High Water Resistance and Enhanced Mechanical Properties of Bio-Based Waterborne Polyurethane Enabled by in-situ Construction of Interpenetrating Polymer Network

In this study,acrylic acid was used as a neutralizer to prepare bio-based WPU with an interpenetrating polymer network structure by thermally induced free radical emulsion polymerization.The effects of the content of acrylic acid on the properties of the resulting waterborne polyurethane-poly(acrylic acid)(WPU-PAA)dispersion and the films were systematically investigated.The results showed that the cross-linking density of the interpenetrating network polymers was increased and the interlocking structure of the soft and hard phase dislocations in the molecular segments of the double networks was tailored with increasing the content of acrylic acid,leading to enhancement of the mechanical properties and water resistance of WPU-PAA films.Notably,with the increase in content of acrylic acid,the tensile strength,Young’s modulus,and toughness of the WPU-PAA-110 film increased by 3 times,and 8 times,and 2.4 times compared with WPU-PAA-80,respectively.The WPU-PAA-100 film showed the best water resistance,and the water absorption rate at 96 h was only 3.27%.This work provided a new design scheme for constructing bio-based WPU materials with excellent properties.

Effects of H_3PO_4 and Ca(H_2PO_4)_2 on mechanical properties and water resistance of thermally decomposed magnesium oxychloride cement

The effects of H3PO4 and Ca（H2PO4）2 on compressive strength, water resistance, hydration process of thermally decomposed magnesium oxychloride cement （TDMOC） pastes were studied. The mineral composition, hydration products and hydration heat release were analyzed by XRD, FT-IR, SEM and TAM air isothermal calorimeter, etc. After being modified by H3PO4 and Ca（HzPO4）2, the properties of the TDMOC are improved obviously. The compressive strength increases from 14.8 MPa to 48.1 MPa and 37.1 MPa, respectively. The strength retention coefficient （Kn） increases from 0.38 to 0.99 and 0.94, respectively. The 24 h hydration heat release decreases by 10% and 4% and the time of hydration peak appearing is delayed from 1 h to about 10 h. The XRD, FT-IR and SEM results show that the main composition is 5Mg（OH）z＇MgCIz＇8H20 in the modified TDMOC pastes. The possible mechanism for the strength enhancement was discussed. The purposes are to extend the potential applications of the salt lake magnesium resources and to improve the mechanical properties of TDMOC.

INFLUENCE OF SILOXANE CO-SEGMENT LENGTH AND CONTENT OF WATERBORNE POLYSILOXANE-URETHANE COPOLYMERS ON THEIR WATER RESISTANCE,THERMAL STABILITY AND MECHANICAL PROPERTIES

A series of stable waterborne polysiloxaneurethane （WPSUR） dispersions were prepared using amino-terminated polydimethylsiloxane （NS）, dimethylolpropionic acid （DMPA）, castor oil, polypropylene glycol and toluene diisocyanate. Meanwhile, NS with different molecular weights was synthesized and used as the soft co-segment. Effects of types and contents of soft co-segments as well as chain extenders on the thermal degradation and stability for WPSUR films were examined. Results reveal that WPSUR films exhibit excellent water resistance and mechanical properties as compared with pure polyurethane （PU） films, and the NS soft co-segment possesses a remarkable effect on the second stage （stage Ⅱ）, while the content of the hard segment is propitious to the initial stage （stage Ⅰ）. Moreover, the highest temperature of stage Ⅱ （T2m） for WPSUR films using NS as soft co-segment is 413℃, approximately being 30℃ higher than that of those typical PUs using HDA and APDMS as the chain extenders, respectively.

Enhanced Water Resistance Performance of Castor Oil—Based Waterborne Polyurethane Modified by Methoxysilane Coupling Agents via Thiol-Ene Photo Click Reaction

Nowadays,waterborne polyurethanes(WPUs)prepared from renewable resources has attracted more and more attention.However,due to its structure,the prepared films easily swells in water and greatly affects the application range of WPUs.Therefore,solving the problem of water resistance is a way to improve the application range of WPUs.In this study,a series of WPU dispersions were prepared using castor oil as the bio-based polyol.Besides,the thiol-ene photo click reaction was carried out on the WPU films for silane modification.The effect of the silane modification on the chemical structures of the WPU dispersions and the properties of the WPU films was investigated and discussed.The results revealed that the WPU dispersions had a smaller particle size and potential,showing excellent stability.In addition,the modified WPU films showed highly water resistance which 72 h water absorption could be reduced to 1.94%and the contact angle was up to 99.34?.Moreover,the modified WPU films also exhibited excellent solvent resistance(in acid and salt solution)and thermal stability.This study can provide a new way to improve the water-resistance,hydrophobicity,and thermal stability of bio-based waterborne polyurethane for potential application in painting,adhesives and inks.

Allyl Glycidyl Ether-modified Animal Glue Binder for Improved Water Resistance and Bonding Strength in Sand Casting

This paper aims to develop a modified animal glue sand binder for foundry casting with improved water resistance and bonding strength.An efficient method is reported by using sodium hydroxide as the catalyst to improve the operability of animal glue binder and allyl glycidyl ether as the modifier to improve the water resistance and bonding strength.Sand specimens prepared using allyl glycidyl ether-modified animal glue binder were cured by compressed air at room temperature.The proposed method saves energy and is environmentally friendly and inexpensive.Compared with unmodified animal glue binder,standard dog bone sand specimens with allyl glycidyl ether-modified animal glue binder had higher tensile strength of 2.58 MPa,flowability of 1.95 g,better water resistance(a lower decrease in tensile strength at 25°C and relative humidity of 60%),and good collapsibility.This allyl glycidyl ether-modified animal glue binder is suitable for practical application in the foundry industry.

The Impact and Intervention of Handheld Tai Chi Water-Resistance Fitness Ball on Middle-Aged and Elderly Patients with Parkinson’s Disease

Through the use of a survey and statistical methods, this study explores the effects and interventions of handheld Tai Chi water resistance fitness balls on the elderly with Parkinson’s disease. Firstly, a questionnaire on exercise compliance for patients with Parkinson’s disease was developed, and its reliability and validity were tested. Then, a survey was conducted to investigate the current status of exercise compliance among Parkinson’s disease patients, including general information, scoring status, and single and multiple factor analyses of influencing factors [1]. The results of the study show that through qualitative research, the dimensions and item pools of the questionnaire were initially constructed, and the reliability analysis of the questionnaire was conducted through Delphi expert consultation, with favorable results in terms of its reliability and validity [2]. Regarding the current status of exercise compliance among Parkinson’s disease patients, the study found that the level of exercise compliance needs improvement, and there are significant differences in exercise compliance levels among patients under different circumstances. Finally, the research results were discussed and conclusions were drawn. The innovation of this study lies in the development of a questionnaire on exercise compliance for patients with Parkinson’s disease and the preliminary qualitative research and Delphi expert consultation conducted on it, providing new ideas and methods for the study of exercise compliance. However, the study also has limitations as it did not examine the effects of other interventions on Parkinson’s disease, so further research should be conducted [3].

RESEARCH ON THE WATER-RESISTANCE OF MAGNESIUM OXYCHLORIDE CEMENT——I:THE STABILITY OF THE REACTION PRODUCTS OF MAGNESIUM OXYCHLORIDE CEMENT IN WATER

In this paper .the change of the crystalline phases in hardened magnesium oxychloride cement (MOC) paste in mater was analyzed by XRD. It was developed that the reaction products 5 phase or 3 phase of MOC are instable in water and can be changed into Mg(OH)2 by the action of water, which causes the content of 5 phase or 3 phase to be less and less,the content of Mg(OH)2 to be more and more and the strength to be the lower the lower,after hardended MOC paste was immersed in water. The change of 5 pliase and 3 phase into Mg(OH)2 is not a dissolve process, but a hydrolysis process. The hydrolysis products of 5 phase and 3 phase are Mg(OH)2 precipitation and soluble Cl-,AIg+ ions and H2O. The hydrolysis is sponta-neous thermodynamically and its chemical kinatic equation is C = C,,e-k Thus .it is suggested that only by enhancing the stability of 5 phase or 3 phase in water and preventing 5 phase or 3 phase from the hydrolyzing can the water resistance of MOC be improved well.

Simultaneous Improvement in the Flame Retardancy and Water Resistance of PP/APP through Coating UV-curable Pentaerythritol Triacrylate onto APP

To improve the flame-retardant efficiency and water resistance of ammonium polyphosphate（APP）, the UV-curable pentaerythritol triacrylate（PETA） was used to microencapsulate APP via the UV curing polymerization method. The prepared PETA-microencapsulated APP（PETA-APP） was characterized by Fourier transform infrared spectroscopy（FTIR）, scanning electron microscopy（SEM）, and thermogravimetric（TG） analysis. PETA-APP was used as intumescent flame retardant（IFR） alone to flame retard polypropylene（PP）. The water resistance of PP/PETA-APP composites was investigated, and the effect of PETA on the combustion behaviors of PP/APP composites was studied through limiting oxygen index（LOI）, vertical burning test（UL-94） and cone calorimeter（CC） test, respectively. With 40 wt% of PETA-APP, the PP/PETA-APP system could achieve a LOI value of 30.0% and UL-94 V-0 rating after treatment in hot water for 168 h, while the LOI value of the system containing 40 wt% uncoated APP was only 19.2%, and it failed to pass the UL-94 rating. CC test results showed that the heat release rate（HRR）, mass loss rate（MLR） and smoke production rate（SPR） of PP/PETAAPP system decreased significantly compared with PP/APP system, especially the peak of HRR was decreased by 51.4%. The mechanism for the improvement of flame reatardancy for PP/PETA-APP composites was discussed based on FTIR and X-ray photoelectron spectroscopy（XPS） tests. All these results illustrated that simultaneous improvement of flame retardancy and water resistance for PP/APP was achieved through coating UV-curable PETA onto APP.

Water and Oil Resistance of Special Paperboard for Petroleum Packaging

The influence of different coating formulas and times on the water and oil resistance of paperboard was studied. The water and oil resistance of paperboard coated with a modified butadiene-styrene copolymer latex and fluorinated anion grease-proof agent was better than that coated with modified butadiene-styrene copolymer latex,where the modified butadiene-styrene copolymer latex was used as the pre-coating substrate and the F1516 fluorinated grease-proof agent was used as the top coating material. By coating modified butadiene-styrene copolymer latex with 30% solid content and F1516 fluorinated grease-proof agent with 24% solid content,the oil resistance of paperboard could reach anti-oil grade 12 and the water resistance could increased by98. 64%( compared with the base paperboard without any coating treatment).

Synthesis of a Novel Core-shell Type Acrylic-polyurethane Hybrid Emulsion Containing Siloxane and Fluorine as well as Water and the Oil Resistances of Cured Film

Siliconated polyurethane （Si-PU） was synthesized using isophorone diisocyanate （IPDI）, hydroxybutyl-terminated polydimethylsiloxane （PDMS）, polytetramethylene ether glycol （PTMG）, polypropylene glycol （PPG）, 1,6-hexanediol （HDO）, dimethylol propionic acid （DMPA） and triethylamine （TEA）. Based on butyl acrylate （BA）, 2, 2, 2-trifluoroethylmethacrylate （TFEMA） and Si-PU as a seed emulsion, a novel core-shell type acrylic-polyurethane hybrid emulsion, containing siloxane and fluorine （F-Si-PU）, was prepared by seeded emulsion polymerization. The contents of siloxane and fluorine were determined according to the feed ratio. Fourier transform infrared spectroscopy （FTIR） was used to identify the chain structures of Si-PU and F-Si-PU. Investigation of transmission electron microscopy （TEM） confirmed the core-shell structure of F-Si-PU emulsion. Measurement results of water contact angle and the swelling ratio in water and n-octane for cured film showed that the water and the oil resistances for F-Si-PU had been significantly improved at a suitable content of fluorine and siloxane.

The Mixed-Alkali Effect on The Resistance of Glass to Water

Based on the composition of float glass, the resistance of glassto water, in which a small amount of K_2O(0-1.0 wt/100)wassubstituted for equivalent amount of Na_2O, was investigated by meansof glass grains testing. The components extracted from the glass andtotal alkalinities in extraction solution were de- termined by atomicabsorption spectroscopy and neutralizing method, respectively. Thecomposition of the glass was 14.4 K_2O+ Na_2O, 4.0 MgO, 8.2 CaO, 1.4Al_2O_3, 72.0 SiO, and the minimum extraction radio of oxides(maximum durability)occurred at a K_2O/Na_2O radio of 0.051(byweight)due to the presence of the mixed- alkali effect.

Preparation of Environmentally Friendly Urea-Hexanediamine-Glyoxal(HUG)Resin Wood Adhesive

Using non-toxic,low-volatile glyoxal to completely replace formaldehyde for preparing urea-glyoxal(UG)resin adhesive is a hot research topic that could be of great interest for the wood industry.However,urea-glyoxal(UG)resins prepared by just using glyoxal instead of formaldehyde usually yields a lower degree of polymerization.This results in a poorer bonding performance and water resistance of UG resins.A good solution is to pre-react urea to preform polyurea molecules presenting already a certain degree of polymerization,and then to condense these with glyoxal to obtain a novel UG resin.Therefore,in this present work,the urea was reacted with hexamethylene diamine to form a polyurea named HU,and then this was used to react it with different amounts of glyoxal to synthesize hexamethylenediamine-urea-glyoxal(HUG)polycondensation resins,and to use this for bonding plywood.The results show that the glyoxal can well react with HU polyuria via addition and schiff base reaction,and also the HUG resin exhibits excellent bonding strength and water resistance.The shear strength of the plywood bonded with this HUG at 160°C hot press temperature as high as 1.93 MPa,2.16 MPa and 1.61 MPa,respectively,which meets the requirement of the China national standard GB/T 9846-2015(≥0.7 MPa),and can be a good choice as a wood adhesive for industrial application.

Influence of Fly Ash and Silica Fume on Water-resistant Property of Magnesium Oxychloride Cement

By incorporation of fly ash or silica fume into magnesium oxychloride （MOC） cement, a high water resistance material can be formed for successful industrial applications. The influences of fly ash and silica fume on water-resistant property were investigated by SEM and EDS. It is found that the incorporation of fly ash or silica fume can improve the water-resistance of the MOC. The improvement of the water resistance of the MOC incorporated with fly ash or silica fume may be attributed to the alumino-silicate 5·1·8 gel or silicate 5·1·8 gel.

Water resistant features of high-risk outburst coal seams and standard discriminant model of mining under water-pressure

It is important to emphasize the value of research in safe mining technology of high-risk water outburst coal seams. We describe briefly current conditions abroad and in China. Based on an Ordovician limestone aquifer with high-risk water outburst seams in the Feicheng coal field, we analyzed the water-resistant characteristics of a coal floor aquifuge and the behavior of water head intrusion of a confined aquifer and propose a safe criterion model and relevant technology of mining above aquifers. This has brought satisfactory results in engineering practice.

Starch Grafted Water Resistant Polyvinyl Acetate-Based Wood Adhesive: A Review

Global energy issues and the reliance on hydrocarbon resources have resulted in the reduction of petroleum sources, and the focus of the chemical industries has shifted to substitute raw material sources. The major raw materials used in wood adhesives, such as hydrocarbons like polyvinyl acetate, would be gradually replaced by renewable natural polymers. Currently, polyvinyl alcohol has the limitation of petroleum origin, which is non-economical and it will be replaced by biopolymers. Conventionally available wood adhesive emulsions are colloid-like polyvinyl alcohol stabilized. Starch, being a naturally available polymer, has gained interest from researchers for replacing polyvinyl alcohol as a stabilizer. New research on sustainable, economical, biodegradable, renewable, and environmentally friendly starch grafted polyvinyl acetate emulsion that was synthesized by the graft polymerization of vinyl acetate monomer onto starch. However, starch grafted polyvinyl acetate emulsion-based adhesive’s properties, such as poor water resistance, weak adhesion, delayed drying rate and delayed setting speed, have resulted in limitations in its application as a wood adhesive. A detailed review of starch grafting on vinyl acetate and comonomers like acrylamides, and acrylic acid, and the addition of nano-fillers to enhance the water resistance and performance properties of sustainable adhesives has been explained.

Resistance and Seakeeping Investigation for Optimization of the Floating Hull of Wave Glider

Wave glider is the first unmanned autonomous marine robot to use only the ocean’s endless supply of wave energy for propulsion. Wave glider comprises fin system, tether and float which harvest all of its energy from waves and sun to produce forward thrust. As a consequence of the lack of design information and data for the wave glider, the main aim of the study is using computational fluid dynamics (CFD) to present a method to predict calm water resistance for the floating hull through calculations of 3 different hull forms using the same mesh generation under the same conditions. Calculations are carried out using 3 different mesh sizes for Froude number in the range of 0.10 to 0.40 and compared for accuracy of the solution parameters. Wigley parabolic hull, high speed round bilge form (NPL) and Series 60 have been comparatively investigated in order to estimate the hydrodynamics performance of the hull. The linear seakeeping analysis, coupled heave and pitch motions, roll motion, in irregular waves, with one parameter Bretschneider and JONSWAP spectra. Numerical computations have been performed for motion response predictions of the three hulls which cover wave angles from 0? to 180? at 45? intervals for six different forward speeds from 0 to 4.304 knots using Maxsurf Motion software. The close agreement between the numerical predictions shows the importance of CFD applications in estimating the hydrodynamics performance to design the floating hull and the numerical method is useful in glider design. The fine grid is fit to the calculation and shows the most appropriate results because convergent results are obtained as the mesh size decrease so the fine grid is the one which will be applied for the other hulls. Also it can be observed that the added resistance and the RAOs for NPL hull are less than the other hulls. Therefore from the comparisons, the NPL hull is the optimum hull compared to the other hulls from the resistance and seakeeping point of view.

Analysis of Shop cold water stability of asphalt concrete composite

He cold asphalt concrete is laid composite that combines the advantages of rigid cement concrete and asphalt concrete flexible pavement materials and new waterproof materials, and it is also known as semi-rigid concrete or semi-rigid waterproof concrete. Cold paved asphalt concrete composite retains the advantages of rigid and flexible waterproof material waterproof material which abandoned both of their inadequacies, is waterproof material with a wide range of space research and application prospects. This study immersion Marshall test and freeze-thaw split test two test methods for cold-laid asphalt concrete composite conducted a comprehensive analysis of the stability of the water; the highest draw AC1-6 AC-20 immersion Marshall stability and 20.59, respectively, by testing MPa and 19.96 Mpa, freeze-thaw splitting strength to reach the highest ratio of 91% and 93% respectively, the value specification can be met, and through the analysis of the test data to identify the content of the asphalt cement content and cold water laid asphalt compound affect the stability of the peak will occur, so that it can be combined with concrete interfacial adhesion studies to further the comprehensive and accurate assessment of water resistance of the material.

Research of the electrical anisotropic characteristics of water-conducting fractured zones in coal seams

Water flooding disasters are one of the five natural coal-mining disasters that threaten the lives of coal miners. The main causes of this flooding are water-conducting fractured zones within coal seams. However, when resistivity methods are used to detect water-conducting fractured zones in coal seams, incorrect conclusions can be drawn because of electrical anisotropy within the water-conducting fractured zones. We present, in this paper, a new geo-electrical model based on the geology of water-conducting fractured zones in coal seams. Factors that influence electrical anisotropy were analyzed, including formation water resistivity, porosity, fracture density, and fracture surface roughness, pressure, and dip angle. Numerical simulation was used to evaluate the proposed electrical method. The results demonstrate a closed relationship between the shape of apparent resistivity and the strike and dip of a fracture. Hence, the findings of this paper provide a practical resistivity method for coal-mining production.

Layer regrouping for water-flooded commingled reservoirs at a high water-cut stage

Layer regrouping is to divide all the layers into several sets of production series according to the physical properties and recovery percent of layers at high water-cut stage, which is an important technique to improve oil recovery for high water-cut multilayered reservoirs. Dif- ferent regroup scenarios may lead to different production performances. Based on unstable oil-water flow theory, a multilayer commingled reservoir simulator is established by modifying the production split method. Taking into account the differences of layer properties, including per- meability, oil viscosity, and remaining oil saturation, the pseudo flow resistance contrast is proposed to serve as a characteristic index of layer regrouping for high water-cut multilayered reservoirs. The production indices of multi- layered reservoirs with different pseudo flow resistances are predicted with the established model in which the data are taken from the Shengtuo Oilfield. Simulation results show that the pseudo flow resistance contrast should be less than 4 when the layer regrouping is implemented. The K-means clustering method, which is based on the objec- tive function, is used to automatically carry out the layer regrouping process according to pseudo flow resistances. The research result is applied to the IV-VI sand groups of the second member of the Shahejie Formation in the Shengtuo Oilfield, a favorable development performance is obtained, and the oil recovery is enhanced by 6.08 %.

Water abundance of mine floor limestone by simulation experiment

The water abundance of mine floor limestone needs to be solved urgently as the average depth of coal mining in China has increased gradually. A method is presented to discuss water abundance with the numerical and physical layered geoelectrical model being established in the half-space, full-space and full-space with tunnel, respectively. The parameters of water abundance are changed in this study, which includes water quantity, water content and volume of abnormity of water-containing abnormity. Results indicate that the different work fields have different macroscopic influences on the apparent resistivity,and the water abundance parameters of water-containing abnormity have quantitative relationship with the apparent resistivity mean in abnormal regions(three-dimensional space region). The quantitative relationships are shown as following: firstly, the amount of water injection has negative linear correlation with the apparent resistivity mean; secondly, when abnormity is unsaturated, there is a negative power function relationship between water content and apparent resistivity mean; thirdly, the volume of abnormity and apparent resistivity mean behave as a decreasing power function law.