X-ray diffraction study of effect of deposition conditions on α-β phase transition and stress evolution in sputter-deposited W coatings

Pure W and W-Cu-W trilayer coatings were deposited on an Fe substrate by d.c. magnetron sputtering. The α-β phase evolution, intragranular stress evolution in sputter-deposited W layer were investigated by x-ray diffraction. They are directly related to the film microstructure, density and adhesion. Therefore, control of the film stress and phase component transition is essential for its applications. The phase component transition from β-W to α-W and intragranular stress evolution from tensile to compressive strongly depend on the deposition parameters and can be induced by lowering Ar pressure and rising target power. The compressively stressed films with α-W phase have a dense microstructure and high adhesion to Fe substrate.

Corrosion resistance of electrodeposited RE-Ni-W-P-SiC composite coating

Immersion experiment results show that corrosion rate of the as deposited RE Ni W P SiC composite coating in HCl solutions increases with the rise of HCl concentration. On the contrary, the corrosion rate of the composite coating after heat treatment decreases with increasing HCl concentration. The corrosion rates of the composite coatings in as deposited state and after heat treatment in H 2SO 4 and H 3PO 4 solutions respectively decrease with the rise of H 2SO 4 and H 3PO 4 concentrations. The corrosion rate of the composite coating as deposited in FeCl 3 solutions decreases with increasing FeCl 3 concentration, while the rate of the composite coating after heat treatment increases with the rise of FeCl 3 concentration. The corrosion rate of 316L stainless steel in the corrosion media of H 2SO 4, HCl, H 3PO 4 and FeCl 3 solutions at different concentrations increases with rising concentration. In addition, the corrosion rate of 316L stainless steel in the corrosion media of H 2SO 4, HCl, H 3PO 4 and FeCl 3 solutions respectively is much greater than that of the RE Ni W P SiC composite coating as deposited and after heat treatment in the same corrosion media. [

Structure and characteristics of electrodeposited RE-Ni-W-P-B_4C-PTFE composite coatings

Hardness, friction and wear characteristics of electrodeposited RE Ni W P B 4C PTFE composite coatings were studied, and the reason for these fine characteristics was explained in respect of structure. The results show that 1) the structure of RE Ni W P B 4C PTFE composite coatings experiences a transformation process from amorphous to mixture then to crystal as the heat treatment temperature rises; 2) incorporating of B 4C greatly increases the hardness of the coating; 3) the wear resistance of the coating is best with heat treatment for 1?h at 300?℃, which is greatly superior to that of the other traditional coatings.

Corrosive-wear and Electrochemical Performance of Laser Thermal Sprayed Co30Cr8W1.6C3Ni1.4Si Coating on Ti6Al4V Alloy

Co30Cr8W1.6C3Ni1.4Si coatings were fabricated on Ti6Al4V alloy using a laser thermal spraying(LTS).The surface and cross-section morphologies,phases and bonding strength of obtained coatings were investigated using scanning electronic microscopy(SEM),X-ray diffraction(XRD),and scratch test,respectively.The effects of laser power on the coefficients of friction(COFs)and corrosive-wear behaviors of Co30Cr8W1.6C3Ni1.4Si coatings were investigated using a wear tester in 3.5%NaCl solution,and the electrochemical corrosion performance was analyzed using an electrochemical workstation.The experimental results show that the Co30Cr8W1.6C3Ni1.4Si coating is bonded with the substrate in the metallurgical form,and the bonding strengths of Co30Cr8W1.6C3Ni1.4Si coatings fabricated at the laser power of 1000,1200,and 1400 W are 76.5,56.5,and 55.6 N,respectively.The average COFs of Co30Cr8W1.6C3Ni1.4Si coatings fabricated at the laser power of 1000,1200,and 1400 W are 0.769,0.893,and 0.941,respectively;and the corresponding wear rates are 0.267×105,0.3178×105,and 0.325×105μm3/Nm,respectively,which increases with the increase of laser power,the wear mechanism is primarily abrasive wear.The corrosion potential of Co30Cr8W1.6C3Ni1.4Si coatings fabricated at the laser power of 1000,1200,and 1400 W is-0.05,-0.25,and-0.31 V,respectively,higher than-0.45 V of substrate which enhances the electrochemical corrosion resistance of substrate.

Advancing knowledge of plasma spraying coatings for Li||Sb-Sn liquid metal batteries by X-ray micro-CT

The performance of Li||Sb-Sn liquid metal batteries(LMBs) is hindered by the corrosion of the Sb-Sn cathode on its current collector. Herein, a uniform, dense, and low-oxidized W coating was prepared by plasma spraying, which can effectively resist the corrosion of the cathode and improve the cycle stability of the Li||Sb-Sn LMBs. For the first time, micro-CT nondestructive inspection is applied in the field of LMBs. The corrosion micromorphology and composition evolution of the SS304 matrix and Sb-Sn cathode with or without the plasma-sprayed W coating is obtained without disassembling the battery, which proves that the W coating can effectively protect the SS304 matrix. Our autonomous new LMB device for nondestructive inspection is universal and can be applied to different LMBs systems for advancing knowledge of corrosion mechanism and protection. This work guarantees the ability to directly visualize the inner critical positions in three dimensions and fills the knowledge gap in the field of LMB detection technology.