Accurate measurement of the evolution of rock joint void geometry is essential for comprehending the distribution characteristics of asperities responsible for shear and seepage behaviors.However,existing techniques o...Accurate measurement of the evolution of rock joint void geometry is essential for comprehending the distribution characteristics of asperities responsible for shear and seepage behaviors.However,existing techniques often require specialized equipment and skilled operators,posing practical challenges.In this study,a cost-effective photogrammetric approach is proposed.Particularly,local coordinate systems are established to facilitate the alignment and precise quantification of the relative position between two halves of a rock joint.Push/pull tests are conducted on rock joints with varying roughness levels to induce different contact states.A high-precision laser scanner serves as a benchmark for evaluating the photogrammetry method.Despite certain deviations exist,the measured evolution of void geometry is generally consistent with the qualitative findings of previous studies.The photogrammetric measurements yield comparable accuracy to laser scanning,with maximum errors of 13.2%for aperture and 14.4%for void volume.Most joint matching coefficient(JMC)measurement errors are below 20%.Larger measurement errors occur primarily in highly mismatched rock joints with JMC values below 0.2,but even in cases where measurement errors exceed 80%,the maximum JMC error is only 0.0434.Thus,the proposed photogrammetric approach holds promise for widespread application in void geometry measurements in rock joints.展开更多
To investigate the effect of void defects on the shock response of hexanitrohexaazaisowurtzitane(CL-20)co-crystals,shock responses of CL-20 co-crystals with energetic materials ligands trinitrotoluene(TNT),1,3-dinitro...To investigate the effect of void defects on the shock response of hexanitrohexaazaisowurtzitane(CL-20)co-crystals,shock responses of CL-20 co-crystals with energetic materials ligands trinitrotoluene(TNT),1,3-dinitrobenzene(DNB),solvents ligands dimethyl carbonate(DMC) and gamma-butyrolactone(GBL)with void were simulated,using molecular dynamics method and reactive force field.It is found that the CL-20 co-crystals with void defects will form hot spots when impacted,significantly affecting the decomposition of molecules around the void.The degree of molecular fragmentation is relatively low under the reflection velocity of 2 km/s,and the main reactions are the formation of dimer and the shedding of nitro groups.The existence of voids reduces the safety of CL-20 co-crystals,which induced the sensitivity of energetic co-crystals CL-20/TNT and CL-20/DNB to increase more significantly.Detonation has occurred under the reflection velocity of 4 km/s,energetic co-crystals are easier to polymerize than solvent co-crystals,and are not obviously affected by voids.The results show that the energy of the wave decreases after sweeping over the void,which reduces the chemical reaction frequency downstream of the void and affects the detonation performance,especially the solvent co-crystals.展开更多
To address the issue of horizontal well production affected by the distribution of perforation density in the wellbore,a numerical model for simulating two-phase flow in a horizontal well is established under two perf...To address the issue of horizontal well production affected by the distribution of perforation density in the wellbore,a numerical model for simulating two-phase flow in a horizontal well is established under two perforation density distribution conditions(i.e.increasing the perforation density at inlet and outlet sections respectively).The simulation results are compared with experimental results to verify the reliability of the numerical simulation method.The behaviors of the total pressure drop,superficial velocity of air-water two-phase flow,void fraction,liquid film thickness,air production and liquid production that occur with various flow patterns are investigated under two perforation density distribution conditions based on the numerical model.The total pressure drop,superficial velocity of the mixture and void fraction increase with the air flow rate when the water flow rate is constant.The liquid film thickness decreases when the air flow rate increases.The liquid and air productions increase when the perforation density increases at the inlet section compared with increasing the perforation density at the outlet section of the perforated horizontal wellbore.It is noted that the air production increases with the air flow rate.Liquid production increases with the bubble flow and begins to decrease at the transition point of the slug-stratified flow,then increases through the stratified wave flow.The normalized liquid flux is higher when the perforation density increases at the inlet section,and increases with the radial air flow rate.展开更多
The awareness amongst the researchers to develop an environment friendly sustainable material leads to explore new class of plant-based fiber for making composites. Hybridization of such plant-based fiber with inclusi...The awareness amongst the researchers to develop an environment friendly sustainable material leads to explore new class of plant-based fiber for making composites. Hybridization of such plant-based fiber with inclusion of engineered fiber is one of the promising methods to not only enhanced the mechanical performance but also suppressed the drawbacks that associate with such plant-based fiber to some extent. A usual hand lay-up method was taken-up in this work to fabricate four layered of hybrid kenaf(K)/glass(G)polyester laminates with different stacking order such as KKKK,KGKG,KGGK,GKKG and GGGG. The erosive character of the laminates was examined under three distinct particle velocities(48m/s, 70m/s,82m/s)and four different impact angles(30°, 45°, 60°, 90°). All fabricated laminates exhibited a semiductile character at lower velocities(48m/s and70m/s)as peak wear rate was observed at45° impact angle. However,they showed a semi-brittle character at high velocity(82m/s)as maximum rate of erosion was noticed at60° impact angle. Again,the influence of stacking order of piles on erosion wear was also clearly noticed. Moreover,the semi-brittle/semi-ductile characterization was also evidenced in accordance to the range of erosion efficiencies. The micro-structures of worn surfaces were inspected thoroughly from the images of scanning electron microscope(SEM)to evident the mechanism of erosion.展开更多
This work is focused to examine the erosive performance of hybrid Palmyra palm leaf stalk fiber(PPLSF)/glass polyester laminate against solid particle bombardment.A hand lay-up method was adopted for the fabricating f...This work is focused to examine the erosive performance of hybrid Palmyra palm leaf stalk fiber(PPLSF)/glass polyester laminate against solid particle bombardment.A hand lay-up method was adopted for the fabricating four piles of five distinct laminates with different stacking order glass and PPLSF layers.Amongst them,one group of pure PPLSF and pure E-glass laminates were fabricated.The hybrid laminates were exposed to high speed stream of solid sand particle at three distinct impact velocities(48,70 and 82 m/s)and four different angles of impingement(30°,45°,60°and 90°).The effect of particle velocity,angle of impingement and stacking order on both wear rate and efficiency were highlighted.The experimental assessment reveals a significant improvement in erosive wear resistance properties due to hybridization of PPLSF with E-glass.Again,the laminates with PPLSF layer as skin and glass as core layer exhibited better erosive wear resistance properties than other types of laminates.Further,a maximum value of erosion at lower velocity(48 m/s)is also noticed at 45°impingement angle.However,at high velocity of impact 70 m/s and 82 m/s,the maximum rate of erosion has been shifted from 45°impact angle to 60°impact angle.The alternation of this semi-ductile character to semi-brittle character is evidenced by analyzing the experimental data.Further to justify the mode of erosion,the eroded surface samples were inspected by scanning electron microscope(SEM).展开更多
We propose that the QCD vacuum pion tetrahedron condensate density vary in space and drops to extremely low values in the Kennan, Barger and Cowie (KBC) void in analogy to earth’s atmospheric density drop with elevat...We propose that the QCD vacuum pion tetrahedron condensate density vary in space and drops to extremely low values in the Kennan, Barger and Cowie (KBC) void in analogy to earth’s atmospheric density drop with elevation from earth. We propose a formula for the gravitation acceleration based on the non-uniform pion tetrahedron condensate. Gravity may be due to the underlying microscopic attraction between quarks and antiquarks, which are part of the vacuum pion tetrahedron condensate. We propose an electron tetrahedron model, where electrons are comprised of tetraquark tetrahedrons, and . The quarks determine the negative electron charge and the or quarks determine the electron two spin states. The electron tetrahedron may perform a high frequency quark exchange reactions with the pion tetrahedron condensate by tunneling through the condensation gap creating a delocalized electron cloud with a fixed spin. The pion tetrahedron may act as a QCD glue bonding electron pairs in atoms and molecules and protons to neutrons in the nuclei. Conservation of valence quarks and antiquarks is proposed.展开更多
The present paper is inspired by the article “Ho’oleilana: An Individual Baryon Acoustic Oscillation?” published by R. B. Tully, C. Howlett, and D. Pomarède on Sep. 2023 [1]. They claim: Evidence is presented ...The present paper is inspired by the article “Ho’oleilana: An Individual Baryon Acoustic Oscillation?” published by R. B. Tully, C. Howlett, and D. Pomarède on Sep. 2023 [1]. They claim: Evidence is presented here for the discovery of a remarkably strong individual contribution to the baryon acoustic oscillation (BAO) signal at z = 0.068, an entity that is given the name Ho’oleilana. K. Dawson, co-spokesperson for Dark Energy Spectroscopic Instrument is more inclined to believe that this latest finding is something of a coincidence, a chance alignment that simply looks like a sphere with a radius around what you’d expect for a BAO [2]. In this paper, we provide a short summary of experimental observations of Boötes Void and Superclusters;discuss the main features of the developed Hypersphere World-Universe Model;introduce notions “Cosmic Voids” and “Cosmic Bubbles”;elaborate a mathematical framework for different types of Cosmic Bubbles (Hubble Spherical Bubble for the World, Disk Bubbles for Galaxies;Spherical Bubbles for Extrasolar Systems, Dark Matter (DM) Spherical Bubbles for Galaxies and Superclusters);make a conclusion that the Boötes is a DM Cosmic Bubble and suggest experiments, which confirm our conclusion.展开更多
A computationally efficient two-surface plasticity model is assessed against crystal plasticity. Focus is laid on the mechanical behavior of magnesium alloys in the presence of ductility-limiting defects, such as void...A computationally efficient two-surface plasticity model is assessed against crystal plasticity. Focus is laid on the mechanical behavior of magnesium alloys in the presence of ductility-limiting defects, such as voids. The two surfaces separately account for slip and twinning such that the constitutive formulation captures the evolving plastic anisotropy and evolving tension-compression asymmetry. For model identification, a procedure is proposed whereby the initial guess is based on a combination of experimental data and computationally intensive polycrystal calculations from the literature. In drawing direct comparisons with crystal plasticity, of which the proposed model constitutes a heuristically derived reduced-order model, the available crystal plasticity simulations are grouped in two datasets. A calibration set contains minimal data for both pristine and porous material subjected to one loading path. Then the two-surface model is assessed against a broader set of crystal plasticity simulations for voided unit cells under various stress states and two loading orientations. The assessment also includes microstructure evolution(rate of growth of porosity and void distortion). The ability of the two-surface model to capture essential features of crystal plasticity is analyzed along with an evaluation of computational cost. The prospects of using the model in guiding the development of physically sound damage models in Mg alloys are put forth in the context of high-throughput simulations.展开更多
The distribution characteristics of air voids in ultrathin asphalt friction course(UAFC) samples with different gradations and compaction methods were statistically analyzed using X-ray computed tomography(CT) and ima...The distribution characteristics of air voids in ultrathin asphalt friction course(UAFC) samples with different gradations and compaction methods were statistically analyzed using X-ray computed tomography(CT) and image analysis techniques. Based on the results, compared with the AC-5 sample, the OGFC-5mixture has a higher air void ratio, a larger air void size and a greater number of air voids, with the distribution of internal air voids being more uniform and their shapes being more rounded. The two-parameter Weibull function was applied to fit the gradation of air voids. The fitting results is good, and the function parameters are sensitive to changes in both mineral gradation and compaction method. Moreover, two homogeneity indices were proposed to evaluate the compaction uniformity of UAFC samples. Compared with the Marshall method,the SGC method is more conducive to improve the compaction uniformity of UAFC samples. The compaction method significantly influences the air void distribution characteristics and compaction uniformity of AC-5sample, but has a less significant impact on OGFC-5 sample. The experimental results in the study provides a solid foundation for further explorations on the internal structure and mixture design of UAFC.展开更多
Automated X-ray defect inspection of occluded objects has been an essential topic in semiconductors,autonomous vehicles,and artificial intelligence devices.However,there are few solutions to segment occluded objects i...Automated X-ray defect inspection of occluded objects has been an essential topic in semiconductors,autonomous vehicles,and artificial intelligence devices.However,there are few solutions to segment occluded objects in the X-ray inspection efficiently.In particular,in the Ball Grid Array inspection of X-ray images,it is difficult to accurately segment the regions of occluded solder balls and detect defects inside solder balls.In this paper,we present a novel automatic inspection algorithm that segments solder balls,and detects defects fast and efficiently when solder balls are occluded.The proposed algorithm consists of two stages.In the first stage,the defective candidates or defects are determined through the following four steps:(i)image preprocessing such as noise removal,contrast enhancement,binarization,connected component,and morphology,(ii)limiting the inspec-tion area to the ball regions and determining if the ball regions are occluded,(iii)segmenting each ball region into one or more regions with similar gray values,and(iv)determining whether there are defects or defective candidates in the regions using a weighted sum of local threshold on local variance.If there are defective candidates,the determination of defects is finally made in the following stage.In the second stage,defects are detected using the automated inspection technique based on oblique computed tomography.The 3D precision inspection process is divided into four steps:(i)obtaining 360 projection images(one image per degree)rotating the object from 0 to 360 degrees,(ii)reconstructing a 3D image from the 360 projected images,(iii)finding the center slice of gravity for solder balls from the axial slice images in the z-direction,and getting the inspection intervals between the upper bound and the lower bound from the center slice,and(iv)finally determining whether there are defects in the averaged image of solder balls.The proposed hybrid algorithm is robust for segmenting the defects inside occluded solder balls,and improves the performance of solder ball segmentation and defect detection algorithm.Experimental results show an accuracy of more than 97%.展开更多
Objective To determine the prevalence of lower urinary tract symptoms(LUTS)and their severity population in Jordan.Methods This cross-sectional survey was conducted using a paper-based survey between August and Septem...Objective To determine the prevalence of lower urinary tract symptoms(LUTS)and their severity population in Jordan.Methods This cross-sectional survey was conducted using a paper-based survey between August and September in 2019.The study was carried out in the health care centers or hospitals in three different regions of Jordan:North(Irbid and Jarash),Middle(Amman,Madaba,Salt,and Zarqa),and South(Karak and Aqaba).Results To estimate the prevalence of LUTS,two definitions were used,including the first definition(presence of any LUTS regardless of the degree of severity)and the second definition(presence of any LUTS that occurs half the time or more).According to the first definition,1038(89.9%)reported LUTS(male:47.3%,female:52.7%),while 763(66.1%)reported LUTS according to the second definition(male:45.6%,female:54.4%).According to the International Prostate Symptom Score characterization,73.9%had nocturia and 62.9%reported daytime increased frequency.Conclusion LUTS are highly prevalent among the Jordanian population,and more than half of them have nocturia or daytime increased frequency as most frequently reported symptoms.展开更多
The thermal conductivity of marine sediments is an important thermophysical parameter in the study of seafloor heat flow and marine engineering construction.Understanding the effect of thermal conductivity of marine s...The thermal conductivity of marine sediments is an important thermophysical parameter in the study of seafloor heat flow and marine engineering construction.Understanding the effect of thermal conductivity of marine sediments in the environment has a major engineering value and theoretical significance.In this work,a modified test method was used to measure the thermal conductivity of silt in the Yellow River Delta under different void ratios,moisture contents,temperatures,and salinities.Results showed that the thermal conductivity of silt in the Yellow River Delta decreased with the increase in the void ratio and increased with the water content.Compared with sand and clay,silt in the Yellow River Delta was the least affected by the void ratio and moisture content.Under low temperatures,the heat transfer of soil was controlled by the average velocity of the phonons;therefore,the thermal conductivity of silt in the Yellow River Estuary increased with temperature.The thermal conductivity of pore water decreased with increasing salinity.Moreover,certain salinity levels resulted in a phenomenon known as the‘compressing twin electrical layer’,which led to an increase in the contact area between soil particles.With the increase in salinity,the thermal conductivity of silt in the Yellow River Delta experiences an initial decline and a subsequent increase.The proposed thermal conductivity test method is more accurate than the existing technique,and the findings provide a basis for further study on the thermal characteristics of submarine sediments.展开更多
Large vertical pipes are key structures connecting subsea wells to offshore platforms.However,existing studies mainly focus on small vertical pipes.In a vertical acrylic pipe with 80 mm inner diameter and 11 m height,...Large vertical pipes are key structures connecting subsea wells to offshore platforms.However,existing studies mainly focus on small vertical pipes.In a vertical acrylic pipe with 80 mm inner diameter and 11 m height,a high-speed camera was used to visually research the influences of pipe diameters,liquid properties and inlet effect on air-water co-flow characteristic.Different flow regime maps of vertical pipes(diameters are in the range of 50e189 mm)were compared and the critical gas velocity of the transition boundary from bubble to slug flow tended to increase with the increase of diameters at D≥80 mm.Drift-flux models were established in different flow regimes and liquid properties have a significant effect on drift coefficients of bubble flow and slug flow(void fraction a≤0.4).The influence of inlet turbulent effect on the gas-liquid interface distribution gradually weakened and disappeared from the pipe base to 85D,where the flow was fully developed.Slug frequency has a trend of increase first and then decrease with the gas Weber numbers increasing at low liquid superficial velocities(J_(L)≤0.31 m/s).And on the basis of this law,a new slug frequency correlation was proposed.It was found that there was an exponential relationship between the ratio of lengths of Taylor bubble to slug and the void fraction.展开更多
The prevalent view endorses that the force of gravitation of the earth is directed towards the centre of the planet, in consequence of which, temperature and pressure at the deepest part of the planet must be very hig...The prevalent view endorses that the force of gravitation of the earth is directed towards the centre of the planet, in consequence of which, temperature and pressure at the deepest part of the planet must be very high. This view leads to the conclusion that the inner core or deepest part of the planet, though constituted of iron through which magnetic lines of force emanate, cannot be magnetic. The author has shown that amongst the earth’s three geospheres, fluid outer core that occurs between mantle and inner core, is a void zone which, because of the association of some particles from the mantle, apparently shows fluid characteristics. Occurrence of a virtually void zone in the planet’s deep interior separated by a solid mantle and iron inner core would generate a reversely directed gravitational force due to which pressure and temperature at the deepest part of the earth would be sufficiently low. Hence, the earth’s solid inner core, constituted of iron, is a dipolar permanent magnet. The paper envisages that the concept of reverse gravity presented here needs to be validated by physicists since it is an original view. The concept put forward here, not only explains the cause of earth’s magnetic phenomena, but also elucidates continental drifting and several other features of the planet in a scientifically accepted manner, thereby refuting the possibility of occurrence of convection current in the mantle which is solid and rigid.展开更多
The article puts forward a hypothesis about the possibility of the existence of our Universe inside a supermassive black hole, analyzes the basic assumptions and verifiable physical consequences. The transformation of...The article puts forward a hypothesis about the possibility of the existence of our Universe inside a supermassive black hole, analyzes the basic assumptions and verifiable physical consequences. The transformation of the Primary Particles obtained from the decay of Borromeo rings into binary and ternary structures is considered separately, taking into account how the percentages between Dark Matter, Dark Energy and Baryonic matter are formed. A system of kinetic equations has been compiled, which makes it possible to develop a theoretical approach to obtain these values depending on the geometric and physical characteristics of interacting particles. The possibility and necessity of the existence of a Primary Relic of Primary Particles are substantiated. The nature of the voids and the analytical solution of the Einstein equations obtained from the generalized Papapetrou solution, which leads to the existence of strings with an arbitrary distribution of matter along the string and with lengths comparable to the size of the Universe, are considered. In the case of a string of finite size and constant density, this solution leads to the well-known Weyl solution. An assumption is put forward about the existence of an Einstein-Rosen type transition, when the dimensions of the white and black holes at the ends of this transition have different dimensions.展开更多
We propose that the exotic meson tetraquark u<sub>d</sub>~</sup>dũintroduced in previous papers, may be a pseudo-Goldstone boson having a tetrahedron geometry and symmetry. The transition ...We propose that the exotic meson tetraquark u<sub>d</sub>~</sup>dũintroduced in previous papers, may be a pseudo-Goldstone boson having a tetrahedron geometry and symmetry. The transition from the neutral pion superposition of two free mesons, d<sub>d</sub>~</sup> and uũ, to the tetrahedron geometry with optional two chiral states may be the symmetry breaking of the QCD ground state. The u<sub>d</sub>~</sup>dũtetrahedron mass may be calculated by measuring the β decay rate variability. We assume that electrons and positrons are composite particle exotic tetraquarks, dũd<sub>d</sub>~</sup> for the electrons and u<sub>d</sub>~</sup>d<sub>d</sub>~</sup> for the positrons and confined by the strong force. We propose that the QCD tetrahedrons play a central role in electron pairing mechanism in both chemical bond forming and superconductor Cooper pairs. We propose a hypothesis where the QCD ground state tetrahedrons play a central role in low energy physics where quark exchange reactions between particles and the QCD tetrahedrons via gluon junctions transfer all the forces. The QCD ground state u<sub>d</sub>~</sup>dũtetrahedrons hypothesis provides a symmetry breaking and a mass gap may be created by the ground state QCD tetrahedrons Bose-Einstein condensate.展开更多
As translating in most cases is considered a bicultural or even multicultural activity,cultural discrepancies and voids inevitably occur during the language decoding and encoding process of the translating.This is a h...As translating in most cases is considered a bicultural or even multicultural activity,cultural discrepancies and voids inevitably occur during the language decoding and encoding process of the translating.This is a heated issue that has existed for long,and translators frequently turn to two major approaches for a solutiondomestication and foreignization.However,no matter which approach a translator chooses,it is essential to make a comprehensive analysis of the cultural and influential factors that contained in the source language text,rather than simply checking through a dictionary or cyclopedia.Based on the types of culture classified by Professor Chen Hongweimaterial culture,institutional culture and mental culture,the following discussion will make an exemplification of the merits and choice between domestication and foreignization,concerning the relation between culture types and translating approaches.展开更多
基金supported by the National Natural Science Foundation of China (Nos.42207175 and 42177117)the Ningbo Natural Science Foundation (No.2022J115)。
文摘Accurate measurement of the evolution of rock joint void geometry is essential for comprehending the distribution characteristics of asperities responsible for shear and seepage behaviors.However,existing techniques often require specialized equipment and skilled operators,posing practical challenges.In this study,a cost-effective photogrammetric approach is proposed.Particularly,local coordinate systems are established to facilitate the alignment and precise quantification of the relative position between two halves of a rock joint.Push/pull tests are conducted on rock joints with varying roughness levels to induce different contact states.A high-precision laser scanner serves as a benchmark for evaluating the photogrammetry method.Despite certain deviations exist,the measured evolution of void geometry is generally consistent with the qualitative findings of previous studies.The photogrammetric measurements yield comparable accuracy to laser scanning,with maximum errors of 13.2%for aperture and 14.4%for void volume.Most joint matching coefficient(JMC)measurement errors are below 20%.Larger measurement errors occur primarily in highly mismatched rock joints with JMC values below 0.2,but even in cases where measurement errors exceed 80%,the maximum JMC error is only 0.0434.Thus,the proposed photogrammetric approach holds promise for widespread application in void geometry measurements in rock joints.
基金supported by the National Natural Science Foundation of China (22275018)the Project of State Key Laboratory of Explosion Science and Technology (Beijing Institute of Technology)(Grant No.QNKT20-04)。
文摘To investigate the effect of void defects on the shock response of hexanitrohexaazaisowurtzitane(CL-20)co-crystals,shock responses of CL-20 co-crystals with energetic materials ligands trinitrotoluene(TNT),1,3-dinitrobenzene(DNB),solvents ligands dimethyl carbonate(DMC) and gamma-butyrolactone(GBL)with void were simulated,using molecular dynamics method and reactive force field.It is found that the CL-20 co-crystals with void defects will form hot spots when impacted,significantly affecting the decomposition of molecules around the void.The degree of molecular fragmentation is relatively low under the reflection velocity of 2 km/s,and the main reactions are the formation of dimer and the shedding of nitro groups.The existence of voids reduces the safety of CL-20 co-crystals,which induced the sensitivity of energetic co-crystals CL-20/TNT and CL-20/DNB to increase more significantly.Detonation has occurred under the reflection velocity of 4 km/s,energetic co-crystals are easier to polymerize than solvent co-crystals,and are not obviously affected by voids.The results show that the energy of the wave decreases after sweeping over the void,which reduces the chemical reaction frequency downstream of the void and affects the detonation performance,especially the solvent co-crystals.
基金the financial support from the Ministry of Education Malaysia under the Fundamental Research Grant Scheme(FRGS)scheme(20180110FRGS)。
文摘To address the issue of horizontal well production affected by the distribution of perforation density in the wellbore,a numerical model for simulating two-phase flow in a horizontal well is established under two perforation density distribution conditions(i.e.increasing the perforation density at inlet and outlet sections respectively).The simulation results are compared with experimental results to verify the reliability of the numerical simulation method.The behaviors of the total pressure drop,superficial velocity of air-water two-phase flow,void fraction,liquid film thickness,air production and liquid production that occur with various flow patterns are investigated under two perforation density distribution conditions based on the numerical model.The total pressure drop,superficial velocity of the mixture and void fraction increase with the air flow rate when the water flow rate is constant.The liquid film thickness decreases when the air flow rate increases.The liquid and air productions increase when the perforation density increases at the inlet section compared with increasing the perforation density at the outlet section of the perforated horizontal wellbore.It is noted that the air production increases with the air flow rate.Liquid production increases with the bubble flow and begins to decrease at the transition point of the slug-stratified flow,then increases through the stratified wave flow.The normalized liquid flux is higher when the perforation density increases at the inlet section,and increases with the radial air flow rate.
文摘The awareness amongst the researchers to develop an environment friendly sustainable material leads to explore new class of plant-based fiber for making composites. Hybridization of such plant-based fiber with inclusion of engineered fiber is one of the promising methods to not only enhanced the mechanical performance but also suppressed the drawbacks that associate with such plant-based fiber to some extent. A usual hand lay-up method was taken-up in this work to fabricate four layered of hybrid kenaf(K)/glass(G)polyester laminates with different stacking order such as KKKK,KGKG,KGGK,GKKG and GGGG. The erosive character of the laminates was examined under three distinct particle velocities(48m/s, 70m/s,82m/s)and four different impact angles(30°, 45°, 60°, 90°). All fabricated laminates exhibited a semiductile character at lower velocities(48m/s and70m/s)as peak wear rate was observed at45° impact angle. However,they showed a semi-brittle character at high velocity(82m/s)as maximum rate of erosion was noticed at60° impact angle. Again,the influence of stacking order of piles on erosion wear was also clearly noticed. Moreover,the semi-brittle/semi-ductile characterization was also evidenced in accordance to the range of erosion efficiencies. The micro-structures of worn surfaces were inspected thoroughly from the images of scanning electron microscope(SEM)to evident the mechanism of erosion.
文摘This work is focused to examine the erosive performance of hybrid Palmyra palm leaf stalk fiber(PPLSF)/glass polyester laminate against solid particle bombardment.A hand lay-up method was adopted for the fabricating four piles of five distinct laminates with different stacking order glass and PPLSF layers.Amongst them,one group of pure PPLSF and pure E-glass laminates were fabricated.The hybrid laminates were exposed to high speed stream of solid sand particle at three distinct impact velocities(48,70 and 82 m/s)and four different angles of impingement(30°,45°,60°and 90°).The effect of particle velocity,angle of impingement and stacking order on both wear rate and efficiency were highlighted.The experimental assessment reveals a significant improvement in erosive wear resistance properties due to hybridization of PPLSF with E-glass.Again,the laminates with PPLSF layer as skin and glass as core layer exhibited better erosive wear resistance properties than other types of laminates.Further,a maximum value of erosion at lower velocity(48 m/s)is also noticed at 45°impingement angle.However,at high velocity of impact 70 m/s and 82 m/s,the maximum rate of erosion has been shifted from 45°impact angle to 60°impact angle.The alternation of this semi-ductile character to semi-brittle character is evidenced by analyzing the experimental data.Further to justify the mode of erosion,the eroded surface samples were inspected by scanning electron microscope(SEM).
文摘We propose that the QCD vacuum pion tetrahedron condensate density vary in space and drops to extremely low values in the Kennan, Barger and Cowie (KBC) void in analogy to earth’s atmospheric density drop with elevation from earth. We propose a formula for the gravitation acceleration based on the non-uniform pion tetrahedron condensate. Gravity may be due to the underlying microscopic attraction between quarks and antiquarks, which are part of the vacuum pion tetrahedron condensate. We propose an electron tetrahedron model, where electrons are comprised of tetraquark tetrahedrons, and . The quarks determine the negative electron charge and the or quarks determine the electron two spin states. The electron tetrahedron may perform a high frequency quark exchange reactions with the pion tetrahedron condensate by tunneling through the condensation gap creating a delocalized electron cloud with a fixed spin. The pion tetrahedron may act as a QCD glue bonding electron pairs in atoms and molecules and protons to neutrons in the nuclei. Conservation of valence quarks and antiquarks is proposed.
文摘The present paper is inspired by the article “Ho’oleilana: An Individual Baryon Acoustic Oscillation?” published by R. B. Tully, C. Howlett, and D. Pomarède on Sep. 2023 [1]. They claim: Evidence is presented here for the discovery of a remarkably strong individual contribution to the baryon acoustic oscillation (BAO) signal at z = 0.068, an entity that is given the name Ho’oleilana. K. Dawson, co-spokesperson for Dark Energy Spectroscopic Instrument is more inclined to believe that this latest finding is something of a coincidence, a chance alignment that simply looks like a sphere with a radius around what you’d expect for a BAO [2]. In this paper, we provide a short summary of experimental observations of Boötes Void and Superclusters;discuss the main features of the developed Hypersphere World-Universe Model;introduce notions “Cosmic Voids” and “Cosmic Bubbles”;elaborate a mathematical framework for different types of Cosmic Bubbles (Hubble Spherical Bubble for the World, Disk Bubbles for Galaxies;Spherical Bubbles for Extrasolar Systems, Dark Matter (DM) Spherical Bubbles for Galaxies and Superclusters);make a conclusion that the Boötes is a DM Cosmic Bubble and suggest experiments, which confirm our conclusion.
基金support of this work by the National Science Foundation (CMMI Award no.1932975)。
文摘A computationally efficient two-surface plasticity model is assessed against crystal plasticity. Focus is laid on the mechanical behavior of magnesium alloys in the presence of ductility-limiting defects, such as voids. The two surfaces separately account for slip and twinning such that the constitutive formulation captures the evolving plastic anisotropy and evolving tension-compression asymmetry. For model identification, a procedure is proposed whereby the initial guess is based on a combination of experimental data and computationally intensive polycrystal calculations from the literature. In drawing direct comparisons with crystal plasticity, of which the proposed model constitutes a heuristically derived reduced-order model, the available crystal plasticity simulations are grouped in two datasets. A calibration set contains minimal data for both pristine and porous material subjected to one loading path. Then the two-surface model is assessed against a broader set of crystal plasticity simulations for voided unit cells under various stress states and two loading orientations. The assessment also includes microstructure evolution(rate of growth of porosity and void distortion). The ability of the two-surface model to capture essential features of crystal plasticity is analyzed along with an evaluation of computational cost. The prospects of using the model in guiding the development of physically sound damage models in Mg alloys are put forth in the context of high-throughput simulations.
基金Funded by Technology Innovation Demonstration Project of the Transportation Department of Yunnan Province (Science and Technology Education Section of Transport Department of Yunnan Province [2019](No.14)。
文摘The distribution characteristics of air voids in ultrathin asphalt friction course(UAFC) samples with different gradations and compaction methods were statistically analyzed using X-ray computed tomography(CT) and image analysis techniques. Based on the results, compared with the AC-5 sample, the OGFC-5mixture has a higher air void ratio, a larger air void size and a greater number of air voids, with the distribution of internal air voids being more uniform and their shapes being more rounded. The two-parameter Weibull function was applied to fit the gradation of air voids. The fitting results is good, and the function parameters are sensitive to changes in both mineral gradation and compaction method. Moreover, two homogeneity indices were proposed to evaluate the compaction uniformity of UAFC samples. Compared with the Marshall method,the SGC method is more conducive to improve the compaction uniformity of UAFC samples. The compaction method significantly influences the air void distribution characteristics and compaction uniformity of AC-5sample, but has a less significant impact on OGFC-5 sample. The experimental results in the study provides a solid foundation for further explorations on the internal structure and mixture design of UAFC.
文摘Automated X-ray defect inspection of occluded objects has been an essential topic in semiconductors,autonomous vehicles,and artificial intelligence devices.However,there are few solutions to segment occluded objects in the X-ray inspection efficiently.In particular,in the Ball Grid Array inspection of X-ray images,it is difficult to accurately segment the regions of occluded solder balls and detect defects inside solder balls.In this paper,we present a novel automatic inspection algorithm that segments solder balls,and detects defects fast and efficiently when solder balls are occluded.The proposed algorithm consists of two stages.In the first stage,the defective candidates or defects are determined through the following four steps:(i)image preprocessing such as noise removal,contrast enhancement,binarization,connected component,and morphology,(ii)limiting the inspec-tion area to the ball regions and determining if the ball regions are occluded,(iii)segmenting each ball region into one or more regions with similar gray values,and(iv)determining whether there are defects or defective candidates in the regions using a weighted sum of local threshold on local variance.If there are defective candidates,the determination of defects is finally made in the following stage.In the second stage,defects are detected using the automated inspection technique based on oblique computed tomography.The 3D precision inspection process is divided into four steps:(i)obtaining 360 projection images(one image per degree)rotating the object from 0 to 360 degrees,(ii)reconstructing a 3D image from the 360 projected images,(iii)finding the center slice of gravity for solder balls from the axial slice images in the z-direction,and getting the inspection intervals between the upper bound and the lower bound from the center slice,and(iv)finally determining whether there are defects in the averaged image of solder balls.The proposed hybrid algorithm is robust for segmenting the defects inside occluded solder balls,and improves the performance of solder ball segmentation and defect detection algorithm.Experimental results show an accuracy of more than 97%.
文摘Objective To determine the prevalence of lower urinary tract symptoms(LUTS)and their severity population in Jordan.Methods This cross-sectional survey was conducted using a paper-based survey between August and September in 2019.The study was carried out in the health care centers or hospitals in three different regions of Jordan:North(Irbid and Jarash),Middle(Amman,Madaba,Salt,and Zarqa),and South(Karak and Aqaba).Results To estimate the prevalence of LUTS,two definitions were used,including the first definition(presence of any LUTS regardless of the degree of severity)and the second definition(presence of any LUTS that occurs half the time or more).According to the first definition,1038(89.9%)reported LUTS(male:47.3%,female:52.7%),while 763(66.1%)reported LUTS according to the second definition(male:45.6%,female:54.4%).According to the International Prostate Symptom Score characterization,73.9%had nocturia and 62.9%reported daytime increased frequency.Conclusion LUTS are highly prevalent among the Jordanian population,and more than half of them have nocturia or daytime increased frequency as most frequently reported symptoms.
基金The authors would like to thank the National Natural Science Foundation of China(Nos.U2006213,42277139,42207172)the China Postdoctoral Science Foundation(No.2022M712989)the Natural Science Foundation of Shandong Province(No.ZR2022QD103).
文摘The thermal conductivity of marine sediments is an important thermophysical parameter in the study of seafloor heat flow and marine engineering construction.Understanding the effect of thermal conductivity of marine sediments in the environment has a major engineering value and theoretical significance.In this work,a modified test method was used to measure the thermal conductivity of silt in the Yellow River Delta under different void ratios,moisture contents,temperatures,and salinities.Results showed that the thermal conductivity of silt in the Yellow River Delta decreased with the increase in the void ratio and increased with the water content.Compared with sand and clay,silt in the Yellow River Delta was the least affected by the void ratio and moisture content.Under low temperatures,the heat transfer of soil was controlled by the average velocity of the phonons;therefore,the thermal conductivity of silt in the Yellow River Estuary increased with temperature.The thermal conductivity of pore water decreased with increasing salinity.Moreover,certain salinity levels resulted in a phenomenon known as the‘compressing twin electrical layer’,which led to an increase in the contact area between soil particles.With the increase in salinity,the thermal conductivity of silt in the Yellow River Delta experiences an initial decline and a subsequent increase.The proposed thermal conductivity test method is more accurate than the existing technique,and the findings provide a basis for further study on the thermal characteristics of submarine sediments.
基金supported by the National Natural Science Foundation of China(No.51888103,No.52076175).
文摘Large vertical pipes are key structures connecting subsea wells to offshore platforms.However,existing studies mainly focus on small vertical pipes.In a vertical acrylic pipe with 80 mm inner diameter and 11 m height,a high-speed camera was used to visually research the influences of pipe diameters,liquid properties and inlet effect on air-water co-flow characteristic.Different flow regime maps of vertical pipes(diameters are in the range of 50e189 mm)were compared and the critical gas velocity of the transition boundary from bubble to slug flow tended to increase with the increase of diameters at D≥80 mm.Drift-flux models were established in different flow regimes and liquid properties have a significant effect on drift coefficients of bubble flow and slug flow(void fraction a≤0.4).The influence of inlet turbulent effect on the gas-liquid interface distribution gradually weakened and disappeared from the pipe base to 85D,where the flow was fully developed.Slug frequency has a trend of increase first and then decrease with the gas Weber numbers increasing at low liquid superficial velocities(J_(L)≤0.31 m/s).And on the basis of this law,a new slug frequency correlation was proposed.It was found that there was an exponential relationship between the ratio of lengths of Taylor bubble to slug and the void fraction.
文摘The prevalent view endorses that the force of gravitation of the earth is directed towards the centre of the planet, in consequence of which, temperature and pressure at the deepest part of the planet must be very high. This view leads to the conclusion that the inner core or deepest part of the planet, though constituted of iron through which magnetic lines of force emanate, cannot be magnetic. The author has shown that amongst the earth’s three geospheres, fluid outer core that occurs between mantle and inner core, is a void zone which, because of the association of some particles from the mantle, apparently shows fluid characteristics. Occurrence of a virtually void zone in the planet’s deep interior separated by a solid mantle and iron inner core would generate a reversely directed gravitational force due to which pressure and temperature at the deepest part of the earth would be sufficiently low. Hence, the earth’s solid inner core, constituted of iron, is a dipolar permanent magnet. The paper envisages that the concept of reverse gravity presented here needs to be validated by physicists since it is an original view. The concept put forward here, not only explains the cause of earth’s magnetic phenomena, but also elucidates continental drifting and several other features of the planet in a scientifically accepted manner, thereby refuting the possibility of occurrence of convection current in the mantle which is solid and rigid.
文摘The article puts forward a hypothesis about the possibility of the existence of our Universe inside a supermassive black hole, analyzes the basic assumptions and verifiable physical consequences. The transformation of the Primary Particles obtained from the decay of Borromeo rings into binary and ternary structures is considered separately, taking into account how the percentages between Dark Matter, Dark Energy and Baryonic matter are formed. A system of kinetic equations has been compiled, which makes it possible to develop a theoretical approach to obtain these values depending on the geometric and physical characteristics of interacting particles. The possibility and necessity of the existence of a Primary Relic of Primary Particles are substantiated. The nature of the voids and the analytical solution of the Einstein equations obtained from the generalized Papapetrou solution, which leads to the existence of strings with an arbitrary distribution of matter along the string and with lengths comparable to the size of the Universe, are considered. In the case of a string of finite size and constant density, this solution leads to the well-known Weyl solution. An assumption is put forward about the existence of an Einstein-Rosen type transition, when the dimensions of the white and black holes at the ends of this transition have different dimensions.
文摘We propose that the exotic meson tetraquark u<sub>d</sub>~</sup>dũintroduced in previous papers, may be a pseudo-Goldstone boson having a tetrahedron geometry and symmetry. The transition from the neutral pion superposition of two free mesons, d<sub>d</sub>~</sup> and uũ, to the tetrahedron geometry with optional two chiral states may be the symmetry breaking of the QCD ground state. The u<sub>d</sub>~</sup>dũtetrahedron mass may be calculated by measuring the β decay rate variability. We assume that electrons and positrons are composite particle exotic tetraquarks, dũd<sub>d</sub>~</sup> for the electrons and u<sub>d</sub>~</sup>d<sub>d</sub>~</sup> for the positrons and confined by the strong force. We propose that the QCD tetrahedrons play a central role in electron pairing mechanism in both chemical bond forming and superconductor Cooper pairs. We propose a hypothesis where the QCD ground state tetrahedrons play a central role in low energy physics where quark exchange reactions between particles and the QCD tetrahedrons via gluon junctions transfer all the forces. The QCD ground state u<sub>d</sub>~</sup>dũtetrahedrons hypothesis provides a symmetry breaking and a mass gap may be created by the ground state QCD tetrahedrons Bose-Einstein condensate.
文摘As translating in most cases is considered a bicultural or even multicultural activity,cultural discrepancies and voids inevitably occur during the language decoding and encoding process of the translating.This is a heated issue that has existed for long,and translators frequently turn to two major approaches for a solutiondomestication and foreignization.However,no matter which approach a translator chooses,it is essential to make a comprehensive analysis of the cultural and influential factors that contained in the source language text,rather than simply checking through a dictionary or cyclopedia.Based on the types of culture classified by Professor Chen Hongweimaterial culture,institutional culture and mental culture,the following discussion will make an exemplification of the merits and choice between domestication and foreignization,concerning the relation between culture types and translating approaches.