Hydrodynamics characterization in terms offlow regime behavior is a crucial task to enhance the design of bubble column reactors and scaling up related methodologies.This review presents recent studies on the typicalflo...Hydrodynamics characterization in terms offlow regime behavior is a crucial task to enhance the design of bubble column reactors and scaling up related methodologies.This review presents recent studies on the typicalflow regimes established in bubble columns.Some effort is also provided to introduce relevant definitions pertaining to thisfield,namely,that of“void fraction”and related(local,chordal,cross-sectional and volumetric)variants.Experimental studies involving different parameters that affect design and operating conditions are also discussed in detail.In the second part of the review,the attention is shifted to cases with internals of various types(perfo-rated plates,baffles,vibrating helical springs,mixers,and heat exchanger tubes)immersed in the bubble columns.It is shown that the presence of these elements has a limited influence on the global column hydrodynamics.However,they can make the homogeneousflow regime more stable in terms of transition gas velocity and transi-tion holdup value.The last section is used to highlight gaps which have not beenfilled yet and future directions of investigation.展开更多
The utilization of stone columns has emerged as a popular ground improvement strategy,whereas the drainage performance can be adversely hampered by clogging effect.Despite the ample progress of calculation methods for...The utilization of stone columns has emerged as a popular ground improvement strategy,whereas the drainage performance can be adversely hampered by clogging effect.Despite the ample progress of calculation methods for the consolidation of stone column-improved ground,theoretical investigations into the clogging effect have not been thoroughly explored.Furthermore,it is imperative to involve the column consolidation deformation to mitigate computational error on the consolidation of composite ground with high replacement ratios.In this context,an analytical model accounting for the initial clogging and coupled time and depth-dependent clogging of stone columns is established.Then,the resulting governing equations and analytical solutions are obtained under a new flow continuity relationship to incorporate column consolidation deformation.The accuracy and reliability of the proposed model are illustrated by degradation analysis and case studies with good agreements.Subsequently,the computed results of the current study are juxtaposed against the existing models,and an in-depth assessment of the impacts of several crucial parameters on the consolidation behavior is conducted.The results reveal that ignoring column consolidation deformation leads to an overestimate of the consolidation rate,with maximum error reaching up to 16%as the replacement ratio increases.Furthermore,the initial clogging also has a significant influence on the consolidation performance.Additionally,the increment of depth and time-clogging factors a and b will induce a noticeable retardation of the consolidation process,particularly in the later stage.展开更多
The addition of dispersed-phase nanoparticles in the liquid phase can enhance the gas-liquid transfer process as the suspended nanoparticles affect the transfer process inside the fluid through microdisturbance or mic...The addition of dispersed-phase nanoparticles in the liquid phase can enhance the gas-liquid transfer process as the suspended nanoparticles affect the transfer process inside the fluid through microdisturbance or micro-convection effects.In this article,a high-speed digital camera was used to visualize the bubble behavior of CO_(2) in pure water and nanofluids to examine the effects of CO_(2) gas flow rate,nanoparticle solid content and type on the bubble behavior in the fluids.The CO_(2) absorption performance in three water-based nanofluids were compared in a bubbler.And the mass transfer characteristics during CO_(2) bubble absorption and the reasons for the enhanced gas-liquid mass transfer effect of nanoparticles were analyzed.The results showed that the presence of nanoparticles affected the formation process of bubbles in the fluid,shortened the bubble detachment time,reduced the detachment diameter,effectively increased the gas-liquid contact area,and improved the bubbles detachment frequency.The system with MCM-41 corresponded to a higher overall mass transfer coefficient.Uncalined MCM-41 contained surfactant that enhanced foaming behavior in water.This prevented the transfer of CO_(2) to some extent,and the CO_(2) absorption by uncalined MCM-41/H_(2)O was 5.34%higher than that by pure water.Compared with SiO_(2) nanoparticles with the same particle size and the same composition,MCM-41 had a higher adsorption capacity and better hydrophilicity due to its larger specific surface area and rich porous structure,which was more favorable to accelerate the collision between nanoparticles and CO_(2) bubbles to cause micro-convection.Under the condition of 0.1%(mass)solid content,the enhancement of CO_(2) absorption process by MCM-41 nanoparticles was more significant and improved by 16.9%compared with pure water.展开更多
Pitting corrosion is harmful during bridge construction,which will lead to uneven roughness of steel surfaces and reduce the thickness of steel.Hence,the effect of pitting corrosion on the mechanical properties of col...Pitting corrosion is harmful during bridge construction,which will lead to uneven roughness of steel surfaces and reduce the thickness of steel.Hence,the effect of pitting corrosion on the mechanical properties of cold-formed thin-walled steel stub columns is studied,and the empirical formulas are established through regression fitting to predict the ultimate load of web and flange under pitting corrosion.In detail,the failure modes and load-displacement curves of specimens with different locations,area ratios,and depths are obtained through a large number of non-linear finite element analysis.As for the specimens with pitting corrosion on the web,all the specimens are subject to local buckling failure,and the failure mode will not change with pitting corrosion,but the failure location will change with pitting corrosion location;the size,location,and area ratio of pitting corrosion have little influence on the ultimate load of cold-formed thin-walled steel short columns,but the loss rate of pitting corrosion section area has a greater impact on the ultimate bearing capacity.As for the specimen with flange pitting corrosion,the location and area ratio of pitting corrosion have less influence on the ultimate load of cold-formed thin-walled steel short columns,and the section area loss rate has greater influence on the ultimate bearing capacity;the impact of web pitting corrosion on the ultimate load is greater than that of flange pitting corrosion under the same condition of pitting corrosion section area.The prediction formulas of limit load which are suitable for pitting corrosion of web and flange are established,which can provide a reference for performance evaluation of corroded cold-formed thin-walled steel.展开更多
This manuscript presents a dataset detailing a method for purifying monomers. Purification plays a crucial role in every chemical process, as it leads to an improvement in product quality through the removal of impuri...This manuscript presents a dataset detailing a method for purifying monomers. Purification plays a crucial role in every chemical process, as it leads to an improvement in product quality through the removal of impurities. The primary method for monomer purification, like acrylonitrile (AN), is the distillation technique. However, this technique is unsafe and hard to set up or handle. A straightforward, risk-free, low-cost method like the column technique resolves these issues. A simple column technique demonstrated the successful execution of purifying AN. Fourier transform infrared (FTIR) and nuclear magnetic resonance (NMR) analyses confirmed that AN was successfully purified, with purity reaching 99.8%. FTIR spectra revealed changes in the position and intensity of the stretching vibration peaks after purification. Also, the functional groups of the inhibitor monomethyl ether of hydroquinone (MeHQ) were undetected after purification. Furthermore, after purification, NMR spectra revealed the absence of aromatic protons and carbons associated with MeHQ. In conclusion, the column technique is a successful and inexpensive way to purify AN monomers. This makes it useful for a wide range of applications, especially in polymerization reactions where MeHQ needs to be removed to prevent self-polymerization during the initiation process.展开更多
A 67-year-old man had a sev-ere cough and pulmonary infection for 1 wk before seeking evaluation at our hospital.He had undergone esophagectomy with gastric pull-up and radiotherapy for esophageal cancer 3 years previ...A 67-year-old man had a sev-ere cough and pulmonary infection for 1 wk before seeking evaluation at our hospital.He had undergone esophagectomy with gastric pull-up and radiotherapy for esophageal cancer 3 years previously.After admission to our hospital,gastroscopy and bronchoscopy revealed a fistulous communication between the posterior tracheal wallnear the carina and the upper residual stomach.We measured the diameter of the trachea and bronchus and determined the site and size of the fistula using multislice computed tomography and gastroscopy.A covered self-expanding Y-shaped metallic stent was implanted into the trachea and bronchus.Subsequently,the fistula was closed completely.The patient tolerated the stent well and had good palliation of his symptoms.展开更多
Novel Y-shaped block copolymers of poly(ethylene glycol) and poly(N-isopropylacrylamide), PEG-b-(PNIPAM)2, were successfully synthesized through atom transfer radical polymerization (ATRP). A difunctional macr...Novel Y-shaped block copolymers of poly(ethylene glycol) and poly(N-isopropylacrylamide), PEG-b-(PNIPAM)2, were successfully synthesized through atom transfer radical polymerization (ATRP). A difunctional macroinitiator was prepared by esterification of 2,2-dichloroacetyl chloride with poly(ethylene glycol) monomethyl ether (PEG). The copolymers were obtained via the ATRP ofN-isopropylacrylamide (NIPAM) at 30℃ with CuCl/Me6TREN as a catalyst system and DMF/H2O (v/v = 3:1) mixture as solvent. The resulting copolymers were characterized by gel permeation chromatography (GPC) and ^1H NMR. These block copolymers show controllable molecular weights and narrow molecular weight distributions (PDI 〈 1.15). Their phase transition temperatures and the corresponding enthalpy changes in aqueous solution were measured by differential scanning calorimetry (DSC). As a result, the phase transition temperature of PEG45-b-(PNIPAM55)2 is higher than that of PNIPAM, however, the corresponding enthalpy change is much lower, indicating the significant influence of the macromolecular composition and architecture on the phase transition.展开更多
In this study,an optimization method is proposed to enhance the gas–liquid mass transfer in bubble column reactor based on the entropy generation extremum principle.The mass transfer–induced entropy generation can b...In this study,an optimization method is proposed to enhance the gas–liquid mass transfer in bubble column reactor based on the entropy generation extremum principle.The mass transfer–induced entropy generation can be maximized with the increase of mass transfer rate,based on which the velocity field can be optimized.The oxygen gas–liquid mass transfer is the major rate–limiting step of the toluene emissions biodegradation process in bubble column reactor,so the entropy generation due to oxygen mass transfer is used as the objective function,and the conservation equations of the gas–liquid flow and species concentration are taken as constraints.This optimization problem is solved by the calculus of variations,the optimal liquid flow pattern is obtained and the relationship of the maximum mass transfer enhancement on viscous dissipation is revealed,which can be used to improve the design of internal structure of the bubble column reactor.展开更多
We implement a binary collision approximation to study solitary wave propagation in a two-dimensional double Y- shaped granular chain. The solitary wave was transmitted and reflected when it met the interface of the b...We implement a binary collision approximation to study solitary wave propagation in a two-dimensional double Y- shaped granular chain. The solitary wave was transmitted and reflected when it met the interface of the bifurcated branches of the Y-shaped granular chains. We obtain the analytic results of the ratios of the transmitted and reflected speeds to the incident speed of the solitary wave, the maximum force between the two neighbor beads in a solitary wave, and the total time taken by the pulse to pass through each branch. All of the analytic results are in good agreement with the experimental observations from Daraio et al. [Phys. Rev. E 82 036603 (2010)]. Moreover, we also discuss the delay effects on the arrival of split pulses, and predict the recombination of the split waves traveling in branches in the final stem of asymmetric systems. The prediction of pulse recombination is verified by our numerical results.展开更多
As a traditional herbal medicine,the major alkaloids in Uncaria rhynchophylla have been proven to have blood pressure-lowering and sedative effects.It is essential to develop an effective method for the determination ...As a traditional herbal medicine,the major alkaloids in Uncaria rhynchophylla have been proven to have blood pressure-lowering and sedative effects.It is essential to develop an effective method for the determination of the major alkaloids in U.rhynchophylla.In this research,a rapid quantitative analysis involving multi-components analysis by a single marker strategy coupled with core-shell column HPLC was adopted to analyse four alkaloids(corynoxeine,isocorynoxeine,isorhynchophylline,rhynchophylline)in U.rhynchophylla.Isorhynchophylline was selected as the internal reference substance,the content of which was determined by the traditional external standard method.Relative correction factors(RCF)between isorhynchophylline and the other three alkaloids were calculated respectively.The results showed that the QAMS method had good robustness under different HPLC instruments.Nineteen batches of U.rhynchophylla were tested.No significant difference was observed between the results by QAMS and EMS(Correlation coefficient>0.99,p>0.05).The QAMS method could be employed as a rapid,effective technique for the quality control of U.rhynchophylla.展开更多
The selective aerobic oxidation of benzyl alcohol to benzaldehyde has attracted considerable attention because benzaldehyde is a high value-added product. The rate of this typical gas–liquid reaction is significantly...The selective aerobic oxidation of benzyl alcohol to benzaldehyde has attracted considerable attention because benzaldehyde is a high value-added product. The rate of this typical gas–liquid reaction is significantly affected by mass transfer. In this study, CoTPP-mediated(CoTPP: cobalt(II) mesotetraphenylporphyrin) selective benzyl alcohol oxidation with oxygen was conducted in a membrane microchannel(MMC) reactor and a bubble column(BC) reactor, respectively. We observed that 83% benzyl alcohol was converted within 6.5 min in the MMC reactor, but only less than 10% benzyl alcohol was converted in the BC reactor. Hydrodynamic characteristics and gas–liquid mass transfer performances were compared for the MMC and BC reactors. The MMC reactor was assumed to be a plug flow reactor,and the dimensionless variance was 0.29. Compared to the BC reactor, the gas–liquid mass transfer was intensified significantly in MMC reactor. It could be ascribed to the high gas holdup(2.9 times higher than that of BC reactor), liquid film mass transfer coefficient(8.2 times higher than that of BC reactor), and mass transfer coefficient per unit interfacial area(3.8 times higher than that of BC reactor). Moreover,the Hatta number for the MMC reactor reached up to 0.61, which was about 15 times higher than that of the BC reactor. The computational fluid dynamics calculations for mass fractions in both liquid and gas phases were consistent with the experimental data.展开更多
Based on Mindlin stress solution, a numerical computational method was proposed to calculate the stresses in the ground induced by side friction and the resistance of Y-shaped vibro-pile. The improved Terzaghi's a...Based on Mindlin stress solution, a numerical computational method was proposed to calculate the stresses in the ground induced by side friction and the resistance of Y-shaped vibro-pile. The improved Terzaghi's and ЪерезанцевВГ's methods for ultimate bearing capacity evaluation were proposed by considering the stress strength induced by friction resistance at pile head level of Y-pile. A new method to calculate the ultimate bearing capacity of Y-pile was also proposed based on the assumptions of soil failure mode at the tip of Y-pile and the use of Mohr-Coulomb soil yield criterion and Vesic compressive correction coefficient with the induced stresses in the ground. Based on the comparisons with the field static load test results, it is found that the improved Terzaghi's method gives higher ultimate capacity, while the other two methods shows good agreement with the field results.展开更多
To implement the performance-based seismic design of engineered structures,the failure modes of members must be classified.The classification method of column failure modes is analyzed using data from the Pacific Eart...To implement the performance-based seismic design of engineered structures,the failure modes of members must be classified.The classification method of column failure modes is analyzed using data from the Pacific Earthquake Engineering Research Center(PEER).The main factors affecting failure modes of columns include the hoop ratios,longitudinal reinforcement ratios,ratios of transverse reinforcement spacing to section depth,aspect ratios,axial compression ratios,and flexure-shear ratios.This study proposes a data-driven prediction model based on an artificial neural network(ANN)to identify the column failure modes.In this study,111 groups of data are used,out of which 89 are used as training data and 22 are used as test data,and the ANN prediction model of failure modes is developed.The results show that the proposed method based on ANN is superior to traditional methods in identifying the column failure modes.展开更多
The transports of the dynamic biochemical signals in the non-reversing pulsatile flows in the mixing microchannel of a Y-shaped microfluidic device are ana- lyzed. The results show that the mixing micro-channel acts a...The transports of the dynamic biochemical signals in the non-reversing pulsatile flows in the mixing microchannel of a Y-shaped microfluidic device are ana- lyzed. The results show that the mixing micro-channel acts as a low-pass filter, and the biochemical signals are nonlinearly modulated by the pulsatile flows, which depend on the biochemical signal frequency, the flow signal frequency, and the biochemical signal transporting distance. It is concluded that, the transfer characteristics of the dynamic biochemical signals, which are transported in the time-varying flows, should be carefully considered for better loading biochemical signals on the cells cultured on the bottom of the microfluidic channel.展开更多
Background: Many reasons can lead to an aphakia without adequate capsular support for implantation of a posterior chamber intraocular lens (IOL), such as intraoperative unintentional rupture of posterior capsule durin...Background: Many reasons can lead to an aphakia without adequate capsular support for implantation of a posterior chamber intraocular lens (IOL), such as intraoperative unintentional rupture of posterior capsule during phacoemulsification, planned intracapsular cataract extraction, ocular trauma and lens dislocation due to congenital and acquired causes. Purpose: To compare Y-shaped intra-scleral fixation of a posterior chamber IOL with retro pupillary fixation of an iris-claw intraocular lens (IOL) for Aphakic eyes without sufficient capsular support as respects safety, visual recovery and complications of both methods. Patients and Methods: One hundred Aphakic eyes were arbitrarily distributed between two groups. Group A included 50 eyes treated with retropupillary fixation of iris claw lens and group B included 50 eyes treated with Y-shaped intra-scleral fixation technique. Preoperative, intraoperative and postoperative data were analysed including best corrected visual acuity (BCVA), intraocular pressure (IOP), surgical time, intraoperative problems, IOL malposition and postoperative complications. Following up on patients was carried out for at least six months. Results: The mean duration of surgery was 21 ± 5.3 min in group A and was 53.4 ± 6.9 min in group B (p-value 0.05). IOL tilt was found in 0 (0%) eyes in group A and in 5 (10%) eyes in group B (p 0.05). Conclusion: The results of our study indicated that both methods are satisfactory in correcting aphakia without sufficient capsular support as regards postoperative best corrected visual acuity (BCVA);however the surgical technique of retropupillary iris claw lens is easier, shorter, with low intra- and postoperative complications and safer than those used for intra-scleral fixation of IOL. But for eyes which lack both iris and capsular support, a scleral fixation of a posterior chamber IOL remains the only option.展开更多
BACKGROUNDMandibular fractures constitute about 80.79% of maxillofacial injuries inAlexandria University, either as isolated mandibular fractures or as a part ofpanfacial fractures. The combination of symphyseal and p...BACKGROUNDMandibular fractures constitute about 80.79% of maxillofacial injuries inAlexandria University, either as isolated mandibular fractures or as a part ofpanfacial fractures. The combination of symphyseal and parasymphyseal fracturesrepresent 47.09% of the total mandibular fractures.AIMTo compare the effectiveness of lag screws vs double Y-shaped miniplates in thefixation of anterior mandibular fractures.METHODSThis study is a prospective randomized controlled clinical trial, performed onsixteen patients with anterior mandibular fractures. Patients were divided equallyinto two groups, each consisting of eight patients. Group 1: Underwent openreduction and internal fixation using two lag screws. Group 2: Underwent openreduction and internal fixation using double Y-shaped plates. The followingparameters were assessed: operating time in minutes, pain using a visual analogscale, edema, surgical wound healing for signs and symptoms of infection,occlusion status and stability, maximal mouth opening, and sensory nervefunction. Cone beam computed tomography was performed at 3 and 6 mo tomeasure bone density and assess the progression of fracture healing.RESULTSThe study included 13 males (81.3%) and 3 females (18.8%) aged 26 to 45 years(mean age was 35.69 ± 6.01 years). The cause of trauma was road traffic accidentsin 10 patients (62.5%), interpersonal violence in 3 patients (18.8%) and othercauses in 3 patients (18.8%). The fractures comprised 10 parasymphyseal fractures(62.5%) and 6 symphyseal fractures (37.5%). The values of all parameters were comparable in both groups with no statistically significant difference except forthe mean bone density at 3 mo postoperatively which was 946.38 ± 66.29 in group 1 and 830.36 ± 95.53 in group 2 (P = 0.015).CONCLUSIONBoth lag screws and double Y-shaped miniplates provide favorable means offixation for mandibular fractures in the anterior region. Fractures fixed with lagscrews show greater mean bone density at 3 mo post-operation, indicative ofhigher primary stability and faster early bone healing. Further studies with largersample sizes are required to verify these conclusions.展开更多
In this paper,an improved computational fluid dynamic(CFD)model for gas-liquid flow in bubble column was developed using the one-equation Wary-Agarwal(WA)turbulence model coupled with the population balance model(PBM)...In this paper,an improved computational fluid dynamic(CFD)model for gas-liquid flow in bubble column was developed using the one-equation Wary-Agarwal(WA)turbulence model coupled with the population balance model(PBM).Through 18 orthogonal test cases,the optimal combination of interfacial force models,including drag force,lift force,turbulent dispersion force.The modified wall lubrication force model was proposed to improve the predictive ability for hydrodynamic behavior near the wall of the bubble column.The values simulated by optimized CFD model were in agreement with experimental data,and the errors were within±20%.In addition,the axial velocity,turbulent kinetic energy,bubble size distribution,and the dynamic characteristic of bubble plume were analyzed at different superficial gas velocities.This research work could provide a theoretical basis for the extension of the CFD-PBM coupled model to other multiphase reactors..展开更多
Packed columns are widely used in the chemical industry such as absorption,stripping,distillation,and extraction in the production of e.g.organic chemicals,and pharmaceuticals.Pressure loss and pressure drop correlati...Packed columns are widely used in the chemical industry such as absorption,stripping,distillation,and extraction in the production of e.g.organic chemicals,and pharmaceuticals.Pressure loss and pressure drop correlations are of special interest when it comes to the hydrodynamic properties of a column.The pressure loss across the column is of interest in the design phase when the size of the blower to drive the gas stream through the column has to be decided.The loading point and flooding point are also influenced by the pressure loss and the area of operation is determined from these points.This work examines four different correlations on pressure drop.The correlations are(i)Ergun’s equation(1952),(ii)an improved version of Ergun’s equation by Stichlmair,Bravo,and Fair(1989),(iii)an equation developed by Billet and Schultes(1999),and(iv)an equation by Rocha,Bravo,and Fair(1993).The complexity of the correlations is increasing in the mentioned order,Ergun’s equation being the simplest one.This study investigates if the more complicated correlations give better predictions to pressure drop in packed columns.This is determined by comparing the correlations to experimental data for pressure drop in a packed column with 8.2 m of structured packing using water as the liquid and atmospheric air as the gas.Seven experiments were carried out for determining the pressure drop in the column with liquid flows varying from 0 to 500 kg·h^(-1).At constant liquid flow,the gas flow was varied from approximately 10 to 70 kg·h^(-1).The pressure drop across the non-wetted column was best described by the correlation by Rocha et al.while the pressure drop for liquid flows from 100 to 500 kg·h^(-1)was,in general,best described by Stichlmair’s equation.For an irrigated column,the highest deviation was a predicted pressure drop 69.6%lower than measured.The best prediction was 0.1%higher than the measured.This study shows,surprisingly,that for a system of water and atmospheric air,complicated correlations on pressure drop determination do not provide better estimates than simple equations.展开更多
Cold seeps are widely developed on the seabed of continental margins and can form gas plumes due to the upward migration of methane-rich fluids.The detection and automatic segmentation of gas plumes are of great signi...Cold seeps are widely developed on the seabed of continental margins and can form gas plumes due to the upward migration of methane-rich fluids.The detection and automatic segmentation of gas plumes are of great significance in locating and studying the cold seep system that is usually accompanied by hydrate layers in the subsurface.A multibeam echo-sounder system(MBES)can record the complete backscatter intensity of the water column,and it is one of the most effective means for detecting cold seeps.However,the gas plumes recorded in multibeam water column images(WCI)are usually blurred due to the interference of the complicated water environment and the sidelobes of the MBES,making it difficult to obtain the effective segmentation.Therefore,based on the existing UNet semantic segmentation network,this paper proposes an AP-UNet network combining the convolutional block attention module and the pyramid pooling module for the automatic segmentation and extraction of gas plumes.Comparative experiments are conducted among three traditional segmentation methods and two deep learning methods.The results show that the AP-UNet segmentation model can effectively suppress complicated water column noise interference.The segmentation precision,the Dice coefficient,and the recall rate of this model are 92.09%,92.00%,and 92.49%,respectively,which are 1.17%,2.10%,and 2.07%higher than the results of the UNet.展开更多
文摘Hydrodynamics characterization in terms offlow regime behavior is a crucial task to enhance the design of bubble column reactors and scaling up related methodologies.This review presents recent studies on the typicalflow regimes established in bubble columns.Some effort is also provided to introduce relevant definitions pertaining to thisfield,namely,that of“void fraction”and related(local,chordal,cross-sectional and volumetric)variants.Experimental studies involving different parameters that affect design and operating conditions are also discussed in detail.In the second part of the review,the attention is shifted to cases with internals of various types(perfo-rated plates,baffles,vibrating helical springs,mixers,and heat exchanger tubes)immersed in the bubble columns.It is shown that the presence of these elements has a limited influence on the global column hydrodynamics.However,they can make the homogeneousflow regime more stable in terms of transition gas velocity and transi-tion holdup value.The last section is used to highlight gaps which have not beenfilled yet and future directions of investigation.
基金funding support from the National Natural Science Foundation of China(Grant Nos.52178373 and 51878657).
文摘The utilization of stone columns has emerged as a popular ground improvement strategy,whereas the drainage performance can be adversely hampered by clogging effect.Despite the ample progress of calculation methods for the consolidation of stone column-improved ground,theoretical investigations into the clogging effect have not been thoroughly explored.Furthermore,it is imperative to involve the column consolidation deformation to mitigate computational error on the consolidation of composite ground with high replacement ratios.In this context,an analytical model accounting for the initial clogging and coupled time and depth-dependent clogging of stone columns is established.Then,the resulting governing equations and analytical solutions are obtained under a new flow continuity relationship to incorporate column consolidation deformation.The accuracy and reliability of the proposed model are illustrated by degradation analysis and case studies with good agreements.Subsequently,the computed results of the current study are juxtaposed against the existing models,and an in-depth assessment of the impacts of several crucial parameters on the consolidation behavior is conducted.The results reveal that ignoring column consolidation deformation leads to an overestimate of the consolidation rate,with maximum error reaching up to 16%as the replacement ratio increases.Furthermore,the initial clogging also has a significant influence on the consolidation performance.Additionally,the increment of depth and time-clogging factors a and b will induce a noticeable retardation of the consolidation process,particularly in the later stage.
基金financial support from National Natural Science Foundation of China(22108263)Shanxi Province Basic Research Program Project(20210302124060)the 18th Graduate Student Technology Project of North University of China(20221824).
文摘The addition of dispersed-phase nanoparticles in the liquid phase can enhance the gas-liquid transfer process as the suspended nanoparticles affect the transfer process inside the fluid through microdisturbance or micro-convection effects.In this article,a high-speed digital camera was used to visualize the bubble behavior of CO_(2) in pure water and nanofluids to examine the effects of CO_(2) gas flow rate,nanoparticle solid content and type on the bubble behavior in the fluids.The CO_(2) absorption performance in three water-based nanofluids were compared in a bubbler.And the mass transfer characteristics during CO_(2) bubble absorption and the reasons for the enhanced gas-liquid mass transfer effect of nanoparticles were analyzed.The results showed that the presence of nanoparticles affected the formation process of bubbles in the fluid,shortened the bubble detachment time,reduced the detachment diameter,effectively increased the gas-liquid contact area,and improved the bubbles detachment frequency.The system with MCM-41 corresponded to a higher overall mass transfer coefficient.Uncalined MCM-41 contained surfactant that enhanced foaming behavior in water.This prevented the transfer of CO_(2) to some extent,and the CO_(2) absorption by uncalined MCM-41/H_(2)O was 5.34%higher than that by pure water.Compared with SiO_(2) nanoparticles with the same particle size and the same composition,MCM-41 had a higher adsorption capacity and better hydrophilicity due to its larger specific surface area and rich porous structure,which was more favorable to accelerate the collision between nanoparticles and CO_(2) bubbles to cause micro-convection.Under the condition of 0.1%(mass)solid content,the enhancement of CO_(2) absorption process by MCM-41 nanoparticles was more significant and improved by 16.9%compared with pure water.
基金funded by the‘Research Project of the Sucheng to Sihong Section of the Yanluo Expressway-Measurement Technology and Application of Bridge Quality Project Based on UAV Binocular Imaging(No.00-00-JSFW-20230203-029)’,received by H.Z.Wang.
文摘Pitting corrosion is harmful during bridge construction,which will lead to uneven roughness of steel surfaces and reduce the thickness of steel.Hence,the effect of pitting corrosion on the mechanical properties of cold-formed thin-walled steel stub columns is studied,and the empirical formulas are established through regression fitting to predict the ultimate load of web and flange under pitting corrosion.In detail,the failure modes and load-displacement curves of specimens with different locations,area ratios,and depths are obtained through a large number of non-linear finite element analysis.As for the specimens with pitting corrosion on the web,all the specimens are subject to local buckling failure,and the failure mode will not change with pitting corrosion,but the failure location will change with pitting corrosion location;the size,location,and area ratio of pitting corrosion have little influence on the ultimate load of cold-formed thin-walled steel short columns,but the loss rate of pitting corrosion section area has a greater impact on the ultimate bearing capacity.As for the specimen with flange pitting corrosion,the location and area ratio of pitting corrosion have less influence on the ultimate load of cold-formed thin-walled steel short columns,and the section area loss rate has greater influence on the ultimate bearing capacity;the impact of web pitting corrosion on the ultimate load is greater than that of flange pitting corrosion under the same condition of pitting corrosion section area.The prediction formulas of limit load which are suitable for pitting corrosion of web and flange are established,which can provide a reference for performance evaluation of corroded cold-formed thin-walled steel.
文摘This manuscript presents a dataset detailing a method for purifying monomers. Purification plays a crucial role in every chemical process, as it leads to an improvement in product quality through the removal of impurities. The primary method for monomer purification, like acrylonitrile (AN), is the distillation technique. However, this technique is unsafe and hard to set up or handle. A straightforward, risk-free, low-cost method like the column technique resolves these issues. A simple column technique demonstrated the successful execution of purifying AN. Fourier transform infrared (FTIR) and nuclear magnetic resonance (NMR) analyses confirmed that AN was successfully purified, with purity reaching 99.8%. FTIR spectra revealed changes in the position and intensity of the stretching vibration peaks after purification. Also, the functional groups of the inhibitor monomethyl ether of hydroquinone (MeHQ) were undetected after purification. Furthermore, after purification, NMR spectra revealed the absence of aromatic protons and carbons associated with MeHQ. In conclusion, the column technique is a successful and inexpensive way to purify AN monomers. This makes it useful for a wide range of applications, especially in polymerization reactions where MeHQ needs to be removed to prevent self-polymerization during the initiation process.
文摘A 67-year-old man had a sev-ere cough and pulmonary infection for 1 wk before seeking evaluation at our hospital.He had undergone esophagectomy with gastric pull-up and radiotherapy for esophageal cancer 3 years previously.After admission to our hospital,gastroscopy and bronchoscopy revealed a fistulous communication between the posterior tracheal wallnear the carina and the upper residual stomach.We measured the diameter of the trachea and bronchus and determined the site and size of the fistula using multislice computed tomography and gastroscopy.A covered self-expanding Y-shaped metallic stent was implanted into the trachea and bronchus.Subsequently,the fistula was closed completely.The patient tolerated the stent well and had good palliation of his symptoms.
基金support from the National Natural Science Foundation of China(No. 20134020)the Visiting Scholar Project of Shandong Province of China(No.20081001)the Science Research Fund of Shandong Jiaotong University of China(No.Z200802)
文摘Novel Y-shaped block copolymers of poly(ethylene glycol) and poly(N-isopropylacrylamide), PEG-b-(PNIPAM)2, were successfully synthesized through atom transfer radical polymerization (ATRP). A difunctional macroinitiator was prepared by esterification of 2,2-dichloroacetyl chloride with poly(ethylene glycol) monomethyl ether (PEG). The copolymers were obtained via the ATRP ofN-isopropylacrylamide (NIPAM) at 30℃ with CuCl/Me6TREN as a catalyst system and DMF/H2O (v/v = 3:1) mixture as solvent. The resulting copolymers were characterized by gel permeation chromatography (GPC) and ^1H NMR. These block copolymers show controllable molecular weights and narrow molecular weight distributions (PDI 〈 1.15). Their phase transition temperatures and the corresponding enthalpy changes in aqueous solution were measured by differential scanning calorimetry (DSC). As a result, the phase transition temperature of PEG45-b-(PNIPAM55)2 is higher than that of PNIPAM, however, the corresponding enthalpy change is much lower, indicating the significant influence of the macromolecular composition and architecture on the phase transition.
基金supported by the National Natural Science Foundation of China(91834303 and 22108261)the Open Foundation of State Key Laboratory of Chemical Engineering(SKL-ChE-19B02)+1 种基金Fundamental Research Program of Shanxi Province(20210302124618)Scientific Technological Innovation Programs of Higher Education Institution in Shanxi(2020L0284).
文摘In this study,an optimization method is proposed to enhance the gas–liquid mass transfer in bubble column reactor based on the entropy generation extremum principle.The mass transfer–induced entropy generation can be maximized with the increase of mass transfer rate,based on which the velocity field can be optimized.The oxygen gas–liquid mass transfer is the major rate–limiting step of the toluene emissions biodegradation process in bubble column reactor,so the entropy generation due to oxygen mass transfer is used as the objective function,and the conservation equations of the gas–liquid flow and species concentration are taken as constraints.This optimization problem is solved by the calculus of variations,the optimal liquid flow pattern is obtained and the relationship of the maximum mass transfer enhancement on viscous dissipation is revealed,which can be used to improve the design of internal structure of the bubble column reactor.
基金Project supported by the Science Fund for Creative Research Groups of the National Natural Science Foundation of China (Grant No. 50921002)the Fundamental Research Funds for the Central Universities of China (Grant No. 2010LKWL09)
文摘We implement a binary collision approximation to study solitary wave propagation in a two-dimensional double Y- shaped granular chain. The solitary wave was transmitted and reflected when it met the interface of the bifurcated branches of the Y-shaped granular chains. We obtain the analytic results of the ratios of the transmitted and reflected speeds to the incident speed of the solitary wave, the maximum force between the two neighbor beads in a solitary wave, and the total time taken by the pulse to pass through each branch. All of the analytic results are in good agreement with the experimental observations from Daraio et al. [Phys. Rev. E 82 036603 (2010)]. Moreover, we also discuss the delay effects on the arrival of split pulses, and predict the recombination of the split waves traveling in branches in the final stem of asymmetric systems. The prediction of pulse recombination is verified by our numerical results.
文摘As a traditional herbal medicine,the major alkaloids in Uncaria rhynchophylla have been proven to have blood pressure-lowering and sedative effects.It is essential to develop an effective method for the determination of the major alkaloids in U.rhynchophylla.In this research,a rapid quantitative analysis involving multi-components analysis by a single marker strategy coupled with core-shell column HPLC was adopted to analyse four alkaloids(corynoxeine,isocorynoxeine,isorhynchophylline,rhynchophylline)in U.rhynchophylla.Isorhynchophylline was selected as the internal reference substance,the content of which was determined by the traditional external standard method.Relative correction factors(RCF)between isorhynchophylline and the other three alkaloids were calculated respectively.The results showed that the QAMS method had good robustness under different HPLC instruments.Nineteen batches of U.rhynchophylla were tested.No significant difference was observed between the results by QAMS and EMS(Correlation coefficient>0.99,p>0.05).The QAMS method could be employed as a rapid,effective technique for the quality control of U.rhynchophylla.
基金financially supported by the National Key Research and Development Program of China (2020YFA0210900)the National Natural Science Foundation of China (21938001 and 21878344)+1 种基金Guangdong Provincial Key Research and Development Programme (2019B110206002)the Local Innovative and Research Teams Project of Guangdong Pearl River Talents Program (2017BT01C102)。
文摘The selective aerobic oxidation of benzyl alcohol to benzaldehyde has attracted considerable attention because benzaldehyde is a high value-added product. The rate of this typical gas–liquid reaction is significantly affected by mass transfer. In this study, CoTPP-mediated(CoTPP: cobalt(II) mesotetraphenylporphyrin) selective benzyl alcohol oxidation with oxygen was conducted in a membrane microchannel(MMC) reactor and a bubble column(BC) reactor, respectively. We observed that 83% benzyl alcohol was converted within 6.5 min in the MMC reactor, but only less than 10% benzyl alcohol was converted in the BC reactor. Hydrodynamic characteristics and gas–liquid mass transfer performances were compared for the MMC and BC reactors. The MMC reactor was assumed to be a plug flow reactor,and the dimensionless variance was 0.29. Compared to the BC reactor, the gas–liquid mass transfer was intensified significantly in MMC reactor. It could be ascribed to the high gas holdup(2.9 times higher than that of BC reactor), liquid film mass transfer coefficient(8.2 times higher than that of BC reactor), and mass transfer coefficient per unit interfacial area(3.8 times higher than that of BC reactor). Moreover,the Hatta number for the MMC reactor reached up to 0.61, which was about 15 times higher than that of the BC reactor. The computational fluid dynamics calculations for mass fractions in both liquid and gas phases were consistent with the experimental data.
文摘Based on Mindlin stress solution, a numerical computational method was proposed to calculate the stresses in the ground induced by side friction and the resistance of Y-shaped vibro-pile. The improved Terzaghi's and ЪерезанцевВГ's methods for ultimate bearing capacity evaluation were proposed by considering the stress strength induced by friction resistance at pile head level of Y-pile. A new method to calculate the ultimate bearing capacity of Y-pile was also proposed based on the assumptions of soil failure mode at the tip of Y-pile and the use of Mohr-Coulomb soil yield criterion and Vesic compressive correction coefficient with the induced stresses in the ground. Based on the comparisons with the field static load test results, it is found that the improved Terzaghi's method gives higher ultimate capacity, while the other two methods shows good agreement with the field results.
基金China Energy Engineering Group Planning&Engineering Co.,Ltd.Concentrated Development Scientific Research Project Under Grant No.GSKJ2-T11-2019。
文摘To implement the performance-based seismic design of engineered structures,the failure modes of members must be classified.The classification method of column failure modes is analyzed using data from the Pacific Earthquake Engineering Research Center(PEER).The main factors affecting failure modes of columns include the hoop ratios,longitudinal reinforcement ratios,ratios of transverse reinforcement spacing to section depth,aspect ratios,axial compression ratios,and flexure-shear ratios.This study proposes a data-driven prediction model based on an artificial neural network(ANN)to identify the column failure modes.In this study,111 groups of data are used,out of which 89 are used as training data and 22 are used as test data,and the ANN prediction model of failure modes is developed.The results show that the proposed method based on ANN is superior to traditional methods in identifying the column failure modes.
基金Project supported by the National Natural Science Foundation of China(Nos.11172060 and11672065)
文摘The transports of the dynamic biochemical signals in the non-reversing pulsatile flows in the mixing microchannel of a Y-shaped microfluidic device are ana- lyzed. The results show that the mixing micro-channel acts as a low-pass filter, and the biochemical signals are nonlinearly modulated by the pulsatile flows, which depend on the biochemical signal frequency, the flow signal frequency, and the biochemical signal transporting distance. It is concluded that, the transfer characteristics of the dynamic biochemical signals, which are transported in the time-varying flows, should be carefully considered for better loading biochemical signals on the cells cultured on the bottom of the microfluidic channel.
文摘Background: Many reasons can lead to an aphakia without adequate capsular support for implantation of a posterior chamber intraocular lens (IOL), such as intraoperative unintentional rupture of posterior capsule during phacoemulsification, planned intracapsular cataract extraction, ocular trauma and lens dislocation due to congenital and acquired causes. Purpose: To compare Y-shaped intra-scleral fixation of a posterior chamber IOL with retro pupillary fixation of an iris-claw intraocular lens (IOL) for Aphakic eyes without sufficient capsular support as respects safety, visual recovery and complications of both methods. Patients and Methods: One hundred Aphakic eyes were arbitrarily distributed between two groups. Group A included 50 eyes treated with retropupillary fixation of iris claw lens and group B included 50 eyes treated with Y-shaped intra-scleral fixation technique. Preoperative, intraoperative and postoperative data were analysed including best corrected visual acuity (BCVA), intraocular pressure (IOP), surgical time, intraoperative problems, IOL malposition and postoperative complications. Following up on patients was carried out for at least six months. Results: The mean duration of surgery was 21 ± 5.3 min in group A and was 53.4 ± 6.9 min in group B (p-value 0.05). IOL tilt was found in 0 (0%) eyes in group A and in 5 (10%) eyes in group B (p 0.05). Conclusion: The results of our study indicated that both methods are satisfactory in correcting aphakia without sufficient capsular support as regards postoperative best corrected visual acuity (BCVA);however the surgical technique of retropupillary iris claw lens is easier, shorter, with low intra- and postoperative complications and safer than those used for intra-scleral fixation of IOL. But for eyes which lack both iris and capsular support, a scleral fixation of a posterior chamber IOL remains the only option.
文摘BACKGROUNDMandibular fractures constitute about 80.79% of maxillofacial injuries inAlexandria University, either as isolated mandibular fractures or as a part ofpanfacial fractures. The combination of symphyseal and parasymphyseal fracturesrepresent 47.09% of the total mandibular fractures.AIMTo compare the effectiveness of lag screws vs double Y-shaped miniplates in thefixation of anterior mandibular fractures.METHODSThis study is a prospective randomized controlled clinical trial, performed onsixteen patients with anterior mandibular fractures. Patients were divided equallyinto two groups, each consisting of eight patients. Group 1: Underwent openreduction and internal fixation using two lag screws. Group 2: Underwent openreduction and internal fixation using double Y-shaped plates. The followingparameters were assessed: operating time in minutes, pain using a visual analogscale, edema, surgical wound healing for signs and symptoms of infection,occlusion status and stability, maximal mouth opening, and sensory nervefunction. Cone beam computed tomography was performed at 3 and 6 mo tomeasure bone density and assess the progression of fracture healing.RESULTSThe study included 13 males (81.3%) and 3 females (18.8%) aged 26 to 45 years(mean age was 35.69 ± 6.01 years). The cause of trauma was road traffic accidentsin 10 patients (62.5%), interpersonal violence in 3 patients (18.8%) and othercauses in 3 patients (18.8%). The fractures comprised 10 parasymphyseal fractures(62.5%) and 6 symphyseal fractures (37.5%). The values of all parameters were comparable in both groups with no statistically significant difference except forthe mean bone density at 3 mo postoperatively which was 946.38 ± 66.29 in group 1 and 830.36 ± 95.53 in group 2 (P = 0.015).CONCLUSIONBoth lag screws and double Y-shaped miniplates provide favorable means offixation for mandibular fractures in the anterior region. Fractures fixed with lagscrews show greater mean bone density at 3 mo post-operation, indicative ofhigher primary stability and faster early bone healing. Further studies with largersample sizes are required to verify these conclusions.
基金supported by the National Natural Science Foundation of China(22078009)National Key Research and Development Program of China(2021YFC3001102,2021YFC3001100)。
文摘In this paper,an improved computational fluid dynamic(CFD)model for gas-liquid flow in bubble column was developed using the one-equation Wary-Agarwal(WA)turbulence model coupled with the population balance model(PBM).Through 18 orthogonal test cases,the optimal combination of interfacial force models,including drag force,lift force,turbulent dispersion force.The modified wall lubrication force model was proposed to improve the predictive ability for hydrodynamic behavior near the wall of the bubble column.The values simulated by optimized CFD model were in agreement with experimental data,and the errors were within±20%.In addition,the axial velocity,turbulent kinetic energy,bubble size distribution,and the dynamic characteristic of bubble plume were analyzed at different superficial gas velocities.This research work could provide a theoretical basis for the extension of the CFD-PBM coupled model to other multiphase reactors..
基金the BioCO_(2) project(the Danish government through the EUDP agency No.64016-0082)the INTERACT project(European Union Seventh Framework Programme FP7/2007-2013 under grant agreement No.608535)the financial support from the Center for Energy Resources Engineering(CERE),and the Technical University of Denmark.
文摘Packed columns are widely used in the chemical industry such as absorption,stripping,distillation,and extraction in the production of e.g.organic chemicals,and pharmaceuticals.Pressure loss and pressure drop correlations are of special interest when it comes to the hydrodynamic properties of a column.The pressure loss across the column is of interest in the design phase when the size of the blower to drive the gas stream through the column has to be decided.The loading point and flooding point are also influenced by the pressure loss and the area of operation is determined from these points.This work examines four different correlations on pressure drop.The correlations are(i)Ergun’s equation(1952),(ii)an improved version of Ergun’s equation by Stichlmair,Bravo,and Fair(1989),(iii)an equation developed by Billet and Schultes(1999),and(iv)an equation by Rocha,Bravo,and Fair(1993).The complexity of the correlations is increasing in the mentioned order,Ergun’s equation being the simplest one.This study investigates if the more complicated correlations give better predictions to pressure drop in packed columns.This is determined by comparing the correlations to experimental data for pressure drop in a packed column with 8.2 m of structured packing using water as the liquid and atmospheric air as the gas.Seven experiments were carried out for determining the pressure drop in the column with liquid flows varying from 0 to 500 kg·h^(-1).At constant liquid flow,the gas flow was varied from approximately 10 to 70 kg·h^(-1).The pressure drop across the non-wetted column was best described by the correlation by Rocha et al.while the pressure drop for liquid flows from 100 to 500 kg·h^(-1)was,in general,best described by Stichlmair’s equation.For an irrigated column,the highest deviation was a predicted pressure drop 69.6%lower than measured.The best prediction was 0.1%higher than the measured.This study shows,surprisingly,that for a system of water and atmospheric air,complicated correlations on pressure drop determination do not provide better estimates than simple equations.
基金Supported by the National Natural Science Foundation of China (Nos.41930535,41906165)the High-level Foreign Expert Introduction Program (No.G2021025006L)the SDUST Research Fund (No.2019TDJH103)。
文摘Cold seeps are widely developed on the seabed of continental margins and can form gas plumes due to the upward migration of methane-rich fluids.The detection and automatic segmentation of gas plumes are of great significance in locating and studying the cold seep system that is usually accompanied by hydrate layers in the subsurface.A multibeam echo-sounder system(MBES)can record the complete backscatter intensity of the water column,and it is one of the most effective means for detecting cold seeps.However,the gas plumes recorded in multibeam water column images(WCI)are usually blurred due to the interference of the complicated water environment and the sidelobes of the MBES,making it difficult to obtain the effective segmentation.Therefore,based on the existing UNet semantic segmentation network,this paper proposes an AP-UNet network combining the convolutional block attention module and the pyramid pooling module for the automatic segmentation and extraction of gas plumes.Comparative experiments are conducted among three traditional segmentation methods and two deep learning methods.The results show that the AP-UNet segmentation model can effectively suppress complicated water column noise interference.The segmentation precision,the Dice coefficient,and the recall rate of this model are 92.09%,92.00%,and 92.49%,respectively,which are 1.17%,2.10%,and 2.07%higher than the results of the UNet.