Spark plasma sintering on mechanically activated W-Cu powders

Mechanically activated W-Cu powders were sintered by a spark plasma sinteringsystem (SPS) in order to develop a new process and improve the properties of the alloy. Propertiessuch as density and hardness were measured. The microstructures of the sintered W-Cu alloy sampleswere observed by SEM (scanning electron microscope). The results show that spark plasma sinteringcan obviously lower the sintering temperature and increase the density of the alloy. This processcan also improve the hardness of the alloy. SPS is an effective method to obtain W-Cu powders withhigh density and superior physical properties.

Microstructure and Properties of W-Cu Alloys Prepared with Mechanically Activated Powder

W-15% Cu (mass fraction) alloys were sintered with mechanically activated powder in order to develop new preparing processes and improve properties of alloys. The microstructures of the activated powder and the sintered alloy were observed. Properties such as density were measured. The results show that through mechanical activation, the particle size of the powder becomes finer to sub-micron or nanometer level, some copper was soluble in tungsten, and high density W-Cu alloys can be obtained by mechanically activated powder for its action to the activation sintering.

Effect of temperature and strain rate on compressive response of extruded magnesium nano-composite

The hot deformation behaviour of extruded magnesium-zinc oxide nano composite has been studied using hot compression test.The test was conducted in the temperature range of 250-400℃ and in the strain rate range of 0.01 to 1.5 s^(−1).The processing map was obtained using the power dissipation efficiency with the functions of temperature and strain rate.The workability and instability domains were observed in the processing map for a nano composite.The optical microscopy(OM),scanning electron microscopy(SEM)and transmission electron microscopy(TEM)images were used to confirm the formation of dynamic recrystallization(DRX),dynamic recovery(DRY)and instability regions.The workability region of the composite was identified at a working temperature of 400℃ and the strain rate of 0.01 s^(−1) from the processing map.The instability regions were observed at higher strain rates(>0.1 s^(−1))and temperatures(250-400℃).

Pressure sintering of W-15wt.%Cu alloys prepared by mechanical alloying as a subsequent densification treatment method

The sintered W-15wt.%Cu alloys fabricated by mechanical alloying were re-sintered under pressure to increase the density and improve the properties of these alloys. The pressure was applied vertically along the axis of the sintered sample. Properties such as density, hardness, and bending strength were measured. The microstructures of the sintered bodies were observed. The results showed that the subsequent pressure sintering could increase the density of the sintered W-15wt.%Cu alloys. Their hardness, bending strength, and some other physical properties were also improved by this subsequent densification treatment.

Development of Flake Powder Metallurgy in Fabricating Metal Matrix Composites:A Review

Powder metallurgy （PM） is one of the most applied processes in the fabrication of metal matrix composites （MMCs）. Recently, a novel PM strategy called flake PM was developed to fabricate MMCs with nano-laminated or hierarchical architectures. The name ＂flake PM＂ was derived from the use of flake metal powders, which could benefit the uniform dispersion of reinforcements in the metal matrices and thus result in balanced strength and ductility. Flake PM has been proved to be successful in the dispersion of nano aluminum oxides, carbon nanotubes, graphene nano-sheets, and microsized B4C particles in aluminum or copper matrix. This paper reviews the technique and mechanism developments of flake PM in previous studies, and foresees the future develop of this new fabricating method.

Preparation of highly dispersed superfine W-20 wt% Cu composite powder with excellent sintering property by highly concentrated wet ball-milled process

The ball milling process and the CuWO-WOprecursors were investigated, and a new highly concentrated wet ball-milled process(HWM) was designed. W-20 wt% Cu composite powders with excellent sintering property were synthesized by highly concentrated wet ballmilled process and co-reduction. The powders were characterized by scanning electron microscopy(SEM), X-ray diffraction(XRD), field electron transmission electron microscopy(FESEM) and laser-diffraction diameter tester.The results indicate that particle size of W03-CuO powder mixtures decreases to 390 nm rapidly with the milling time increasing to 5 h. The CuWOprecursors promote the microstructural homogeneity of W and Cu. W-Cu composite powders have a highly dispersed and well sintering property. The particle size of W-Cu powders milled by HWM for 5 h is about 680 nm. High-resolution transmission electron microscopy(HRTEM) result suggests that W phase and Cu phase are mixed at nanometer scale. The above W-Cu composite powders reach the relative density of about 99.3%.