Flow Dynamics during the Hydrocarbon Exploitation for Prevention and Management of Water Venues in Oil Field: A Study Case of Crystal Field in Badila/Chad

The southern part of the Lake Chad basin is under the gas and oil petroleum industry due to its hydrocarbon potential for about twenty years. This project stands out as the main challenges of the hydrocarbon production and the management of fluxes particularly the groundwater venues. A comprehensive study is thus conducted to develop a dynamic and analytic model for diagnosing the production performances with a particular view on the management of groundwater venues. The three main concerned reservoirs subdivided on subunits evidence their proper characteristics. The porous media, their densities, the internal flows and the water injection techniques such as water flooding were thus adopted. The oil viscosity variability within the reservoirs creates different levels of mobility between water and oil, highlighting the challenges of water management. The material balance model and the behavior of the well analysis were taken in consideration within the identified aquifer, emphasizing the importance of keeping the pressure through injection. The control of water productions, the management of the reservoir, the well strategical position and the specific completions lead to the model functioning. In addition, the CO log and the Pulsed Neutron indicate their limitations as a result of the water salinity and the porosity of the aquifer. The management of groundwater venues at Badila requires various approaches throughout the lifetime of the Crystal field such as the data acquisition and remediation actions and prevention, under a permanent monitoring of the dynamic fluxes in the reservoirs.

Hybrid low salinity water and surfactant process for enhancing heavy oil recovery

Combining low salinity water (LSW) with surfactants has an enormous potential for enhancing oil recovery processes. However, there is no consensus about the mechanisms involved, in addition to the fact that several studies have been conducted in model systems, while experiments with rocks and reservoir fluids are scarce. This study presents a core-flooding experiment of LSW injection, with and without surfactant, using the core and heavy oil samples obtained from a sandstone reservoir in southeastern Mexico. The effluents and the crude oil obtained at each stage were analyzed. The study was complemented by tomographic analysis. The results revealed that LSW injection and hybrid process with surfactants obtained an increase of 11.4 percentage points in recovery factor. Various phenomena were caused by LSW flooding, such as changes in wettability and pH, ion exchange, mineral dissolution, detachment of fines and modification of the hydrocarbon profile. In the surfactant flooding, the reduction of interfacial tension and alteration of wettability were the main mechanisms involved. The findings of this work also showed that the conditions believed to be necessary for enhanced oil recovery with LSW, such as the presence of kaolinite or high acid number oil, are not relevant.

Research progress and potential of new enhanced oil recovery methods in oilfield development

This paper reviews the basic research means for oilfield development and also the researches and tests of enhanced oil recovery(EOR)methods for mature oilfields and continental shale oil development,analyzes the problems of EOR methods,and proposes the relevant research prospects.The basic research means for oilfield development include in-situ acquisition of formation rock/fluid samples and non-destructive testing.The EOR methods for conventional and shale oil development are classified as improved water flooding(e.g.nano-water flooding),chemical flooding(e.g.low-concentration middle-phase micro-emulsion flooding),gas flooding(e.g.micro/nano bubble flooding),thermal recovery(e.g.air injection thermal-aided miscible flooding),and multi-cluster uniform fracturing/water-free fracturing,which are discussed in this paper for their mechanisms,approaches,and key technique researches and field tests.These methods have been studied with remarkable progress,and some achieved ideal results in field tests.Nonetheless,some problems still exist,such as inadequate research on mechanisms,imperfect matching technologies,and incomplete industrial chains.It is proposed to further strengthen the basic researches and expand the field tests,thereby driving the formation,promotion and application of new technologies.

Experimental study of the effects of a multistage pore-throat structure on the seepage characteristics of sandstones in the Beibuwan Basin:Insights into the flooding mode

To investigate the relationship between grain sizes, seepage capacity, and oil-displacement efficiency in the Liushagang Formation of the Beibuwan Basin, this study identifies the multistage pore-throat structure as a crucial factor through a comparison of oil displacement in microscopic pore-throat experiments. The two-phase flow evaluation method based on the Li-Horne model is utilized to effectively characterize and quantify the seepage characteristics of different reservoirs, closely relating them to the distribution of microscopic pores and throats. It is observed that conglomerate sandstones at different stages exhibit significant heterogeneity and noticeable differences in seepage capacity, highlighting the crucial role played by certain large pore throats in determining seepage capacity and oil displacement efficiency. Furthermore, it was found that the displacement effects of conglomeratic sandstones with strong heterogeneity were inferior to those of conventional homogeneous sandstone, as evidenced by multiple displacement experiments conducted on core samples with varying granularities and flooding systems. Subsequently, core-based experiments on associated gas flooding after water flooding were conducted to address the challenge of achieving satisfactory results in a single displacement mode for reservoirs with significant heterogeneity. The results indicate that the oil recovery rates for associated gas flooding after water flooding increased by 7.3%-16.4% compared with water flooding alone at a gas-oil ratio of approximately 7000 m^(3)/m^(3). Therefore, considering the advantages of gas flooding in terms of seepage capacity, oil exchange ratio, and the potential for two-phase production, gas flooding is recommended as an energy supplement mode for homogeneous reservoirs in the presence of sufficient gas source and appropriate tectonic angle. On the other hand, associated gas flooding after water flooding is suggested to achieve a more favorable development effect compared to a single mode of energy supplementation for strongly heterogeneous sandstone reservoirs.

Effects of physical parameter range on dimensionless variable sensitivity in water flooding reservoirs

The similarity criterion for water flooding reservoir flows is concerned with in the present paper. When finding out all the dimensionless variables governing this kind of flow, their physical meanings are subsequently elucidated. Then, a numerical approach of sensitivity analysis is adopted to quantify their corresponding dominance degree among the similarity parameters. In this way, we may finally identify major scaling law in different parameter range and demonstrate the respective effects of viscosity, permeability and injection rate.

Efficiency of enhanced oil recovery by injection of low-salinity water in barium-containing carbonate reservoirs

When low-salinity water containing sulfate ions is injected into carbonate reservoirs, rock dissolution and in situ precipitation occur, altering rock permeability and wettability. Particularly, when barium ions are present in formation water,they react chemically with SO;, and BaSO;is precipitated. These reactions can cause a serious impact on the efficiency of enhanced oil recovery（EOR）. Therefore, the main purpose of this study was to identify EOR efficiency induced by lowsalinity waterflooding（LSWF） when Ba;is present in carbonate reservoirs. From the experimental results, it was confirmed that the permeability calculated by the measured pressure difference was improved because of rock dissolution predominating over in situ precipitation for the case of low Ba;concentrations. In the analysis of wettability alteration through the measurements of relative permeabilities before and after LSWF, the higher Ba;concentration case consumed more SO;in precipitating the BaSO;, resulting in weaker wettability alteration due to the reduction of sulfate activity.These phenomena ultimately influenced EOR efficiency, i.e., the oil recovery was greater for the lower Ba;concentration.

Theoretical exploration of water injection gravity flooding oil in ultra-deep fault-controlled fractured-cavity carbonate reservoirs

Based on the analysis of geological characteristics of ultra-deep fault-controlled fracture-cavity carbonate reservoirs and division of reservoir units, two physical models were made, and physical simulations of oil displacement by water injection were carried out to find out water flooding mechanism in the fault-controlled fracture-cavity carbonate reservoir under complex flow state. On this basis, a mathematical model of fault-controlled carbonate reservoir with coexisting seepage and free flow has been established. Pilot water injection tests have been carried out to evaluate the effects of enhancing oil recovery by water injection. The results show that: fault-controlled fracture-cavity carbonate reservoir units can be divided into three types:the strong natural energy connected type, the weak natural energy connected type and the weak natural energy isolated type;the fault-fracture activity index of the fault-controlled fractured-cavity body can effectively characterize the connectivity of the reservoir and predict the effective direction of water injection;the mathematical model of fault-controlled carbonate reservoir with coexisting seepage and free flows can quantitatively describe the fluid flow law in the fracture-cavity body;the water injected into the fault-controlled fracture-cavity body is weakly affected by the capillary force of the lithologic body, and the oil-water movement is mainly dominated by gravity. The development modes of single well water injection, unit water injection,and single well high pressure water injection proposed based on the connection structure of fracture-cavity space and well storage space configuration are confirmed effective by pilot tests, with obvious water injection gravity flooding effect.

A production prediction method of single well in water flooding oilfield based on integrated temporal convolutional network model

Since the oil production of single well in water flooding reservoir varies greatly and is hard to predict, an oil production prediction method of single well based on temporal convolutional network(TCN) is proposed and verified. This method is started from data processing, the correspondence between water injectors and oil producers is determined according to the influence radius of the water injectors, the influence degree of a water injector on an oil producer in the month concerned is added as a model feature, and a Random Forest(RF) model is built to fill the dynamic data of water flooding. The single well history is divided into 4 stages according to its water cut, that is, low water cut, middle water cut, high water cut and extra-high water cut stages. In each stage, a TCN based prediction model is established, hyperparameters of the model are optimized by the Sparrow Search Algorithm(SSA). Finally, the models of the 4 stages are integrated into one whole-life model of the well for production prediction. The application of this method in Daqing Oilfield, NE China shows that:(1) Compared with conventional data processing methods, the data obtained by this processing method are more close to the actual production, and the data set obtained is more authentic and complete.(2) The TCN model has higher prediction accuracy than other 11 models such as Long Short Term Memory(LSTM).(3) Compared with the conventional full-life-cycle models, the model of integrated stages can significantly reduce the error of production prediction.

Displacement behavior and mechanism of long-term water flooding in sandstone oil reservoirs

Sandstone oil reservoirs with huge bottom water and high permeability are generally developed with high flow rate.After long-term water flooding(LTWF),the water flooding characteristics are quite different from that of original reservoir.In this paper,the effects of the PV number,viscosity,and displacement rate during LTWF are studied through experiments.The mechanism is analyzed based on analysis of changes in oil composition,rock mineral composition and wettability.The oil-water relative permeability curves,oil recovery and wettability were obtained with new experiments methods,which avoids the oil metering error by measuring oil and water separately.The research indicates that when the viscosity increases,the water phase permeability decreases,the residual oil saturation increases,and the water content rate increases earlier.A higher water flooding rate results in a higher ultimate recovery.A higher asphaltene content results in a higher viscosity and more oil-wet reservoir conditions.After LTWF,the wettability tends to water-wet,which is more favorable for heavy oil recovery.Moreover,LTWF reduces the clay content,which creates a more water-wet surface and a larger reservoir pore throat environment.This research provides insightful characteristics of offshore sandstone oil reservoirs,which can be used to enhance oil recovery.

Application of New Water Flooding Characteristic Curve in the High Water-Cut Stage of an Oilfield

The oil production predicted by means of the conventional water-drive characteristic curve is typically affected by large deviations with respect to the actual value when the so-called high water-cut stage is entered.In order to solve this problem,a new characteristic relationship between the relative permeability ratio and the average water saturation is proposed.By comparing the outcomes of different matching methods,it is verified that it can well reflect the variation characteristics of the relative permeability ratio curve.Combining the new formula with a reservoir engineering method,two new formulas are derived for the water flooding characteristic curve in the high water-cut stage.Their practicability is verified by using the production data of Mawangmiao and Xijiakou blocks.The results show that the error between the predicted cumulative oil production and production data of the two new water drive characteristic curves is less than the error between the B-type water drive characteristic curve and the other two water drive characteristic curves.It is concluded that the two new characteristic curves can be used to estimate more accurately the recoverable reserves,the final recovery and to estimate the effects of water flooding.

Effects of salinity and ionic composition of smart water on mineral scaling in carbonate reservoirs during water flooding

This work was conducted to study the risk of formation damage as the result of mineral scales deposition during smart waterflooding into carbonate core sample,as well as the influence of injected water salinity and ionic composition on mineral scaling and precipitation.The reservoir flowing conditions were simulated by a new laboratory core-flooding procedure,which took into count of the effect of in-situ contact time(CT)of injected water and formation water on scaling.After the optimum CT was determined,extent of permeability decline was studied by the change in the salinity and ionic composition of injection seawater.The scaled core sample was analyzed visually by scanning electron microscopy(SEM)to study the crystal morphology of the scale.Under the experimental conditions,extent of permeability decline caused by CaSO_(4) and CaSO_(3) composite scales ranged from 61% to 79.1% of the initial permeability.The salinity and the ionic composition of injected smart water,and CT of the mixing waters had significant effects on the co-precipitation of CaSO_(4) and CaSO_(3) scales.The SEM images reveal that the loss of permeability is mainly caused by the accumulation and growth perpendicular to the pore wall of scale crystals.

Stochastic and upscaled analytical modeling of fines migration in porous media induced by low-salinity water injection

Fines migration induced by injection of low-salinity water(LSW) into porous media can lead to severe pore plugging and consequent permeability reduction. The deepbed filtration(DBF) theory is used to model the aforementioned phenomenon, which allows us to predict the effluent concentration history and the distribution profile of entrapped particles. However, the previous models fail to consider the movement of the waterflood front. In this study, we derive a stochastic model for fines migration during LSW flooding, in which the Rankine-Hugoniot condition is used to calculate the concentration of detached particles behind and ahead of the moving water front. A downscaling procedure is developed to determine the evolution of pore-size distribution from the exact solution of a large-scale equation system. To validate the proposed model,the obtained exact solutions are used to treat the laboratory data of LSW flooding in artificial soil-packed columns. The tuning results show that the proposed model yields a considerably higher value of the coefficient of determination, compared with the previous models, indicating that the new model can successfully capture the effect of the moving water front on fines migration and precisely match the effluent history of the detached particles.

Inter-well interferences and their influencing factors during water flooding in fractured-vuggy carbonate reservoirs

Based on the characteristics of injection-production units in fractured-vuggy carbonate reservoirs,nine groups of experiments were designed and performed to analyze the interference characteristics and their influencing factors during water flooding.Based on percolation theory,an inversion model for simulating waterflooding interferences was proposed to study the influence laws of different factors on interference characteristics.The results show that well spacing,permeability ratio,cave size,and cave location all affect the interference characteristics of water flooding.When the cave is located in high permeability fractures,or in the small well spacing direction,or close to the producer in an injection-production unit,the effects of water flooding are much better.When the large cave is located in the high-permeability or small well spacing direction,the well in the direction with lower permeability or smaller well spacing will see water breakthrough earlier.When the cave is in the higher permeability direction and the reserves between the water injector and producer differ greatly,the conductivity differences in different injection-production directions are favorable for water flooding.When the injection-production well pattern is constructed or recombined,it’s better to make the reserves of caves in different injection-production directions proportional to permeability,and inversely proportional to the well spacing.The well close to the cave should be a producer,and the well far from the cave should be an injector.Different ratios of cave reserves to fracture reserves correspond to different optimal well spacings and optimal permeability ratios.Moreover,both optimal well spacing and optimal permeability ratio increase as the ratio of cave reserves to fracture reserves increases.

Mechanisms of remaining oil formation by water flooding and enhanced oil recovery by reversing water injection in fractured-vuggy reservoirs

To get a deeper understanding on the formation mechanisms and distribution laws of remaining oil during water flooding, and enhanced oil recovery(EOR) mechanisms by reversing water injection after water flooding, 3D visualization models of fractured-vuggy reservoir were constructed based on the elements and configuration of fractures and vugs, and typical fracture-vug structures by using advanced CT scanning and 3D printing technologies. Then, water flooding and reversing water injection experiments were conducted. The formation mechanisms of remaining oil during water flooding include inadequate injection-production well control, gravity difference between oil and water, interference between different flow channels, isolation by low connectivity channel, weak hydrodynamic force at the far end. Under the above effects, 7 kinds of remaining oil may come about, imperfect well-control oil, blind side oil, attic oil at the reservoir top, by-pass residual oil under gravity, by-pass residual oil in secondary channel, isolated oil in low connectivity channel, and remaining oil at far and weakly connected end. Some remaining oil can be recovered by reversing water injection after water flooding, but its EOR is related to the remaining oil type, fracture-cavity structure and reversing injection-production structure. Five of the above seven kinds of remaining oil can be produced by six EOR mechanisms of reversing water injection: gravity displacement, opening new flow channel, rising the outflow point, hydrodynamic force enhancement, vertically equilibrium displacement, and synergistic effect of hydrodynamic force and gravity.

Artificial neural network based production forecasting for a hydrocarbon reservoir under water injection

As the conventional prediction methods for production of waterflooding reservoirs have some drawbacks, a production forecasting model based on artificial neural network was proposed, the simulation process by this method was presented, and some examples were illustrated. A workflow that involves a physics-based extraction of features was proposed for fluid production forecasting to improve the prediction effect. The Bayesian regularization algorithm was selected as the training algorithm of the model. This algorithm, although taking longer time, can better generalize oil, gas and water production data sets. The model was evaluated by calculating mean square error and determination coefficient, drawing error distribution histogram and the cross-plot between simulation data and verification data etc. The model structure was trained, validated and tested with 90% of the historical data, and blindly evaluated using the remaining. The predictive model consumes minimal information and computational cost and is capable of predicting fluid production rate with a coefficient of determination of more than 0.9, which has the simulation results consistent with the practical data.

Floodwater utilization of the Three Gorges Project

Floods are both risks and resources. Floodwater utilization is an important part of flood management. Considering the rising shortage of water resources, serious water pollution, and undersupply of electric power, it’s imperative to strengthen flood management. In light of the hydrological characteristics of the Three Gorges Project (TGP) on the Yangtze River in P. R. China, we investigated the necessity and feasibility of TGP floodwater utilization, proprosed dynamic control of limited water level during flood season of the reservoir and basin-wide integrated floodwater management as strategies, and identified problems that might occur in practice.

Geochemical characteristics of reservoir after water and polymer flooding in Xingshugang oilfield of Daqing

Collecting 44 oil-sand specimens of Pu-I Member in two inspection wells before and after polymer flooding in the thirteenth district of Xingshugang oilfield,with experimental analysis,the author obtained the data about oil viscosity,flow,oil saturation and oil displacement efficiency.The result shows that viscous oil predominates in the main remaining oil in Xingshugang oilfield after water flooding with a certain amount of low viscosity oil,high viscosity oil and heavy oil;after polymer flooding,the viscous oil is main ingredient.Compared with water flooding,the low mobility and poor oil can be spread by polymer flooding,expanding the affected area and improving sweep efficiency and oil recovery.The geochemical affecting factors of water flooding and oil displacement efficiency refer to reservoir flow,permeability and the viscosity of residual oil.In the reservoir with permeability from low to high,the polymer flooding efficiency is better than water flooding.It provides the basis for improving the water and polymer flooding efficiency of the Xingshugang oilfield.

Automatic measurement of three-phase contact angles in pore throats based on digital images

With the help of digital image processing technology, an automatic measurement method for the three-phase contact angles in the pore throats of the microfluidic model was established using the microfluidic water flooding experiment videos as the data source. The results of the new method were verified through comparing with the manual measurement data.On this basis, the dynamic changes of the three-phase contact angles under flow conditions were clarified by the contact angles probability density curve and mean value change curve. The results show that, for water-wetting rocks, the mean value of the contact angles is acute angle during the early stage of the water flooding process, and it increases with the displacement time and becomes obtuse angle in the middle-late stage of displacement as the dominant force of oil phase gradually changes from viscous force to capillary force. The droplet flow in the remaining oil occurs in the central part of the pore throats, without three-phase contact angle. The contact angles for the porous flow and the columnar flow change slightly during the displacement and present as obtuse angles in view of mean values, which makes the remaining oil poorly movable and thus hard to be recovered. The mean value of the contact angle for the cluster flow tends to increase in the flooding process, which makes the remaining oil more difficult to be recovered. The contact angles for the membrane flow are mainly obtuse angles and reach the highest mean value in the late stage of displacement, which makes the remaining oil most difficult to be recovered. After displacement, the remaining oils under different flow regimes are just subjected to capillary force, with obtuse contact angles, and the wettability of the pore throat walls in the microfluidic model tends to be oil-wet under the action of crude oil.

Two-phase flow thermo-hydro-mechanical modeling for a water flooding field case

Simulation of subsurface energy system involves multi-physical processes such as thermal,hydraulical,and mechanical(THM)processes,and requires a so-called THM coupled modeling approach.THM coupled modeling is commonly performed in geothermal energy production.However,for hydrocarbon extraction,we need to consider multiphase flow additionally.In this paper,we describe a three-dimensional numerical model of non-isothermal two-phase flow in the deformable porous medium by integrating governing equations of two-phase mixture in the porous media flow in the reservoir.To account for inter-woven impacts in subsurface condi-tions,we introduced a temperature-dependent fluid viscosity and a fluid density along with a strain-dependent reservoir permeability.Subsequently,we performed numerical experiments of a ten-year water flooding pro-cess employing the open-source parallelized code,OpenGeoSys.We considered different well patterns with colder water injection in realistic scenarios.Our results demonstrate that our model can simulate complex interactions of temperature,pore pressure,subsurface stress and water saturation simultaneously to evaluate the recovery per-formance.High temperature can promote fluid flow while cold water injection under non-isothermal conditions causes the normal stress reduction by significant thermal stress.Under different well patterns the displacement efficiency will be changed by the relative location between injection and production wells.This finding has provided the important reference for fluid flow and induced stress evolution during hydrocarbon exploitation under the environment of large reservoir depth and high temperature.

Dam Safety in Jordan: Factors Affecting Dam Safety, Responsibilities and Required Actions

Dams in Jordan are exposed to a variety of natural and manmade threats like dams worldwide, but with some peculiar threats due to Jordan’s semi-arid climate, steep topography, tectonic activity, especially along the Jordan Rift Valley, position in the turbulent Middle East area, and weak socio-economic situation. In this study, the threats facing the main dams in Jordan are discussed and their sources are defined. The responsible agencies for reducing the threats and eliminating their sources are identified, as long as they are manmade. Natural threats are dealt with as superimposed and Jordan has to adapt to them by taking the necessary protective measures. The study concludes that all dams in Jordan are threatened by climate change and siltation and hence reduction in storage. The quality of stored water in dams, which are used for supplying drinking water such as Al-Wehdah, Wadi Al-Arab, Ziglab, Al-Wala and to a certain extent Al-Mujib is threatened by pollution due to urbanization, agricultural and industrial activities. All dams in Jordan are exposed to sabotage threats, which may negatively affect dams’ water quantities and quality. The stability of dams due to engineering failures is observed in the cases of Al-Kafrain, the left abutment of Al-Mujib, the spillway of Wheidi and eventually Al-Wala Dam. The latter was raised based on unique construction technology. The study recommends developing and implementing, as soon as possible, rigorous action plans to eliminate or, minimize the impacts of threats facing dams in Jordan.