Efficient Sequestration of Congo Red Dye from Aqueous Solutions Using Pamam Dendrimer-Silica Composite

This study investigates the removal of Congo Red dye from aqueous solution using functionalized generation 3.0 and 5.0 polyamidoamine dendrimer-silica gel composite (G-3PS, G-5PS). Fourier Transform-Infra Red spectroscopy, Brunauer Emmett and Teller, Thermo Gravimetric Analysis, pH at point of zero charge, and scanning electron microscopy measurements have been applied to characterize the synthetic nanohybrid composite, these techniques revealed the successful functionalization of both dendrimer molecules and subsequent immobilization onto silica gel. The implications of varying adsorption parameters such as contact time, initial concentration of adsorbate, temperature and pH on both composites were studied. Experimental data obtained from batch adsorption processes were fitted into two equilibrium isotherms (Langmuir and Freundlich) and 3 kinetic models (Pseudo-First-Order, Pseudo-Second-Order, Intra Particle Diffusion). Adsorption mechanism was mainly governed by film diffusion due to electrostatic interactions between the functionalized dendrimer surface and Congo Red molecules. Thermodynamic parameters illustrate that the adsorption is endothermic and spontaneous. Findings suggest the Nanocomposites (G-3PS and G-5PS) are good adsorbents for the removal of Congo Red dye from aqueous solutions.

Influence of additives and concentration of WC nanoparticles on properties of WC−Cu composite prepared by electroplating

The effects of additives(polyethylene glycol(PEG),sodium dodecyl sulfate(SDS))and WC nano-powder on the microstructure,relative density,hardness and electrical conductivity of electroplated WC−Cu composite were investigated.The preparation mechanism was also studied.The microstructure of samples was analyzed by XRD,SEM,EDS,TEM and HRTEM.The synergistic effect of PEG and SDS made the WC−Cu composite more compact during the electroplating process.The hardness of WC−Cu composites increased with the increase in WC content,while the electrical conductivity decreased with the increase in WC content.The density of samples tended to increase initially and then decreased with increase in the additive content.When the electroplating solution contained 10 g/L WC nanopowder,0.2 g/L PEG and 0.1 g/L SDS,the WC−Cu composite exhibited hardness of HV 221 and electric conductivity of 53.7 MS/m.Therefore,the results suggest that WC−Cu composite with excellent properties can be obtained by optimizing the content of additives and WC particles.

Synthesis and Characterizations of Nanocrystalline WC-Co Composite Powders by a Unique Ball Milling Process

In order to explore the high efficiency of fabricating nanocrystalline WC-Co composite powders, this paper presented a unique high energy ball milling process with variable rotation rate and repeatious circulation, by which nanocrystalline WC-10Co-0.8VC-0.2Cr3C2 (wt pct) composite powders with mean grain size of 25 nm were prepared in 32 min, and the quantity of the powders for a batch was as much as 800 grams. The as-prepared powders were analyzed and characterized by chemical analysis, X-ray diffraction (XRD), transmission electron microscopy (TEM) and differential thermal analysis (DTA). The results show that high energy ball milling with variable rotation rates and repeatious circulation could be used to produce nanocrystalline WC-Co powder composites with high efficiency. The compositions of the powders meet its specifications with low impurity content. The mean grain size decreases, lattice distortion and system energy increase with increasing the milling time. The morphology of nanocrystalline WC-Co particles displays dominantiy sphere shape and their particle sizes are all lower than 80 nm. The eutectic temperature of the nanocrystalline WC-10Co-0.8VC-0.2Cr3C2 composites is about 1280℃.

Influence of tool rotation speeds on mechanical and morphological properties of friction stir processed nano hybrid composite of MWCNT-Graphene-AZ31 magnesium

The ever-increasing demand for light weighted hard materials for transportation industries encouraged researchers to develop composites with excellent mechanical properties which can transform it into more economical and eco-friendly.Reinforcing the metals with carbonaceous nanomaterials are progressively in focus due to their excellent capability to inculcate and tailor the properties of MMCs.In the present research,a hybrid nanocomposite of MWCNT-Graphene-AZ31 Mg alloy has been developed by using variable tool rotation speeds with friction stir processing(FSP).Optimized reinforcement ratio of 1.6%vol.MWCNT and 0.3%vol.of graphene have been used with variable tool rotation speeds,whereas other processing parameters are kept constant.The developed specimens were investigated using standard testing equipment for evaluating and comparing the mechanical properties on the basis of the microstructure of the processing regions and their morphological analysis,according to the ASTM standards.The obtained results revealed an improvement of 19.72%in microhardness and 77.5% of compressive strength in comparison with the base metal AZ 31 Magnesium alloy,with a tool rotational speed of 1400rpm.The values of tensile stress and percentage area reduction were recorded as less than that of the base metal matrix,but an increasing trend has been observed in the values of both with the improvement on rotational speeds of the tool.The effectual strengthening mechanisms are analyzed on the bases of SEM images and observed that discussed and found that grain refinement strengthening is the major contributor to the strength of the nanocomposite.

Powder Extrusion Molding of Nanocrystalline WC-10Co Composite Cemented Carbide

The rods that were shaped from nanocrystalline WC- 10.21 Co-0.42 VC/ Cr3 C2 （ wt% ） composite powders by using powder extrusion molding （PEM） were investigated. The nanocrystalline WC- 10.21 Co- 0. 42 VC/ Cr3 C2 （ wt% ） composite powders were prepared by the spray thermal decomposition-continuous reduction and carburization technology. In order to improve the properties of rods shaped by using powder extrusion molding, the cold isostatic pressing （CIP） technology was used before or after debinding. Specimens were siutered by vacuum siutering and hot isostatic pressing （HIP）. The density, Rockwell A hardness, magnetic coercivity , and magnetic saturation induction of siutered specimen were measured. The microstructure of the green bodies and the siutered specimens was studied by scanning electron microscopy （SEM）. Results show that the rod formed by using powder extrusion molding after debinding and followed by cold isostatic pressing can be siutered to 99.5% density of composite cemented carbide rods with an average grain size of about 200- 300 nm, magnetic coercivity of 30.4 KA / m, Rockwell A hardness of 92.6 and magnetic saturation induction of 85% . Superfine WC- 10 Co cemented carbide rods with excellent properties were obtained.

Atomic force microscope study of WC-10Co cemented carbide sintered from nanocrystalline composite powders

In order to compare the spark plasma sintedng （SPS） process plus hot isostatic press （HIP） with vacuum sintedng plus HIP, an investigation was carried out on the topography, microstructure and gain size distribution of nanocrystalline WC-10Co composite powder and the sintered specimens prepared by SPS plus HIP and by vacuum sintering plus HIP by means of atomic force microscopy （AFM）. The mechanical properties of the sintered specimens were also investigated. It is very easy to find cobalt lakes in the specimen prepared by vacuum sintering plus HIP process. But the microstructure of the specimen prepared by SPS plus HIP is more homogeneous, and the grain size is smaller than that prepared by vacuum sintering plus HIP. The WC-10Co ultrafine cemented carbide consolidated by SPS plus HIP can reach a relative density of 99.4%, and the transverse rupture strength （TRS） is higher than 3540 MPa, the Rockwell A hardness （HRA） is higher than 92.8, the average grain size is smaller than 300 nm, and the WC-10Co ultrafine cemented carbide with excellent properties is achieved. The specimen prepared by SPS with HIP has better properties and microstructure than that prepared by vacuum sintering with HIP.

CeO_(2)对WC/Ni复合熔覆层微观组织与性能的影响

本工作采用真空熔覆技术制备了不同CeO_(2)含量的WC/Ni复合熔覆层,通过SEM、XRD、EDS及显微硬度计对复合熔覆层的微观组织、成分及硬度分布等进行系统分析。结果显示:与基体呈冶金结合的复合熔覆层组织致密,复合熔覆层由厚度2~3 mm且具有网状结构特征的复合层区与约300μm的过渡层区组成,根据熔合程度过渡区又分为冶金熔合区、扩散熔合区及扩散区;随着CeO_(2)含量的增加,复合熔覆层的晶粒逐渐细化、熔合质量提高,特别是过渡熔合区出现鱼骨状的析出相;复合区的网孔部位主要组成相为γ-(Ni,Fe)固溶体、FeNi_(3)、Cr_(7)C_(3)、Cr_(23)C_(6)、Ni_(3)Si和NiB,网线区主要组成相为WC、WC_(2)、γ-(Ni,Fe)固溶体、共晶组织等;复合熔覆层的显微硬度由表面至基体逐渐降低,且随着CeO_(2)含量的增加硬度逐渐升高,CeO_(2)含量为1.5%时,达到最大值,其平均显微硬度比基体提高5~6倍。

TPU/Nano-ZnO复合改性沥青的性能研究及微观机制

为促进聚合物/纳米改性沥青在耐久性路面中的应用,在实验室将不同掺量的聚氨酯及纳米氧化锌添加到A-70#基质沥青中制备了复合改性沥青。采用传统物理性能试验、动态剪切流变试验(DSR)、弯曲梁流变试验(BBR)研究了其物理性能与流变特性,基于响应面法的优化设计来明确两种改性剂的最佳掺量。借助傅里叶红外光谱试验(FTIR)对其微观改性机理进行探讨。采用高压紫外汞灯环境箱对改性沥青进行不同时间的紫外老化,分析其抗紫外老化能力,并基于主成分分析法评价了老化性能测试指标的显著性。结果表明:聚氨酯与纳米氧化锌的共同作用提高了基质沥青的高温稳定性及低温抗裂性,两种改性剂的最佳掺量分别为5%、3%。根据FTIR结果,复合改性沥青的改性过程既存在物理共混,又有化学加成反应。聚氨酯及纳米氧化锌的加入在基质沥青紫外老化过程中能够抑制羰基、亚砜基等极性基团的生成,复数剪切模量、羰基指数、劲度模量及亚砜基指数对沥青紫外老化性能的影响最为显著。

抗菌PP/Rnano-ZnO复合材料的制备及性能研究

以棒状纳米氧化锌(Rnano-ZnO)为抗菌剂、聚丙烯(PP)为基材,采用熔融共混法在双螺杆挤出机中制备了抗菌PP/Rnano-ZnO复合材料。测试了复合材料的抗菌性能,通过DSC法研究了抗菌PP/Rnano-ZnO复合材料中Rnano-ZnO质量分数对结晶性能的影响,采用SEM分析了复合材料冲击断面的微观形貌,采用万能电子拉伸机测试了复合材料的力学性能。结果表明,抗菌PP/Rnano-ZnO复合材料中随着Rnano-ZnO的加入,结晶温度提高了1.81℃,相对结晶度提高了5.03%,冲击强度提高了47.83%,拉伸强度提高了20.96%和断裂伸长率提高了4790%;当抗菌PP/Rnano-ZnO复合材料中Rnano-ZnO质量分数为6.0%时,其力学性能、对大肠杆菌和金黄色葡萄球菌的抗菌效果最佳。

激光熔覆WC/316L复合涂层结构及磨损性能

为改善激光熔覆过程中WC增强金属基复合涂层分解与分布不均匀的问题,采用激光熔覆技术制备了50%WC含量的WC/316L复合涂层,分别采用扫描电子显微镜(SEM)、显微维氏硬度计、摩擦磨损试验机表征了熔敷层的组织形貌、硬度与摩擦磨损性能。结果显示,低热输入量可以防止WC颗粒下沉,提升熔覆层厚度方向上的WC颗粒分布均匀性;但WC的平面分布均匀性较差,同时低热输入导致WC颗粒结合较弱,易发生脱落;熔覆过程中,粉末中15%的WC发生分解。研究表明,通过降低激光热输入量,可以制备WC厚度方向较为均匀的复合涂层,提升熔覆层耐磨性,但是需要优化WC平面分布均匀性与WC颗粒结合性能。

激光能量密度对65Mn钢表面Ni60A/WC复合涂层摩擦磨损性能的影响规律

目的改善旋耕刀65Mn钢的摩擦磨损性能,提高农机触土零部件的使用寿命。方法采用激光熔覆技术在65Mn钢基体表面制备Ni60A/WC复合涂层。通过改变激光功率调节激光能量密度,在不同能量密度下制备Ni60A/WC复合涂层,观察并测试不同参数下复合涂层试样的宏观形貌、微观结构、物相组成、元素分布、显微硬度及摩擦磨损特性,研究激光能量密度对Ni60A/WC复合涂层组织演变及摩擦磨损性能的影响规律和机理。结果Ni60A/WC复合熔覆层顶部主要有胞状晶和树枝晶,分布较紧密,熔覆层中部主要有树枝状晶,熔覆层底部主要为胞状晶和垂直交界面生长的枝晶,且分布均匀致密。随着激光能量密度的升高,熔覆层的熔高和熔深增加显著,WC硬质相颗粒发生分解,硬质相的数量明显减少,涂层的平均显微硬度降低。在激光能量密度为120 J/mm^(2)时,熔覆层的平均显微硬度为587.1HV1.0,相较于基体,提升了约1.8倍。此时熔覆层的平均摩擦因数最小,为0.312,相较于基体,得到显著提升,摩擦磨损机制为轻微的磨粒磨损。经田间试验测试发现,在激光能量密度为120 J/mm^(2)时制备的带有熔覆层的旋耕刀相较于无熔覆层的旋耕刀,其磨损质量降低了63%。结论通过控制激光能量密度,可以有效调控Ni60A/WC熔覆层的硬度和耐磨性,可为农机触土易磨损件的减摩耐磨表面强化改性提供理论指导。

表面机械研磨法制备Ni+WC复合涂层的耐磨性研究

为强化TA1钛合金的组织结构并提高其耐磨损性能,采用行星式机械球磨装置,在Ni与WC 2种粉末配比分别为1∶1、2∶1、3∶1、4∶1及5∶1的5种混合型增强介质下对TA1合金进行表面机械复合强化处理,在0.05 MPa氮气气氛下,设定转速为350 r/min,时间为8 h,对TA1钛合金进行表面机械变形+固相涂层复合强化处理,这种一步法表面复合强化技术具有工艺简单、能耗少、涂层选材灵活等优势。结果显示:TA1钛合金表面形成由Ni+WC涂层+形变细晶区组成的复合强化层,涂层区厚度在40μm以上,其中Ni∶WC为3∶1时所得复合涂层内部缺陷最少,且连续均匀。在5 N、10 N载荷下Ni∶WC为3∶1摩擦系数相较于其他比例低,摩擦区间更加稳定且持续时间更长。2种载荷下磨损量均较TA1原样少,其中Ni∶WC为3∶1的强化样磨痕深度、磨损量均优异于其他4种配比,因此减摩效果最为优异。此种Ni、WC混合增强介质下表层机械复合强化工艺可大幅提升TA1钛合金表层耐磨损性。混合增强颗粒涂层具有较强的减摩效果,其磨损机制主要是磨粒磨损与氧化磨损。

冷喷涂Ti/WC复合涂层的组织与耐磨性研究

为解决钛及其合金磨损性能较差的问题,采用高压冷喷涂技术在Ti6Al4V合金基体上沉积了2种不同成分的Ti/WC复合涂层,通过室温下的干滑动摩擦磨损试验分别测试了基体与复合涂层的摩擦性能,并采用扫描电镜及拉曼光谱对磨损表面进行了观察与表征。结果表明,与Ti6Al4V基体的磨损率(4.06×10-7 mm3/(N·m))相比,复合涂层的磨损率降低了一个数量级,表现出优异的耐磨性。此外,涂层内WC含量的增加,提高了涂层的显微硬度,涂层的耐磨性也随之提升。在磨损轨迹表面,由TiO2、WO3以及WC碎片构成的摩擦膜能够有效避免磨球与涂层表面的直接接触,从而降低磨损程度。因此,冷喷涂Ti/WC复合涂层在钛合金磨损防护方面具有一定的应用前景。

Wear resistance of Zr/WC composite coatings on Cr12MoV steel surface by electric spark deposition

Zr/WC composite coating was prepared on the surface of Cr12MoV steel by electric spark deposition technology to change its surface properties. The surface and worn surface morphology of the coating were observed using scanning electron microscope. Dry friction and wear tests of the coatings were carried out at room temperature. The results show that the coating is continuous and uniform, and the thickness was about 50-60 μm. The microhardness of the coating surface was highest at 1140 HV_(200g), which was significantly higher than that of the substrate. The ear tests results show that the wear weight loss, wear volume and wear rate follow the following rules: Cr12MoV>WC coating> Zr/WC composite coating.

Characterization of cast A356 alloy reinforced with nano SiC composites

The microstructure and mechanical properties of nano composites processed via stir casting were studied. The composites were based on the A356 aluminum alloy reinforced with nano SiC particles. The density measurements show that the samples contain little porosity and the amount of porosity in the composites increases with increasing volume fraction of SiC. The microstructures of the composites were examined using optical microscope and transmission electron microscope. Microscopic observations of the microstructures reveal that the dispersion of the particles is uniform. The yield strength, ultimate tensile strength and the elastic modulus are improved with the addition of nano particles although some reduction in ductility is observed. The highest yield strength and ultimate tensile strength are obtained with the addition of 3.5% SiC nano-particles. A relatively ductile fracture in tensile fractured samples was observed by fractography examination.

Fabrication and Thermal Insulating Properties of ITO/PVB Nanocomposites for Energy Saving Glass

Chemical co-precipitation method was used to synthesize tin-doped indium oxide（ITO）nanoparticles,and the subsequent solution co-blend was employed to fabricate ITO/PVB nanocomposites.UV（Ultra-violet）-Vis（Visible）-NIR（Near Infrared） spectra show that the addition of ITO nano particles can significantly enhance the thermal insulating efficiency of ITO/PVB nanocomposites.With increasing ITO content,the thermal insulating efficiency is increased.UV is almost fully absorbed by all ITO/PVB nanocomposites.Vis transmittance-haze spectra reveal that ITO/PVB nanocomposites exhibit higher Vis transmittance over 71.3%and lower haze below 2%when ITO content is in the range of 0.1 wt%-0.7 wt%.The UV-Vis-NIR spectroscopy shows that,under the premise of over 70%transmittance to the visible light,the screening effect of the NIR can be enhanced by 80%with 0.7%ITO/PVB nanocomposite membrane compared with the undoped PVB.The thermal insulating tests indicate that,in comparison with the pure PVB film,nanocomposite films with 0.1 wt%-0.9 wt%ITO can reduce temperature by 3-8 ℃.The results show that this novel nanocomposite can be used for energy-saving glass.

Fabrication and Thermal Insulating Properties of ATO/PVB Nanocomposites for Energy Saving Glass

The pechini method was used to synthesize antimony-doped tin oxide （ATO） nanoparticles, and the subsequent solution co-blend was employed to fabricate ATO/PVB nanocomposites. Uv-Vis-NIR spectra show that the addition ofATO nano particles can significantly enhance the thermal insulating efficiency of ATO/PVB nanocomposites. With the increase of ATO content, the thermal insulating efficiency is increased. Uv is almost fully absorbed by all ATO/PVB nanocomposites. Vis transmittance-haze spectra reveal that ATO/ PVB nanocomposites exhibit higher Vis transmittance of over 72.7% and lower haze of below 2% when ATO content is in the range of 0.1 wt%-0.5 wt%. The thermal insulating tests indicate that in comparison with the pure PVB film, nanocomposite films with 0.1 wt%-0.5 wt% ATO can reduce temperature of 1-3 ℃, suggesting that this novel nanocomposite can be used for energy-saving glass.

ENHANCED MECHANICAL PROPERTIES OF POLYPROPYLENE/SILICA NANOCOMPOSITES WITH SURFACE MODIFICATION OF NANO-SILICA VIA IN SITU COPOLYMERIZATION OF METHYL METHACRYLATE AND BUTYL ACRYLATE

Nano-sized silica particles were modified with methacryloxy-propyltrimethoxysilane(MPS) followed by in situ copolymerization of methyl methacrylate(MMA) and butyl acrylate(BA).These modified nanoparticles were compounded with polypropylene(PP) to prepare PP/silica nanocomposites.PMMA grafted on nano-silica enhances the dispersion of the nanoparticles and interfacial adhesion,decreases the size of PP spherulites in nanocomposites and leads to increasing the Young's modulus and toughness of PP/silica nanocomp...

Preparation of multi-walled carbon nanotube–Fe composites and their application as light weight and broadband electromagnetic wave absorbers

Multi-walled carbon nanotube （MWCNT）-Fe composites were prepared via the metal organic chemical vapor deposi- tion by depositing iron pentacarbonyl on the surface of MWCNTs. The structural and morphological analyses demonstrated that Fe nanoparticles were deposited on the surface of the MWCNTs. The electromagnetic properties of the MWCNTs were significantly changed, and the absorbing capacity evidently improved after the Fe deposition on the MWCNT surface. A minimum reflection loss of -29.4 dB was observed at 8.39 GHz, and the less than -10 dB bandwidth was about 10.6 GHz, which covered the whole X band （8.2-12.4 GHz） and the whole Ku band （12.4-18 GHz）, indicating that the MWCNT-Fe composites could be used as an effective microwave absorption material.

DIELECTRIC PROPERTIES OF NANO Si/C/N COMPOSITE POWDER AND NANO SiC POWDER AT HIGH FREQUENCIES AND MICROSTRUCTURE CHARACTERIZATION

The dielectric properties of nano Si/C/N composite powder and nano SiC powder at high frequencies have been studied. The nano Si/C/N composite powder and nano SiC powder were synthesized from hexamethyldisilazane ((Me 3Si) 2NH) (Me:CH 3) and SiH 4 C 2H 2 respectively by a laser induced gas phase reaction. The complex permittivities of the nano Si/C/N composite powder and nano SiC powder were measured between 8 2GHz and 12 4GHz. The real and imaginary parts of the complex permittivities of nano Si/C/N composite powder are much higher than those of nano SiC powder. The SiC microcrystalline in the nano Si/C/N composite powder dissolved a great deal of nitrogen. The local structure around Si atoms changed by introducing N into SiC. Carbon atoms around Si were substituted by N atoms. So charged defects and quasi free electrons moved in response to the electric field, diffusion or polarization current resulted from the field propagation. The high ε″and loss factor tgδ(ε″/ε′) of Si/C/N composite powder were due to the dielectric relaxation.