Test of membrane bioreactor for waste water treatment of a petrochemical complex

Membrane bioreactor (MBR) used in water and waste water treatment is a developing technique for water pollution control and water reuse. This paper described a membrane bioreactor for treatment of waste water in a petrochemical complex. The experimental MBR was a lab scale one composed of an activated sludge bioreactor unit and an ultrafiltration membrane unit. The relationship of COD removal with MLSS and HRT in this MBR was studied. The effects of crossflow velocity, backwash interval and volume of flush liquid on the flux were discussed. The results showed that average removal of COD, oil, SS and turbidity in petrochemical waste water by the MBR was 91%, 86%, 92% and 99%, respectively. The average removal of NH 3 N and total phosphorous was 85% and 82% respectively. A coefficient of COD removal, k , was 0017—0080 L/(mg.d). The membrane flux maintained higher than 60 L/hm 2 bar for 34 days without chemical cleaning when the velocity of crossflow was 35—39 m/s and the backwash interval was 30 minutes and backwash duration at 20 seconds. The results indicated that it is feasible for MBR technology to be used in petrochemical waste water treatment. The treated water could be considered as a source of to make up water for industrial cooling system or to be reused for other purposes.

Intended process water management concept for the mechanical biological treatment of municipal solid waste

Accumulating operational experience in both aerobic and anaerobic mechanical biological waste treatment （MBT） makes it increasingly obvious that controlled water management would substantially reduce the cost of MBT and also enhance resource recovery of the organic and inorganic fraction. The MBT plant at Gescher, Germany, is used as an example in order to determine the quantity and composition of process water and leachates from intensive and subsequent rotting, pressing water from anaerobic digestion and scrubber water from acid exhaust air treatment, and hence prepare an MBT water balance. The potential of, requirements for and limits to internal process water reuse as well as the possibilities of resource recovery from scrubber water are also examined. Finally, an assimilated process water management concept with the purpose of an extensive reduction of wastewater quantity and freshwater demand is presented.

Electrochemical Oxidation of Chlorimuron-ethyl on Ti/SnO_2-Sb_2O_5/PbO_2 Anode for Waste Water Treatment

The electrochemical oxidation of chlorimuron-ethyl on metry. The electrochemical behaviour of the electrode in a sodium Ti/SnO2-Sb2O5/PbO2 electrode was studied by cyclic voltamsulfate solution and in the mixture solution of sodium sulfate and chlorimuron-ethyl was studied. The experimental results of cyclic voltammetry show that the acidic medium was suitable for the efficient electrochemical oxidation of chlorimuron-ethyl. Some electro-generated reagent was formed in the electrolysis process and chlorimuron-ethyl could be oxidized by the electro-generated reagent. A Ti/SnO2-Sb2O5/PbO2 electrode was used as the anode and the electrolysis experiment was carried out under the optimized conditions. The electrolysis process was monitored by UV-Vis spectrometry and high performance liquid chromatography（HPLC）, and the chemical oxygen demand（COD） was determined by the potassium dichromate method. The mechanism of chlorimuron-ethyl to be oxided was studied primarily by the cyclic voltammetry and UV-Vis spectrometry. The results of electrolysis experiment demonstrate the possibility of the electrode to be used as an anode for the electrochemical treatment of chlorimuron-ethyl contained in waste water.

Overview coking plant & Lurgi gasifier plant waste water treatment

The paper described the coking plant and Lurgi gasifier plant waste water types and characteristics , comparing the COD and ammonia-N level in different source of waste water in the plant.The currently maturity coking plant waste water treatment method was statement in the paper and analyzed the pros and cons of each method.The primary cost analysis of each type of waste water treatment was also completed in the paper.According to these analyses , recommendation was prepared for coking plant and Lurgi gasifier plant waste water treatment.

A Three-Stage, Completely Sustainable Process Addressing Industrial Water Waste Treatment Management: The Case of the Sorption of Methylene Blue in Column Experiments

A detailed study regarding the optimization of a complete system for the purification of water waste is presented.Three main concerns are addressed:the nature of the absorbing material,the efficiency dependence on scale and the management of the final waste of the assembly.These three points have to be optimized in the best acceptable way from an environmental point of view.Subsequently,the wet filling material,comprised of the absorbent and the absorbed dye,was buried in dry soil,promoting soil bacterial and fungal growth.The absorbance of CO2 was determined.The use of natural vegetative material as absorbents of chemical dyes in industrial water waste is an environmentally friendly solution.Combination with the utilization of the final solid waste as fertilizer is an optimum solution,promoting sustainability within an industrial ecology framework.The adsorption column scale-up studied herein,for the removal of basic dyes from wastewaters,using methylene blue as a representative adsorbate and barley straw as a representative waste biomass adsorbent,was successful,as regards consistency and reliability(judged by low absolute and relative standard deviation)of results.

Microplastics and Wastewater Treatment Plants—A Review

The emission of microplastics into nature poses a threat to aquatic and terrestrial ecosystems. Their penetration of the food chain presents a danger to human health as well. Wastewater treatment plants can be seen as the last barrier between microplastics and the environment. This review focuses on the impact of waste treatment plants in retaining microplastics. Studies show that no wastewater treatment method leads to a complete retention of microplastics, and so wastewater treatment plants themselves are viewed as point sources for the discharge of microplastics into the aquatic environment. Problems associated with the utilization of microplastic loaded sewage sludge are also discussed in the review.

Industrial Wastewater Treatment by Using MBR (Membrane Bioreactor) Review Study

This study demonstrated the importance, process, activation and applications of Membrane in bioreactor to treat the waste water. Membrane Bioreactor (MBR) process consists of a biological reactor integrated with membranes that combine clarification and filtration of an activated sludge process into a simplified, single step process. Operating as an MBR allows conventional activated sludge plants to become single step processes, which produce high quality effluent potentially suitable for reuse. Application of MBR technology for industrial wastewater treatment has also gained attention because of the robustness of the process. Theoretically, maintenance of long SRT in MBR is in favor of the retention and development of special microorganisms, which may lead to better removal of refractory organic matter and make the system more robust to load variations and toxic shocks. Literature suggested the conceptual expectation of enhanced biodegradation of hardly biodegradable compounds in MBR does not often come true. Improved biodegradation to certain extent has been reported in a few studies;however the underlying factors leading to such improvement still remains to be elucidated. This is comprehensive review of the studies dealing with recalcitrant industrial wastewater treatment by MBR, and casts light on the strategies to achieve enhanced biodegradation of hardly biodegradable industrial pollutants in MBR.

Swedish Experience and Excellence in Wastewater Treatment Demonstrated Especially in Phosphorus Removal

Water quality protection in Sweden has a more than 80-year history. The needed knowledge has by large been imported. Now, to some extent the development of phosphorus removal technology may be Swedish contribution to advanced knowledge. This paper presents the development in Sweden, mainly a close to 50-year period. Starting in the late 1960s, a standard of <0.5 mg P/l was the normally raised effluent criteria, regardless of the magnitude of the discharge flow. The successive sharpening of the discharge levels has today resulted in a level of 0.2 to 0.3 mg P/l typically. As a matter of fact, even levels of 0.1 to 0.15 mg P/l have been discussed. The period should a large extent demonstrated both improved technologies and a far better efficiency with respect to the use of chemicals and energy. Some important points in this development may be the understanding of the Oxygen Consumption Potential, as well as the identified needs for an improved nitrogen removal. Lately the problems of complex pollution agents and predominantly the remains of pharmaceutical agents have been identified. To illustrate the development during the 50-year period, two examples are presented from the Swedish context. The main conclusion in this paper is that the Swedish history on phosphorus removal illustrates how empirical science in practice sometimes works, including a never-ending need for an open mind and a readiness to take revised and improved knowledge on board.

Impact of <i>Moringa oleifera</i>Cake Residue Application on Waste Water Treatment: A Case Study

Most of water treatments require higher expenditure. Chemical coagulant requires higher cost and has some drawback after treatment such as pH changes. Moringa oleifera cake residue (MOCR) is one of the alternatives to replace chemical coagulant. A jar test apparatus was used to monitor water treatment. Water quality of Gebeng River (GR) and waste water (WW) was examined before and after treatment. Different parameters using (MOCR) was investigated. Preliminary laboratory results showed the great potential of the (MOCR) to be used in water treatment. MOCR shows an excellent reduction in turbidity (97 % was removed). The bacteria were reduced from 1.7 × 105 to 8 × 103 CFU/ml. Dissolved oxygen (DO) was improved that elevated from 1.06 ± 0.04 to 5.09 ± 0.03 mg/L. However, chemical oxygen demand (COD) and biological oxygen demand (BOD) were increased from 520.5 ± 0.71 to 865.0 ± 2.12 mg/L and from 120.5 ± 2.12 to 270.5 ± 2.12 mg/L respectively. Nevertheless, there is no significant alteration of pH, conductivity, salinity and total dissolved solid (TDS) after treatment. The iron (Fe) was fully removed while copper (Cu) and cadmium (Cd) were successfully removed up to 98%. The reduction of lead (Pb) also achieved 82.17%. Also, (MOCR) can be stored for long time up to 6 months without affecting the biological properties of MO.

Performance Simulation of H-TDS Unit of Fajr Industrial Wastewater Treatment Plant Using a Combination of Neural Network and Principal Component Analysis

Nowadays, with regard to environmental issues, proper operation of wastewater treatment plants is of particular importance that in the case of inappropriate utilization, they will cause serious problems. Processes that exist in environmental systems and environmental engineers are dealing with them mostly have two major characteristics: they are dependent on many variables;and there are complex relationships between its components which make them very difficult to analyze. Being familiar with characteristics of industrial town effluents from various wastewater treatment units, which have high qualitative and quantitative variations and more uncertainties compared to urban wastewaters, plays very effective role in governing them. In order to achieve a better and efficient control over the operation of an industrial wastewater treatment plant, powerful mathematical tool can be used that is based on recorded data from some basic parameters of wastewater during a period of treatment plant operation. In this study, the multilayer perceptron (MLP) feed forward neural network with a hidden layer and stop training method was used to predict quality parameters of the industrial effluent. Data of this study are related to the Fajr Industrial Wastewater Treatment Plant located in Mahshahr—Iran that qualitative and quantitative characteristics of its units were used for training, calibration and evaluation of the neural model. Also, Principal Component Analysis technique was applied to modify and improve performance of generated models of neural networks. The results of this model showed good accuracy of the model in estimating qualitative pro- file of wastewater. This model facilitates evaluating the performance of each treatment plant units through comparing the results of prediction model with the standard amount of output.

Feasibility Study for Self-Sustained Wastewater Treatment Plants—Using Biogas CHP Fuel Cell, Micro-Turbine, PV and Wind Turbine Systems

This paper studies the application of renewable energy sources in wastewater treatment plants to achieve self-sustain- ability of power. The data of wastewater treatment plant in the rural city of Toukh-EGYPT are presented as a case-study. The primary objective is to provide an entirely renewable standalone power system, which satisfies lowest possible emissions with the minimum lifecycle cost. Mass balance principle is applied on the biodegradable components in the wastewater to evaluate the volume of digester gas that is produced from sludge through anaerobic digestion process. Using digester gas as a fuel lead to study combined-heat-and-power technologies, where fuel cell is selected in order to abide by the low emissions constraint. The study assessed the electrical power obtained from fuel cell and the utilization of the exhausted heat energy for additional electrical power production using a micro-turbine. After covering the major part of load demand, the use of other renewable energy sources was studied. The strength of both solar and wind energy was determined by the case-study location. Hybrid optimization model for electric renewable (HOMER) software was used to simulate the hybrid system composed of combined-heat-and-power units, wind turbines and photovoltaic systems. Simulation results gave the best system configuration and optimum size of each component beside the detailed electrical and cost analysis of the model.

PREPARATION AND APPLICATION OF COPOLYMERS OF 2-ACRYLAMIDO-2-METHYL PROPANE SULFO ACID AS WASTE WATER TREATMENT AGENTS

In this paper, the preparation and application of copolymers of 2-acrylamido-2-methyl propane sulfo acid (AMPS) were discussed. The results showed that the copolymers with molecular weight 18.10 million can be prepared. In treating waste water from deinked pulp, the dosage of copolymers was 0.75ppm, the optimum dosage of PAC was 100ppm; dosage of the amphoteric polyacylamide (AmPAM) with molecular weight 11.34 million was 0.75ppm, the optimum dosage of PAC was 75ppm. The removed rate of CODcr was above 70%.

Troubleshooting and Optimization of High-Strength Inhibitory Chemical Wastewater Treatment Process

从化学工业的废水通常具有高张力并且可以包含是的次要的禁止、不顺从的 organics 有时，不乐意地， identifiable.Thispaper 描述处理 43000 mg 中心点L~的 CODconcentration 的生物废水处理植物( WWTP )的经验(从含氧化学药品的 manufacturingplant.Stage 的-1)废水改进由导致 synergistic 进程的化学废水流完成的禁止的流入的使用其它的冲淡的植物过程，和由经由使发酸的析相作用的禁止的 organics 的移动，生产一条高质量的自河的有效地完成的进程优化。特别地，粒状淤渣的货到付款移动效率基于从 56% ～ 90%.The 期末考试自河货到付款增加的厌氧的反应堆从 250mg 中心点 L~ 减少了(-1) to50mg 中心点 L^(-1),consistently 遇见 l00 mg 中心点 L~ 的 COD 集中(-1)regulatory 分泌物限制。进程改进的成功在生物进程作为底层禁止者支持假设 thatlong 链 quaternary 羧酸行为。

Synthesis and Application of Granular Activated Carbon from Biomass Waste Materials for Water Treatment:A Review

There is an increased global demand for activated carbon(AC)in application of water treatment and purification.Water pollutants that have exhibited a greater removal efficiency by AC included but not limited to heavy metals,pharmaceuticals,pesticides,natural organic matter,disinfection by-products,and microplastics.Granular activated carbon(GAC)is mostly used in aqueous so-lutions and adsorption columns for water treatment.Commercial AC is not only costly,but also obtained from non-renewable sources.This has prompted the search for alternative renewable materials for AC production.Biomass wastes present a great potential of such materials because of their availability and carbonaceous nature.This in turn can reduce on the adverse environmental effects caused by poor disposal of these wastes.The challenges associated with biomass waste based GAC are their low strength and attrition resistance which make them easily disintegrate under aqueous phase.This paper provides a comprehensive review on recent advances in production of biomass waste based GAC for water treatment and highlights future research directions.Production parameters such as granulation conditions,use of binders,carbonization,activation methods,and their effect on textural properties are discussed.Factors influencing the adsorption capacities of the derived GACs,adsorption models,adsorption mechanisms,and their regeneration potentials are reviewed.The literature reveals that biomass waste materials can produce GAC for use in water treatment with possibilities of being regenerated.Nonetheless,there is a need to explore 1)the effect of preparation pathways on the adsorptive properties of biomass derived GAC,2)sustainable production of biomass derived GAC based on life cycle assessment and techno-economic analysis,and 3)adsorption mechanisms of GAC for removal of contaminants of emerging concerns such as microplastics and unregulated disinfection by-products.

Production of solid fuels by hydrothermal treatment of wastes of biomass,plastic,and biomass/plastic mixtures:A review

Traditional disposal methods of biomass and plastic waste,such as landfill,combustion,and compost,no longer meet the requirements of carbon reduction,carbon neutrality,and sustain-able society due to low utilization efficiency and severe pollution.As a green,efficient and environmentally-friendly method,hydrothermal technology has been paid much attention to and has already been applied to recycle or reuse various plastic and biomass wastes.No matter for the single or mixed type of waste,it is expected to achieve efficient recycling and obtain value-added products through the hydrothermal process.This review summarized the basic knowledge of hydrothermal technology and the possible reaction mechanism of biomass and plastics un-der hydrothermal conditions and listed the previous reports on the application of hydrothermal technology for converting wastes of biomass,plastic,and biomass/plastic mixtures to solid fuels.Moreover,regarding the future of hydrothermal technology,four points related to reaction mech-anism,synergistic effect,catalysis,and scaled-up application,were provided for consideration.

Recycling water glass from wet reclamation sewage of waste sodium silicate-bonded sand

Wet reclamation of waste sodium silicate-bonded sand produces much alkaline sewage and causes pollution. Recycling water glass from wet reclamation sewage of the waste sodium silicate-bonded sand can solve pollution issues and generate economic benefits. In this work, the wet reclamation sewage was filtered, and the filtrate was causticized with a quicklime powder to produce a lye. The effects of causticization temperature, causticization time, and the amount of quicklime powder on the causticization rate were studied. The lye was used to dissolve the silica in the filtration residue to prepare a sodium silicate solution. The effects of the mass of filtration residue, dissolution temperature, and dissolution time on sodium silicate modulus were studied. Finally, the recycled water glass was obtained by concentrating the sodium silicate solution, and the bonding strength of the recycled water glass was tested. The results showed that the causticization rate could be improved by increasing the amount of quicklime powder, causticization temperature, and causticization time, and the highest causticization rate was above 92%. Amorphous silica in the filtration residue dissolved in the lye. Increasing the amount of the filtration residue, dissolution temperature, and dissolution time could improve the sodium silicate modulus. The bonding strength of the recycled water glass was close to that of commercial water glass. The recycled water glass could be used as a substitute for the commercial water glass.

Pytoremediation of fluoroquinolone group of antibiotics from waste water

The study involved selection of wetland plant species hyper efficient in removing fluoroquinolone group of antibiotics so that they can be used in a constructed wetland system patented by NEERI, India (European Patent Office (EPO) Pub. No.: WO2004087584) or any other constructed wetland. Phyto removal of these antibiotics at such high concentrations without any toxic effect on the plant species is very useful as incomplete removal of certain antibiotics such as Ciprofloxacin, and Ofloxacin from waste waters is of concern due to their health effects if they do persist in finished waters even at ng/l levels. Five different wetland plant species which were also tested for their efficiency to treat municipal wastewater were used to test their efficiency to scavenge commonly used fluoroquinolone antibiotics (which are not degraded easily) namely Ciprofloxacin, Gemifloxacin mesylate, Ofloxacin and Gatifloxacin from aqueous medium (Hoagland-Arnon solution). EC double beam UV-VIS spectrophotometer was used to obtain lambda max of Ciprofloxacin, Gemifloxacin mesylate, Ofloxacin and Gatifloxacin in Hoagland-Arnon solution. The most efficient plant species for each antibiotic were selected and tested again for confirmation of antibiotic removal efficiency at a high concentration of 50 mg/l of each antibiotic. Taxodium distichum was found to be the most suitable for the removal of Ofloxacin, Gatifloxacin and Ciprofloxacin showing maximum removal of 32 mg/l (on 6th day), 21 mg/l (on 8th day), 32 mg/l (on 9th day), respectively and Canna indica was found to be the most suitable for removal of Gemifloxacin mesylate showing maximum removal of 38 mg/l (on 8th day).

ZnO的绿色合成及光催化降解模拟废水研究

以甘露醇为模板剂,通过绿色合成途径,分别采用化学沉淀法和水热合成法制备ZnO。使用X-射线粉末衍射仪(XRD)和扫描电子显微镜(SEM)对样品的结构和形貌进行表征,用亚甲基蓝模拟工业废水中的有机污染物,对ZnO样品光催化降解模拟废水的性能进行研究。实验结果表明,2种方法合成的样品均为分散程度较好的六方纤锌矿结构,ZnO样品微粒尺寸随甘露醇用量的增加而减小。通过化学沉淀法得到的ZnO样品表面呈蚕蛹状且内部中空,通过水热合成法得到的ZnO样品呈牡丹花状。以甘露醇为模板制得的ZnO样品均能有效降解亚甲基蓝,催化降解反应符合准一级反应动力学特征。