In this paper,a 5G wideband power amplifier(PA)with bandpass filtering response is synthesized using a bandwidth-extended bandpass filter as the matching network(MN).In this structure,the bandwidth(θ_(C))is defined a...In this paper,a 5G wideband power amplifier(PA)with bandpass filtering response is synthesized using a bandwidth-extended bandpass filter as the matching network(MN).In this structure,the bandwidth(θ_(C))is defined as a variable in the closedform equations provided by the microstrip bandpass filter.It can be extended over a wide range only by changing the characteristic impedances of the structure.Different from the other wideband MNs,the extension of bandwidth does not increase the complexity of the structure(order n is fixed).In addition,based on the bandwidth-extended structure,the wideband design of bandpass filtering PA is not limited to the fixed bandwidth of the specific filter structure.The theoretical analysis of the MN and the design flow of the PA are provided in this design.The fabricated bandpass filtering PA can support almost one-octave bandwidth(2-3.8 GHz),covering the two 5G bands(n41 and n78).The drain efficiency of 47%-60%and output power higher than 40 dBm are measured.Good frequency selectivity in S-parameter measurements can be observed.展开更多
We report the design of a novel multiband metamaterial bandpass filter (BPF) in the terahertz (THz)-wave region. The designed BPF is composed of a metal-dielectric-metal sandwiched structure with three nested ring...We report the design of a novel multiband metamaterial bandpass filter (BPF) in the terahertz (THz)-wave region. The designed BPF is composed of a metal-dielectric-metal sandwiched structure with three nested rings on the top surface and a cross structure on the bottom surface. Full-wave simulation results show that the designed BPF has three transmission peaks at frequencies of 0.42, 1.27, and 1.86 THz with transmission rates of-0.87,-1.85, and-1.83 dB, respectively. Multi-reflection interference theory is introduced to explain the transmission mechanism of the designed triple-band BPF. The theoretical transmission spectrum is in good agreement with the full-wave simulated results. The designed BPF can maintain a stable performance as the incident angle varies from 0 to 30 for both transverse electric and transverse magnetic polarizations of the incident wave. The designed BPF can be potentially used in THz devices due to its multiband transmissions, polarization insensitivity, and stable wide-angle response in the THz region.展开更多
We investigate the guiding modes of spoof surface plasmon polaritons (SPPs) on a symmetric ultra-thin plasmonic structure. From the analysis, we deduce the operating frequency region of the single-mode propagation. ...We investigate the guiding modes of spoof surface plasmon polaritons (SPPs) on a symmetric ultra-thin plasmonic structure. From the analysis, we deduce the operating frequency region of the single-mode propagation. Based on this property, a spoof SPPs lowpass filter is then constituted in the microwave frequency. By introducing a transmission zero at the lower frequency band using a pair of stepped-impedance stubs, a wide passband filter is further realized. The proposed filter is fed by.a transducer composed of a microstrip line with a flaring ground. The simulated results show that the presented filter has an extremely wide upper stopband in addition to excellent passband filtering characteristics such as low loss, wide band, and high square ratio. A prototype passband filter is also fabricated to validate the predicted performances. The proposed spoof-SPPs filter is believed to be very promising for other surface waveguide components in microwave and terahertz bands.展开更多
This study is concerned with the diagnosis of discrepancies in a steel truss bridge by identifying dynamic properties from the vibration response signals of the bridges.The vibration response signals collected at brid...This study is concerned with the diagnosis of discrepancies in a steel truss bridge by identifying dynamic properties from the vibration response signals of the bridges.The vibration response signals collected at bridges under three different vehicular speeds of 10 km/hr,20 km/hr,and 30 km/hr are analyzed using statistical features such as kurtosis,magnitude of peak-to-peak,root mean square,crest factor as well as impulse factor in time domain,and Stockwell transform in the time-frequency domain.The considered statistical features except for kurtosis show uncertain behavior.The Stockwell transform showed low-resolution outcomes when the presence of noise in the recorded vibration responses.The elimination of noise and extraction of meaningful dynamic properties from the vibration responses is done by applying a new method which comes from the fusion of Hilbert transform with Spectral kurtosis and bandpass filtering.The outcomes obtained from Hilbert transform processed residual signals which are further filtered using bandpass filter show more robustness and accuracy in characterizing bridge modal frequencies from the noisy vibration responses.The proposed method produces a high-resolution frequency response which can unveil the joint discrepancy in the bridge structure.展开更多
A two Dimensional (2D) Photonic Crystal Ring Resonator (PCRR) based Bandpass Filter (BPF) is designed to cover C and L+U bands of Coarse Wavelength Division Multiplexing (CWDM) systems. It is devised with two quasi wa...A two Dimensional (2D) Photonic Crystal Ring Resonator (PCRR) based Bandpass Filter (BPF) is designed to cover C and L+U bands of Coarse Wavelength Division Multiplexing (CWDM) systems. It is devised with two quasi waveguides and a circular PCRR. The simulation results are obtained using 2D Finite Difference Time Domain (FDTD) method. The Photonic Band Gap (PBG) is calculated by Plane Wave Expansion (PWE) method. The BPFs allow the entire C-band (BPF1) and L+U bands (BPF2), which are extended from 1530 to 1565 nm (C band) and 1565 to 1675 nm (L+U bands). The computed bandwidth of BPF1 and BPF2 is 32 nm and 97 nm respectively. The size of the device is minimized from a scale of few tens of millimeters to the order of micrometers. The overall size of the BPF1 is around 12.8 μm × 11.4 μm and 11.4 μm × 11.4 μm for BPF2.展开更多
In this paper, a new signal separation method mainly for AM-FM components blended in noises is revisited based on the new derived time-varying bandpass filter (TVBF), which can separate the AM-FM components whose freq...In this paper, a new signal separation method mainly for AM-FM components blended in noises is revisited based on the new derived time-varying bandpass filter (TVBF), which can separate the AM-FM components whose frequencies have overlapped regions in Fourier transform domain and even have crossed points in time-frequency distribution (TFD) so that the proposed TVBF seems like a “soft-cutter” that cuts the frequency domain to snaky slices with rational physical sense. First, the Hilbert transform based decomposition is analyzed for the analysis of nonstationary signals. Based on the above analysis, a hypothesis under a certain condition that AM-FM components can be separated successfully based on Hilbert transform and the assisted signal is developed, which is supported by representative experiments and theoretical performance analyses on a error bound that is shown to be proportional to the product of frequency width and noise variance. The assisted signals are derived from the refined time-frequency distributions via image fusion and least squares optimization. Experiments on man-made and real-life data verify the efficiency of the proposed method and demonstrate the advantages over the other main methods.展开更多
In this study, we propose a novel resonator that is composed of a modified spiral with an embedded interdigital capacitor. A large ratio of the first spurious frequency to the fundamental resonant frequency is obtaine...In this study, we propose a novel resonator that is composed of a modified spiral with an embedded interdigital capacitor. A large ratio of the first spurious frequency to the fundamental resonant frequency is obtained, which is suitable for the design of filters with wide stopbands, and the circuit size is considerably reduced by embedding the interdigital structure in the spiral. For demonstration, a compact four-pole high temperature superconducting(HTS) filter with a center frequency of 568 MHz is designed and fabricated on double-sided YBCO film with a size of 11.4 mm×8.0 mm. The filter measurement shows excellent performance with an out-of-band rejection level better than 60.9 dB up to 3863 MHz.展开更多
By way of employing a multimode method together with the multimode transmission matrixtechnique based on the theory of planar circuits, the paper presents computer-aided design and optimized de-sign of bandpass fllter...By way of employing a multimode method together with the multimode transmission matrixtechnique based on the theory of planar circuits, the paper presents computer-aided design and optimized de-sign of bandpass fllters with dielectric resonators, and their sample was tested. The experimental result ofthe sample shows a reasonable agreement with the designed one.展开更多
A prototype IIR bandpass filter is derived from an analog bandpass filter using bilinear transformation. The formulas relating the IIR bandpass filter's coefficients with its centre frequency and bandwidth are obt...A prototype IIR bandpass filter is derived from an analog bandpass filter using bilinear transformation. The formulas relating the IIR bandpass filter's coefficients with its centre frequency and bandwidth are obtained. Using N sections of such filters, a cascade IIR bandpass filter is constructed. Based on given specifications and the formulas, the parameter N and the bandwidth of prototype filter can be obtained, and the required cascade IIR bandpass filter is obtained. The filter has a small set of coefficients with a simple structure, therefore is easy to design. The described approach is especially suitable for hardware implementation.展开更多
Two novel switched-capacitor(SC)bandpass filters using a single operational am-plifier(op amp)are presented.Optimal designs for minimizing capacitor spread are also given.Gain-bandwidth product(GB)effects of op amps o...Two novel switched-capacitor(SC)bandpass filters using a single operational am-plifier(op amp)are presented.Optimal designs for minimizing capacitor spread are also given.Gain-bandwidth product(GB)effects of op amps on the proposed SC circuits are taken intoconsideration.Comparisons with the proposed circuits and the circuits given by the literatureshow that the new circuits require less chip area in monolithic integration and are less sensitiveto the GB effects.展开更多
Modern electronic circuit requires compact,multifunctional technology in communication systems.However,it is very difficult due to the limitations in passive component miniaturization and the complication of fabricati...Modern electronic circuit requires compact,multifunctional technology in communication systems.However,it is very difficult due to the limitations in passive component miniaturization and the complication of fabrication process.The bandpass filter is one of the most important passive components in millimeter(mm)-wave communication system,attracting significant interest in three-dimension(3D) miniaturized design,which is few reported.In this paper,a bandpass filter structure using low-temperature co-fired ceramic(LTCC) technology,which is fully integrated in a system-in package(SIP) communication module,is presented for miniaturized and high reliable mm-wave application.The bandpass filter with 3D end-coupled microstrip resonators is implemented in order to achieve a high performance bandwidth characteristic.Specifically,all of the resonators are embedded into different ceramic layers to decrease the insertion loss and enhance the out-of-band rejection performance by optimizing the coupling coefficient and the coupling strength.A fence structure,which is formed by metal-filled via array with the gap less than quarter wavelength,is placed around the embedded bandpass filter to avoid electromagnetic(EM) interference problem in multilayer structure.This structural model is validated through actual LTCC process.The bandpass filter is successfully manufactured by modifying the co-fireablity characteristics,adjusting the sintering profile,releasing the interfacial stress,and reducing the shrinkage mismatch with different materials.Measured results show good performance and agree well with the high frequency EM full wave simulation.The influence of layer thickness and dielectric constant on the frequency response in fabricated process is analyzed,where thicker ceramic sheets let the filter response shift to higher frequency.Moreover,measured S-parameters denote the center frequency is also strongly influenced by the variation of ceramic material's dielectric constants.By analyzing the relationship between the characteristics of the ceramic tape and the center frequency of the filter,both theoretical and experimental data are accumulated for broadening application filed.With the coupling resonators embedded into the ceramic layers,the bandpass filter exhibits advantages of small size and high reliability compared to conventional planar filter structure,which makes the bandpass filter suitable for SIP communicational application.展开更多
In this paper, the variational method combined with Green's function is used to analyze the characteristics of suspended, stripline. The result is in good agreement with references. The design of mm-wave end-coupl...In this paper, the variational method combined with Green's function is used to analyze the characteristics of suspended, stripline. The result is in good agreement with references. The design of mm-wave end-coupled bandpass filter with suspended substrate is discussed. The computer programs for design of suspended stripline and bandpass filter are established.展开更多
This paper reviews the state-of-the-art filter designs for 60 GHz applications. The most promising filter solutions at this frequency include fiher-in-package where the filter itself is design in the packaging platfor...This paper reviews the state-of-the-art filter designs for 60 GHz applications. The most promising filter solutions at this frequency include fiher-in-package where the filter itself is design in the packaging platform and filter-on-chip which is an on-chip filter co-design for miniaturized system size with low packaging cost. Design methodology, design technology, key performance parameters, similarities and dift)rences, advantages and drawbacks, and future trends are explored and studied. Filters in the printed circuit board (PCB), low temperature co-fired ceramics (LTCC), organie material, and bipolar complementary metal oxide semicomtuctor (BiCMOS) chips are summarized and compared in details. Future design trends and challenges are also given after the review.展开更多
A high performance Balun BandPass Filter (BPF) with capacitively loaded multiple coupled lines with very simple structure is proposed in this paper, this structure realizes simultaneous size reduction and superior har...A high performance Balun BandPass Filter (BPF) with capacitively loaded multiple coupled lines with very simple structure is proposed in this paper, this structure realizes simultaneous size reduction and superior harmonic response suppression performance in bandpass filtering meanwhile good differential performance of the Balun. The theory of this structure for unbalanced input into balanced output has been studied in this paper and a proper Balun and BPF characteristic by the symmetric feeding and skew symmetric feeding have been obtained to prove the theory. The enter frequency of the fabricated Balun-BPF is operated at 2.45 GHz with 6.93% Fractional Band Width (FBW), and this frequency is used for Bluetooth and some other communication systems. The differences between the two outputs are 180°± 1.92° in phase and within 0.33 dB in magnitude. At f0, the amplitude imbalance and phase difference are within 0.25 dB and 180.86°, respectively. The measured frequency responses agree well with the simulated ones. With the theoretical analyses and practical results, it is shown that the proposed one has the advantages of simple structure, convenient analysis and good performance of both BPF and Balun.展开更多
In this paper, the resonant frequency of a dual\|mode dielectric resonator is calculated using a finite difference time\|domain method. A new type of bandpass filter is designed with the calculated coupling coefficien...In this paper, the resonant frequency of a dual\|mode dielectric resonator is calculated using a finite difference time\|domain method. A new type of bandpass filter is designed with the calculated coupling coefficient. The filter designed in this paper has reached the design goal, verified by simulation with Ansoft HFSS.展开更多
In this paper,a Slotted Stepped-Impedance Resonator (SSIR) is proposed.Due to the slots in the low-impedance section of the conventional SIR,the new resonator has a lower fundamental resonance f0 and can provide a pot...In this paper,a Slotted Stepped-Impedance Resonator (SSIR) is proposed.Due to the slots in the low-impedance section of the conventional SIR,the new resonator has a lower fundamental resonance f0 and can provide a potential finite transmission zero fz close to f0.Based on the proposed SSIR,a fourth-order Chebychev BandPass Filter (BPF) is designed at f0=1 GHz.The measured results show that a better than-65 dB rejection is achieved on both the lower and the upper stopband.Moreover,the new filter has a wide-30 dB rejection upper stopband from 1.13f0 to 6.52f0.The fabricated filter exhibits a size of The new filter has a planar topology and is easily integrated with modern portable communication systems.展开更多
The two proposed filters described here satisfy the Federal Communications Commission Ultra-wideband (FCC-UWB) specifications and also control the center frequency and bandwidth of the filters passband. These filters ...The two proposed filters described here satisfy the Federal Communications Commission Ultra-wideband (FCC-UWB) specifications and also control the center frequency and bandwidth of the filters passband. These filters consist of two distinguishing parts, Electromagnetic bandgap (EBG)-embedded multiple- mode resonator (MMR) and interdigital coupled lines to realize high performance in the operation band with a compact size of 14.0 mm × 10.1 mm. The main advantage of the two proposed filters is that three different bands are tuned. The 1st tuned band is from 3.5 GHz to 11.4 GHz for the first filter and from 3.1 GHz to 11.6 GHz for the second proposed filter, respectively. The 2nd tuned band is from 3.5 GHz to 7.5 GHz for the first filter and from 3.1 GHz to 7.8 GHz for the second proposed filter, respectively. While the 3rd tuned band of the first proposed filter is from 3.5 GHz to 5.9 GHz and from 3.1 GHz to 5.8 GHz for the second proposed filter. The bandwidth of the filters can be changed by increasing the length of the outer open circuited stubs which are controlled by using switching matrix equipment (mini circuit, replacement of PIN diodes). To validate the design theory, a reconfigurable UWB bandpass filters (BPFs) with EBG Embedded MMR are designed, fabricated and measured. Good agreement is found between simulated and measured results.展开更多
An ultra-wideband bandpass filter(BPF)with a wide out-of-band rejection based on a surface plasmonic waveguide(SPW)slotline with ring grooves is designed and analyzed.A paired microstrip-to-slotline transition is desi...An ultra-wideband bandpass filter(BPF)with a wide out-of-band rejection based on a surface plasmonic waveguide(SPW)slotline with ring grooves is designed and analyzed.A paired microstrip-to-slotline transition is designed for quasiTEM to TM mode conversion by using a microstrip line with a circular pad and the slotline with the same circular slot.The mode conversion between the TM and the surface plasmon polariton(SPP)mode is realized by using a gradient slotline with ring grooves and an impedance matching technique.The upper cut-off frequencies of the passband can be adjusted by using these proposed SPP units,while the lower frequencies of the passband are created by using the microstrip-toslotline transitions to give an ultra-wideband BPF.The dispersion curves of SPP units,electric field distribution,and the transmission spectra of the proposed ultra-wideband bandpass filter are all calculated and analyzed by the finite-difference time-domain(FDTD)method.The simulated results show that the presented filter has good performance including a wide3-dB bandwidth of 149%from 0.57 GHz to 3.93 GHz,an extremely wide 40-dB upper-band rejection from 4.2 GHz to18.5 GHz,and low loss and high selectivity in the passband.To prove the design validity,a prototype of the BPF has been manufactured and measured,showing a reasonable agreement with simulation results.The unique features of the proposed BPF may make it applicable for integrated circuit and plasmonic devices in microwave or THz frequency ranges.展开更多
A miniaturized square resonator bandpass filter with circular stubs is designed, fabricated, and characterized. Analytical calculations were carried out to determine the critical filter parameters and the design was o...A miniaturized square resonator bandpass filter with circular stubs is designed, fabricated, and characterized. Analytical calculations were carried out to determine the critical filter parameters and the design was optimized using a 3D electromagnetic finite-element solver. The measured results were in good agreement with the designed results. The proposed filter exhibits significant improvement in bandwidth compared to the conventional square resonator bandpass filters.展开更多
Miniaturized Ultra-Wideband (UWB) microstrip bandpass filter with wide passband is presented. The filter is developed based on modified multiple mode resonator, which is formed by transversely attaching three pairs of...Miniaturized Ultra-Wideband (UWB) microstrip bandpass filter with wide passband is presented. The filter is developed based on modified multiple mode resonator, which is formed by transversely attaching three pairs of non-uniform and folded stubs with lowpass and highpass sections. Both sides of high-impedance section are linked with two feed lines via direct coupled lines, resulting UWB bandpass filter. The designed filter provides 7 GHz passband between 2.5 and 9.5 GHz with approximately, –0.5 dB insertion loss, –35 dB minimum return loss at 6.85 GHz, linear phase over the passband and 110% of fractional bandwidth at –3 dB. The computed group delay variation in the passband for the filter is 0.02 ns. The overall dimension of the filter is 10.7 mm (length) × 3 mm (width) × 1.6 mm (thickness).展开更多
基金supported by National Natural Science Foundations of China (No.61971052 and No.U20A20203)Key Research and Development Project of Guangdong Province (2020B0101080001)
文摘In this paper,a 5G wideband power amplifier(PA)with bandpass filtering response is synthesized using a bandwidth-extended bandpass filter as the matching network(MN).In this structure,the bandwidth(θ_(C))is defined as a variable in the closedform equations provided by the microstrip bandpass filter.It can be extended over a wide range only by changing the characteristic impedances of the structure.Different from the other wideband MNs,the extension of bandwidth does not increase the complexity of the structure(order n is fixed).In addition,based on the bandwidth-extended structure,the wideband design of bandpass filtering PA is not limited to the fixed bandwidth of the specific filter structure.The theoretical analysis of the MN and the design flow of the PA are provided in this design.The fabricated bandpass filtering PA can support almost one-octave bandwidth(2-3.8 GHz),covering the two 5G bands(n41 and n78).The drain efficiency of 47%-60%and output power higher than 40 dBm are measured.Good frequency selectivity in S-parameter measurements can be observed.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.11504418,11447033,and 61372048)the Fundamental Research Funds for the Central Universities,China(Grant No.2015XKMS075)
文摘We report the design of a novel multiband metamaterial bandpass filter (BPF) in the terahertz (THz)-wave region. The designed BPF is composed of a metal-dielectric-metal sandwiched structure with three nested rings on the top surface and a cross structure on the bottom surface. Full-wave simulation results show that the designed BPF has three transmission peaks at frequencies of 0.42, 1.27, and 1.86 THz with transmission rates of-0.87,-1.85, and-1.83 dB, respectively. Multi-reflection interference theory is introduced to explain the transmission mechanism of the designed triple-band BPF. The theoretical transmission spectrum is in good agreement with the full-wave simulated results. The designed BPF can maintain a stable performance as the incident angle varies from 0 to 30 for both transverse electric and transverse magnetic polarizations of the incident wave. The designed BPF can be potentially used in THz devices due to its multiband transmissions, polarization insensitivity, and stable wide-angle response in the THz region.
基金Project supported by the Key Grant Project of Ministry of Education of China(Grant No.313029)the FDCT Research Grant from Macao Science and Technology Development Fund,China(Grant No.051/2014/A1)the Multi-Year Research Grant from University of Macao,Macao SAR,China(Grant No.MYRG2014-00079-FST)
文摘We investigate the guiding modes of spoof surface plasmon polaritons (SPPs) on a symmetric ultra-thin plasmonic structure. From the analysis, we deduce the operating frequency region of the single-mode propagation. Based on this property, a spoof SPPs lowpass filter is then constituted in the microwave frequency. By introducing a transmission zero at the lower frequency band using a pair of stepped-impedance stubs, a wide passband filter is further realized. The proposed filter is fed by.a transducer composed of a microstrip line with a flaring ground. The simulated results show that the presented filter has an extremely wide upper stopband in addition to excellent passband filtering characteristics such as low loss, wide band, and high square ratio. A prototype passband filter is also fabricated to validate the predicted performances. The proposed spoof-SPPs filter is believed to be very promising for other surface waveguide components in microwave and terahertz bands.
文摘This study is concerned with the diagnosis of discrepancies in a steel truss bridge by identifying dynamic properties from the vibration response signals of the bridges.The vibration response signals collected at bridges under three different vehicular speeds of 10 km/hr,20 km/hr,and 30 km/hr are analyzed using statistical features such as kurtosis,magnitude of peak-to-peak,root mean square,crest factor as well as impulse factor in time domain,and Stockwell transform in the time-frequency domain.The considered statistical features except for kurtosis show uncertain behavior.The Stockwell transform showed low-resolution outcomes when the presence of noise in the recorded vibration responses.The elimination of noise and extraction of meaningful dynamic properties from the vibration responses is done by applying a new method which comes from the fusion of Hilbert transform with Spectral kurtosis and bandpass filtering.The outcomes obtained from Hilbert transform processed residual signals which are further filtered using bandpass filter show more robustness and accuracy in characterizing bridge modal frequencies from the noisy vibration responses.The proposed method produces a high-resolution frequency response which can unveil the joint discrepancy in the bridge structure.
文摘A two Dimensional (2D) Photonic Crystal Ring Resonator (PCRR) based Bandpass Filter (BPF) is designed to cover C and L+U bands of Coarse Wavelength Division Multiplexing (CWDM) systems. It is devised with two quasi waveguides and a circular PCRR. The simulation results are obtained using 2D Finite Difference Time Domain (FDTD) method. The Photonic Band Gap (PBG) is calculated by Plane Wave Expansion (PWE) method. The BPFs allow the entire C-band (BPF1) and L+U bands (BPF2), which are extended from 1530 to 1565 nm (C band) and 1565 to 1675 nm (L+U bands). The computed bandwidth of BPF1 and BPF2 is 32 nm and 97 nm respectively. The size of the device is minimized from a scale of few tens of millimeters to the order of micrometers. The overall size of the BPF1 is around 12.8 μm × 11.4 μm and 11.4 μm × 11.4 μm for BPF2.
文摘In this paper, a new signal separation method mainly for AM-FM components blended in noises is revisited based on the new derived time-varying bandpass filter (TVBF), which can separate the AM-FM components whose frequencies have overlapped regions in Fourier transform domain and even have crossed points in time-frequency distribution (TFD) so that the proposed TVBF seems like a “soft-cutter” that cuts the frequency domain to snaky slices with rational physical sense. First, the Hilbert transform based decomposition is analyzed for the analysis of nonstationary signals. Based on the above analysis, a hypothesis under a certain condition that AM-FM components can be separated successfully based on Hilbert transform and the assisted signal is developed, which is supported by representative experiments and theoretical performance analyses on a error bound that is shown to be proportional to the product of frequency width and noise variance. The assisted signals are derived from the refined time-frequency distributions via image fusion and least squares optimization. Experiments on man-made and real-life data verify the efficiency of the proposed method and demonstrate the advantages over the other main methods.
基金supported by the National Key Scientific Instrument and Equipment Development Project,China(Grant No.2014YQ030975)the National Natural Science Foundation of China(Grant Nos.61371009 and 61401282)
文摘In this study, we propose a novel resonator that is composed of a modified spiral with an embedded interdigital capacitor. A large ratio of the first spurious frequency to the fundamental resonant frequency is obtained, which is suitable for the design of filters with wide stopbands, and the circuit size is considerably reduced by embedding the interdigital structure in the spiral. For demonstration, a compact four-pole high temperature superconducting(HTS) filter with a center frequency of 568 MHz is designed and fabricated on double-sided YBCO film with a size of 11.4 mm×8.0 mm. The filter measurement shows excellent performance with an out-of-band rejection level better than 60.9 dB up to 3863 MHz.
文摘By way of employing a multimode method together with the multimode transmission matrixtechnique based on the theory of planar circuits, the paper presents computer-aided design and optimized de-sign of bandpass fllters with dielectric resonators, and their sample was tested. The experimental result ofthe sample shows a reasonable agreement with the designed one.
文摘A prototype IIR bandpass filter is derived from an analog bandpass filter using bilinear transformation. The formulas relating the IIR bandpass filter's coefficients with its centre frequency and bandwidth are obtained. Using N sections of such filters, a cascade IIR bandpass filter is constructed. Based on given specifications and the formulas, the parameter N and the bandwidth of prototype filter can be obtained, and the required cascade IIR bandpass filter is obtained. The filter has a small set of coefficients with a simple structure, therefore is easy to design. The described approach is especially suitable for hardware implementation.
文摘Two novel switched-capacitor(SC)bandpass filters using a single operational am-plifier(op amp)are presented.Optimal designs for minimizing capacitor spread are also given.Gain-bandwidth product(GB)effects of op amps on the proposed SC circuits are taken intoconsideration.Comparisons with the proposed circuits and the circuits given by the literatureshow that the new circuits require less chip area in monolithic integration and are less sensitiveto the GB effects.
基金supported by Research Fund for the Doctoral Program of Higher Education of China(Grant No.20060614021)Sichuan Provincial Fundamental Research of China(Grant No.2008JY0057),Fundamental Research Funds for the Central Universities of China(Grant No.ZYGX2009J091)
文摘Modern electronic circuit requires compact,multifunctional technology in communication systems.However,it is very difficult due to the limitations in passive component miniaturization and the complication of fabrication process.The bandpass filter is one of the most important passive components in millimeter(mm)-wave communication system,attracting significant interest in three-dimension(3D) miniaturized design,which is few reported.In this paper,a bandpass filter structure using low-temperature co-fired ceramic(LTCC) technology,which is fully integrated in a system-in package(SIP) communication module,is presented for miniaturized and high reliable mm-wave application.The bandpass filter with 3D end-coupled microstrip resonators is implemented in order to achieve a high performance bandwidth characteristic.Specifically,all of the resonators are embedded into different ceramic layers to decrease the insertion loss and enhance the out-of-band rejection performance by optimizing the coupling coefficient and the coupling strength.A fence structure,which is formed by metal-filled via array with the gap less than quarter wavelength,is placed around the embedded bandpass filter to avoid electromagnetic(EM) interference problem in multilayer structure.This structural model is validated through actual LTCC process.The bandpass filter is successfully manufactured by modifying the co-fireablity characteristics,adjusting the sintering profile,releasing the interfacial stress,and reducing the shrinkage mismatch with different materials.Measured results show good performance and agree well with the high frequency EM full wave simulation.The influence of layer thickness and dielectric constant on the frequency response in fabricated process is analyzed,where thicker ceramic sheets let the filter response shift to higher frequency.Moreover,measured S-parameters denote the center frequency is also strongly influenced by the variation of ceramic material's dielectric constants.By analyzing the relationship between the characteristics of the ceramic tape and the center frequency of the filter,both theoretical and experimental data are accumulated for broadening application filed.With the coupling resonators embedded into the ceramic layers,the bandpass filter exhibits advantages of small size and high reliability compared to conventional planar filter structure,which makes the bandpass filter suitable for SIP communicational application.
文摘In this paper, the variational method combined with Green's function is used to analyze the characteristics of suspended, stripline. The result is in good agreement with references. The design of mm-wave end-coupled bandpass filter with suspended substrate is discussed. The computer programs for design of suspended stripline and bandpass filter are established.
文摘This paper reviews the state-of-the-art filter designs for 60 GHz applications. The most promising filter solutions at this frequency include fiher-in-package where the filter itself is design in the packaging platform and filter-on-chip which is an on-chip filter co-design for miniaturized system size with low packaging cost. Design methodology, design technology, key performance parameters, similarities and dift)rences, advantages and drawbacks, and future trends are explored and studied. Filters in the printed circuit board (PCB), low temperature co-fired ceramics (LTCC), organie material, and bipolar complementary metal oxide semicomtuctor (BiCMOS) chips are summarized and compared in details. Future design trends and challenges are also given after the review.
文摘A high performance Balun BandPass Filter (BPF) with capacitively loaded multiple coupled lines with very simple structure is proposed in this paper, this structure realizes simultaneous size reduction and superior harmonic response suppression performance in bandpass filtering meanwhile good differential performance of the Balun. The theory of this structure for unbalanced input into balanced output has been studied in this paper and a proper Balun and BPF characteristic by the symmetric feeding and skew symmetric feeding have been obtained to prove the theory. The enter frequency of the fabricated Balun-BPF is operated at 2.45 GHz with 6.93% Fractional Band Width (FBW), and this frequency is used for Bluetooth and some other communication systems. The differences between the two outputs are 180°± 1.92° in phase and within 0.33 dB in magnitude. At f0, the amplitude imbalance and phase difference are within 0.25 dB and 180.86°, respectively. The measured frequency responses agree well with the simulated ones. With the theoretical analyses and practical results, it is shown that the proposed one has the advantages of simple structure, convenient analysis and good performance of both BPF and Balun.
文摘In this paper, the resonant frequency of a dual\|mode dielectric resonator is calculated using a finite difference time\|domain method. A new type of bandpass filter is designed with the calculated coupling coefficient. The filter designed in this paper has reached the design goal, verified by simulation with Ansoft HFSS.
文摘In this paper,a Slotted Stepped-Impedance Resonator (SSIR) is proposed.Due to the slots in the low-impedance section of the conventional SIR,the new resonator has a lower fundamental resonance f0 and can provide a potential finite transmission zero fz close to f0.Based on the proposed SSIR,a fourth-order Chebychev BandPass Filter (BPF) is designed at f0=1 GHz.The measured results show that a better than-65 dB rejection is achieved on both the lower and the upper stopband.Moreover,the new filter has a wide-30 dB rejection upper stopband from 1.13f0 to 6.52f0.The fabricated filter exhibits a size of The new filter has a planar topology and is easily integrated with modern portable communication systems.
文摘The two proposed filters described here satisfy the Federal Communications Commission Ultra-wideband (FCC-UWB) specifications and also control the center frequency and bandwidth of the filters passband. These filters consist of two distinguishing parts, Electromagnetic bandgap (EBG)-embedded multiple- mode resonator (MMR) and interdigital coupled lines to realize high performance in the operation band with a compact size of 14.0 mm × 10.1 mm. The main advantage of the two proposed filters is that three different bands are tuned. The 1st tuned band is from 3.5 GHz to 11.4 GHz for the first filter and from 3.1 GHz to 11.6 GHz for the second proposed filter, respectively. The 2nd tuned band is from 3.5 GHz to 7.5 GHz for the first filter and from 3.1 GHz to 7.8 GHz for the second proposed filter, respectively. While the 3rd tuned band of the first proposed filter is from 3.5 GHz to 5.9 GHz and from 3.1 GHz to 5.8 GHz for the second proposed filter. The bandwidth of the filters can be changed by increasing the length of the outer open circuited stubs which are controlled by using switching matrix equipment (mini circuit, replacement of PIN diodes). To validate the design theory, a reconfigurable UWB bandpass filters (BPFs) with EBG Embedded MMR are designed, fabricated and measured. Good agreement is found between simulated and measured results.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.U2141232,62071221,and 62071442)the Aeronautical Science Foundation of China(Grant No.2019ZA037001)。
文摘An ultra-wideband bandpass filter(BPF)with a wide out-of-band rejection based on a surface plasmonic waveguide(SPW)slotline with ring grooves is designed and analyzed.A paired microstrip-to-slotline transition is designed for quasiTEM to TM mode conversion by using a microstrip line with a circular pad and the slotline with the same circular slot.The mode conversion between the TM and the surface plasmon polariton(SPP)mode is realized by using a gradient slotline with ring grooves and an impedance matching technique.The upper cut-off frequencies of the passband can be adjusted by using these proposed SPP units,while the lower frequencies of the passband are created by using the microstrip-toslotline transitions to give an ultra-wideband BPF.The dispersion curves of SPP units,electric field distribution,and the transmission spectra of the proposed ultra-wideband bandpass filter are all calculated and analyzed by the finite-difference time-domain(FDTD)method.The simulated results show that the presented filter has good performance including a wide3-dB bandwidth of 149%from 0.57 GHz to 3.93 GHz,an extremely wide 40-dB upper-band rejection from 4.2 GHz to18.5 GHz,and low loss and high selectivity in the passband.To prove the design validity,a prototype of the BPF has been manufactured and measured,showing a reasonable agreement with simulation results.The unique features of the proposed BPF may make it applicable for integrated circuit and plasmonic devices in microwave or THz frequency ranges.
文摘A miniaturized square resonator bandpass filter with circular stubs is designed, fabricated, and characterized. Analytical calculations were carried out to determine the critical filter parameters and the design was optimized using a 3D electromagnetic finite-element solver. The measured results were in good agreement with the designed results. The proposed filter exhibits significant improvement in bandwidth compared to the conventional square resonator bandpass filters.
文摘Miniaturized Ultra-Wideband (UWB) microstrip bandpass filter with wide passband is presented. The filter is developed based on modified multiple mode resonator, which is formed by transversely attaching three pairs of non-uniform and folded stubs with lowpass and highpass sections. Both sides of high-impedance section are linked with two feed lines via direct coupled lines, resulting UWB bandpass filter. The designed filter provides 7 GHz passband between 2.5 and 9.5 GHz with approximately, –0.5 dB insertion loss, –35 dB minimum return loss at 6.85 GHz, linear phase over the passband and 110% of fractional bandwidth at –3 dB. The computed group delay variation in the passband for the filter is 0.02 ns. The overall dimension of the filter is 10.7 mm (length) × 3 mm (width) × 1.6 mm (thickness).