Study on anisotropy of microstructure and mechanical properties of AZ31 magnesium alloy fabricated by wire arc additive manufacturing

Based on wire arc additive manufacturing(WAAM)technology,AZ31 magnesium alloy in bulk was successfully fabricated,and its microstructure as well as mechanical properties in different planes were observed and analyzed.The AZ31 magnesium alloy has a similar microstructure in the building direction(Z)and travel direction(X),both of which are equiaxed grains.There are heat-affected zones(HAZs)with coarse grains below the fusion line.The second phase is primarily composed of the Mg17Al12 phase,which is evenly distributed in different directions.In addition,the residual stress varies in different directions.There is no significant difference in the hardness of the AZ31 alloy along the Z and X directions,with the average hardness being 68.4 HV and 67.9 HV,respectively.Even though the specimens’ultimate tensile strength along the travel direction is higher in comparison to that along the building direction,their differences in elongation and yield strength are smaller,indicating that the anisotropy of the mechanical properties of the material is small.

Wire arc additive manufacturing of a heat-resistant Al-Cu-Ag-Sc alloy:microstructures and high-temperature mechanical properties

With a high energy efficiency,low geometric limitation,and low cracking susceptivity to cracks,wire arc additive manufacturing(WAAM)has become an ideal substitute for casting in the manufacturing of load-bearing high strength aluminum components in aerospace industry.Recently,in scientific researches,the room temperature mechanical performance of additive manufactured high strength aluminum alloys has been continuously broken through,and proves these alloys can achieve comparable or even higher properties than the forged counterpart.Since the aluminum components for aerospace usage experience high-low temperature cycling due to the absence of atmosphere protection,the high temperature performances of additive manufactured high strength aluminum alloys are also important.However,few research focuses on that.A special 2319Ag Sc with 0.4 wt.%Ag and 0.2 wt.%Sc addition designed for high temperature application is deposited successfully via cold metal transfer(CMT)based on WAAM.The microstructures and high temperature tensile properties are investigated.The results show that the as-deposited 2319Ag Sc alloy presents an alternate distribution of columnar grains and equiaxed grains with no significant textures.Main second phases are Al_(2)Cu and Al3Sc,while co-growth of Al_(2)Cu and bulk Al_(3)Sc is found on the grain boundary.During manufacturing,nanoscale Al_(2)Cu can precipitate out from the matrix.Ag and Mg form nano-scaleΩphase on the Al_(2)Cu precipitates.At 260℃,average yield strengths in the horizontal direction and vertical direction are 87 MPa±2 MPa,87 MPa±4 MPa,while average ultimate tensile strengths are 140 MPa±7 MPa,141 MPa±11 MPa,and average elongations are 11.0%±2.5%,13.5%±3.0%.Anisotropy in different directions is weak.

Effect of heat treatment on the microstructure and mechanical properties of AZ80M magnesium alloy fabricated by wire arc additive manufacturing

To maximize the benefits of wire arc additive manufacturing(WAAM)processes,the effect of post-deposition heat treatment on the microstructure and mechanical properties of WAAM AZ80M magnesium(Mg)alloy was investigated.Three different heat treatment procedures(T4,T5 and T6)were performed.According to the results,after T4 heat treatment,the microsegregation of alloying elements was improved with the eutectic structure dissolved.Samples after T5 heat treatment inherited the net-like distribution of secondary phases similar to the as-deposited sample,where the eutectic structure covering the interdendritic regions and theβ-phase precipitated around the eutectic structure.After T6 heat treatment,the tinyβ-phases re-precipitated from the matrix and distributed in inner and outer of the grains.The hardness distribution of the samples went through T4 and T6 heat treatment was more uniform in comparison to that of T5 heat treated samples.The tensile test showed that the T6 heat treatment improved the strength and ductility,and the anisotropy between horizontal and vertical can be eliminated.Moreover,T4 treated samples exhibited highest ductility.

Effect of interlayer cooling time on the temperature field of 5356-TIG wire arc additive manufacturing

In the paper, the finite element model(FEM) of wire arc additive manufacturing(WAAM) by TIG method was established by the ABAQUS soft, and the phase transformation latent heat was considered in the model. The evolution rules of temperature field at the interlayer with the cooling time of 10 s, 30 s and 50 s were obtained by the model. The WAAM experiment were performed by 5356 aluminum alloy welding wire with φ1.2 mm, and the simulated temperature field were varified by the thermocouple. The result shows that the highest temperature at the molten pool center increases with the increased interlayers at the same interlayer cooling time;the highest temperature drops gradually and the decline is smaller with the increased interlayer cooling time at the same layer. No remelting occurs at the top layer, and at least two remelting times occur in the other layers, resulting in complex temperature field evolution.

Influence of Ship-based Vibration on Characteristics of Arc and Droplet and Morphology in Wire Arc Additive Manufacturing

To explore the feasibility of using wire arc additive manufacturing(WAAM)for forming and repairing marine components during ship navigation,this study conducted deposition experiments of ER50-6 steel and investigated the interference of ship-based vibrations on the WAAM equipment and influence of the characteristics of the arc droplets and sample morphology.The results revealed that the WAAM equipment vibrated with the external vibrations from the surrounding environment,and the welding gun and base plate produced dissimilar vibrations,which yielded unstable arc shapes resembling a bell,trumpet,fan,broom,and other irregular shapes.The mode of the droplet transfer ranged from the stable spray transfer mode to extensive amounts of large droplet transfer and short-circuit transfer.Although the morphology of the obtained sample deteriorated,the fully dense and defect-free interior demonstrated the applicability of ship-based WAAM.

Deformation Characteristics and Mechanical Properties of Ti/Al Bimetallic Composite Materials Fabricated by Wire Plus Arc Additive Manufacturing

We focused on Ti/Al composite materials fabricated by wire and arc addictive manufacturing,and the microstructure and interface characteristics of them before and after hot compression deformation were compared.After compression deformation,allαstructures of titanium were compacted with the emergence of Widmanstatten structures.Coarsened coloniesαof titanium were elongated and waved along the original growth direction,resulting in anisotropy of grains.Pores and Ti/Al intermetallic compounds of aluminum are significantly decreased after hot compression.Meanwhile,a good bonding interface between titanium and aluminum is obtained after hot compression,and the element diffusion is more intense.In addition,the mechanical properties and fracture behaviors of Ti/Al composite material with different clad ratio that is defined as the ratio of the thickness of titanium to that of the Ti/Al composite material are investigated by uniaxial tensile test.The experimental results show that the ultimate tensile strength of Ti/Al composite material is between that of single deposited titanium and aluminum,while the elongation of Ti/Al composite material with low clad ratio is lower than that of single aluminum due to the metallurgical reaction.As the clad ratio increases,the two component layers are harder to separate during deformation,which is resulted from the decrease of the inward contraction stress of three-dimensional stress caused by necking of aluminum.This work may promote the engineering application of Ti/Al bimetallic structures.

Enhancing fatigue performance of AZ31 magnesium alloy components fabricated by cold metal transfer-based wire arc directed energy deposition through LPB

Cold Metal Transfer-Based Wire Arc Directed Energy Deposition(CMT-WA-DED)presents a promising avenue for the rapid fabrication of components crucial to automotive,shipbuilding,and aerospace industries.However,the susceptibility to fatigue of CMT-WA-DED-produced AZ31 Mg alloy components has impeded their widespread adoption for critical load-bearing applications.In this study,a comprehensive investigation into the fatigue behaviour of WA-DED-fabricated AZ31 Mg alloy has been carried out and compared to commercially available wrought AZ31 alloy.Our findings indicate that the as-deposited parts exhibit a lower fatigue life than wrought Mg alloy,primarily due to poor surface finish,tensile residual stress,porosity,and coarse grain microstructure inherent in the WA-DED process.Low Plasticity Burnishing(LPB)treatment is applied to mitigate these issues,which induce significant plastic deformation on the surface.This treatment resulted in a remarkable improvement of fatigue life by 42%,accompanied by a reduction in surface roughness,grain refinement and enhancement of compressive residual stress levels.Furthermore,during cyclic deformation,WA-DED specimens exhibited higher plasticity and dislocation density compared to both wrought and WA-DED+LPB specimens.A higher fraction of Low Angle Grain Boundaries(LAGBs)in WA-DED specimens contributed to multiple crack initiation sites and convoluted crack paths,ultimately leading to premature failure.In contrast,wrought and WA-DED+LPB specimens displayed a higher percentage of High Angle Grain Boundaries(HAGBs),which hindered dislocation movement and resulted in fewer crack initiation sites and less complex crack paths,thereby extending fatigue life.These findings underscore the effectiveness of LPB as a post-processing technique to enhance the fatigue performance of WA-DED-fabricated AZ31 Mg alloy components.Our study highlights the importance of LPB surface treatment on AZ31 Mg components produced by CMT-WA-DED to remove surface defects,enabling their widespread use in load-bearing applications.

Enhanced strength-ductility synergy in a wire and arc additively manufactured Mg alloy via tuning interlayer dwell time

Strength-ductility trade-off is a common issue in Mg alloys. This work proposed that a synergistic enhancement of strength and ductility could be achieved through tuning interlayer dwell time(IDT) in the wire and arc additive manufacturing(WAAM) process of Mg alloy.The thermal couples were used to monitor the thermal history during the WAAM process. Additionally, the effect of different IDTs on the microstructure characteristics and resultant mechanical properties of WAAM-processed Mg alloy thin-wall were investigated. The results showed that the stable temperature of the thin-wall component could reach 290 ℃ at IDT=0s, indicating that the thermal accumulation effect was remarkable. Consequently, unimodal coarse grains with an average size of 39.6 μm were generated, and the resultant room-temperature tensile property was poor. With the IDT extended to 60s, the thermal input and thermal dissipation reached a balance, and the stable temperature was only 170 ℃, closing to the initial temperature of the substrate. A refined grain structure with bimodal size distribution was obtained. The remelting zone had fine grains with the size of 15.2 μm, while the arc zone owned coarse grains with the size of 24.5 μm.The alternatively distributed coarse and fine grains lead to the elimination of strength-ductility trade-off. The ultimate tensile strength and elongation of the samples at IDT=60s are increased by 20.6 and 75.0% of those samples at IDT=0s, respectively. The findings will facilitate the development of additive manufacturing processes for advanced Mg alloys.

Wire and arc additive manufacturing of 4043 Al alloy using a cold metal transfer method

Cold metal transfer plus pulse(C+P)arc was applied in the additive manufacturing of 4043 Al alloy parts.Parameters in the manufacturing of the parts were investigated.The properties and microstructure of the parts were also characterized.Experimental results showed that welding at a speed of 8 mm/s and a wire feeding speed of 4.0 m/min was suitable to manufacture thin-walled parts,and the reciprocating scanning method could be adopted to manufacture thick-walled parts.The thin-walled parts of the C+P mode had fewer pores than those of the cold metal transfer(CMT)mode.The thin-and thick-walled parts of the C+P mode showed maximum tensile strengths of 172 and 178 MPa,respectively.Hardness decreased at the interface and in the coarse dendrite and increased in the refined grain area.

Enhanced interface strength in steel-nickel bimetallic component fabricated using wire arc additive manufacturing with interweaving deposition strategy

Realizing improved strength in composite metallic materials remains a challenge using conventional welding and joining systems due to the generation and development of brittle intermetallic compounds caused by complex thermal profiles during solidification.Here,wire arc additive manufacturing(WAAM)process was used to fabricate a steel-nickel structural component,whose average tensile strength of 634 MPa significantly exceeded that of feedstock materials(steel,537 MPa and nickel,455 MPa),which has not been reported previously.The as-fabricated sample exhibited hierarchically structural heterogeneity due to the interweaving deposition strategy.The improved mechanical response during tensile testing was due to the inter-locking microstructure forming a strong bond at the interface and solid solutions strengthening from the intermixing of the Fe and Ni increased the interface strength,beyond the sum of parts.The research offers a new route for producing high-quality steel-nickel dissimilar structures and widens the design opportunities of monolithic components,with site-specific properties,for specific structural or functional applications.

Microstructure and properties of Al–7Si–0.6Mg alloys with different Ti contents deposited by wire arc additive manufacturing

Numerous studies have addressed the advantages of wire arc additive manufacturing for manufacturing aluminum alloys. However, the role of Ti content in aluminum alloys has rarely been discussed. Herein, the effect of Ti content on the microstructure and properties of Al–7 Si–0.6 Mg alloys was studied. The alloys were deposited via wire arc additive manufacturing and were examined through optical microscopy(OM), scanning electron microscopy(SEM), and electronic universal testing. The results show that the increase of Ti content gradually promotes the increase of the secondary dendrite arm spacing and also has an increasing tendency to form pores defect in the as-deposited alloys. The change of titanium content also affects the difference between horizontal and vertical direction properties of the alloy. The alloy with a Ti content of 0.112 wt% exhibits the best comprehensive properties. There is no difference in its horizontal and vertical direction properties. The tensile strengths, yield strengths, and elongation of this alloy(T6) along the vertical and horizontal axis are 356 and 355 MPa, 307 and308 MPa, and 8.5% and 8.0%, respectively.

Effect of grain refinement induced by wire and arc additive manufacture (WAAM) on the corrosion behaviors of AZ31 magnesium alloy in NaCl solution

Additive manufacturing(AM)of Mg alloys has become a promising strategy for producing complex structures,but the corrosion performance of AM Mg components remains unexploited.In this study,wire and arc additive manufacturing(WAAM)was employed to produce single AZ31 layer.The results revealed that the WAAM AZ31 was characterized by significant grain refinement with non-textured crystallographic orientation,similar phase composition and stabilized corrosion performance comparing to the cast AZ31.These varied corrosion behaviors were principally ascribed to the size of grain,where cast AZ31 and WAAM AZ31 were featured by micro galvanic corrosion and intergranular corrosion,respectively.

Microstructure and mechanical properties of high-strength low alloy steel by wire and arc additive manufacturing

A high-building multi-directional pipe joint(HBMDPJ)was fabricated by wire and arc additive manufacturing using high-strength low-alloy(HSLA)steel.The microstructure characteristics and transformation were observed and analyzed.The results show that the forming part includes four regions.The solidification zone solidifies as typical columnar crystals from a molten pool.The complete austenitizing zone forms from the solidification zone heated to a temperature greater than 1100℃,and the typical columnar crystals in this zone are difficult to observe.The partial austenitizing zone forms from the completely austenite zone heated between Ac1(austenite transition temperature)and1100℃,which is mainly equiaxed grains.After several thermal cycles,the partial austenitizing zone transforms to the tempering zone,which consistes of fully equiaxed grains.From the solidification zone to the tempering zone,the average grain size decreases from 75 to20μm.The mechanical properties of HBMDPJ satisfies the requirement for the intended application.

Determination of Surface Roughness in Wire and Arc Additive Manufacturing Based on Laser Vision Sensing

Wire and arc additive manufacturing(WAAM) shows a great promise for fabricating fully dense metal parts by means of melting materials in layers using a welding heat source. However, due to a large layer height produced in WAAM, an unsatisfactory surface roughness of parts processed by this technology has been a key issue. A methodology based on laser vision sensing is proposed to quantitatively calculate the surface roughness of parts deposited by WAAM.Calibrations for a camera and a laser plane of the optical system are presented. The reconstruction precision of the laser vision system is verified by a standard workpiece. Additionally, this determination approach is utilized to calculate the surface roughness of a multi-layer single-pass thin-walled part. The results indicate that the optical measurement approach based on the laser vision sensing is a simple and effective way to characterize the surface roughness of parts deposited by WAAM. The maximum absolute error is less than 0.15 mm. The proposed research provides the foundation for surface roughness optimization with different process parameters.

Formability,microstructure evolution and mechanical properties of wire arc additively manufactured AZ80M magnesium alloy using gas tungsten arc welding

Wire arc additive manufacturing(WAAM)technology has been used to fabricate the multi-layer single-pass deposited wall of AZ80M magnesium(Mg)alloy by gas tungsten arc welding.The formability,thermal cycles,microstructural evolution and mechanical properties of the WAAM AZ80M Mg alloy were investigated.The results show that there was significant difference in the temperature variation and the geometries between the original several layers and the subsequent deposited layers.Owing to the arc energy input,the interpass temperature rised rapidly and then stabilized at 150℃.As a result,the width of the deposited wall increased and then kept stable.There were obvious differences in the microstructure of the WAAM AZ80M Mg alloy among the top zone,intermediate zone and bottom zone of deposited wall.During the arc deposition process,theβphase of the WAAM AZ80M Mg alloy redissolved due to the cyclic heat accumulation,and then precipitated in the grain boundary.The cyclic heat accumulation also led to weakening of dendrite segregation.From the substrate to the top zone,the hardness of the deposited wall decreased gradually,and the intermediate zone which was the main body of deposited wall had relatively uniform hardness.The tensile properties of the WAAM AZ80M Mg alloy were different between the vertical direction and the horizontal direction.And the maximum ultimate tensile strength of the WAAM AZ80M Mg alloy was 308 MPa which was close to that of the as-extruded AZ80M Mg alloy.

Microstructure and Mechanical Properties of Wire + Arc Additively Manufactured 2050 Al–Li Alloy Wall Deposits

Aluminum–Lithium(Al–Li) alloy is a topic of great interest owing to its high strength and light weight, but there are only a few applications of Al–Li alloy in wire ss, a special AA2050 Al–Li alloy + arc additive manufacturing(WAAM) process. To identify its feasibility in WAAM procewire was produced and employed in the production of straight-walled components, using a WAAM system based on variable polarity gas tungsten arc welding(VP-GTAW) process. The influence of post-deposited heat treatment on the microstructure and property of the deposit was investigated using optical micrographs(OM), scanning electron microscopy(SEM), X-ray diffraction(XRD), hardness and tensile properties tests. Results revealed that the microstructures of AA2050 aluminum deposits varied with their location layers. The upper layers consisted of fine equiaxed grains, while the bottom layer exhibited a coarse columnar structure. Mechanical properties witnessed a significant improvement after post-deposited heat treatment, with the average micro-hardness reaching 141 HV and the ultimate tensile strength exceeding 400 MPa. Fracture morphology exhibited a typical ductile fracture.

Wire Arc Additive Manufactured CuMn_(13)Al_(7)High-Manganese Aluminium Bronze

In this work,high-manganese aluminium bronze CuMn_(13)Al_(7)samples were prepared by arc additive manufacturing technology.The phase composition,microstructure,and crystal structure of the high-manganese aluminium bronze CuMn_(13)Al_(7)arc additive manufactured samples were analysed using direct-reading spectrometer,metallographic microscope,scanning electron microscope,and transmission electron microscope.The micro-hardness tester,tensile tester,impact tester,and electrochemical workstation were also used to test the performance of the CuMn_(13)Al_(7)samples.By studying the microstructure and properties of the CuMn_(13)Al_(7)samples,it was found that preparation of the samples by the arc additive manufacturing technology ensured good forming quality,almost no defects,and good metallurgical bonding inside the sample.The metallographic structure(α+β+point phase)mainly comprises the following:the metallographic structure in the equiaxed grain region has an obvious grain boundaryα;the metallographic structure in the remelting region has no obvious grain boundaryα;the thermal influence on the metallographic structure produced a weaker grain boundaryαthan the equiaxed grain region.The transverse and longitudinal cross sections of the sample had uniform microhardness distributions,and the average microhardness values were 190.5 HV0.1 and 192.7 HV0.1,respectively.The sample also had excellent mechanical properties:yield strength of 301 MPa,tensile strength of 633 MPa,elongation of 43.5%,reduction of area by 58%,Charpy impact value of 68 J/cm^(2)at–20℃,and dynamic potential polarisation curve test results.Further,it was shown that the average corrosion potential of the sample was–284.5 mV,and the average corrosion current density was 4.1×10–3 mA/cm^(2).

Solidification microstructure evolution and its correlations with mechanical properties and damping capacities of Mg-Al-based alloy fabricated using wire and arc additive manufacturing

Magnesium(Mg)alloys,as the lightest metal structural material with good damping capacities,have im-portant application prospects in realizing structural lightweight and vibration reduction.However,their engineering application is greatly limited by poor plastic formability.Wire and arc additive manufactur-ing(WAAM)provides a potential approach for fabricating large-scale Mg alloy components with high manufacturing flexibility.In this study,the evolution of the solidification microstructure of a WAAM-processed Mg-Al-based alloy was quantitatively analyzed based on the analytical models;then,the cor-relations between the solidification microstructure and mechanical properties/damping capacities were investigated.The results revealed that the WAAM-processed Mg-Al-based alloy with an equiaxed-grain-dominated microstructure displayed a simultaneous enhancement in mechanical properties and damping capacities compared to those of the cast Mg-Al-based alloy.The good combination of mechanical prop-erties and damping capacities are mainly attributed to the weakened basal texture with a relatively high Schmid factor for basalslip,the twinning-induced plasticity(TWIP)effect associated with the profuse{10-12}tensile twinning,and the relatively high dislocation density caused by the thermal stress during the WAAM process.

Wire and arc additive manufacturing of dissimilar 2319 and 5B06 aluminum alloys

Aluminum alloy is the most widely used light alloy at present.By combining different types of aluminum alloys,their functional properties can be expanded.In the present research,two components composed of 2319(Al-6.5Cu)and 5B06(Al-6.4Mg)dissimilar alloys were fabricated by wire and arc additive manufacturing(WAAM).The deposited component with the bottom half of 2319 and the top half of 5B06 exhibits better mechanical properties than its counterpart deposited vice versa.Its ultimate tensile strength,yield strength,and elongation are 258.5 MPa,139.3 MPa,and 5.6%,respectively,which are only slightly inferior to the mechanical properties of 2319 base metal.The results show that for both components,fracture occurred at a layer thickness above the interface layer during the tensile test,regardless of the deposition order.It appears that the thermal stress due to the long dwell time and the remelting of the S-AlCu Mg phase are the main factors promoting crack initiation.Depending on the deposition order,cracks propagate either along the aggregated pores or stripθ-AlCu phase distributed along the grain boundary.By analyzing the heat input and selecting the appropriate depositing order,the strength of WAAM dissimilar aluminum alloys can be effectively improved through the proper control of microstructure and internal defects.

基于PSO-BP神经网络的双相不锈钢电弧增材制造焊道成形预测

Duplex stainless steel was formed through welding wire and arc additive manufacturing(WAAM)using tungsten inert gas.The effects of wire feeding speed(WFS),welding speed(WS),welding current,and their interaction on the weld bead width and height were discussed.Back-propagation(BP)neural network algorithm prediction model was established by taking the bead width and height as the output layer,and the network weight and threshold values were optimized using the particle swarm optimization(PSO)algorithm to obtain the prediction model of bead width and height.The predicted results were verified by experiments.Results show that the weld bead width increases with the increase in WFS and the welding current and decreases with WS.The smaller the WFS,the faster the WS,which is beneficial for the generation of equiaxed crystals.The smaller the welding current,the faster the cooling speed of the metal melt,which is conducive to the formation of dendrites.The interaction among WS,wire feed speed,and welding current has a significant effect on the bead width.The weld bead height is positively correlated with the wire feed speed and negatively correlated with the WS and current.The interaction between the wire feed speed and WS is significant.The optimized WAAM process parameters for duplex stainless steel are a wire feed speed of 200 cm/min,WS of 24 cm/min,and welding current of 160 A.The maximum error of the BP neural network in predicting the weld bead width and height is 7.74%,and the maximum error between the predicted and experimental values of the BP-PSO neural network is 4.27%.This finding indicates that the convergence speed is fast,improving the prediction accuracy.