Magnesium alloys containing rare earth elements (RE) have received considerable attention in recent years due to their high mechanical strength and good heat-resisting performance. Among them, Mg–5%Y–4%RE (WE54) mag...Magnesium alloys containing rare earth elements (RE) have received considerable attention in recent years due to their high mechanical strength and good heat-resisting performance. Among them, Mg–5%Y–4%RE (WE54) magnesium alloy is a high strength sand casting magnesium alloy for use at temperatures up to 300 ℃, which is of great interest to engineers in the aerospace industry. In the present work, the solidification behavior of Zr-containing WE54 alloy and Zr-free alloy was investigated by computer-aided cooling curve analysis (CA-CCA) technique. And the solidification microstructure and mechanical properties of them were also investigated comparatively. It is found from the cooling curves and as-cast microstructure of WE54 alloy that the nucleation temperature of α-Mg in WE54 alloy increases after Zr addition, and the as-cast microstructure of the alloy is significantly refined by Zr. While the phase constitution of WE54 alloy is not changed after Zr addition. These phenomena indicate that Zr acts as heterogeneous nuclei during the solidification of WE54 alloy. Due to refined microstructure, the mechanical properties of Zr-containing WE54 alloy is much higher than Zr-free WE54 alloy.展开更多
The coarse-grained WE54 magnesium alloy was heat treated in order to have minimum hardness minimizing the effects of precipitates and solid solution. Friction stir processing(FSP) was applied in severe conditions to o...The coarse-grained WE54 magnesium alloy was heat treated in order to have minimum hardness minimizing the effects of precipitates and solid solution. Friction stir processing(FSP) was applied in severe conditions to obtain fine, equiaxed and highly misoriented grains, with grain sizes even less than 1 μm. The high severity of processing demonstrated to have a strong impact in the microstructure. Consequently,the processed materials exhibited excellent superplasticity at the high strain rate 10^(-2)s^(-1), and temperatures between 300 and 400 ℃. The maximum tensile superplastic elongation of 756% was achieved at 400 ℃ thanks to the operation of grain boundary sliding mechanism(GBS). Besides the new data obtained through tensile testing, the paper deals with a transcendental question regarding the large differences in strain rate values at a given stress in the superplastic regime at maximum elongation compared to other magnesium-based alloys. With this is mind, 19 magnesium alloys from 22 different investigations were analyzed to give some light to this behavior that never was treated before. It is proposed that this behavior has to be attributed to the accommodation process, necessary for GBS to occur, which is hindered by reinforcing solutes.展开更多
The corrosion behavior of WE54 magnesium alloy was investigated in 3.5%NaCl aqueous solution. The electrochemical study shows that the value of corrosion potential of WE54 magnesium was -1.8V(vs SCE). In the initial s...The corrosion behavior of WE54 magnesium alloy was investigated in 3.5%NaCl aqueous solution. The electrochemical study shows that the value of corrosion potential of WE54 magnesium was -1.8V(vs SCE). In the initial stage of immersion, a kind of visible thin film, which has the appearance of artificial conversion coating by microscopy observation, formed on the surface of WE54 alloy. Through the comparison of corrosion behavior between WE54 and AZ91D, it is shown that the value of corrosion potential of WE54 is approximately 200 mV lower than that of AZ91D, and the corrosion rate of WE54 was one order smaller than that of AZ91D. After 72 h constant immersion and corrosion products removal, deeper grooves along grain boundaries was revealed but lighter corrosion was apparent on the matrix of WE54 alloy. As far as AZ91D alloy was concerned, severe localized corrosion was dominant and network-bone-like structure was remained.展开更多
In order to study the effect of Zr modification and riser size on microporosity defect distributions in WE54 alloy sand castings, the microporosity volume percentage in Zr-free and Zr-containing WE54 alloy plate casti...In order to study the effect of Zr modification and riser size on microporosity defect distributions in WE54 alloy sand castings, the microporosity volume percentage in Zr-free and Zr-containing WE54 alloy plate castings was determined by density measurement based on Archimedes＇ principle, and the microstructure of the microporosity defects was observed by optical microscopy and scanning electron microscopy. Then by using Procast software, the Niyama criterion was calculated in order to investigate the validity of Niyama criterion on prediction of microporosity defects in WE54 alloy sand castings. It is found from the density measurement results that Zr addition does not affect the microporosity distributions in WE54 alloy castings. While the distribution area of microporosity defect in the plate castings decreases significantly as the riser size increases. Based on the experimental results, a riser selection principle for production of compact WE54 alloy castings is proposed that the solidification modulus of the riser should be greater than that of the casting by 30%, simply mr ≥ 1.3mc. By comparing the experimental and simulating results, it is found that the predicted microporosity regions by Niyama criterion agrees well with experimental results, and a critical Niyama value of 0.4 ℃0.5 s0.5 mm-1 is suggested for prediction of microporosity formation in WE54 alloy sand castings.展开更多
Hot tearing is a common and severe defect occurring during solidification of castings. The rational understand- ing of hot tearing formation mechanism is beneficial to the foundry process design. In the present resear...Hot tearing is a common and severe defect occurring during solidification of castings. The rational understand- ing of hot tearing formation mechanism is beneficial to the foundry process design. In the present research, a new developed instrumented ＂CRC＂ equipment was applied in characterization of hot tearing in sand cast Mg-5 wt.% Y-4 wt.% RE （WE54） alloy with and without Zr addition. Microstructure observation and thermal analysis were carried out to help analyzing the results. The results showed that hot tearing onset occurs at a relatively low solid fraction （fs） in WE54 alloy sand castings, which indicates the participation of remaining liquid during hot tearing formation. Microstructure observation of the hot tearing surface also proves the liquid film existence between solidifying dendrites. The contraction strain caused by casting solidification induces the flowing of remaining liquid between solidifying dendrites and results in formation of interdendritic liquid films. These liquid films are separated by sufficient contraction stress and form hot cracks. The addition of Zr in WE54 alloy significantly refines the alloy microstructure and increases the solid fraction at hot tearing onset, both of which result in increasing of the fracture stress of interdendritic liquid film. Thus the hot tearing susceptibility of WE54 alloy is weakened by Zr addition.展开更多
The deformation behavior of the Mg-Y-Nd-Zr （WE54） alloy at temperatures between 25 and 400 ℃ was investigated by uniaxial and plans strain compression tests at strain rate values of 10-2 and 10^-4 s^-1. The results...The deformation behavior of the Mg-Y-Nd-Zr （WE54） alloy at temperatures between 25 and 400 ℃ was investigated by uniaxial and plans strain compression tests at strain rate values of 10-2 and 10^-4 s^-1. The results showed that the flow stress had a strong dependency on the loading condition. Yield stress and peak stress decreased with increasing deformation temperature and with decrease in the strain rate for both deformation types. The serration flow behavior was observed markedly at high temperatures and under a strain rate of 10^-4S^-1. The serration amplitude for samples deformed by plans strain compression was larger than that by uni- axial compression. Serrated flow was attributed to the interaction of dislocations with precipitates at 300 ℃ and to dynamic discon- tinuous recrystallization effects at 400 ℃.展开更多
基金This work was funded by the National Basic Research Program of China(973 Program)through project No.2013CB632202.
文摘Magnesium alloys containing rare earth elements (RE) have received considerable attention in recent years due to their high mechanical strength and good heat-resisting performance. Among them, Mg–5%Y–4%RE (WE54) magnesium alloy is a high strength sand casting magnesium alloy for use at temperatures up to 300 ℃, which is of great interest to engineers in the aerospace industry. In the present work, the solidification behavior of Zr-containing WE54 alloy and Zr-free alloy was investigated by computer-aided cooling curve analysis (CA-CCA) technique. And the solidification microstructure and mechanical properties of them were also investigated comparatively. It is found from the cooling curves and as-cast microstructure of WE54 alloy that the nucleation temperature of α-Mg in WE54 alloy increases after Zr addition, and the as-cast microstructure of the alloy is significantly refined by Zr. While the phase constitution of WE54 alloy is not changed after Zr addition. These phenomena indicate that Zr acts as heterogeneous nuclei during the solidification of WE54 alloy. Due to refined microstructure, the mechanical properties of Zr-containing WE54 alloy is much higher than Zr-free WE54 alloy.
基金Financial support from MINECO (Spain), Project MAT2015–68919-C3–1-R (MINECO/FEDER)CENIM, CSIC, for a contract funded by the aforementioned projectMINECO for a FPI fellowship, number BES2013–063963 (MINECO/FEDER/ESF)。
文摘The coarse-grained WE54 magnesium alloy was heat treated in order to have minimum hardness minimizing the effects of precipitates and solid solution. Friction stir processing(FSP) was applied in severe conditions to obtain fine, equiaxed and highly misoriented grains, with grain sizes even less than 1 μm. The high severity of processing demonstrated to have a strong impact in the microstructure. Consequently,the processed materials exhibited excellent superplasticity at the high strain rate 10^(-2)s^(-1), and temperatures between 300 and 400 ℃. The maximum tensile superplastic elongation of 756% was achieved at 400 ℃ thanks to the operation of grain boundary sliding mechanism(GBS). Besides the new data obtained through tensile testing, the paper deals with a transcendental question regarding the large differences in strain rate values at a given stress in the superplastic regime at maximum elongation compared to other magnesium-based alloys. With this is mind, 19 magnesium alloys from 22 different investigations were analyzed to give some light to this behavior that never was treated before. It is proposed that this behavior has to be attributed to the accommodation process, necessary for GBS to occur, which is hindered by reinforcing solutes.
基金Project(50574086) supported by the National Natural Science Foundation of China
文摘The corrosion behavior of WE54 magnesium alloy was investigated in 3.5%NaCl aqueous solution. The electrochemical study shows that the value of corrosion potential of WE54 magnesium was -1.8V(vs SCE). In the initial stage of immersion, a kind of visible thin film, which has the appearance of artificial conversion coating by microscopy observation, formed on the surface of WE54 alloy. Through the comparison of corrosion behavior between WE54 and AZ91D, it is shown that the value of corrosion potential of WE54 is approximately 200 mV lower than that of AZ91D, and the corrosion rate of WE54 was one order smaller than that of AZ91D. After 72 h constant immersion and corrosion products removal, deeper grooves along grain boundaries was revealed but lighter corrosion was apparent on the matrix of WE54 alloy. As far as AZ91D alloy was concerned, severe localized corrosion was dominant and network-bone-like structure was remained.
基金supported by the National Basic Research Program of China(973 Program,No.2013CB632202)
文摘In order to study the effect of Zr modification and riser size on microporosity defect distributions in WE54 alloy sand castings, the microporosity volume percentage in Zr-free and Zr-containing WE54 alloy plate castings was determined by density measurement based on Archimedes＇ principle, and the microstructure of the microporosity defects was observed by optical microscopy and scanning electron microscopy. Then by using Procast software, the Niyama criterion was calculated in order to investigate the validity of Niyama criterion on prediction of microporosity defects in WE54 alloy sand castings. It is found from the density measurement results that Zr addition does not affect the microporosity distributions in WE54 alloy castings. While the distribution area of microporosity defect in the plate castings decreases significantly as the riser size increases. Based on the experimental results, a riser selection principle for production of compact WE54 alloy castings is proposed that the solidification modulus of the riser should be greater than that of the casting by 30%, simply mr ≥ 1.3mc. By comparing the experimental and simulating results, it is found that the predicted microporosity regions by Niyama criterion agrees well with experimental results, and a critical Niyama value of 0.4 ℃0.5 s0.5 mm-1 is suggested for prediction of microporosity formation in WE54 alloy sand castings.
基金financially supported by the National Basic Research Program of China(No.2013CB632202)
文摘Hot tearing is a common and severe defect occurring during solidification of castings. The rational understand- ing of hot tearing formation mechanism is beneficial to the foundry process design. In the present research, a new developed instrumented ＂CRC＂ equipment was applied in characterization of hot tearing in sand cast Mg-5 wt.% Y-4 wt.% RE （WE54） alloy with and without Zr addition. Microstructure observation and thermal analysis were carried out to help analyzing the results. The results showed that hot tearing onset occurs at a relatively low solid fraction （fs） in WE54 alloy sand castings, which indicates the participation of remaining liquid during hot tearing formation. Microstructure observation of the hot tearing surface also proves the liquid film existence between solidifying dendrites. The contraction strain caused by casting solidification induces the flowing of remaining liquid between solidifying dendrites and results in formation of interdendritic liquid films. These liquid films are separated by sufficient contraction stress and form hot cracks. The addition of Zr in WE54 alloy significantly refines the alloy microstructure and increases the solid fraction at hot tearing onset, both of which result in increasing of the fracture stress of interdendritic liquid film. Thus the hot tearing susceptibility of WE54 alloy is weakened by Zr addition.
文摘The deformation behavior of the Mg-Y-Nd-Zr （WE54） alloy at temperatures between 25 and 400 ℃ was investigated by uniaxial and plans strain compression tests at strain rate values of 10-2 and 10^-4 s^-1. The results showed that the flow stress had a strong dependency on the loading condition. Yield stress and peak stress decreased with increasing deformation temperature and with decrease in the strain rate for both deformation types. The serration flow behavior was observed markedly at high temperatures and under a strain rate of 10^-4S^-1. The serration amplitude for samples deformed by plans strain compression was larger than that by uni- axial compression. Serrated flow was attributed to the interaction of dislocations with precipitates at 300 ℃ and to dynamic discon- tinuous recrystallization effects at 400 ℃.
