Decoupling of temporal/spatial broadening effects in Doppler wind LiDAR by 2D spectral analysis

Pulse echo accumulation is commonly employed in coherent Doppler wind LiDAR(light detection and ranging)under the assumption of steady wind.Here,the measured spectral data are analyzed in the time dimension and frequency dimension to cope with the temporal wind shear and achieve the optimal accumulation time.A hardware-efficient algorithm combining the interpolation and cross-correlation is used to enhance the wind retrieval accuracy by reducing the frequency sampling interval and then reduce the spectral width calculation error.Moreover,the temporal broadening effect and spatial broadening effect are decoupled according to the strategy we developed.

Whole-volume histogram analysis of spectral-computed tomography iodine maps characterizes HER2 expression in gastric cancer

BACKGROUND Although surgery remains the primary treatment for gastric cancer(GC),the identification of effective alternative treatments for individuals for whom surgery is unsuitable holds significance.HER2 overexpression occurs in approximately 15%-20%of advanced GC cases,directly affecting treatment-related decisions.Spectral-computed tomography(sCT)enables the quantification of material compositions,and sCT iodine concentration parameters have been demonstrated to be useful for the diagnosis of GC and prediction of its invasion depth,angioge-nesis,and response to systemic chemotherapy.No existing report describes the prediction of GC HER2 status through histogram analysis based on sCT iodine maps(IMs).AIM To investigate whether whole-volume histogram analysis of sCT IMs enables the prediction of the GC HER2 status.METHODS This study was performed with data from 101 patients with pathologically confirmed GC who underwent preoperative sCT examinations.Nineteen parameters were extracted via sCT IM histogram analysis:The minimum,maximum,mean,standard deviation,variance,coefficient of variation,skewness,kurtosis,entropy,percentiles(1st,5th,10th,25th,50th,75th,90th,95th,and 99th),and lesion volume.Spearman correlations of the parameters with the HER2 status and clinicopathological parameters were assessed.Receiver operating characteristic curves were used to evaluate the parameters’diagnostic performance.RESULTS Values for the histogram parameters of the maximum,mean,standard deviation,variance,entropy,and percentiles were significantly lower in the HER2+group than in the HER2–group(all P<0.05).The GC differentiation and Lauren classification correlated significantly with the HER2 status of tumor tissue(P=0.001 and 0.023,respectively).The 99th percentile had the largest area under the curve for GC HER2 status identification(0.740),with 76.2%,sensitivity,65.0%specificity,and 67.3%accuracy.All sCT IM histogram parameters correlated positively with the GC HER2 status(r=0.237-0.337,P=0.001-0.017).CONCLUSION Whole-lesion histogram parameters derived from sCT IM analysis,and especially the 99th percentile,can serve as imaging biomarkers of HER2 overexpression in GC.

Observation and Analysis of VLF Nocturnal Multimode Interference Phenomenon based on Waveguide Mode Theory

Very low frequency(VLF)signals are propagated between the ground-ionosphere.Multimode interference will cause the phase to show oscillatory changes with distance while propagating at night,leading to abnormalities in the received VLF signal.This study uses the VLF signal received in Qingdao City,Shandong Province,from the Russian Alpha navigation system to explore the multimode interference problem of VLF signal propagation.The characteristics of the effect of multimode interference phenomena on the phase are analyzed according to the variation of the phase of the VLF signal.However,the phase of VLF signals will also be affected by the X-ray and energetic particles that are released during the eruption of solar flares,therefore the two phenomena are studied in this work.It is concluded that the X-ray will not affect the phase of VLF signals at night,but the energetic particles will affect the phase change,and the influence of energetic particles should be excluded in the study of multimode interference phenomena.Using VLF signals for navigation positioning in degraded or unavailable GPS conditions is of great practical significance for VLF navigation systems as it can avoid the influence of multimode interference and improve positioning accuracy.

Numerical analysis of matrix swelling and its effect on microstructure of digital coal and its associated permeability during CO_(2)-ECBM process based on X-ray CT data

Matrix swelling effect will cause the change of microstructure of coal reservoir and its permeability,which is the key factor affecting the engineering effect of CO_(2)-ECBM technology.The Sihe and Yuwu collieries are taken as research objects.Firstly,visualization reconstruction of coal reservoir is realized.Secondly,the evolution of the pore/fracture structures under different swelling contents is discussed.Then,the influence of matrix phase with different swelling contents on permeability is discussed.Finally,the mechanism of swelling effect during the CO_(2)-ECBM process is further discussed.The results show that the intra-matrix pores and matrix-edge fractures are the focus of this study,and the contacting area between matrix and pore/fracture is the core area of matrix swelling.The number of matrix particles decreases with the increase of size,and the distribution of which is isolated with small size and interconnected with large size.The swelling effect of matrix particles with larger size has a great influence on the pore/fracture structures.The number of connected pores/fractures is limited and only interconnected in a certain direction.With the increase of matrix swelling content,the number,porosity,width,fractal dimension,surface area and volume of pores/fractures decrease,and their negative contribution to absolute permeability increases from 0.368% to 0.633% and 0.868%-1.404%,respectively.With the increase of swelling content,the number of intra-matrix pores gradually decreases and the pore radius becomes shorter during the CO_(2)-ECBM process.The matrix continuously expands to the connected fractures,and the width of connected fractures gradually shorten.Under the influence of matrix swelling,the bending degree of fluid flow increases gradually,so the resistance of fluid migration increases and the permeability gradually decreases.This study shows that the matrix swelling effect is the key factor affecting CBM recovery,and the application of this effect in CO_(2)-ECBM process can be discussed.

Elemental composition x-ray fluorescence analysis with a TES-based high-resolution x-ray spectrometer

The accurate analysis of the elemental composition plays a crucial role in the research of functional materials.The emitting characteristic x-ray fluorescence(XRF)photons can be used for precisely discriminating the specified element.The detection accuracy of conventional XRF methodology using semiconductor detector is limited by the energy resolution,thus posing a challenge in accurately scaling the actual energy of each XRF photon.We adopt a novel high-resolution x-ray spectrometer based on the superconducting transition-edge sensor(TES)for the XRF spectroscopy measurement of different elements.Properties including high energy resolution,high detection efficiency and precise linearity of the new spectrometer will bring significant benefits in analyzing elemental composition via XRF.In this paper,we study the Ledge emission line profiles of three adjacent rare earth elements with the evenly mixed sample of their oxide components:terbium,dysprosium and holmium.Two orders of magnitude better energy resolution are obtained compared to a commercial silicon drift detector.With this TES-based spectrometer,the spectral lines overlapped or interfered by background can be clearly distinguished,thus making the chemical component analysis more accurate and quantitative.A database of coefficient values for the line strength of the spectrum can then be constructed thereafter.Equipped with the novel XRF spectrometer and an established coefficient database,a direct analysis of the composition proportion of a certain element in an unknown sample can be achieved with high accuracy.

X-ray Manifestations of Pneumoconiosis Patients and Differential Analysis with Pulmonary Tuberculosis

[Objectives]This study was conducted to explore the X-ray manifestations of pneumoconiosis patients and differentiation from pulmonary tuberculosis.[Methods]Retrospective analysis was conducted on 103 patients who underwent lung examinations,including 47 cases of pneumoconiosis and 56 cases of pulmonary tuberculosis.The differences in nodule characteristics and accompanying cavity sign between pneumoconiosis and pulmonary tuberculosis were compared.[Results]The X-ray manifestations of pneumoconiosis patients mainly included various forms of lung images,which were uneven in density,and had blurry edges,and sometimes thickening of lung markings and reduction of lung volume could be observed.The acinar nodules observed in X-ray films of patients with hematogenous disseminated pulmonary tuberculosis appeared petal like.The uniformity of nodule appearance such as nodule distribution,nodule density,and nodule size was significantly lower in pneumoconiosis than in hematogenous disseminated pulmonary tuberculosis,showing a statistical significance(P<0.05).The diameter of cavities in patients with pneumoconiosis accompanied by cavity sign[(0.64±0.13 vs 3.37±0.95)cm]was lower than that in patients with secondary pulmonary tuberculosis accompanied by cavity sign.There was a significant difference in the thickness of the cavity wall between the two diseases,and patients with pneumoconiosis accompanied by cavity sign had a higher rate of thick wall cavities(>3 mm).The X-ray manifestations of pneumoconiosis and tuberculosis were relatively similar,but the distribution,density and size of nodules in pneumoconiosis were relatively uneven,and the patients accompanied by cavity sign had smaller cavity diameter and higher rate of thick-walled cavities.[Conclusions]This study provides a reference for the clinical differential diagnosis of pneumoconiosis and pulmonary tuberculosis.

Energy-dispersive X-ray Spectroscopy for the Quantitative Analysis of Pyrite Thin Specimens

To explore ways to improve the accuracy of quantitative analysis of samples in the micrometer to nanometer range of magnitudes,we adopted analytical transmission electron microscopy(AEM/EDS)for qualitative and quantitative analysis of pyrite materials.Additionally,the k factor of pyrite is calculated experimentally.To develop an appropriate non-standard quantitative analysis model for pyrite materials,the experimentally calculated k factor is compared with that estimated from the non-standard quantitative analytical model of the instrument software.The experimental findings demonstrate that the EDS attached to a TEM can be employed for precise quantitative analysis of micro-and nanoscale regions of pyrite materials.Furthermore,it serves as a reference for improving the results of the EDS quantitative analysis of other sulfides.

Low-dimensional multi-spectral space for color reproduction based on nonnegative constrained principal component analysis

In order to overcome the shortcomings that the reconstructed spectral reflectance may be negative when using the classic principal component analysis （PCA）to reduce the dimensions of the multi-spectral data, a nonnegative constrained principal component analysis method is proposed to construct a low-dimensional multi-spectral space and accomplish the conversion between the new constructed space and the multispectral space. First, the reason behind the negative data is analyzed and a nonnegative constraint is imposed on the classic PCA. Then a set of nonnegative linear independence weight vectors of principal components is obtained, by which a lowdimensional space is constructed. Finally, a nonlinear optimization technique is used to determine the projection vectors of the high-dimensional multi-spectral data in the constructed space. Experimental results show that the proposed method can keep the reconstructed spectral data in [ 0, 1 ]. The precision of the space created by the proposed method is equivalent to or even higher than that by the PCA.

In situ analysis of multi-twin morphology and growth using synchrotron polychromatic X-ray microdiffraction

Synchrotron polychromatic X-ray microdiffraction（micro-XRD） was applied to study in situ deformation twinning of commercially AZ31（Mg-3Al-1Zn） strip subjected to uniaxial tension.The morphology and growth of twins were analyzed in situ under the load level from 64 to 73 MPa.The X-ray microdiffraction data,collected on beamline 12.3.2 at the Advanced Light Source,were then used to map an area of 396μm x 200μm within the region of interest.The experimental set-up and X-ray diffraction microscopy with a depth resolution allow the position and orientation of each illuminated grain to be determined at the submicron size.A list of parent grains sorted by crystallographic orientation were selected to examine their twinning behavior.The results depict twin variant selection,local misorientation fluctuation and mosaic spread for multi-twins within the same parent grain.As load increases,the amplitude of misorientation fluctuation along twin trace keeps increasing.This is attributable to the accumulation of geometrically necessary dislocations.

Ice-Induced Fatigue Analysis by Spectral Approach for Offshore Jacket Platforms with Ice-Breaking Cones

The spectral methods and ice-induced fatigue analysis are discussed based on Miner＇s linear cumulative fatigue hypothesis and S-N curve data. According to the long-term data of full-scale tests on the platforms in the Bohai Sea, the ice force spectrum of conical structures and the fatigue environmental model are established. Moreover, the finite element model of JZ20-2MSW platform, an example of ice-induced fatigue analysis, is built with ANSYS software. The mode analysis and dynamic analysis in frequency domain under all kinds of ice fatigue work conditions are carded on, and the fatigue life of the structure is estimated in detail. The methods in this paper can be helpful in ice-induced fatigue analysis of ice-resistant platforms.

Geochemical analysis of marine sediments using fused glass disc by X-ray fluorescence spectrometry

A method was developed for content determination of Na, Mg, A1, Si, P,S, C1, K, Ca, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, Ga, Nb, Zr, Y, Sr, Rb, Ba, La and Ce etc. covering 26 major, minor, and trace elements in marine sediment samples using fused glass disc by X-ray Fluorescence spectrometry. Calibration was made using marine sediment certified reference materials and the synthetic standard samples prepared by mixing several marine sediments with stream sediment and carbonate standard samples in different proportions. The matrix effect was corrected using theoretical alpha coefficients, experience coefficients and the scattered radiation as the internal standard （for the trace elements）. The accuracy of the method was evaluated by analysis of certified reference materials GBW07314, GBW07334 and GSMS6. The results are in good agreement with the certified values of the standards with RSD less than 2.60%, except for Y, Cr, Ga, Ce, La, Nb, Rb, and V with RSD less than 9.0% （n=12）.

Elemental and proximate analysis of coal by x-ray fluorescence assisted laser-induced breakdown spectroscopy

Although laser-induced breakdown spectroscopy(LIBS),as a fast on-line analysis technology,has great potential and competitiveness in the analysis of chemical composition and proximate analysis results of coal in thermal power plants,the measurement repeatability of LIBS needs to be further improved due to the difficulty in controlling the stability of the generated plasmas at present.In this paper,we propose a novel x-ray fluorescence(XRF) assisted LIBS method for high repeatability analysis of coal quality,which not only inherits the ability of LIBS to directly analyze organic elements such as C and H in coal,but also uses XRF to make up for the lack of stability of LIBS in determining other inorganic ash-forming elements.With the combination of elemental lines in LIBS and XRF spectra,the principal component analysis and the partial least squares are used to establish the prediction model and perform multi-elemental and proximate analysis of coal.Quantitative analysis results show that the relative standard deviation(RSD) of C is 0.15%,the RSDs of other elements are less than 4%,and the standard deviations of calorific value,ash content,sulfur content and volatile matter are 0.11 MJ kg,0.17%,0.79% and 0.41%respectively,indicating that the method has good repeatability in determination of coal quality.This work is helpful to accelerate the development of LIBS in the field of rapid measurement of coal entering the power plant and on-line monitoring of coal entering the furnace.

CALCULATING RESPONSE SPECTRAL MOMENTS BY COMPLEX MODAL ANALYSIS

Response spectral moments are useful for system reliability analysis.Usually,spectral mo- ments are calculated by the frequency domain method.Based on the time domain modal analysis of random vibrations,the authors present a new method for calculating response spectral moments through response correlation functions.The method can be applied to both classical and non-classical damping cases and to three kinds of random excitations,i.e.,white noise,band-limited white noise, and filtered white noise.

Study on the application of spectral fatigue analysis

Fatigue failure has long been an important issue for ships and offshore structures. Among the numerous methods for predicting fatigue life, the spectral method is accepted as the most reliable. Although the theory behind spectral analysis is straight-forward, the analysis itself is complicated and time-consuming because it is closely related to critical technical details such as the application of fatigue loading (wave pressures and the inertial forces due to cargoes), the extraction of the stress, and the calculation of stress RAO. Here, four key technical details-loading application, displacement boundary condition, the calculation of stress RAO, and the extraction of the fatigue stress-are discussed thoroughly. For each aspect, a resolution is presented based on the finite element pre-and post-processing software MSC/PATRAN or FE solver MSC/NASTRAN. The resolutions are effective and efficient, which can help engineers perform spectral fatigue analysis accurately and faster.

Timescale Analysis of Spectral Lags

A technique for timescale analysis of spectral lags performed directly in the time domain is developed. Simulation studies are made to compare the time domain technique with the Fourier frequency analysis for spectral time lags. The time domain technique is applied to studying rapid variabilities of X-ray binaries and γ-ray bursts. The results indicate that in comparison with the Fourier analysis the timescale analysis technique is more powerful for the study of spectral lags in rapid variabilities on short time scales and short duration flaring phenomena.

Use of high-resolution X-ray computed tomography and 3D image analysis to quantify mineral dissemination and pore space in oxide copper ore particles

Mineral dissemination and pore space distribution in ore particles are important features that influence heap leaching performance. To quantify the mineral dissemination and pore space distribution of an ore particle, a cylindrical copper oxide ore sample (I center dot 4.6 mm x 5.6 mm) was scanned using high-resolution X-ray computed tomography (HRXCT), a nondestructive imaging technology, at a spatial resolution of 4.85 mu m. Combined with three-dimensional (3D) image analysis techniques, the main mineral phases and pore space were segmented and the volume fraction of each phase was calculated. In addition, the mass fraction of each mineral phase was estimated and the result was validated with that obtained using traditional techniques. Furthermore, the pore phase features, including the pore size distribution, pore surface area, pore fractal dimension, pore centerline, and the pore connectivity, were investigated quantitatively. The pore space analysis results indicate that the pore size distribution closely fits a log-normal distribution and that the pore space morphology is complicated, with a large surface area and low connectivity. This study demonstrates that the combination of HRXCT and 3D image analysis is an effective tool for acquiring 3D mineralogical and pore structural data.

Application of Wavelet Algorithm to Spectral Analysis of Oceanic Waves and Offshore Structure Responses

Fourier transform （FF） is a commonly used method in spectral analysis of ocean wave and offshore structure responses, but it is not suitable for records of short length. In this paper another method, wavelet transform （WT）, is applied to ＇analyze the data of short length. The Morlet wavelet is employed to calculate the spectra density functions for wave records and simulated Floating Production Storage and Offloading （FPSO） vessels＇ responses. Computed wave data include simulated wave data based on JONSWAP spectrum and the recorded data of Storm 149 from North Alwyn. Wavelet method is validated by comparing the statistical characteristics by WF method and those by fast Fourier transform （FFT） method with those of target spectra. The spectral density fnnctions＇ shapes calculated by WT are less malformed and have less error of statistical characteristics compared with those by FT especially when the record lengths decrease.

Quantitative energy-dispersive X-ray fluorescence analysis for unknown samples using full-spectrum least-squares regression

The full-spectrum least-squares(FSLS) method is introduced to perform quantitative energy-dispersive X-ray fluorescence analysis for unknown solid samples.Based on the conventional least-squares principle, this spectrum evaluation method is able to obtain the background-corrected and interference-free net peaks, which is significant for quantization analyses. A variety of analytical parameters and functions to describe the features of the fluorescence spectra of pure elements are used and established, such as the mass absorption coefficient, the Gi factor, and fundamental fluorescence formulas. The FSLS iterative program was compiled in the C language. The content of each component should reach the convergence criterion at the end of the calculations. After a basic theory analysis and experimental preparation, 13 national standard soil samples were detected using a spectrometer to test the feasibility of using the algorithm. The results show that the calculated contents of Ti, Fe, Ni, Cu, and Zn have the same changing tendency as the corresponding standard content in the 13 reference samples. Accuracies of 0.35% and 14.03% are obtained, respectively, for Fe and Ti, whose standard concentrations are 8.82% and 0.578%, respectively. However, the calculated results of trace elements (only tens of lg/g) deviate from the standard values. This may be because of measurement accuracy and mutual effects between the elements.

MULTI-PEAK MATCH INTENSITY RATIO METHOD OF QUANTI-TATIVE X-RAY DIFFRACTION PHASE ANALYSIS

A new method for quantitative phase analysis is proposed by using X-ray diffraction multi-peak match intensity ratio. This method can obtain the multi-peak match intensity ratio among each phase in the mixture sample by using all diffraction peak data in the mixture sample X-ray diffraction spectrum and combining the relative intensity distribution data of each phase standard peak in JCPDS card to carry on the least square method regression analysis. It is benefit to improve the precision of quantitative phase analysis that the given single line ratio which is usually adopted is taken the place of the multi-peak match intensity ratio and is used in X-ray diffraction quantitative phase analysis of the mixture sample. By analyzing four-group mixture sample, adopting multi-peak match intensity ratio and X-ray diffraction quantitative phase analysis principle of combining the adiabatic and matrix flushing method, it is tested that the experimental results are identical with theory.

Unsupervised seismic facies analysis using sparse representation spectral clustering

Traditional unsupervised seismic facies analysis techniques need to assume that seismic data obey mixed Gaussian distribution.However,fi eld seismic data may not meet this condition,thereby leading to wrong classifi cation in the application of this technology.This paper introduces a spectral clustering technique for unsupervised seismic facies analysis.This algorithm is based on on the idea of a graph to cluster the data.Its kem is that seismic data are regarded as points in space,points can be connected with the edge and construct to graphs.When the graphs are divided,the weights of the edges between the different subgraphs are as low as possible,whereas the weights of the inner edges of the subgraph should be as high as possible.That has high computational complexity and entails large memory consumption for spectral clustering algorithm.To solve the problem this paper introduces the idea of sparse representation into spectral clustering.Through the selection of a small number of local sparse representation points,the spectral clustering matrix of all sample points is approximately represented to reduce the cost of spectral clustering operation.Verifi cation of physical model and fi eld data shows that the proposed approach can obtain more accurate seismic facies classification results without considering the data meet any hypothesis.The computing efficiency of this new method is better than that of the conventional spectral clustering method,thereby meeting the application needs of fi eld seismic data.