Suppression of low-frequency ultrasound broadband vibration using star-shaped single-phase metamaterials

In order to suppress the low-frequency ultrasound vibration in the broadband range of 20 k Hz—100 k Hz,this paper proposes and discusses an acoustic metamaterial with low-frequency ultrasound vibration attenuation properties,which is configured by hybrid arc and sharp-angle convergent star-shaped lattices.The effect of the dispersion relation and the bandgap characteristic for the scatterers in star-shaped are simulated and analyzed.The target bandgap width is extended by optimizing the geometry parameters of arc and sharp-angle convergent lattices.The proposed metamaterial configured by optimized hybrid lattices exhibits remarkable broad bandgap characteristics by bandgap complementarity,and the simulation results verify a 99%vibration attenuation amplitude can be obtained in the frequency of20 k Hz—100 k Hz.After the fabrication of the proposed hybrid configurational star-shaped metamaterial by 3D printing technique,the transmission loss experiments are performed,and the experimental results indicate that the fabricated metamaterial has the characteristics of broadband vibration attenuation and an amplitude greater than 85%attenuation for the target frequency.These results demonstrate that the hybrid configurational star-shaped metamaterials can effectively widen the bandgap and realize high efficiency attenuation,which has capability for the vibration attenuation in the application of highprecise equipment.

基于Y-shaped路网的早高峰拼车定价策略

针对交通资源配置有限导致的早高峰通勤拥堵问题,借鉴共享经济理论,引入拼车出行概念,充分考虑通勤者出行方式和Y-shaped路网特点,建立了基于通勤者出行效益的拼车定价模型.模型结合费用补偿机制,讨论了以平台利润最大化和系统负效用最小化为目标的拼车定价策略,并给出了定价策略有效的阈值条件.研究结果表明,当通勤者都参与到拼车服务中时,拼车平台利润和交通系统负效用在其相应拼车定价策略下均能达到最优值,并且以交通系统负效用最小化为目标的拼车定价策略能消除Y-shaped路网中瓶颈处的交通拥堵.

Gastrotracheal fistula:Treatment with a covered self-expanding Y-shaped metallic stent

A 67-year-old man had a sev-ere cough and pulmonary infection for 1 wk before seeking evaluation at our hospital.He had undergone esophagectomy with gastric pull-up and radiotherapy for esophageal cancer 3 years previously.After admission to our hospital,gastroscopy and bronchoscopy revealed a fistulous communication between the posterior tracheal wallnear the carina and the upper residual stomach.We measured the diameter of the trachea and bronchus and determined the site and size of the fistula using multislice computed tomography and gastroscopy.A covered self-expanding Y-shaped metallic stent was implanted into the trachea and bronchus.Subsequently,the fistula was closed completely.The patient tolerated the stent well and had good palliation of his symptoms.

Synthesis and characterization of novel star-shaped pyridine cored compounds with alternating carbazole and triphenylamine moieties

Amorphous 2,4,6-trissubstituted pyridines containing three peripheral carbazole or two triphenylamine and one carbazole moieties, respectively, have been synthesized and characterized. The properties of the compounds are investigated by UV-vis absorption, photoluminescence spectroscopy, thermal analysis as well as cyclic voltammetry. The results show that the compounds have high thermal stability, emit blue light. Also, the compounds possess the HOMO and LUMO energy levels comparable to those of NPB. The effects of different substituents on the electronic properties of the materials have been discussed.

SYNTHESIS OF HETEROARM STAR-SHAPED POLYMER BY THE USE OF POLYFUNCTIONAL CHAIN-TRANSFER AGENT via CONVENTIONAL FREE RADICAL POLYMERIZATION

Heteroarm star-shaped polymers were synthesized by conventional free radical polymerization in two steps by the use of polyfunctional chain transfer agent.In the first step,free radical polymerization of methyl methacrylate was carried out in the presence of a polyfunctional chain transfer agent,pentaerythritol tetrakis(3-mercaptopropinate).At appropriate monomer conversions,two-arm PMMA having two residual thiol groups at the chain center or three-arm PMMA having one residual thiol group at the core were o...

Fiber-based joint time and frequency dissemination via star-shaped commercial telecommunication network

A fiber-based, star-shaped joint time and frequency dissemination scheme is demonstrated. By working in cooperation with the existing commercial telecommunication network. Our scheme enables the frequency, time, and digital data networks to be integrated together and could represent an ideal option of interconnection among scientific institutions.The compensation functions of the time and frequency transfer scheme are set at the client nodes. The complexity of the central node is thus reduced, and future expansion by the addition of further branches will be accomplished more easily.During a performance test in which the ambient temperature fluctuation is 30℃/day, timing signal dissemination stability is achieved to be approximately ±50 ps along 25-km-long fiber spools. After calibration, a timing signal synchronization accuracy of 100 ps is also realized. The proposed scheme offers an option of the construction of large-scale fiber-based frequency and time transfer networks.

Y-shaped block copolymers of poly(ethylene glycol) and poly(N-isopropylacrylamide) synthesized by ATRP

Novel Y-shaped block copolymers of poly（ethylene glycol） and poly（N-isopropylacrylamide）, PEG-b-（PNIPAM）2, were successfully synthesized through atom transfer radical polymerization （ATRP）. A difunctional macroinitiator was prepared by esterification of 2,2-dichloroacetyl chloride with poly（ethylene glycol） monomethyl ether （PEG）. The copolymers were obtained via the ATRP ofN-isopropylacrylamide （NIPAM） at 30℃ with CuCl/Me6TREN as a catalyst system and DMF/H2O （v/v = 3：1） mixture as solvent. The resulting copolymers were characterized by gel permeation chromatography （GPC） and ^1H NMR. These block copolymers show controllable molecular weights and narrow molecular weight distributions （PDI 〈 1.15）. Their phase transition temperatures and the corresponding enthalpy changes in aqueous solution were measured by differential scanning calorimetry （DSC）. As a result, the phase transition temperature of PEG45-b-（PNIPAM55）2 is higher than that of PNIPAM, however, the corresponding enthalpy change is much lower, indicating the significant influence of the macromolecular composition and architecture on the phase transition.

PREPARATION AND CHARACTERIZATION OF INCLUSION COMPLEXES OF TWO-ARM LINEAR AND FOUR-ARM STAR-SHAPED POLY(ε-CAPROLACTONE)S WITHα-CYCLODEXTRIN

Both four-ann star-shaped poly（ε-caprolactone） （4sPCL） and two-ann linear PCL （2LPCL） were synthesized and their inclusion complexation with α-cyclodextrin （α-CD） were studied. The inclusion complexes （ICs） formed between the PCL polymers and α-CD were characterized by ^1H-NMR, DSC, TGA, WAXD, and FT-1R, respectively. Both branch ann number and molecular weight of the PCL polymers have apparent effect on the stoichiometry （CL：CD, mol：mol） of these ICs. All these analytical results indicate that the branch arms of the PCL polymers are incorporated into the hydrophobic α-CD cavities and their original crystalline properties are completely suppressed. Moreover, the inclusion complexation between two-ann linear or four-ann star-shaped PCL polymers and α-CD not only enhances the thermal stability of the guest PCL polymers but also improves that of α-CD.

FIXED POINTS OF NONEXPANSIVE MAPPINGS ON STAR-SHAPED SUBSETS OF A CONVEX METRIC SPACE

In this paper, we give some characteristic properties of star-shaped sets which include a subset of a convex metric space. Using the characteristic properties, we discuss the existence problems of fixed points of nonexpansive type mappings on star-shaped subsets of convex metric spaces, which generalize the recent results obtained by Ding Xie-ping, Beg and Azam. Finally, we give an example which shows that our generalizations are essential.

Star-shaped Differentiable Functions and Star-shaped Differentials

Based on the isomorphism between the space of star-shaped sets and the space of continuous positively homogeneous real-valued functions, the star-shaped differential of a directionally differentiable function is defined. Formulas for star-shaped differential of a pointwise maximum and a pointwise minimum of a finite number of directionally differentiable functions, and a composite of two directionaUy differentiable functions are derived. Furthermore, the mean-value theorem for a directionaUy differentiable function is demonstrated.

Deformation and defects in hydroforming of Y-shaped tubes

Hydroforming process of a Y-shaped stainless steel tube was investigated through numerical simulation and experiments. The forming process and reasons of typical defects were analyzed with three different loading paths. Thickness distribution of formed Y-shaped tube was obtained. It is shown by numerical and experimental results that the transition regions are depressed in the forming condition of low inner pressure and wrinkles occur, while fracture occurs in the forming condition of high inner pressure. After forming, the thickness in left transition fillet region is the largest, that in fight transition fillet region is thinner, and the thinnest thickness is at the top of the protrusion. The original thickness line is below the top of the protrusion. The thinning area occurs above this line, while the thickening area is below this line. The maximum thinning rate is significantly increased as the calibration pressure increases, while the maximum thickening rate remains almost unchanged.

SYNTHESIS,CHARACTERIZATION AND NANOPARTICLE FORMATION OF STAR-SHAPED POLY(L-LACTIDE)WITH SIX ARMS

Well-defined star-shaped poly(L-lactide)with six arms(sPLLA)was synthesized via the ring-opening polymerization of L-lactide using dipentaerythritol as initiator and stannous octoate as catalyst in bulk at 125~C.The effects of molar ratios of both monomer to initiator and monomer to catalyst on the molecular weights of as-synthesized sPLLA polymers were in detail investigated.The molecular weights of sPLLA polymers linearly increased with the molar ratio of monomer to initiator,and the molecular weight dist...

pH-sensitive micelles self-assembled from star-shaped TPGS copolymers with ortho ester linkages for enhanced MDR reversal and chemotherapy

TPGS approved by FDA can be used as a P-gp inhibitor to effectively reverse multi-drug resistance(MDR)and as an anticancer agent for synergistic antitumor effects.However,the comparatively high critical micelle concentration(CMC),low drug loading(DL)and poor tumor target limit its further clinical application.To overcome these drawbacks,the pH-sensitive star-shaped TPGS copolymers were successfully constructed via using pentaerythritol as the initial materials,ortho esters as the pH-triggered linkages and TPGS active-ester as the terminated MDR material.The amphiphilic star-shaped TPGS copolymers could self-assemble into free and doxorubicin(DOX)-loaded micelles at neutral aqueous solutions.The micelles exhibited the lower CMC(8.2×10^(−5) mg/ml),higher DL(10.8%)and long-term storage and circulation stability,and showed enhanced cellular uptake,apoptosis,cytotoxicity,and growth inhibition for in vitro MCF-7/ADR and/or MCF-7/ADR multicellular spheroids and in vivo MCF-7/ADR tumors via efficiently targeted drug release at tumoral intracellular pH(5.0),MDR reversal of TPGS,and synergistic effect of DOX and TPGS.Therefore,the pH-sensitive micelles self-assembled from star-shaped TPGS copolymers with ortho ester linkages are potentially useful to clinically transform for enhanced MDR cancer treatment.

Binary collision approximation for solitary waves in a Y-shaped granular chain

We implement a binary collision approximation to study solitary wave propagation in a two-dimensional double Y- shaped granular chain. The solitary wave was transmitted and reflected when it met the interface of the bifurcated branches of the Y-shaped granular chains. We obtain the analytic results of the ratios of the transmitted and reflected speeds to the incident speed of the solitary wave, the maximum force between the two neighbor beads in a solitary wave, and the total time taken by the pulse to pass through each branch. All of the analytic results are in good agreement with the experimental observations from Daraio et al. [Phys. Rev. E 82 036603 （2010）]. Moreover, we also discuss the delay effects on the arrival of split pulses, and predict the recombination of the split waves traveling in branches in the final stem of asymmetric systems. The prediction of pulse recombination is verified by our numerical results.

Evaluation of ultimate bearing capacity of Y-shaped vibro-pile

Based on Mindlin stress solution, a numerical computational method was proposed to calculate the stresses in the ground induced by side friction and the resistance of Y-shaped vibro-pile. The improved Terzaghi's and ЪерезанцевВГ's methods for ultimate bearing capacity evaluation were proposed by considering the stress strength induced by friction resistance at pile head level of Y-pile. A new method to calculate the ultimate bearing capacity of Y-pile was also proposed based on the assumptions of soil failure mode at the tip of Y-pile and the use of Mohr-Coulomb soil yield criterion and Vesic compressive correction coefficient with the induced stresses in the ground. Based on the comparisons with the field static load test results, it is found that the improved Terzaghi's method gives higher ultimate capacity, while the other two methods shows good agreement with the field results.

Transfer characteristics of dynamic biochemical signals in non-reversing pulsatile flows in a shallow Y-shaped microfluidic channel: signal filtering and nonlinear amplitude-frequency modulation

The transports of the dynamic biochemical signals in the non-reversing pulsatile flows in the mixing microchannel of a Y-shaped microfluidic device are ana- lyzed. The results show that the mixing micro-channel acts as a low-pass filter, and the biochemical signals are nonlinearly modulated by the pulsatile flows, which depend on the biochemical signal frequency, the flow signal frequency, and the biochemical signal transporting distance. It is concluded that, the transfer characteristics of the dynamic biochemical signals, which are transported in the time-varying flows, should be carefully considered for better loading biochemical signals on the cells cultured on the bottom of the microfluidic channel.

Synthesis and Physicochemical Characterization of Biodegradable Star-Shaped Poly Lactide-Co-Glycolide-<i>β</i>-Cyclodextrin Copolymer Nanoparticles Containing Albumin

The purposes of this research were to synthesize and characterize star-shaped poly lactide-co-glycolide-β-cyclo-dextrin (PLGA-β-CD) copolymer by reacting L-lactide, glycolide and β-cyclodextrin in the presence of stannous octoate as a catalyst. The structure of PLGA-β-CD copolymer was confirmed with 1H-NMR, 13C-NMR and FT-IR spectra. Albumin as a model peptide drug was encapsulated within nanoparticles made of PLGA-β-CD with a modified double emulsion method. Transmission electron microscopy (TEM) and scanning electron microscopy (SEM) photomicrographs showed that the nanoparticles have the mean diameter within the range of 80 - 210 nm. Also they were almost spherical in shape. Effects of the experimental parameters, such as copolymer composition, copolymer concentration, and reaction temperature, on particular size and encapsulation efficiency were investigated.

Y-Shaped Intra-Scleral Fixated Lens versus Retro-Pupillary Iris Claw Lens in the Treatment of Aphakia

Background: Many reasons can lead to an aphakia without adequate capsular support for implantation of a posterior chamber intraocular lens (IOL), such as intraoperative unintentional rupture of posterior capsule during phacoemulsification, planned intracapsular cataract extraction, ocular trauma and lens dislocation due to congenital and acquired causes. Purpose: To compare Y-shaped intra-scleral fixation of a posterior chamber IOL with retro pupillary fixation of an iris-claw intraocular lens (IOL) for Aphakic eyes without sufficient capsular support as respects safety, visual recovery and complications of both methods. Patients and Methods: One hundred Aphakic eyes were arbitrarily distributed between two groups. Group A included 50 eyes treated with retropupillary fixation of iris claw lens and group B included 50 eyes treated with Y-shaped intra-scleral fixation technique. Preoperative, intraoperative and postoperative data were analysed including best corrected visual acuity (BCVA), intraocular pressure (IOP), surgical time, intraoperative problems, IOL malposition and postoperative complications. Following up on patients was carried out for at least six months. Results: The mean duration of surgery was 21 ± 5.3 min in group A and was 53.4 ± 6.9 min in group B (p-value 0.05). IOL tilt was found in 0 (0%) eyes in group A and in 5 (10%) eyes in group B (p 0.05). Conclusion: The results of our study indicated that both methods are satisfactory in correcting aphakia without sufficient capsular support as regards postoperative best corrected visual acuity (BCVA);however the surgical technique of retropupillary iris claw lens is easier, shorter, with low intra- and postoperative complications and safer than those used for intra-scleral fixation of IOL. But for eyes which lack both iris and capsular support, a scleral fixation of a posterior chamber IOL remains the only option.

Comparison of lag screws and double Y-shaped miniplates in the fixation of anterior mandibular fractures

BACKGROUNDMandibular fractures constitute about 80.79% of maxillofacial injuries inAlexandria University, either as isolated mandibular fractures or as a part ofpanfacial fractures. The combination of symphyseal and parasymphyseal fracturesrepresent 47.09% of the total mandibular fractures.AIMTo compare the effectiveness of lag screws vs double Y-shaped miniplates in thefixation of anterior mandibular fractures.METHODSThis study is a prospective randomized controlled clinical trial, performed onsixteen patients with anterior mandibular fractures. Patients were divided equallyinto two groups, each consisting of eight patients. Group 1: Underwent openreduction and internal fixation using two lag screws. Group 2: Underwent openreduction and internal fixation using double Y-shaped plates. The followingparameters were assessed: operating time in minutes, pain using a visual analogscale, edema, surgical wound healing for signs and symptoms of infection,occlusion status and stability, maximal mouth opening, and sensory nervefunction. Cone beam computed tomography was performed at 3 and 6 mo tomeasure bone density and assess the progression of fracture healing.RESULTSThe study included 13 males (81.3%) and 3 females (18.8%) aged 26 to 45 years(mean age was 35.69 ± 6.01 years). The cause of trauma was road traffic accidentsin 10 patients (62.5%), interpersonal violence in 3 patients (18.8%) and othercauses in 3 patients (18.8%). The fractures comprised 10 parasymphyseal fractures(62.5%) and 6 symphyseal fractures (37.5%). The values of all parameters were comparable in both groups with no statistically significant difference except forthe mean bone density at 3 mo postoperatively which was 946.38 ± 66.29 in group 1 and 830.36 ± 95.53 in group 2 (P = 0.015).CONCLUSIONBoth lag screws and double Y-shaped miniplates provide favorable means offixation for mandibular fractures in the anterior region. Fractures fixed with lagscrews show greater mean bone density at 3 mo post-operation, indicative ofhigher primary stability and faster early bone healing. Further studies with largersample sizes are required to verify these conclusions.

Nondoped-type White Organic Light-Emitting Diode Using Star-Shaped Hexafluorenylbenzene as an Energy Transfer Layer

White organic light-emitting diodes （WOLEDs） with a structure of indium-tin-oxide （ITO）/N,N＇-bis- （1-naphthyl）-N,N＇-diphenyl- （1, 1＇-biphenyl）-4,4＇-diamine （NPB）/1,2,3,4,5,6-hexakis（9,9-diethyl-9H-fluoren-2- yl）benzene （HKEthFLYPh）/5,6,11,12-tetraphenylnaphtacene （rubrene）/tris（8-hydroxyquinoline） aluminum （Alq3）/Mg：Ag were fabricated by vacuum deposition method, in which a novel star-shaped hexafluorenyl- benzene HKEthFLYPh was used as an energy transfer layer, and an ultrathin layer of rubrene was inserted between HKEthFLYPh and Alq3 layers as a yellow light-emitting layer instead of using a time-consuming doping process. A fairly pure WOLED with Commissions Internationale De L＇Eclairage （CIE） coordinates of （0.32, 0.33） was obtained when the thickness of rubrene was 0.3 nm, and the spectrum was insensitive to the applied voltage. The device yielded a maximum luminance of 4816 cd/m2 at 18 V.