Ambient vibration testing and updating of the finite element model of a simply supported beam bridge

An ambient vibration test on a concrete bridge constructed in 1971 and calibration of its finite element model are presented.The bridge is characterized by a system of post-tensioned and simply supported beams.The dynamic characteristics of the bridge,i.e.natural frequencies,mode shapes and damping ratios were computed from the ambient vibration tests by using the Eigensystem Realization Algorithm(ERA).Then,these characteristics were used to update the finite element model of the bridge by formulating an optimization problem and then using Genetic Algorithms(GA)to solve it.From the results of the ambient vibration test of this type of bridge,it is concluded that two-dimensional mode shapes exist:in the longitudinal and transverse;and these experimentally obtained dynamic characteristics were also achieved in the analytical model through updating.The application of GAs as optimization techniques showed great versatility to optimize any number and type of variables in the model.

Fatigue behavior of aluminum stiffened plate subjected to random vibration loading

Vibration tests were carried out on three types of stiffened aluminum plates with fully clamped boundaries under random base excitation. During the test, the response of the specimens was monitored using strain gauges. Based on the strain history, the accumulation of fatigue damage of the stiffened plates was estimated by means of the rainflow cycle counting technique and the Miner linear damage accumulation model in the time domain. Utilizing the change of natural frequencies, a nonlinear model was fitted for predicting the fatigue damage of plate and then the foregone failure criterion of 5% reduction in natural frequency is improved. The influence of section and spacing of the stiffeners on the vibration fatigue behavior of the aluminum plate was investigated. The results show that the fatigue life of aluminum plate increases with adding either T or L section riveted stiffeners. With the same cross-sectional area of stiffener, the T section stiffened plate shows longer fatigue life than L section stiffened plate. Meanwhile, the vibration fatigue life also shows great sensitivity to the spacing between the stiffeners.

Effect of vehicle weight on natural frequencies of bridges measured from traffic-induced vibration

Recently,ambient vibration test(AVT)is widely used tu estimate dynamic characteristics of large civil struc- tures.Dynamic characteristics ean be affected by various envirnnmental factors such as humidity,intensity of wind,and temperature.Besides these environmental conditions,tire mass of vehicles may change the measured valnes when traffic-in- duced vibration is used as a source of AVT tor bridges.The effect of vehicle mass on dynamic characteristics is investigated through traffic-induced vibration tests on three bridges;(1)three-span suspension bridge(128m+404m+128m),(2) five-span continuous steel box girder bridge(59m+3@ 95m+59m),(3)simply supported plate girder bridge(46m). Acceleration histories of each measurement location under normal traffic are recorded for 30 minutes at field.These recor- ded histories are divided into individual vibrations and are combined into two groups aceording to the level of vibration;one by heavy vehicles such as trucks and buses and the other by light vehicles such as passenger cars.Separate processing of the two groups of signals shows that,for the middle and long-span bridges,the difference can be hardly detected,but,for the short span bridges whose mass is relatively small,the measured natural frequencies can change up to 5.4%.

Structural Model Updating of Jacket Platform by Control Theory Using Vibration Measurement Approach

The identification of variations in the dynamic behavior of structures is an important subject in structural integrity assessment.Improvement and servicing of offshore platforms in the marine environment with constant changing,requires understanding the real behavior of these structures to prevent possible failure.In this work,empirical and numerical models of jacket structure are investigated.A test on experimental modal analysis is accomplished to acquire the response of structure and a mathematical model of the jacket structure is also performed.Then,based on the control theory using developed reduction system,the matrices of the platform model is calibrated and updated.The current methodology can be applied to prepare the finite element model to be more adaptable to the empirical model.Calibrated results with the proposed approach in this paper are very close to those of the actual model and also this technique leads to a reduction in the amount of calculations and expenses.The research clearly confirms that the dynamic behavior of fixed marine structures should be designed and assessed considering the calibrated analytical models for the safety of these structures.

Nonlinear Modeling and Identification of Structural Joint by Response Control Vibration Test

Components of mechanical product are assembled by structural joints,such as bolting,riveting,welding,etc.Structural joints introduce nonlinearity to some engineering structures,and the nonlinearity need to be modeled precisely.To meet serious quality requirements,it is necessary to detect and identify nonlinearity of mechanical products for structural optimization.Modal test to acquire a dynamic response has been applied for decades,which provides reliable results for finite element(FE)model updating.Here response control vibration test for identification of nonlinearity is presented.A nonlinear system can be regarded as linearity for particular steady state response,and classical linear analysis tool is applicable to extract modal data for particular response.First,its applicability is illustrated by some numerical simulations.Subsequently,it is implemented on experimental setup with structural joints by shaking table.The stiffness and damping function dependent of relative displacement are fitted to describe its inherent nonlinearity.The spring and damping forces are identified by harmonic balance method(HBM)to predict output response.Based on the identified results,the procedure is recommended that it allows a reliable measurement of nonlinearity with a certain accuracy.

Numerical and Experimental Study of Free Vibration Characteristics of a Cable-Stayed Bridge

The main aim of this study is to understand the dynamic behavior of a cable-stayed bridge, using both numerical and experimental analysis. A three-dimensional finite element model for the bridge was developed for the free vibration analysis and the ambient vibration properties of the bridge were determined through field testing. The experimental and numerical results of natural frequencies and the associated mode shapes were compared, and the high accuracy between them shows that the 3D model is capable of approximately representing the dynamic behavior of the bridge and the use of ambient vibration survives in future testing of the bridge. These dynamic characteristics can be used as the basis for updating the finite element model and also for global damage detection.

Reasons and laws of ground vibration amplification induced by vertical dynamic load

The phenomenon of ground vibration amplification caused by railway traffic was found and proved. In order to study the reasons which cause the amplification, a drop-weight test was performed. Then, the model for both homogeneous and layered soil subjected to a harmonic vertical load was built. With the help of this model, displacement Green's function was calculated and the propagation laws of ground vibration responses were discussed. Results show that: 1) When applying a harmonic load on the half-space surface, the amplitude of ground vibrations attenuate with fluctuation, which is caused by the superposition of bulk and Rayleigh waves. 2) Vibration amplification can be enlarged under the conditions of embedded source and the soil layers. 3) In practice, the fluctuant attenuation should be paid attention to especially for the vibration receivers who are sensitive to single low frequencies(<10 Hz). Moreover, for the case of embedded loads, it should also be paid attention to that the receivers are located at the place where the horizontal distance is similar to embedded depth, usually 10 to 30 m for metro lines.

Vibration Test Measures for Pump Fault Diagnosis

p;Calculation;Diagnosis The vibration measuring standard for compound machinery utilized in modern industrial production will be employed for the application of detecting technologies.The vibration intensity can be obtained by selecting the detecting method to obtain the speed of mechanical vibration,and technicians can examine whether the vibrating machinery is in a proper functioning state based on the value of vibration intensity,allowing for thorough fault diagnosis.In order to provide useful diagnosis ideas for technicians,this study examines the measurement of mechanical vibration and investigates the calculating method of mechanical vibration intensity.

Virtual vibration test rig for fatigue analysis of dozer push arms

To obtain accurate fatigue life results for construction machinery components,acquiring load spectra is crucial,as their authenticity and validity directly determine the precision of the analysis.In working conditions,component attitudes change continuously,but they remain static on the vibration test rig(VTR),so the acquired target signals should match with the actual component attitudes in the driving signal generation.This paper proposes an efficient and economical simulation-based virtual VTR for fatigue analysis of dozers.First,the relationship between the push arm rotation angle and the cylinder stroke is established,since the cylinder strokes can be measured easily in data acquisition experiments.Second,load decomposition is used to determine the attitude relationship between virtual VTR conditions and actual conditions,and target signals are calculated based on this attitude relationship and measured data.According to the system's frequency response function,the driving signals are iterated until the system's response signals converge with the target signals.Finally,the iteratively obtained load spectra are utilized for fatigue life analysis.The results show that the virtual VTR can effectively and accurately obtain the results of fatigue analysis and has engineering application significance.

Operational modal identification of suspension bridge based on structural health monitoring system

An output-only modal identification method by a combination use of the peak-picking method and the cross spectrum methods are presented. Meanwhile, a novel mode shape optimum method of the deck is proposed. The methods are applied to the operational modal identification system of the Runyang Suspension Bridge, which can be used to obtain the modal parameters of the bridge from out-only data sets collected by its structural health monitoring system （SHMS）. As an example, the vibration response data of the deck, cable and tower recorded during typhoon Matsa excitation are used to illustrate the program application. Some of the modal frequencies observed from deck vibration responses are also found in the vibration responses of the cable and the tower. The results show that some modal shapes of the deck are strongly coupled with the cable and the tower. By comparing the identification results from the operational modal system with those from field measurements, a good agreement between them is achieved, but some modal frequencies identified from the operational modal identification system （OMIS）, such as L1 and L2, obviously decrease compared with those from the field measurements.

Dynamic finite element model updating of prestressed concrete continuous box-girder bridge

The dynamic finite element model （FEM） of a prestressed concrete continuous box-girder bridge, called the Tongyang Canal Bridge, is built and updated based on the results of ambient vibration testing （AVT） using a real-coded accelerating genetic algorithm （RAGA）. The objective functions are defined based on natural frequency and modal assurance criterion （MAC） metrics to evaluate the updated FEM. Two objective functions are defined to fully account for the relative errors and standard deviations of the natural frequencies and MAC between the AVT results and the updated FEM predictions. The dynamically updated FEM of the bridge can better represent its structural dynamics and serve as a baseline in long-term health monitoring, condition assessment and damage identification over the service life of the bridge .

Optimal sensor placement in hydropower house based on improved triaxial effective independence method

The capacity and size of hydro-generator units are increasing with the rapid development of hydroelectric enterprises, and the vibration of the powerhouse structure has increasingly become a major problem. Field testing is an important method for research on dynamic identification and vibration mechanisms. Research on optimal sensor placement has become a very important topic due to the need to obtain effective testing information from limited test resources. To overcome inadequacies of the present methods, this paper puts forward the triaxial effective independence driving-point residue （EfI3-DPR3） method for optimal sensor placement. The Efl3-DPR3 method can incorporate both the maximum triaxial modal kinetic energy and linear independence of the triaxial target modes at the selected nodes. It was applied to the optimal placement oftriaxial sensors for vibration testing in a hydropower house, and satisfactory results were obtained. This method can provide some guidance for optimal placement of triaxial sensors of underground powerhouses.

USING CROSS-CORRELATION THEORY TO EXTRACT MODAL PARAMETERS IN FREQUENCY- DOMAIN

Conventional modal parameter identifications are usually based on frequencyresponse functions, which require measurements of both the input force and the resulting response.However, in many cases, only response data are available while the actual excitations (such aswind/wave load) are not measurable. Modal parameters estimation must base itself on response-onlydata. Over the past years, many time-domain modal parameter identification techniques fromoutput-only are proposed. A poly-reference frequency-domain modal identification scheme onresponse-only is presented. It is based on coupling the cross-correlation theory with conventionalfrequency-domain modal parameter extraction. An experiment using an airplane model is performed toverify the proposed method.

Finite Element Model Updating for Structural Health Monitoring

This paper provides a model updating approach to detect,locate,and char-acterize damage in structural and mechanical systems by examining changes in mea-sured vibration responses.Research in vibration-based damage identification has been rapidly expanding over the last few decades.The basic idea behind this technology is that modal parameters(notably frequencies,mode shapes,and modal damping)are functions of the physical properties of the structure(mass,damping,and sifies).Therefore,changes in the physical properties will cause changes in the modal proper-ties which could be obtained by structural health monitoring(SHM).Updating is a process fraught with numerical difficulties.These arise from inaccuracy in the model and imprecision and lack of information in the measurements,mainly taken place in joints and critical points.The motivation for the development of this technology is.presented,methods are categorized according to various criteria such as the level of damage detection provided from vibration testing,natural frequency and mode shape readings are then obtained by using modal analysis techniques,which are used for updating structural parameters of the associated finite element model The experi-mental studies for the laboratory tested bridge model show that the proposed model.updating using ME scope technique can provide reasonable model updating results.

ISOLATION DESIGN AND SIMULATIONAL EXPERIMENT OF NANOMETER MICRO MOVEMENT TEST-BED

The relation of mass, stiffness and rate of damping is obtained by using the mechanical analysis of the obstructive vibration system of two dimensions for the design of the obstructive vibration system of more freedom and the micro vibration test bed. The result of stimulational experiment indicates that the isolation of vibration of this system is satisfactory. The design method of vibration can be used as the reference to ultra precision machine tool, super micro orientation machanism and so on.

Structural health monitoring of long-span suspension bridges using wavelet packet analysis

During the service life of civil engineering structures such as long-span bridges, local damage at key positions may continually accumulate, and may finally result in their sudden failure. One core issue of global vibration-based health monitoring methods is to seek some damage indices that are sensitive to structural damage, This paper proposes an online structural health monitoring method for long-span suspension bridges using wavelet packet transform （WPT）. The WPT- based method is based on the energy variations of structural ambient vibration responses decomposed using wavelet packet analysis. The main feature of this method is that the proposed wavelet packet energy spectrum （WPES） has the ability to detect structural damage from ambient vibration tests of a long-span suspension bridge. As an example application, the WPES-based health monitoring system is used on the Runyang Suspension Bridge under daily environmental conditions. The analysis reveals that changes in environmental temperature have a long-term influence on the WPES, while the effect of traffic loadings on the measured WPES of the bridge presents instantaneous changes because of the nonstationary properties of the loadings. The condition indication indices VD reflect the influences of environmental temperature on the dynamic properties of the Runyang Suspension Bridge. The field tests demonstrate that the proposed WPES-based condition indication index VD is a good candidate index for health monitoring of long-span suspension bridges under ambient excitations.

In-Situ Test on Fatigue Characteristics of Top-Mounted Dividable Pile-Board Subgrade for High-Speed Railway

To simulate the fatigue characteristics of the pile-board structure under long-term dynamic load, using the in-situ dynamic testing system DTS-1, the forced vibration loading was repeated one million times at different cross-sections of the pile-board structure for high-speed railway. The dynamic deformation, permanent deformation and dynamic stress of main reinforcements were measured. The test results show that the dynamic responses of the pile-board structure almost did not vary with the forced vibration times under the simulated trainload. After one million times of forced vibration, the permanent deformations of the midspan section of intermediate span and midspan section of side span were 0.7 mm and 0. 6 mm, respectively, and there was no accumulative plastic deformation at the bearing section of intermediate span.

Frequencies Prediction of Laminated Timber Plates Using ANN Approach

Cross laminated timber(CLT)panels,which are used as load bearing plates and shear panels in timber structures,can serve as roofs,walls and floors.Since timber is construction material with relatively less stiffness,the design of such structures is often driven by serviceability criteria,such as deflection and vibration.Therefore,accurate vibration and elastic properties are vital for engineered CLT products.The objective of this research is to explore a method to determine the natural frequencies of orthotropic wood plates efficiently and fast.The method was developed based on vibration signal processing by wavelet to acquire the effective sample data,and a model developed by artificial neural network(ANN)to achieve the prediction of nature frequencies.First,experiments were performed to obtain vibration signals of single-layer plates.The vibration signals were then processed by wavelet packet transform to extract the eigenvectors,which served as the samples to train the ANN model.The trained model was employed to predict three nature frequencies of other test specimens.The results showed that the proposed method can produce predicted frequencies fast and efficiently within 10%of the measured values.

A new bracing system for improvement of seismic performance of steel jacket type offshore platforms with float-over-deck

In this paper, the seismic response of a newly designed steel jacket offshore platform with a float over deck （FOD） system in the Persian Gulf was investigated through incremental dynamic analysis. Comparison of incremental dynamic analysis results for both directions of the platform shows that the lateral strength of the platform in the float over direction is less than its lateral strength in other direction. Dynamic characteristics measurement of a scale model of platform was also performed using forced vibration tests. From experimental measurement of the scaled model, it was observed that dynamic characteristic of the platform is different in the float over direction compared to the other direction. Therefore, a new offshore installed bracing system for the float over direction was proposed for improvement of seismic performance of this type of platform. Finally, the structure with the modified system was assessed using the probabilistic seismic assessment method as well as experimental measurement of its dynamic characteristics. It was observed that the proposed offshore installed bracing system improves the performance of platforms subjected to strong ground motion.

Field measurements for calibration of simplified models of the stiffening effect of infill masonry walls in high-rise RC framed and shear-wall buildings

As a type of nonstructural component, infill walls play a significant role in the seismic behavior of high-rise buildings. However, the stiffness of the infill wall is generally either ignored or considered by simplified empirical criteria that lead to a period shortening. The difference can be greatly decreased by using a structural identification methodology. In this study, an ambient vibration test was performed on four on-site reinforced concrete high-rise buildings, and the design results were compared with the PKPM models using corresponding finite element(FE) models. A diagonal strut model was used to simulate the behavior of the infill wall, and the identified modal parameters measured from the on-site test were employed to calibrate the parameters of the diagonal strut in the FE models. The SAP2000 models with calibrated elastic modulus were used to evaluate the seismic response in the elastic state. Based on the load-displacement relationship of the infill wall, nonlinear dynamic analysis models were built in PERFORM-3 D and calibrated using the measured modal periods. The analysis results revealed that the structural performance under small/large earthquake records were both strengthened by infill walls, and the contribution of infill walls should be considered for better accuracy in the design process.