不同金属基体上W-C：H溅射薄膜的摩擦学性能

采用非平衡磁控溅射技术在40Cr、9Cr18、GCr15、TC4及LY12等5种金属基体上沉积了钨掺杂含氢类金刚石（W-C：H）薄膜.采用Raman光谱仪、扫描电子显微镜、纳米硬度计及纳米划痕仪分别测试了薄膜的微结构、厚度、硬度及附着力,采用球-盘摩擦试验机及光学轮廓仪分别在干摩擦和PFPE脂润滑条件下评价了5种金属材料基体上薄膜的摩擦磨损性能.薄膜性能测试结果显示,该厚度为1μm的薄膜具有典型的类金刚石结构,硬度与弹性模量分别为11.56和128.34 GPa,附着力为645 mN;摩擦试验结果显示,在干摩擦条件下几种金属基体表面W-C：H薄膜的摩擦因数和磨损率差别比较显著,而在脂润滑条件下基体材料的影响较小;与干摩擦条件相比,脂润滑条件下薄膜的磨损可减少60％ ～75％;在干摩擦与脂润滑条件下,9Cr18与40Cr基体上的W-C：H薄膜摩擦体系分别具有最小的磨损率1.71×10-7 mm3/（N·m）及4.55×10-8 mm3/（N·m）.

Growth Rate of a-Si∶H Film Influenced by Magnetic Field Gradient in MWECR CVD Plasma System

The magnetic field profiles,which are produced by three ways in the deposition chamber and plasma chamber of single coil divergent field MWECR CVD system,are investigated.The magnetic field gradient of these magnetic field profiles is obtained quantitatively by using Lorentz fit.The results indicate that the gradient value of the magnetic field profile near by the substrate,which is produced by a coil current with 137.7A if a SmCo permanent magnet is equipped under the substrate holder,is the largest;when the SmCo permanent magnet is taken away,the larger one is produced by the coil current with 137.7A and the smallest one produced by a coil current with 115.2A.High deposition rate of a-Si∶H film is observed near by the substrate with high magnetic field gradient.But uneven deposition rate along the radius of the sample holder is also found by infrared analysis technology when sample is deposited in magnetic field profile,which is produced by the coil current with 137.7A if the SmCo permanent magnet is equipped under the substrate holder.

Fabrication of Hydrogenated Microcrystalline Silicon Thin Films at Low Temperature by VHF-PECVD

Using H 2 diluted silane,series of μc Si∶H films are fabricated at low temperature with VHF PECVD.The thickness measurements reveal that the deposition rates are obviously enhanced with higher plasma excitation frequency or working pressure,but increase firstly and then decrease with the increase of plasma power density.Raman spectra show that the crystallinity and the average grain sizes of the films strongly depend on the temperature of substrate and the concentration of silane.However,the plasma excitation frequency only has effect on the crystallinity,and a maximum occurs during the further increase of plasma excitation frequency.From XRD and TEM experiments,three preferential crystalline orientations (111),(220) and (311) are observed,and the average grain sizes are different for every crystalline orientation.

Influence of Pressure on SiNx：H Film by LF-PECVD

Hydrogenated silicon nitride films as an effective antireflection and passivation coating of silicon solar cell were prepared on p-type polished silicon substrate （1.0 f^em） by direct LF-PECVD （low frequency plasma enhanced chemical vapor deposition） of Centrotherm. The preferable passivation effect was obtained and the refractive index was in the range of 2.017-2.082. The refractive index of the hydrogenated silicon nitride films became larger with the increase of the pressure. Fourier transform infrared spectroscopy was used to study the pressure influence on the film structural properties. The results highlighted high hydrogen bond and high Si-N bonds density in the film, which were greatly influenced by the pressure. The passivation effect of the films was infuenced by the Si dangling bonds density. Finally the effective minority liftetime degradation with time was shown and discussed by considering the relationship between the structural properties and passivation.

溅射靶功率对W-C:H薄膜结构与摩擦学性能的影响

目的研究不同溅射功率对W-C:H涂层结构与摩擦学性能的影响。方法用非平衡磁控溅射(UBMS)+等离子体增强化学气相沉积法(PECVD),以WC靶作为溅射靶,C2H2为反应气体,通过调制溅射靶功率,在316不锈钢与Si(100)基体上制备了W-C:H系列薄膜。通过场发射电镜(FESEM)、X射线衍射仪(XRD)、拉曼光谱对薄膜的微观结构和成分进行了表征。用UMT-3MT多功能摩擦机对薄膜的摩擦学性能进行了分析。结果 W-C主要以β-WC1-x纳米晶的形式均匀分布在非晶碳中,并表现出(200)面择优生长。随着溅射靶功率的上升,薄膜内W含量逐渐升高,(200)面衍射峰逐渐增强,sp2含量先降低后升高。靶功率在1.4 k W时具有较好的摩擦学性能,摩擦系数为0.15,磨损率为3.92×10-7 mm^3/(N·m)。结论随着溅射靶功率逐渐升高,柱状晶逐渐变粗,涂层的致密性逐渐降低,薄膜摩擦学性能与WC含量密切相关。

Influence of reaction gas flows on the properties of SiGe:H thin film prepared by plasma assisted reactive thermal chemical vapour deposition

A new preparing technology, very high frequency plasma assisted reactive thermal chemical vapour deposition （VHFPA-RTCVD）, is introduced to prepare SiGe：H thin films on substrate kept at a lower temperature. In the previous work, reactive thermal chemical vapour deposition （I^TCVD） technology was successfully used to prepare SiGe：H thin films, but the temperature of the substrate needed to exceed 400℃. In this work, very high frequency plasma method is used to assist RTCVD technology in reducing the temperature of substrate by largely enhancing the temperature of reacting gases on the surface of the substrate. The growth rate, structural properties, surface morphology, photo- conductivity and dark-conductivity of SiGe：H thin films prepared by this new technology are investigated for films with different germanium concentrations, and the experimental results are discussed.

Properties of oxide films grown on 25Cr20Ni alloy in air-H_2O and H_2-H_2O atmospheres

The oxidation kinetics,surface morphology and phase structure of oxide films grown on 25Cr20Ni alloy in air-H2O and H2-H2O atmospheres at 900 ℃ for 20 h were investigated.The anti-coking performance and resistance to carburization of the two oxide films were compared using 25Cr20Ni alloy tubes with an inner diameter of 10 mm and a length of 850 mm in a bench scale naphtha steam pyrolysis unit.The oxidation kinetics followed a parabolic law in an air-H2O atmosphere and a logarithm law in a H2-H2O atmosphere in the steady-state stage.The oxide film grown in the air-H2O atmosphere had cracks where the elements Fe and Ni were enriched and the un-cracked area was covered with octahedral-shaped MnCr2O4 spinels and Cr1.3Fe0.7O3 oxide clusters,while the oxide film grown in the H2-H2O atmosphere was intact and completely covered with dense standing blade MnCr2O4 spinels.In the pyrolysis tests,the anti-coking performance and resistance to carburization of the oxide film grown in the H2-H2O atmosphere were far better than that in the air-H2O atmosphere.The mass of coke formed in the oxide film grown in the H2-H2O atmosphere was less than 10％ of that in the air-H2O atmosphere.The Cr1.3Fe0.7O3 oxide clusters converted into Cr23C6 carbides and the cracks were filled with carbon in the oxide film grown in the air-H2O atmosphere after repeated coking and decoking tests,while the dense standing blade MnCr2O4 spinels remained unchanged in the oxide film grown in the H2-H2O atmosphere.The ethylene,propylene and butadiene yields in the pyrolysis tests were almost the same for the two oxide films.

Nanocomposite TiC/a-C：H film prepared on titanium aluminium alloy substrates by PSII assistant MW-ECRCVD

Thin films of titanium carbide and amorphous hydrogenated carbon have been synthesized on titanium aluminium alloy substrates by PSII assisted MW-ECRCVD with a mirror field. The microstructure, chemical composition and mechanical property were investigated. Using XPS and TEM, the films were identified to be a-C：H film containing TiC nanometre grains （namely, the so-called nanocomposite structure）. The size of TiC grains of nanocomposite TiC/DLC film is about 5 nm. The nanocomposite structure has obvious improvement in the mechanical properties of DLC film. The hardness of a-C：H film with Ti is enhanced to 34 G Pa~ while that of a-C：H film without Ti is about 12 G Pa, and the coherent strength is also obviously enhanced at the critical load of about 35N.

Research on the optimum hydrogenated silicon thin films for application in solar cells

Hydrogenated silicon （Si：H） thin films for application in solar ceils were deposited by using very high frequency plasma enhanced chemical vapour deposition （VHF PECVD） at a substrate temperature of about 170 ℃, The electrical, structural, and optical properties of the films were investigated. The deposited films were then applied as i-layers for p-i-n single junction solar cells. The current-voltage （I - V） characteristics of the cells were measured before and after the light soaking. The results suggest that the films deposited near the transition region have an optimum properties for application in solar cells. The cell with an i-layer prepared near the transition region shows the best stable performance.

High-Pressure Plasma Deposition of a-C:H Films by Dielectric-Barrier Discharge

The fabrication of a-C:H films from methane has been performed using dielectric-barrier discharges at atmospheric pressure. The effect of combined-feed gas, such as carbon dioxide, carbon monoxide or acetylene on the formation of a-C:H films has been investigated. It has been demonstrated that the addition of carbon monoxide or acetylene into methane leads to a remarkable improvement in the fabrication of a-C:H films. The characterization of carbon film obtained has been conducted using FT-IR, Raman and SEM.

Fabrication and characterization of iron and iron carbide thin films by plasma enhanced pulsed chemical vapor deposition

A new pulsed chemical vapor deposition（PCVD） process has been developed to fabricate iron（Fe） and iron carbide(Fe1-xCx) thin films at low temperature range from 150 ℃ to 230 ℃.The process employs bis（1,4-di-tert-butyl-1,3-diazabutadienyl）iron（Ⅱ） as iron source and hydrogen gas or hydrogen plasma as the coreactant.The films deposited with hydrogen gas are demonstrated polycrystalline with body-centered cubic Fe.However,for the films deposited with hydrogen plasma,the amorphous phase of iron carbide is obtained.The influence of the deposition temperature on iron and iron carbide characteristics have been investigated.

Study on stability of hydrogenated amorphous silicon films

Hydrogenated amorphous silicon （a-Si：H） films with high and same order of magnitude photosensitivity （-10^5） but different stability were prepared by using microwave electron cyclotron resonance chemical vapour deposition system under the different deposition conditions. It was proposed that there was no direct correlation between the photosensitivity and the hydrogen content （CH） as well as H-Si bonding configurations, but for the stability, they were the critical factors. The experimental results indicated that higher substrate temperature, hydrogen dilution ratio and lower deposition rate played an important role in improving the microstructure of a-Si：H films. We used hydrogen elimination model to explain our experimental results.

Effect of substrate temperature on the growth and properties of boron-doped microcrystalline silicon films

Highly conductive boron-doped hydrogenated mieroerystalline silicon （μc-Si：H） films are prepared by very high frequency plasma enhanced chemical vapour deposition （VHF PECVD） at the substrate temperatures （Ts） ranging from 90℃ to 270℃. The effects of Ts on the growth and properties of the films are investigated. Results indicate that the growth rate, the electrical （dark conductivity, carrier concentration and Hall mobility） and structural （crystallinity and grain size） properties are all strongly dependent on Ts. As Ts increases, it is observed that 1） the growth rate initially increases and then arrives at a maximum value of 13.3 nm/min at Ts=210℃, 2） the crystalline volume fraction （Xc） and the grain size increase initially, then reach their maximum values at TS=140℃, and finally decrease, 3） the dark conductivity （σd）, carrier concentration and Hall mobility have a similar dependence on Ts and arrive at their maximum values at Ts-190℃. In addition, it is also observed that at a lower substrate temperature Ts, a higher dopant concentration is required in order to obtain a maximum σd.

Optical Characterization of Amorphous Hydrogenated Carbon(a-C:H)Thin Films Prepared by Single RF Plasma Method

Methane （CH4） plasma was used to produce amorphous hydrogenated carbon （a- C：H） films by a single capacitively coupled radio frequency （RF） powered plasma system. The system consists of two parallel electrodes： the upper electrode is connected to 13.56 MHz RF power and the lower one is connected to the ground. Thin films were deposited on glass slides with different sizes and on silicon wafers. The influence of the plasma species on film characteristics was studied by changing the plasma parameters. The changes of plasma species during the deposition were investigated by optical emission spectroscopy （OES）. The structural and optical properties were analyzed via Fourier transform infrared （FTIR） spectroscopy, X-ray diffraction （XRD） and UV-visible spectroscopy, and the thicknesses of the samples were measured by a profilometer. The sp3/sp2 ratio and the existing H atoms play a significant role in the determination of the chemical properties of thin films in the plasma. The film quality and deposition rate were both increased by raising the power and the flow rate.

Structure and tribological properties of Si/a-C:H(Ag)multilayer film in stimulated body fluid

Si/a-C:H(Ag)multilayer films with different modulation periods are prepared to test their potential applications in human body.The composition,microstructure,mechanical and tribological properties in the simulated body fluid are investigated.The results show the concentration of Ag first decreases and then increases with the modulation period decreasing from 984 nm to 250 nm.Whereas the C content has an opposite variation trend.Notably,the concentration of Ag plays a more important role than the modulation period in the properties of the multilayer film.The a-C:H sublayer of the film with an appropriate Ag concentration(8.97 at.%)(modulation period of 512 nm)maintains the highest sp3/sp2 ratio,surface roughness and hardness,and excellent tribological property in the stimulated body fluid.An appropriate number of Ag atoms and size of Ag atom allow the Ag atoms to easily enter into the contact interface for load bearing and lubricating.This work proves that the Ag nanoparticles in the a-C:H sublayer plays a more important role in the tribological properties of the composite-multilayer film in stimulated body fluid condition.

A Comparative Study of Boron and Phosphorus Doping Effects in SiC: H Films Prepared by ECR-CVD

Hydrogenated silicon carbide films (SiC:H) were deposited using the electron cyclotron resonance chemical vapour deposition (ECR-CVD) technique from a mixture of methane, silane and hydrogen, and using diborane and phosphine as doping gases. The effects of changes in the microwave power on the deposition rate and optical bandgap were investigated, and variations in the photoand dark-conductivities and activation energy were studied in conjunction with film analysis using the Raman scattering technique. In the case of boron-doped samples, the conductivity increased rapidly to a maximum, followed by rapid reduction at high microwave power. The ratio of the photo- to dark-conductivity (σph/σd) peaked at microwave power of ~600 W. Under conditions of high microwave power, Raman scattering analysis showed evidence of the formation and increase in the silicon microcrystalline and diamond-like phases in the films, the former of which could account for the rapid increase and the latter the subsequent decrease in the conductivity.In the case of phosphorusdoped SiC:H samples, it was found that increase in the microwave power has the effect of enhancing the formation of the silicon microcrystalline phase in the films which occurred in correspondence to a rapid increase in the conductivity and reduction in the activation energy The conductivity increase stabilised in samples deposited at microwave power exceeding 500 W probably as a result of dopant saturation. Results from Raman scattering measurements also showed that phosphorus doping had the effect of enhancing the formation of the silicon microcrystals in the film whereas the presence of boron had the effect of preserving the amorphous structure.

The Effect of Pressure on the Dissociation of H_2/CH_4Gas Mixture during Diamond Films Growth via Chemical Vapor Deposition

Monte Carlo simulations are adopted to study the electron motion in the mixture of H2 and CH4 during diamond synthesis via Glow Plasma-assisted Chemical Vapor Deposition (GPCVD). The non-uniform electric field is used and the avalanche of electrons is taken into account in this simulation. The average energy distribution of electrons and the space distribution of effective species such as CH3, CH+3, CH+ and H at various gas pressures are given in this paper, and optimum experimental conditions are inferred from these results.

Carrier transport characteristics of H-terminated diamond films prepared using molecular hydrogen and atomic hydrogen

The H-terminated diamond films, which exhibit high surface conductivity, have been used in high-frequency and high-power electronic devices. In this paper, the surface conductive channel on specimens from the same diamond film was obtained by hydrogen plasma treatment and by heating under a hydrogen atmosphere, respectively, and the surface carrier transport characteristics of both samples were compared and evaluated. The results show that the carrier mobility and carrier density of the sample treated by hydrogen plasma are 15 cm^2·V^（-1）·s^（-1） and greater than 5 × 1012 cm^（-2）, respectively, and that the carrier mobilities measured at five different areas are similar. Compared to the hydrogen-plasma-treated specimen, the thermally hydrogenated specimen exhibits a lower surface conductivity, a carrier density one order of magnitude lower, and a carrier mobility that varies from 2 to 33 cm^2·V^（-1）·s^（-1）. The activated hydrogen atoms restructure the diamond surface, remove the scratches, and passivate the surface states via the etching effect during the hydrogen plasma treatment process, which maintains a higher carrier density and a more stable carrier mobility.

Structural Un-uniformity and Electrical Anisotropy of μc-Si:H Films

Structural un-uniformity and electrical anisotropy of μc-Si∶H film are investigated in this paper. It is found that the structure of μc-Si∶H film along the direction perpendicular to the substrate is not uniform, which is modulated by film thickness. In addition, there is a dark conductivity anisotropy along the direction parallel(σ∥) and perpendicular(σ⊥)to the substrate in μc-Si∶H film. The reasons for such an property of μc-Si∶H film and the effect of oxygen contamination are analyzed.

INVESTIGATION ON DEPOSITIONS AND HARDNESS CHARACTERISTICS OF a-SiC:H FILMS

In this paper, a deposition feature of a SiC:H films deposited by a RF sputtering system and a effect on the hardness of the films with various deposition conditions are investigated, and the effects of the silicon on a C:H are studied. It follows from the results that the properties of hardness can be changed with the depositing conditions. An increase of silane in the gas phase allows to deposit a SiC:H having tetrahedral structure. The sets of deposition conditions by which the different types of a SiC:H films can be deposited are obtained.