Adaptive Bistable Stochastic Resonance Based Weak Signal Reception in Additive Laplacian Noise

Weak signal reception is a very important and challenging problem for communication systems especially in the presence of non-Gaussian noise,and in which case the performance of optimal linear correlated receiver degrades dramatically.Aiming at this,a novel uncorrelated reception scheme based on adaptive bistable stochastic resonance(ABSR)for a weak signal in additive Laplacian noise is investigated.By analyzing the key issue that the quantitative cooperative resonance matching relationship between the characteristics of the noisy signal and the nonlinear bistable system,an analytical expression of the bistable system parameters is derived.On this basis,by means of bistable system parameters self-adaptive adjustment,the counterintuitive stochastic resonance(SR)phenomenon can be easily generated at which the random noise is changed into a benefit to assist signal transmission.Finally,it is demonstrated that approximately 8dB bit error ratio(BER)performance improvement for the ABSR-based uncorrelated receiver when compared with the traditional uncorrelated receiver at low signal to noise ratio(SNR)conditions varying from-30dB to-5dB.

Weak signal detection method based on novel composite multistable stochastic resonance

The weak signal detection method based on stochastic resonance is usually used to extract and identify the weak characteristic signal submerged in strong noise by using the noise energy transfer mechanism.We propose a novel composite multistable stochastic-resonance(NCMSR)model combining the Gaussian potential model and an improved bistable model.Compared with the traditional multistable stochastic resonance method,all the parameters in the novel model have no symmetry,the output signal-to-noise ratio can be optimized and the output amplitude can be improved by adjusting the system parameters.The model retains the advantages of continuity and constraint of the Gaussian potential model and the advantages of the improved bistable model without output saturation,the NCMSR model has a higher utilization of noise.Taking the output signal-to-noise ratio as the index,weak periodic signal is detected based on the NCMSR model in Gaussian noise andαnoise environment respectively,and the detection effect is good.The application of NCMSR to the actual detection of bearing fault signals can realize the fault detection of bearing inner race and outer race.The outstanding advantages of this method in weak signal detection are verified,which provides a theoretical basis for industrial practical applications.

Novel Woods-Saxon stochastic resonance system for weak signal detection

We propose a joint exponential function and Woods–Saxon stochastic resonance(EWSSR)model.Because change of a single parameter in the classical stochastic resonance model may cause a great change in the shape of the potential function,it is difficult to obtain the optimal output signal-to-noise ratio by adjusting one parameter.In the novel system,the influence of different parameters on the shape of the potential function has its own emphasis,making it easier for us to adjust the shape of the potential function.The system can obtain different widths of the potential well or barrier height by adjusting one of these parameters,so that the system can match different types of input signals adaptively.By adjusting the system parameters,the potential function model can be transformed between the bistable model and the monostable model.The potential function of EWSSR has richer shapes and geometric characteristics.The effects of parameters,such as the height of the barrier and the width of the potential well,on SNR are studied,and a set of relatively optimal parameters are determined.Moreover,the EWSSR model is compared with other classical stochastic resonance models.Numerical experiments show that the proposed EWSSR model has higher SNR and better noise immunity than other classical stochastic resonance models.Simultaneously,the EWSSR model is applied to the detection of actual bearing fault signals,and the detection effect is also superior to other models.

Stochastic resonance in a time-delayed bistable system subject to multiplicative and additive noise

This paper investigates the stochastic resonance in a time-delayed bistable system subjected to multiplicative and additive white noise and asymmetric dichotomous noise. Under the adiabatic approximation condition, the expression of the signal-to-noise ratio （SNR） is obtained. It finds that the SNR is a non-monotonic function of the delayed times, of the amplitude of the driving square-wave signal, as well as of the asymmetry of the dichotomous noise. In addition, the SNR varies non-monotonously with the intensities of the multiplicative and additive noise as well as the system parameters. Moreover, the SNR depends non-monotonically on the correlate rate of the dichotomous noise.

Signal modulating noise effect in bistable stochastic resonance systems and its analog simulation

The effect of signal modulating noise in bistable stochastic resonance systems was studied theoretically and experimentally. A mathematical analysis was made on the bistable stochastic resonance model with small system parameters. An analogue circuit was designed to perform the effect. The effect of signal modulating noise was shown in the analog simulation experiment. The analog experiment was conducted for two sinusoidal signals with different frequencies. The results show that there are a sinusoidal component corresponding to the input sinusoidal signal and a noise component presented as a Wiener process corresponding to the input white noise in the system output. By properly selecting system parameters, the effect of signal modulating noise can be manifested in the system output.

Stochastic resonance in an asymmetric bistable system driven by coloured correlated multiplicative and additive noise

This paper investigates the stochastic resonance （SR） phenomenon in an asymmetric system with coupling between multiplicative and additive noise when the coupling between two noise terms is coloured. The approximate expression of signal-to-noise ratio has been obtained by applying the two-state theory and SR exhibits in the bistable system. Moreover, the potential asymmetry r and cross-correlation strength λ can weaken the SR phenomenon, while the cross-correlation time r can strengthen the SR phenomenon.

Implication of two-coupled tri-stable stochastic resonance in weak signal detection

Stochastic resonance （SR） has been proved to be an effective approach to extract weak signals overwhelmed in noise. However, the detection effect of current SR models is still unsatisfactory. Here, a coupled tri-stable stochastic resonance （CTSSR） model is proposed to further increase the output signal-to-noise ratio （SNR） and improve the detection effect of SR. The effects of parameters a, b, c, and r in the proposed resonance system on the SNR are studied, by which we determine a set of parameters that is relatively optimal to implement a comparison with other classical SR models. Numerical experiment results indicate that this proposed model performs better in weak signal detection applications than the classical ones with merits of higher output SNR and better anti-noise capability.

Adaptive stochastic resonance method for weak signal detection based on particle swarm optimization

In order to solve the parameter adjustment problems of adaptive stochastic resonance system in the areas of weak signal detection,this article presents a new method to enhance the detection efficiency and availability in the system of two-dimensional Duffing based on particle swarm optimization.First,the influence of different parameters on the detection performance is analyzed respectively.The correlation between parameter adjustment and stochastic resonance effect is also discussed and converted to the problem of multi-parameter optimization.Second,the experiments including typical system and sea clutter data are conducted to verify the effect of the proposed method.Results show that the proposed method is highly effective to detect weak signal from chaotic background,and enhance the output SNR greatly.

Asymmetric stochastic resonance under non-Gaussian colored noise and time-delayed feedback

Based on adiabatic approximation theory,in this paper we study the asymmetric stochastic resonance system with time-delayed feedback driven by non-Gaussian colored noise.The analytical expressions of the mean first-passage time(MFPT)and output signal-to-noise ratio(SNR)are derived by using a path integral approach,unified colored-noise approximation(UCNA),and small delay approximation.The effects of time-delayed feedback and non-Gaussian colored noise on the output SNR are analyzed.Moreover,three types of asymmetric potential function characteristics are thoroughly discussed.And they are well-depth asymmetry(DASR),well-width asymmetry(WASR),and synchronous action of welldepth and well-width asymmetry(DWASR),respectively.The conclusion of this paper is that the time-delayed feedback can suppress SR,however,the non-Gaussian noise deviation parameter has the opposite effect.Moreover,the correlation time plays a significant role in improving SNR,and the SNR of asymmetric stochastic resonance is higher than that of symmetric stochastic resonance.Our experiments demonstrate that the appropriate parameters can make the asymmetric stochastic resonance perform better to detect weak signals than the symmetric stochastic resonance,in which no matter whether these signals have low frequency or high frequency,accompanied by strong or weak noise.

Re-scaling and adaptive stochastic resonance as a tool for weak GNSS signal acquisition

Weak global navigation satellite system（GNSS） signal acquisition has been a limitation for high sensitivity GPS receivers. This paper modifies the traditional acquisition algorithms and proposes a new weak GNSS signal acquisition method using re-scaling and adaptive stochastic resonance（SR）. The adoption of classical SR is limited to low-frequency and periodic signals. Given that GNSS signal frequency is high and that the periodic feature of the GNSS signal is affected by the Doppler frequency shift, classical SR methods cannot be directly used to acquire GNSS signals. Therefore, the re-scaling technique is used in our study to expand its usage to high-frequency signals and adaptive control technique is used to gradually determine the Doppler shift effect in GNSS signal buried in strong noises. The effectiveness of our proposed method was verified by the simulations on GPS L1 signals. The simulation results indicate that the new algorithm based on SR can reach-181 d BW sensitivity with a very short data length of 1 ms.

Bistable Stochastic Resonance Enhanced 4-ary PAM Signal Detection under Low SNR

To boost the performance of 4-ary pulse amplitude modulated(PAM) at low signal-to-noise ratio(SNR), bistable stochastic resonance(BSR) system is introduced into digital communications system and get a reliable signal detection scheme. In this paper, we first analyse BSR system for different amplitudes of 4-ary PAM signals. The steadystate of the bistable system will be statistically distinct, and the feasibility of the proposed detection scheme is confirmed. On this basis, we present a detailed study on steady-state transitions of the BSR system, and an explicit expression of the bistable system parameters is derived. By setting the bistable system parameters, bistable system, 4-ary PAM signal, and noise reach the resonance state, and the BSR-based detection scheme is implemented. Moreover, we derive an analytical expression to calculate the symbol error rate(SER) of 4-ary PAM signals with the BSR-based detection under additive white Gaussian noise(AWGN). Finally, the simulation results validate that BSR-based detection scheme can improve the detection performance while efficiently reducing the symbol error rate.

Multi-scale bistable stochastic resonance array: A novel weak signal detection method and application in machine fault diagnosis

Weak signal detection based on stochastic resonance (SR) can hardly succeed when noise intensity exceeds the optimal value of SR. This paper explores a novel parallel bistable SR array mechanism by decomposed multi-scale noises from input signal. A smoother output with lower noise is obtained from the combination of colored noise SR effect and parallel bistable SR array. The influence of noise intensity and array size on the SR effect and output noise intensity is analyzed through numerical simulation. A signal detection method based on the new SR mechanism and normalized scale transform is proposed for the case of heavy background noise. Simulation is conducted to confirm the effectiveness of parameter tuning and amplitude tuning of normalized scale transform on the proposed SR model. The proposed method has three advantages: the input noise intensity of each unit is reduced by wavelet decomposition; the output noise level decreases due to array ensemble average; the SR effect of each unit is optimized by normalized scale transform for high frequency signal. Experiment on bearing inner and outer race fault diagnosis has verified the effectiveness and advantages of the proposed SR model in comparison with traditional SR method and kurtogram.

Stochastic resonance in an optical bistable system subjected to cross-correlated additive white noise and multiplicative colored noise

The stochastic resonance （SR） of an optical bistable system with cross-correlated additive white and multiplicative colored noises and periodic signal is studied using the unified colored noise approximation and the theory of signal-to-noise ratio （SNR）. Results show that cross-correlation intensity λ enforces the SR of the system. The position of the peak on the SNR-τ curves moves to the right direction along with the increase of λ （τ is the self-correlation time of the multiplicative colored noise）. We find the SR phenomenon in the SNR-D and SNR-Q curves （D and Q are the intensities of the additive and multiplicative noises, respectively）, but not in the SNR-λ curves.

Application of Stochastic Resonance Signal Recovery

Stochastic resonance（SR） enhances the nonlinear system behavior with the assistance of noise, including the sensitivity and selectivity of the response to the exterior stimulus. The energy-transfer mechanism makes the weak information revealed in the output spectrum, while the time-waveform is distorted. The distortion analysis was made both from the particle＇s dynan-fics and signal processing. The factors causing the deviation in the output are presented and the function of the recovery system is proposed. By the investigation of the particle＇s motion track in the bistable system and the suggested recovery system, the influences of noise and system parameters on the recovery course were discussed. Moreover, the pulse distortion appearing the recovery waveform caused by the particle＇s transitions at the bistable potential＇ inflexions was explained. Due to different characteristics, cascaded-bistable SR or mono-stable SR was introduced to process different types of signals. The final recovery signal is just the suggested recovery system＇s response to the SR output. Meanwhile, the recovery system is optional, as parameter-tuned or parameter-fixed. Since the method requires no average processing, it is applicable to a single sample with limited length. The numerical simulations reveal that the SR recovery method can recover the waveform containing weak information submerged ha noise effectively. The engineering application to the vibration analysis of metal cutting chose the combination of mono-stable SR and the parameter-fixed recovery system. Because the optimal SR state is not required strongly, the system parameters are tuned in a wider range than the traditional SR processing methods.

Preliminary Application of Scale Transformation Stochastic Resonance in Dual-Sequence Frequency Hopping System

Aiming at the detection failure of strong noise interference in the dual channel of the dual-sequence frequency hopping(DSFH),the scale transformation stochastic resonance(STSR)is applied for the first time,and the output signal to noise ratio(SNR)is raised effectively,at the same time,the symbol reception is completed for DSFH at low input SNR.Firstly,the radio frequency(RF)and intermediate frequency(IF)signals are analyzed based on the super-heterodyne reception of DSFH;secondly,the equations of probability density function(PDF),output power spectrum and SNR of the STSR output are derived for the IF signal;finally,the algorithm of the optimal matching STSR is proposed with the optimal matching parameters.The simulation results show that the algorithm can effectively solve the detection failure,as the global output SNR of DSFH is strongly improved that the output SNR can reach-17.72 d B when the input SNR is-20 d B after the processing of the optimal matching STSR.

油气测井微弱信号检测方法分析

文章分析研究了油气测井中微弱信号识别检测方法,首先回顾了微弱信号检测的传统方法,指出传统方法在处理高噪声环境下的微弱信号时的局限性;其次,详细介绍了非线性系统理论中的混沌理论和随机共振理论;最后,探讨了这些先进理论在油气测井微弱信号检测中的具体应用。该研究对提升油气资源勘探和开发的效率和准确性具有重要的实践意义,为油气测井领域提供了一种新的微弱信号检测策略。

基于混沌理论的电力系统微弱谐波检测方法研究

针对微弱谐波信号时频域分析检测方法在宽谱环境噪声较强场景中无法识别目标信号的缺陷,首先引入混沌系统的随机共振原理,在信号成分完全未知的情况下,利用随机噪声增强微弱目标信号进行频率盲检。进一步引入Duffing混沌系统,利用其对特定频率周期信号幅值的极高敏感性和噪声抵抗力,对检出的各谐波频率分量进行幅值精准检测。在经典随机共振模型的基础上,通过归一化改进了系统参数。结合Duffing混沌系统模型,设计了实时检测控制策略。通过粒子群寻优算法,以系统输入输出信号的互相关系数为适应度函数,寻找最优系统参数。对强随机噪声背景下的多整次谐波与间谐波混叠的谐波信号进行了仿真实验。结果表明,所提方法能在恶劣的噪声环境中,实现各谐波分量的无差频率检测与高精度幅值检测。

过阻尼非线性系统抑制大频率噪声机理及其弱信号检测研究

文章应用四阶Runge-Kutta算法对非线性Langevin方程进行分析,研究过阻尼非线性双稳态系统抑制噪声效应机理和大频率弱信号通过非线性双稳态系统的输出特性.数值计算结果表明,在选择适当系统参数的条件下,过阻尼非线性双稳态系统对伴随大频率弱信号的噪声具有强烈的抑制作用,使得输出信号的信噪比明显提高.将该系统用于强噪声背景下的弱信号检测,达到了识别大频率弱信号的目的,具有较高的应用价值.

高斯势分段双稳随机共振在不同噪声下的轴承故障诊断

为解决经典双稳随机共振(classical bistable stochastic resonance, CBSR)在强噪声下输出信噪比(signal-to-noise ratio, SNR)较低问题,将非饱和分段双稳随机共振(unsaturated piecewise bistable stochastic resonance, UPBSR)与高斯势(gaussian potential, GP)随机共振结合得到一种高斯势分段双稳随机共振(Gaussian potential piecewise bistable stochastic resonance, GPPBSR)。首先,将GPPBSR与CBSR、UPBSR的势函数分析对比;其次,以SNR和平均信噪比增益(mean signal-to-noise ratio increase, MSNRI)为衡量指标,分别在高斯白噪声和色噪声背景下通过遗传算法参数寻优得到SNR和MSNRI随系统参数的变化规律,其结果表明在两种噪声背景下,GPPBSR系统的SNR和MSNRI均优于UPBSR,抗噪性能更好;最后,为验证在不同场景下GPPBSR系统轴承故障诊断的实用性,将UPBSR和GPPBSR系统应用于6205-2RS JEM SKF和HRB 6205-2Z两种型号的轴承故障诊断中。仿真结果表明,GPPBSR系统在两种噪声背景下的故障信号诊断均是可行的,且比CBSR和UPBSR的性能更优越。

信标信号的随机共振稳态跃变检测方法

针对飞行数据记录器水下搜探中的微弱信标信号检测问题,本文提出了一种基于稳态跃变分布的信标信号随机共振检测方法。通过选取合理的混频器载波频率和非线性系统参数,实现了水下声信标信号这类高频窄脉宽信号的随机共振。引入势垒高度变换系数,通过研究非线性系统输出波形的稳态跃变分布特性,构建了检测统计量即稳态跃变适配次数。该方法可实现微弱信标信号的随机共振检测,调整势垒高度变换系数可使输出时域波形的稳态跃变分布产生变化,减少虚警。通过仿真及湖上试验表明:该方法检测性能优于频域能量检测方法。