Exceptional reversed yield strength asymmetry in a rare-earth free Mg alloy containing quasicrystal precipitates

This work reports an exceptional reversed yield strength asymmetry at room temperature for a rare-earth free magnesium alloy containing a mass of fine dispersed quasicrystal(I-phase)precipitates.Although exhibiting traditional basal texture,it owns an exceptional CYS/TYS as high as~1.17.Electron back-scattered diffraction(EBSD)and transmission electron microscopy(TEM)examinations indicate pyramidal and prismatic dislocations plus tensile twinning being activated after immediate yielding in compression while basal and non-basal dislocations in tension.I-phase particles transferred the concentrated stress by self-twinning to provide the driving force for tensile twin initiating in neighboring grains,thereby significantly increasing the critical resolved shear stress of tensile twinning to possibly the level of pyramidal slip,finally leading to the dominance of pyramidal slip plus tensile twinning in texture grains.This results in a higher contribution on yield strength by~55 MPa in compression than in tension,which reasonably agrees with the experimental yield strength difference(~38 MPa).It can be concluded that I-phase particles influence deformation modes in tension and in compression,finally result in reversed yield strength asymmetry.

Microstructure,texture evolution and yield strength symmetry improvement of as-extruded ZK60 Mg alloy via multi-directional impact forging

Multi-direction impact forging(MDIF)was applied to the as-extruded ZK60 Mg alloy,and the microstructure,texture evolution and yield strength symmetry were investigated in the current study.The results showed that the average grain size of forged piece was greatly refined to 5.3μm after 120 forging passes,which was ascribed to the segmenting effect of{10–12}twins and the subsequent multiple rounds of dynamic recrystallization(DRX).A great deal of{10–12}twins were activated at the beginning of MDIF process,which played an important role in grain refinement.With forging proceeding,continuous and discontinuous DRX were successively activated,resulting in the fully DRXed microstructure.Meanwhile,the forged piece exhibited a unique four-peak texture,and the initial<10-10>//ED fiber texture component gradually evolved into multiple texture components composed of<0001>//FFD(first forging direction)and<11–20>//FFD texture.The special strain path was the key to the formation of the unique four-peak texture.The{10–12}twinning and basal slip were two dominant factors to the evolution of texture during MDIF process.Grain strengthening and dislocation strengthening were two main strengthening mechanisms of the forged piece.Besides,the symmetry of yield strength was greatly improved by MDIF process.

Magnetization-Enhanced Dislocation Motion and Decreased Yield Strength of 60Fe40Ni Alloy

Using a special constant deflection device, the changes in dislocation configuration ahead of a loaded crack tip for 60Fe40Ni alloy. before and after magnetization in a magnetic field, have been studied in TEM. The results showed that the magnetization for 60Fe40Ni alloy could enhance dislocation emission, multiplication and motion. Also, the mechanical properties of 60Fe40Ni alloy, in air and in the magnetic field respectively have been investigated using the slow strain rate tension. And the results indicated that magnetization could make the yield strength corresponding to decrease by 26 percent, but did not influence the ultimate tensile strength and the fracture strain, which showed that magnetization could enhance plastic deformation.

Effect of Ti content on the yield strength of Nb-Ti microalloyed steels

The hot rolling experiment investigates into the relationship between the microstructures and the mechanical properties of Nb-Ti microalloyed steels with various Ti contents. The results indicate that the effect of the bainite fraction of Nb-Ti microalloyed steels on the yield strength of the steels is not related to Ti content, while the slope of the Hall- Petch relationship decreases with the increase of Ti content. Accordingly, the Misra model for the yield strength of Nb-Ti microalloyed steels is modified, and the factors which cause the change in the slope of Hall-Petch relationship are discussed.

An Application of the Modified Shear Lag Model to Study the Influence of Thermal Residual Stresses on the Stiffness and Yield Strength of Short Fiber Reinforced Metal Matrix Composites

The modified shear lag model proposed recently was applied to calculate thermal residual stresses and subsequent stress distributions under tensile and compressive loadings. The expressions for the elastic moduli and the yield strengths under tensile and compressive loadings were derived which take account of thermal residual stresses. The asymmetries in the elastic modulus and the yield strength were interpreted using the derived expressions and the obtained results of the stress calculations. The model predictions have exhibited good agreements with the experimental results and also with the other theoretical predictions

Unusual softening behavior of yield strength in niobium at high pressures

In situ synchrotron angle-dispersive x-ray diffraction experiments on niobium powders have been conducted at pressures up to 61 GPa and room temperature using the diamond anvil cell technique. From the full width at half maximum of the measured diffraction lines, the yield strength was derived with the line-width analysis theory. The niobium powder sample was found to be compressed more packed firstly and then yielded at~14 GPa–18 GPa. Following an initial increase in the yield strength with pressure, an obvious decrease was observed occurring at ~42 GPa–47 GPa accompanying with a typical pressure dependence above 47 GPa. The experimentally observed anomalous softening of the yield strength in niobium surprisingly follows the trend of the predicted unusual softening in the shear modulus by the recent theoretical investigations. The possible mechanisms, applicable to interpret the yield strength softening of materials at high pressure,were also discussed in detail.

SURFACE YIELD STRENGTH AND FATIGUE LIMIT FOR STEELS

The surface yield strength(σ_(ms))for various carbon steels was studied by means of X-ray diffraction method.The results showed that it is.far below the bulk yield strength,and is the resistance against plastic deformation in the surface layer.The smooth fatigue limit is associ- ated with crack initiation which is a result of accumulation of plastic deformation.Experimen- tal results showed the relation of smooth fatigue limit for 50% survival with σ_(ms)is σ_(ms)=0.81 tO 1.02 σ_(-1)for different steels.The smooth fatigue limit of a medium carbon steel for 99.9% survival with σ_(ms)is σ_(ms)=0.98 tO 1.10 σ_(-1).It is less expensive and time consuming to measure σ_(ms)than σ_(-1).

Yield strength of attached copper film

Variation of stress in attached copper film with an applied strain is measured by X-ray diffraction combined with a four-point bending method. A lower slope of the initial elastic segment of the curve of X-ray measured stress versus applied strain results from incomplete elastic strain transferred from the substrate to the film due to insufficiently strong interface cohesion. So the slope of the initial elastic segment of the X-ray stress （or X-ray strain directly） of the film against the substrate applied strain may be used to measure the film-substrate cohesive strength. The yield strength of the attached copper film is much higher than that of the bulk material and varies linearly with the inverse of the film thickness.

Effective Yield Strength for Material Powder Consolidated at Stage II Compaction

This work is concerned with the estimation from the outside of effective yield strength for the stage II consolidated material package of axisymmetric solid particles. Once an appropriate simple representative axisymmetric unit cell is chosen, the kinematical approach of the yield design homogenization method is used in order to obtain external estimates which has been found depending on the loading history (isostatic and closed die compactions) as well as on the relative density of the material powder. For comparison purpose, finite element simulations that describe the behavior of spherical elastic plastic particles uniformly distributed inside the material powder are carried out.

A New Modification to Shear Lag Model as Applied to Stiffness and Yield Strength of Short Fiber Reinforced Metal Matrix Composites

A new modification for the shear lag model is given and the expressions for the stiffness and yield Strength of short fiber metal matri×composite are derived. These expressions are then compared with our experimental data in a SiCw/Al-Li T6 composite and the published experimental data on different SiCw/Al T6 composites and also compared with the previous shear lag models and the other theoretical models.

Influence of pre- plastic deformation on thermal residual stress and yield strength of SiC_w/Al composites

With a micro mechanical model, the feasibility of modification of thermal residual stress of the composites treated by tensile pre plastic deformation was analyzed. The relationship between pre plastic strain and variation of thermal residual stress was established. By using the method of tensile pre plastic deformation, the thermal residual stress in 20%SiC w/6061Al composites was modified. The results show that, with increasing tensile pre plastic strain, the tensile residual stress in the matrix was decreased to zero gradually, and then it was turned into compressive stress. By comparison, it was found that the changing tendency of the test results is similar to that of theoretical analysis. In addition, due to pre plastic deformation, the dislocation density in the matrix was increased, and the yield strength of the composites was improved. The increasing yield strength is mainly due to the decreasing tensile residual stress and the changing of distribution of dislocation in the matrix.

Mechanical model for yield strength of nanocrystalline materials under high strain rate loading

To understand the high strain rate deformation mechanism and determine the grain size,strain rate and porosity dependent yield strength of nanocrystalline materials,a new mechanical model based on the deformation mechanism of nanocrystalline materials under high strain rate loading was developed.As a first step of the research,the yield behavior of the nanocrystalline materials under high strain rate loading was mainly concerned in the model and uniform deformation was assumed for simplification.Nanocrystalline materials were treated as composites consisting of grain interior phase and grain boundary phase,and grain interior and grain boundary deformation mechanisms under high strain rate loading were analyzed,then Voigt model was applied to coupling grain boundary constitutive relation with mechanical model for grain interior phase to describe the overall yield mechanical behavior of nanocrystalline materials.The predictions by the developed model on the yield strength of nanocrysatlline materials at high strain rates show good agreements with various experimental data.Further discussion was presented for calculation results and relative experimental observations.

Effect of low temperature treatment on tensile yield strength of SiC_w/6061 Al alloy composites

The effect of the low temperature treatment at -78 ℃ and -196 ℃ on the microstructure and properties of 18%SiC w/6061(volume fraction) Al alloy composites of as squeeze casting were studied. The results show that, after the low temperature treatment, the dislocation density in matrix increases, and the residual stress of the matrix decreases, as well as the tensile yield strength of the composites improves. The high residual stress exists in the matrix of the composites of as original squeeze casting. The mismatch degree between the matrix and SiC w phases increases during the low temperature treatment. The matrix undergoes the tensile plastic deformation during the cooling procedure. On the contrary, the matrix encountered an elastic unloading procedure during the heating up process from low temperature to room temperature. The increase of dislocation density and the decrease of residual stress in the matrix are the main reason of the improvement for tensile yield strength of the composites.

Study on Anisotropy and Punching Yield Strength of Knitted Fabrics

In terms of the structural characteristics, knitted fabrics are described as plane orthotropic body with two symmetric axes, and the stress in different direction is approximately linear with strain before the yield point.The punching yield strength can be predicted theoretically by developing a mathematical equation from anisotropic effect of knitted fabrics. The experimental results demonstrate the applicability of theoretical formula. Analyses also reveal that the factors influencing three-dimensional deforming performance can be divided into two categories: fiber-yarn-fabric structural features and deforming condition.

Composition design of high yield strength points in single-phase Co-Cr-Fe-Ni-Mo multi-principal element alloys system based on electronegativity,thermodynamic calculations,and machine learning

A method which combines electronegativity difference,CALculation of PHAse Diagrams(CALPHAD) and machine learning has been proposed to efficiently screen the high yield strength regions in Co-Cr-Fe-Ni-Mo multi-component phase diagram.First,the single-phase region at a certain annealing temperature is obtained by combining CALPHAD method and machine learning,to avoid the formation of brittle phases.Then high yield strength points in the single-phase region are selected by electronegativity difference.The yield strength and plastic deformation behavior of the designed Co_(14)Cr_(30)Ni_(50)Mo_(6)alloy are measured to evaluate the proposed method.The validation experiments indicate this method is effective to predict high yield strength points in the whole compositional space.Meanwhile,the interactions between the high density of shear bands and dislocations contribute to the high ductility and good work hardening ability of Co_(14)Cr_(30)Ni_(50)Mo_(6)alloy.The method is helpful and instructive to property-oriented compositional design for multi-principal element alloys.

Yield strength of“brittle”metallic glass

“Brittle”metallic glass(MG)usually fractures catastrophically in a shattering mode under macroscopic compression,because cleavage cracking of splitting that originates from extrinsic flaws dominates the failure of such alloys,which brings challenges for studying yield strength.Here we show that the plastic yielding behavior in a brittle Fe-based MG can be successfully activated by decreasing the sample size to micrometer scale to avoid the possible large tensile stress concentrators.The yield strength was found to be at least 33%higher than the fracture strength measured with bulk samples for the present brittle MG.The results further demonstrate that the critical stresses for shear band initiation and propagation are size-independent,while the required stress for cleavage cracking increases with decreasing sample size.The competition of thermodynamic driving forces between the two processes of shear banding and cleavage cracking hence leads to the size-induced brittle-to ductile-transition.These findings clarify the physical nature of the strength of“brittle”MG,implying the great opportunity for using high-strength brittle MGs in devices with small dimensions.

Effects of Nb Content on Yield Strength of NiTiNb Alloys in Martensite State

Two near single-phase NiTiNb alloys--NisoTi4sNb2 and Ni49.5Ti46.5Nb4-are prepared and studied by means of scanning electron microscopy （SEM）, energy dispersive spectroscopy （EDS）, differential scanning calorimetry （DSC） and tensile tests in order to unearth the effects of Nb-atom solid solution in NiTi phase on the yield strength induced by self-accommodation of martensite variants. The results show that the yield strength of near single-phase NiTiNb alloys varies inversely with the amount of Nb-atoms solid-dissolved in NiTi phase. From the results out of the prior and current studies, it can be surmised that the effects of Nb content on the yield strength of NiTiNb alloys in martensite state depend on the coaction. Nb solid solution weakening mechanism and β-Nb phase composite strengthening mechanism. This inference might be a satisfactory explanation to the fact that the yield strength of （NiTi）50-0.5xNbx alloys in martensite state begins with decline and then rises when the Nb content increases.

Influence of refined hierarchical martensitic microstructures on yield strength and impact toughness of ultra-high strength stainless steel

The hierarchical martensitic features in ultra-high strength stainless steel(UHSSS),including the prior austenite grains,martensite packets,blocks and laths with the descending size,were refined to various extents by employing different thermomechanical processes and then carefully characterized.Their relation to yield strength and impact toughness was analyzed.We conclude that the refinement of martensitic structures could lead to the significant increase of yield strength,which follows the Hall-Petch relation with the effect grain size defined by high angle boundaries(HABs).Impact toughness of UHSSS depends on the frequency and capability for retained austenite(RA)grains at both HABs and martensite lath boundaries to trap the propagating cracks via strain-induced transformation,in which the film-like RA grains at lath boundaries appear to make the greater contribution.

Effect of Crystallographic Texture on Anisotropy of Yield Strength in X100 Pipeline Steel

The anisotropy of microstructures and mechanical properties in commercial American Petroleum Institute （API） X100 pipeline steel was systematically investigated by experimental measurements. The experimental results show that anisotropy of yield strength could be observed considerably, which should be attributed to the crystallographic rex tures due to deformation and transformation of texture components. This is because the effect of the inhomogeneity of microstructure in different directions on the mechanical properties could be reasonably neglected based on the ex perimental investigation of grain size distribution. The effect of crystallographic texture on the anisotropy of yield strength was interpreted theoretically based on the relationship between yield strength and average orientation factor.