基于SYSWELD的大厚板窄间隙双丝埋弧焊热过程数值模拟

基于60 mm厚Q345R钢,开展了窄间隙双丝埋弧焊焊接试验,得到了合理的工艺参数,焊缝成型平整均匀无任何缺陷.通过SYSWELD有限元软件对大厚板窄间隙双丝埋弧焊焊接热过程进行数值模拟分析,模拟的熔池宽与高和实际相比,误差率均控制在5%以内,并利用热电偶装置测得热影响区热循环曲线与模拟的热循环曲线变化趋势基本一致,具有升温快,降温慢的特点,验证了该模型的有效性.为后续利用该模型,进一步探究不同参数或边界条件对于大厚板窄间隙双丝埋弧焊焊接热过程与应力-应变规律提供理论指导.

Tri-Arc双丝焊“Γ”形电弧及其促进方法

Tri-Arc双丝三电弧焊通过中间第3弧的M弧重新分配焊接热输入,实现高熔覆率低热输入焊接.M弧与主电弧耦合,在整个动态周期表现为“Γ”形和“μ”形及其镜像形态.该文研究“Γ”形电弧的形成机理和热输入调控机制,结果表明,“Γ”形态由“μ”形态转变而来,熔滴振荡引起焊丝末端间距的变化,从而促进耦合电弧“Γ”形态的形成,此时M弧不作用于母材,比“μ”形电弧焊接热输入更低.为提高Tri-Arc双丝焊接低热输入效果,在维持导电嘴末端到工件距离不变的前提下,提高焊枪枪体抬升距离从而改变焊丝末端间距.当导电嘴长度由30 mm增加至35 mm时,随着焊枪抬升,“Γ”形电弧作用时间逐渐增加,能更好地促进电弧热分配,降低Tri-Arc双丝焊接热输入,从而降低熔池最高温度,获得更小宽高比和更小熔深的焊缝.

Study on gas metal arc welding of two types of TMCP steels

Gas metal arc welding experiments were conducted on two types of steels with 0.41% carbon equivalent(Ceq) and 0.31% Cequsing WER70T wire and 20% CO_(2)and 80% Ar as shielding gas.The two types of steels show satisfactory weldability.The transition temperatures of 50% upper shelf energy(Tk0.5) for Charpy-V impact test of both the welded joints are below-40 ℃.However, the toughness of the fusion line zone and heat-affected zone(HAZ) of the two steel joints exhibits differences, with the toughness of 0.41% Ceqsteel being better than that of 0.31% Ceqsteel.The Tk0.5of the fusion line zone and the HAZ of 0.41% Ceqsteel is below-60℃,whereas that of 0.31% Ceqsteel is above-40℃.The welded joint of 0.41% Ceqsteel has low hardness fluctuation, while that of 0.31% Ceqsteel exhibits a narrow, softened zone, which has no obvious influence on the tested tensile strength.The coarse grain heat-affected zone(CGHAZ)microstructure of 0.41% Ceqsteel is bainite, while that of 0.31% Ceqsteel is bainite with ferrite and minor pearlite.

Two-temperature modeling of lamellar cathode arc

A three-dimensional, two-temperature(2T) model of a lamellar cathode arc is constructed,drawing upon the conservation equations for mass, momentum, electron energy, and heavy particle energy, in addition to Maxwell's equations. The model aims to elucidate how the physical properties of electrons and heavy particles affect heat transfer and fluid flow in a lamellar cathode arc. This is achieved by solving and comparing the fields of electron temperature,heavy particle temperature, fluid flow, current density, and Lorentz force distribution under varying welding currents. The results show that the guiding effect of the lamellar cathode on current density, the inertial drag effect of moving arc, and the attraction effect of Lorentz force at the lamellar cathode tip primarily govern the distribution of the arc's physical fields. The guiding effect localizes the current density to the front end of the lamellar cathode, particularly where the discharge gap is minimal. Both the inertial drag effect and the attraction effect of Lorentz force direct arc flow toward its periphery. Under the influence of the aforementioned factors, the physical fields of the lamellar cathode arc undergo expansion and shift counter to the arc's direction of motion. A reduction in welding current substantially weakens the guiding effect,causing the arc's physical fields to deviate further in the direction opposite to the arc motion. In comparison with a cylindrical cathode arc, the physical fields of the lamellar cathode arc are markedly expanded, leading to a reduction in current density, electron temperature, heavy particle temperature, cathode jet flow velocity, and Lorentz force.

Microstructure and mechanical properties of AZ31B magnesium alloy gas metal arc weld

Wrought magnesium alloy sheets were butt welded with gas metal arc welding process. Pores in the weld were investigated under different welding parameters, the causes of pore formation were systematically disposed, and the effects of porosity on the microstructure and mechanical properties of the joint were analyzed. The microstructure examination shows that the pores mainly appear close to the top or bottom part of the weld, and could connect to each other and lead to the formation of cracks in the welds. However, the pores can be controlled with proper welding parameters. The tensile testing results reveal that the average joint strength is close to or higher than that of the base metal. The microhardness in the weld can be even higher than that in the base metal due to the second ohase strengthening of β-Mg17（A1, Zn）12 formed in the weld.

Effect of arc-ultrasound on microstructures and mechanical properties of plasma arc welded joints of SiC_p/Al MMCs

The effect of arc-ultrasound on microstructures and mechanical properties of SiCp/6061A1 MMCs joints produced by arc-ultrasound plasma arc ＂in-situ＂ alloy-welding with different excitation frequencies was investigated, in which argon-nitrogen mixture was used as plasma gas, Ti wire as filler and the arc-ultrasound was produced by modulating the plasma arc with high frequency. The results show that arc-ultrasound could refine the new reinforced composites such as TiC, TiN significantly, and improve their distribution greatly. And new phase A13Ti becomes finer and less. The test results of mechanical properties indicate that the maximum tensile strength of welded joints is gained when the excitation frequency is 50 kHz, and the maximum is 225 MPa, raising by about 7% comoared with conventional nlasma arc welding （PAW） （20q MPa）.

Welding of Ti-6Al-4V alloy using dynamically controlled plasma arc welding process

A novel dynamically controlled plasma arc welding process was introduced,which is able tominimize heat input into the workpiece materials while maintaining desired full penetration,and it was used to weld Ti-6Al-4V alloy sheets.The microstructures,facture surfaces and microhardness of the welded joints were characterized by using optical microscope,scanning electron microscope （SEM） and Vickers microhardness tester.Comparing with welds such as gas tungsten arc and conventional plasma arc processes,the experimental results revealed the improvements when using the present process including：1） reducing prior-beta （β） grain size and prohibiting formation of hard martensite phases in the fusion zone due to the decreased heat input;and 2） better toughness and higher hardness.

Sensitivity model for prediction of bead geometry in underwater wet flux cored arc welding

To investigate influence of welding parameters on weld bead geometry in underwater wet flux cored arc welding （FCAW）, orthogonal experiments of underwater wet FCAW were conducted in the hyperbaric chamber at water depth from 0.2 m to 60 m and mathematical models were developed by multiple curvilinear regression method from the experimental data. Sensitivity analysis was then performed to predict the bead geometry and evaluate the influence of welding parameters. The results reveal that water depth has a greater influence on bead geometry than other welding parameters when welding at a water depth less than 10 m. At a water depth deeper than 10 m, a change in travel speed affects the bead geometry more strongly than other welding parameters.

Microstructures and mechanical properties of metal inert-gas arc welded Mg-steel dissimilar joints

The joining of Mg alloy to steel was realized by metal inert-gas arc welding, and the weld thermal cycle characteristics and Mg-steel joints were investigated. The results show that the temperature distribution in the joints is uneven. Mg alloy welds present a fine equiaxed grain structure. There exists a transition layer consisting mainly of AlFe, AlFe3 and Mg（Fe, Al）2O4 phases at Mg/steel interface, and it is the weakest link in Mg？steel joints. The welding heat input and weld Al content have the significant effect on the joint strength. The joint strength increases with increasing the heat input from 1680 J/cm to 2093 J/cm, due to promoting Mg/steel interface reaction. When weld Al content is increased to 6.20%, the joint strength reaches 192 MPa, 80% of Mg alloy base metal strength. It is favorable to select the suitable welding heat input and weld Al content for improving joint strength.

Effects of welding wire composition and welding process on the weld metal toughness of submerged arc welded pipeline steel

The effects of alloying elements in welding wires and submerged arc welding process on the microstructures and low-temperature impact toughness of weld metals have been investigated. The results indicate that the optimal contents of alloying elements in welding wires can improve the low-temperature impact toughness of weld metals because the proeutectoid ferrite and bainite formations can be suppressed, and the fraction of acicular ferrite increases. However, the contents of alloying elements need to vary along with the welding heat input. With the increase in welding heat input, the contents of alloying elements in welding wires need to be increased accordingly. The microstructures mainly consisting of acicular ferrite can be obtained in weld metals after four-wire submerged arc welding using the wires with a low carbon content and appropriate contents of Mn, Mo, Ti-B, Cu, Ni, and RE, resulting in the high low-temperature impact toughness of weld metals.

COMPUTERIZED SIMULATION AND EXPERIMENTAL RESEARCH ON SOFT-SWITCHING ARC WELDING INVERTER POWER SOURCE

Based on the existing component models in the Pspice software package, a combined model for Insulat- ed the Bipolar Transistor (IGBT) is established, in which a non - linear is introduced to represent the parasitic capacitance. Using this model, computerized simulation is conducted for the FB - ZVZCS - PWM soft - ewitching converter,the switching and energy-transferring characteristics of the components are analyzed.The simulation results are testified by experiments.It is proved that by abopting appropriate models,computerized simulation becomes an effective tool for investigation of arc welding inverter power source.

The arc characteristic of ultrasonic assisted TIG welding

Many applications of ultrasonic-assisted methods were used during metal solidification, but they could not be introduced into weld pool. In this paper, a way of ultrasonic assisted TIG welding is introduced. By directly imposed ultrasonic vibration on welding arc, the vibration interacts with arc plasma and passes to the weld pool. Measurement results show that arc pressure is significantly increased with the ultrasonic vibration and the arc pressure distribution models are changed. Bead-on-plate welding tests on SUS304 confirm that this technology can influence the style of metal melting and increase weld penetration depth.

Electromagnetic Characteristic of Twin-wire Indirect Arc Welding

Traditional welding methods are limited in low heat input to workpiece and high welding wire melting rate. Twin-wire indirect arc（TWIA） welding is a new welding method characterized by high melting rate and low heat input. This method uses two wires one connected to the negative electrode and another to the positive electrode of a direct-current（DC） power source. The workpiece is an independent, non-connected unit. A three dimensional finite element model of TWIA is devised. Electric and magnetic fields are calculated and their influence upon TWIA behavior and the welding process is discussed. The results show that with a 100 A welding current, the maximum temperature reached is 17 758 K, arc voltage is 14.646 V while maximum current density was 61 A/mm2 with a maximum Lorene force of 84.5 ~tN. The above mentioned arc parameters near the cathode and anode regions are far higher than those in the arc column region. The Lorene force is the key reason for plasma velocity direction deviated and charged particles flowed in the channel formed by the cathode, anode and upper part of arc column regions. This led to most of the energy being supplied to the polar and upper part of arc column regions. The interaction between electric and magnetic fields is a major determinant in shaping TWIA as well as heat input on the workpiece. This is a first study of electromagnetic characteristics and their influences in the TWIA welding process, and it is significant in both a theoretical and practical sense.

MECHANICAL PROPERTIES OF LONGITUDINAL SUBMERGED ARC WELDED STEEL PIPES USED FOR GAS PIPELINE OF OFFSHORE OIL

Since the development of offshore oil and gas, increased submarine oil and gas pipelines were installed. All the early steel pipes of submarine pipelines depended on importing because of the strict requirements of comprehensive properties, such as, anti-corrosion, resistance to pressure and so on. To research and develop domes- tic steel pipes used for the submarine pipeline, the Longitudinal-seam Submerged Arc Welded （LSAW） pipes were made of steel plates cut from leveled hot rolled coils by both the JCOE and UOE （the forming process in which the plate like the letter “J”, “C”, “0” or “U” shape, then expansion） forming processes. Furthermore, the mechanical properties of the pipe base metal and weld metal were tested, and the results were in accordance with the corresponding pipe specification API SPEC 5L or DNV- OS-FI01, which showed that domestic LSAW pipes could be used for submarine oil and gas pipelines.

FRACTAL RESEARCH ON CRACKS PROPAGATION OF GAS PIPELINE X52 STEEL WELDING LINE UNDER HYDROGEN ENVIRONMENT

Based on the theory of hydrogen enhanced localized plasticity of the hydrogen induced cracking and the consideration of the effect of the residual stress produced by eliminated stress heat-treatment, a fractal model of hydrogen induced cracking was presented, and the relationships among the effective surface energy (H), fractal dimension D and stress intensity factor of hydrogen induced cracking, KIH, for welding pipeline under hydrogen environment was set up, from which the relationship of D and KISCC was obtained. The model has been verified experimentally to be correct.

Optimizing the Pulsed Current Gas Tungsten Arc Welding Parameters

The selection of process parameter in the gas tungsten arc （GTA） welding of titanium alloy was presented for obtaining optimum grain size and hardness. Titanium alloy （Ti-6Al-4V） is one of the most important non-ferrous metals which offers great potential application in aerospace, biomedical and chemical industries, because of its low density （4.5 g/cm^3）, excellent corrosion resistance, high strength, attractive fracture behaviour and high melting point （1678℃）. The preferred welding process for titanium alloy is frequent GTA welding due to its comparatively easier applicability and better economy. In the case of single pass （GTA） welding of thinner section of this alloy, the pulsed current has been found beneficial due to its advantages over the conventional continuous current process. Many considerations come into the picture and one needs to carefully balance various pulse current parameters to reach an optimum combination. Four factors, five level, central composite, rotatable design matrix were used to optimize the required number of experimental conditions. Mathematical models were developed to predict the fusion zone grain size using analysis of variance （ANOVA） and regression analysis. The developed models were optimized using the traditional Hooke and Jeeve＇s algorithm. Experimental results were provided to illustrate the proposed approach.

Arc characteristics of GMA welding in high-pressure air condition

Gas metal arc （ GMA ） welding process can be fluently executed under the range of 0. 1 - 0. 7 MPa air pressure shielded by C02 and ArS0% ＋ CO220% gases, which were tested by the igniting and exploding experiments using a hyperbaric chamber to simulate the underwater conditions. The arc voltage characteristics of the GMA welding were tested in hyperbaric conditions to discover the law of the welding arc affected by environmental pressure, welding current, stick-out, gas type and gas-flow. The experimental results and related discussion are also given in this paper. Finally, a mathematical model was calculated under high-pressure air condition based on the experimental data with the least square approximation method.

In situ synthesis and hardness of TiC/Ti_5Si_3 composites on Ti-5Al-2.5Sn substrates by gas tungsten arc welding

TiC/TisSi3 composites were fabricated on Ti-5A1-2.5Sn substrates by gas tungsten arc welding （GTAW）. Identification of the phases was performed using X-ray diffraction （XRD）. The microstructures were analyzed using scanning electron microscopy （SEM） combined with energy-dispersive X-ray spectrometry （EDS） and optical microscopy （OM）. The Vickers hardness was measured with a micro-hardness tester. The TiC/TisSi3 composites were obtained in a double-layer track, and the Vickers hardness of the track increased by two to three times compared with the Ti-5A1-2.5Sn substrate.

Arc characteristics of submerged arc welding with stainless steel wire

The arc characteristics of submerged arc welding （SAW） with stainless steel wire were studied by using Analysator Hannover （AH）. The tests were carded out under the same preset arc voltage combined with different welding currents. By comparing the probability density distribution （PDD） curves of arc voltage and welding current, the changes were analyzed, the metal transfer mode in SAW was deduced, and the characteristics of a stable arc were summarized. The analysis results show that, with an increase of welding parameters, the short-circuiting peak in the PDD curves of arc voltage decreases gradually until it disappears, and the dominant metal transfer mode changes from flux-wall guided transfer to projected transfer and then to streaming transfer. Moreover, when the PDD curves of arc voltage are both unimodal and generally symmetrical, the greater the peak probability and the smaller the peak span, the more stable the arc becomes.

Cold Cracking of Flux Cored Arc Welded Armour Grade High Strength Steel Weldments

In this investigation, an attempt has been made to study the influence of welding consumables on the factors that influence cold cracking of armour grade quenched and tempered （Q＆.T） steel welds. Flux cored arc welding （FCAW） process were used making welds using austenitic stainless steel （ASS） and low hydrogen ferritic steel （LHF） consumables. The diffusible hydrogen levels in the weld metal of the ASS and LHF consumables were determined by mercury method. Residual stresses were evaluated using X-ray stress analyzer and implant test was carried out to study the cold cracking of the welds. Results indicate that ASS welds offer a greater resistance to cold cracking of armour grade Q＆T steel welds.