treatment compliance,and pain scores were analyzed after the intervention.Result:After intervention,the total effectiveness of the treatment in the experimental group was higher than that in the control group(P<0.05).The incidence of adverse events in the experimental group was lower than that of the control group(P<0.05).The treatment compliance of patients in the experimental group was higher than that in the control group(P<0.05).The pain score of the experimental group was lower than that of the control group(P<0.05).Conclusion:The application of modified non-traumatic filling technology in the treatment of pediatric dental caries showed good therapeutic outcomes.After the intervention,the child’s symptoms were significantly alleviated,the incidence of adverse events such as filling material falling off was reduced,their compliance was improved,and the pain was relieved.This procedure is worth to be promoted for clinical application.

Tuning Active Metal Atomic Spacing by Filling of Light Atoms and Resulting Reversed Hydrogen Adsorption-Distance Relationship for Efficient Catalysis

Precisely tuning the spacing of the active centers on the atomic scale is of great significance to improve the catalytic activity and deepen the understanding of the catalytic mechanism,but still remains a challenge.Here,we develop a strategy to dilute catalytically active metal interatomic spacing(d_(M-M))with light atoms and discover the unusual adsorption patterns.For example,by elevating the content of boron as interstitial atoms,the atomic spacing of osmium(d_(Os-Os))gradually increases from 2.73 to 2.96?.More importantly,we find that,with the increase in dOs-Os,the hydrogen adsorption-distance relationship is reversed via downshifting d-band states,which breaks the traditional cognition,thereby optimizing the H adsorption and H_2O dissociation on the electrode surface during the catalytic process;this finally leads to a nearly linear increase in hydrogen evolution reaction activity.Namely,the maximum dOs-Os of 2.96?presents the optimal HER activity(8 mV@10 mA cm^(-2))in alkaline media as well as suppressed O adsorption and thus promoted stability.It is believed that this novel atomic-level distance modulation strategy of catalytic sites and the reversed hydrogen adsorption-distance relationship can shew new insights for optimal design of highly efficient catalysts.

FGW1, a protein containing DUF630 and DUF632 domains, regulates grain size and filling in Oryza sativa L.

Grain filling influences grain size and quality in cereal crops. The molecular mechanisms that regulate grain endosperm development remain elusive. In this study, we characterized a filling-defective and grain width mutant, fgw1, whose mutation increased rice seed width mainly via cell division and expansion in grains. Sucrose contents were higher but starch contents lower in the fgw1 mutant during the grainfilling stage, resulting in inferior endosperm of opaque, white appearance with loosely packed starch granules. Map-based cloning revealed that FGW1 encoded a protein containing DUF630/DUF632domains, localized in the plasma membrane with preferential expression in the panicle. RNA interference in FGW1 resulted in increased grain width and weight, whereas overexpression of FGW1 led to slightly narrower kernels and better grain filling. In a yeast two-hybrid assay, FGW1 interacted directly with the 14–3–3 protein GF14f, bimolecular fluorescence complementation verified that the site of interaction was the membrane, and the mutated FGW1 protein failed to interact with GF14f. The expression of GF14f was down-regulated in fgw1, and the activities of AGPase, StSase, and SuSase in the endosperm of fgw1increased similarly to those of a reported GF14f-RNAi. Transcriptome analysis indicated that FGW1 also regulates cellular processes and carbohydrate metabolism. Thus, FGW1 regulated grain formation via the GF14f pathway.

Effects of mechanical vibration on filling and solidification behavior, microstructure and performance of Al/Mg bimetal by lost foam compound casting

Al/Mg bimetal was prepared by lost foam solid-liquid compound casting,and the effects of mechanical vibration on the filling and solidification behavior,microstructure and performance of the bimetal were investigated.Results show that the mechanical vibration has a remarkable influence on the filling and solidification processes.It is found that after mechanical vibration,the filling rate increases and the filling rate at different times is more uniform than that without vibration.In addition,the mechanical vibration also increases the wettability between liquid AZ91D and A356 inlays.The mechanical vibration reduces the horizontal and vertical temperature gradient of the casting and makes the temperature distribution of the whole casting more uniform.Compared to the Al/Mg bimetal without vibration,the shear strength is improved by 39.76%after the mechanical vibration is applied,due to the decrease of the inclusions and Al_(12)Mg_(17) dendrites,and the refinement and uniform distribution of the Mg_(2)Si particles in the interface of the Al/Mg bimetal.

Raw Gangue Filling Mining under Construction —A Case Study in China

In order to recover the strip pillar coal resources, reduce the amount of gangue mountain and realize remediation of the goaf environment in the old mining area, the raw gangue filling mining technology was proposed. According to the previous practical experience, the feasibility of the implementation of raw gangue filling mining technology in the coal-pressed area was analyzed. Through the filling gangue compaction test, the deformation under different loading stages was obtained. Further, a reasonable prediction of the deformation beyond the experimental limited loading load was made based on the experimental results. Through the deformation source analysis of the whole process of gangue filling, the key factors for controlling deformation before, during, and after filling were determined. Additionally, the proportion of deformation during different stages was quantified. Considering the protection of surface buildings, mining fullness of the working face and mining technology, the production parameters of 1209 and 1210 filling working faces were preliminarily determined. Through numerical simulation, the rationality of mining scheme was verified. Based on the practice of 1209 working face and the key factors to control the deformation of gangue filling, the mining system and process in 1210 working face were optimized. According to the measured surface rock movement, raw gangue filling mining technology can meet the requirements of surface building protection level. Especially, this paper provides a method to quantitatively calculate the equivalent mining height (EMH) of raw gangue filling and its mining deformation, which has reference significance for old mining areas.

Depth Similarity Enhanced Image Summarization Algorithm for Hole-Filling in Depth Image-Based Rendering

In free viewpoint video(FVV)and 3DTV,the depth image-based rendering method has been put forward for rendering virtual view video based on multi-view video plus depth(MVD) format.However,the projection with slightly different perspective turns the covered background regions into hole regions in the rendered video.This paper presents a depth enhanced image summarization generation model for the hole-filling via exploiting the texture fidelity and the geometry consistency between the hole and the remaining nearby regions.The texture fidelity and the geometry consistency are enhanced by drawing texture details and pixel-wise depth information into the energy cost of similarity measure correspondingly.The proposed approach offers significant improvement in terms of 0.2dB PSNR gain,0.06 SSIM gain and subjective quality enhancement for the hole-filling images in virtual viewpoint video.

Vibration Reduction by a Partitioned Dynamic Vibration Absorber with Acoustic Black Hole Features

Vibration quality is a vital indicator for assessing the progress of modern equipment.The dynamic vibration absorber(DVA)based on the acoustic black hole(ABH)feature is a new passive control method that manipulates waves.It offers efficient energy focalization and broad-spectrum vibration suppression,making it highly promising for applications in large equipment such as aircraft,trains,and ships.Despite previous advancements in ABH-DVA development,certain challenges remain,particularly in ensuring effective coupling with host structures during control.To address these issues,this study proposes a partitioned ABH-featured dynamic vibration absorber(PABH-DVA)with partitions in the radial direction of the disc.By employing a plate as the host structure,simulations and experiments were conducted,demonstrating that the PABH-DVA outperforms the original symmetric ABH-DVA in terms of damping performance.The study also calculated and compared the coupling coefficients of the two ABH-DVAs to uncover the mechanism behind the enhanced damping.Simulation results revealed that the PABH-DVA exhibits more coupled modes,occasionally with lower coupling coefficients than the symmetric ABH-DVA.The influence of frequency ratio and modal mass was further analyzed to explain the reasons behind the PABH-DVA's superior damping performance.Additionally,the study discussed the impact of the number of slits and their orientation.This research further explains the coupling mechanism between the ABH-DVA and the controlled structure,and provides new ideas for the further application of ABH in engineering.

Algorithm of Detecting and Filling Small Holes in Triangular Mesh Surface

In some scattered point cloud triangular mesh restoration algorithm, small triangular mesh holes problem will often affect the quality of the model. For small holes at the details, this paper propose a method for identifying and extracting hollow edge,and use a triangle growth way based on boundary edge angle to fill the empty void. First, according the relationship of the point, side and face of the triangle mesh model to identify the hole, then extracting the holes boundary edge and classifying it. Finally, using a triangle growth method based on holes boundary edge angle to fill each small holes separated from the boundary. Compared with other algorithm of filling holes, this method is high efficiency for small holes of smooth surface,and itimprovesthe quality of the triangular mesh model.

Effects of Heat Stress during Seed Filling Stage on Brassica napus Seed Oil Accumulation and Chlorophyll Fluorescence Characteristics

As global temperature rise,the threat of heat stress to rapeseed production is becoming more obvious.Exploring the response characteristics of two important biological pathways,oil accumulation and photosynthesis,to heat stress during B.napus seed filling is helpful in the genetic improvement of heat-tolerant rapeseed.The effects of heat stress on seed oil accumulation and chlorophyll fluorescence characteristics of 29 B.napus germplasms with different oil content and environmental sensitivity,including 6 rapeseed varieties which exhibited environmentsensitive/insensitive and with high,medium or low oil content,were tested by whole plant heat stress or the in vitro silique culture system.Both assay exhibited similar trend on oil content of the rapeseed germplasms.The heat effect on the chlorophyll fluorescence kinetic parameters F_(v)/F_(m),ETR and Y(Ⅱ)were also consistent.Heat stress significantly decreased oil content,although there was abundant genetic variation on heat tolerance among the genotypes.Correlation analysis showed that the decrease rate of F_(v)/F_(m) of silique heat-stressed B.napus developing seed was positive correlative to the decrease rate of mature seed oil content of the whole plant heat-stressed rapeseed(R=0.9214,P-value<0.01).Overall,the results indicated that heat stress inhibited oil accumulation and photosynthesis in B.napus developing seed.The decrease rate of chlorophyll fluorescence parameter F_(v)/F_(m) of heat-stressed developing seed could be used as the index of heat tolerant rapeseed identification.Further,two heat insensitive rapeseed varieties with high oil content were identified.

Hydromassage of macular hole edges for large and persistent full-thickness macular holes

●AIM:To introduce the macular hole(MH)hydromassage technique as a potentially beneficial approach for the treatment of large or persistent MH.●METHODS:This retrospective observational case series comprised 16 consecutive patients(17 eyes)diagnosed with MH.Inclusion criteria involved a hole aperture diameter larger than 600μm or the presence of an unclosed MH larger than 600μm following the previous vitrectomy.Standard MH repair procedures were administered in all cases,involving the manipulation and aspiration of the hole margin through the application of water flow with a soft-tip flute needle.A comprehensive assessment was conducted for each case before and after surgery,and optical coherence tomography(OCT)images were captured at every follow-up point.●RESULTS:The mean preoperative aperture diameter was 747±156μm(range 611-1180μm),with a mean base diameter of 1390±435μm(range 578-2220μm).Following surgery,all cases achieved complete anatomical closure of MH,with 13 cases(76.5%)exhibiting type 1 closure and 4 cases(23.5%)demonstrating type 2 closure.No significant differences were observed in the preoperative OCT variables between the two closure types.Eyes with type 1 closure showed a significantly improved visual acuity(0.70±0.10,range 0.50-0.80)compared to those with type 2 closure(0.90±0.12,range 0.80-1.00,P=0.014).●CONCLUSION:The MH hydromassage technique demonstrates promising results,achieving acceptable closure rates in cases of large or persistent MH.This technique may serve as an effective adjunctive maneuver during challenging MH surgery.

Development of Machine Vision-Based Algorithm for Counting and Discriminating Filled and Unfilled Paddy Rice in Overlapping Mode

In this study, a new method based on image processing was presented to count and discriminate paddy rice, even when they overlapped. This method was performed in three steps. In the first step, using a reference image that excludes any overlapping paddy rice, the average area, standard deviation, and a threshold value for paddy rice were determined.

How is a black hole created from nothing?

Using the synchronous coordinates,the creation of a Schwarzschild black hole immersed in a de Sitter spacetime can be viewed as a coherent creation of a collection of timelike geodesics.The previously supposed conical singularities do not exist at the horizons of the constrained instanton.Instead,the unavoidable irregularity is presented as a nonvanishing second fundamental form elsewhere at the quantum transition 3-surface.The same arguments can be applied to charged,topological,or higher dimensional black hole cases.

Study of the spatial growth of stimulated Brillouin scattering in a gas-filled hohlraum via detecting the driven ion acoustic wave

In an experiment performed on the Shenguang-III prototype laser facility, collective Thomson scattering (TS) is used to study the spatialgrowth of stimulated Brillouin scattering (SBS) in a gas-filled hohlraum by detecting the SBS-driven ion acoustic wave. High-quality timeresolved SBS and TS spectra are obtained simultaneously in the experiment, and these are analyzed by a steady-state code based on theray-tracing model. The analysis indicates that ion–ion collisions may play an important role in suppressing SBS growth in the Au plasma;as aresult, the SBS excited in the filled gas region is dominant. In the early phase of the laser pulse, SBS originates primarily from the high-densityplasma at the edges of the interaction beam channel, which is piled up by the heating of the interaction beam. Throughout the duration of thelaser pulse, the presence of the TS probe beam might mitigate SBS by perturbing the density distribution around the region overlapping withthe interaction beam.

Radiopaque FeMnN-Mo composite drawn filled tubing wires for braided absorbable neurovascular devices

Flow diverter devices are small stents used to divert blood flow away from aneurysms in the brain,stagnating flow and inducing intra-aneurysmal thrombosis which in time will prevent aneurysm rupture.Current devices are formed from thin(~25μm)wires which will remain in place long after the aneurysm has been mitigated.As their continued presence could lead to secondary complications,an absorbable flow diverter which dissolves into the body after aneurysm occlusion is desirable.The absorbable metals investigated to date struggle to achieve the necessary combination of strength,elasticity,corrosion rate,fragmentation resistance,radiopacity,and biocompatibility.This work proposes and investigates a new composite wire concept combining absorbable iron alloy(FeMnN)shells with one or more pure molybdenum(Mo)cores.Various wire configurations are produced and drawn to 25–250μm wires.Tensile testing revealed high and tunable mechanical properties on par with existing flow diverter materials.In vitro degradation testing of 100μm wire in DMEM to 7 days indicated progressive corrosion and cracking of the FeMnN shell but not of the Mo,confirming the cathodic protection of the Mo by the FeMnN and thus mitigation of premature fragmentation risk.In vivo implantation and subsequentμCT of the same wires in mouse aortas to 6 months showed meaningful corrosion had begun in the FeMnN shell but not yet in the Mo filament cores.In total,these results indicate that these composites may offer an ideal combination of properties for absorbable flow diverters.

Sensitivity Analysis of Injection Characteristic to Structural Parameters of GDI Injector Nozzle Hole

The nozzle inner-flow characteristic of the“spray G”injector was studied by the computational fluid dynamics(CFD)simulation,and the sensitivity of cycle fuel mass to the conicity and entrance radius of the nozzle hole were analyzed.Results show that the inner conicity of nozzle hole inhibits the development of cavitation phenomena,and increases the injection rate.While the outer conicity of nozzle hole promotes the diffusion of cavita-tion,leading to reductions of the liquid volume fraction of the nozzle outlet and the local flow resistance of the nozzle hole.The sensitivity of cycle fuel mass to inner-cone nozzle hole is stronger than that of the outer-cone noz-zle,especially at the smaller hole conicity.The increase of injection pressure enhances the sensitivity of the injection characteristics to the nozzle hole structure,in which inner-cone nozzle has higher sensitivity coefficient than the outer-cone nozzle hole.However,the increase of injection pressure aggravates the offset of liquid jet to the nozzle axis of the outer-cone nozzle hole.With the increase of the inner conicity of nozzle,the sensitivity of the injection characteristics to the entrance radius of the hole decreases.With the increase of the outer conicity of nozzle hole,the sensitivity of the injection characteristics to the entrance radius of the hole increases.