A New Elasticity and Finite Element Formulation for Different Young's Modulus When Tension and Compression Loadings

This paper presents a new elasticity and finite element formulation for different Young's modulus when tension and compression loadings in anisotropy media. The case studies, such as anisotropy and isotropy, were investigated. A numerical example was shown to find out the changes of neutral axis at the pure bending beams.

NANOINDENTATION OF THIN-FILM-SUBSTRATE SYSTEM DETERMINATION OF FILM HARDNESS AND YOUNG'S MODULUS

In the present paper,the hardness and Young's modulus of film-substrate systems are determined by means of nanoindentation experiments and modified models.Aluminum film and two kinds of substrates,i.e.glass and silicon,are studied.Nanoindentation XP Ⅱ and continuous stiffness mode are used during the experiments.In order to avoid the influence of the Oliver and Pharr method used in the experiments,the experiment data are analyzed with the constant Young's modulus assumption and the equal hardness assumption.The volume fraction model(CZ model)proposed by Fabes et al.(1992)is used and modified to analyze the measured hardness.The method proposed by Doerner and Nix(DN formula)(1986)is modified to analyze the measured Young's modulus.Two kinds of modified empirical formula are used to predict the present experiment results and those in the literature,which include the results of two kinds of systems,i.e.,a soft film on a hard substrate and a hard film on a soft substrate.In the modified CZ model,the indentation influence angle,(?), is considered as a relevant physical parameter,which embodies the effects of the indenter tip radius, pile-up or sink-in phenomena and deformation of film and substrate.

EFFECT OF DISPERSION OF MICA IN MATRIX ON YOUNG'S MODULUS OF MICA FILLED POLYETHYLENE

The correlation between Young's modulus of mica-filled high density polyethylene (HDPE), low density polyethylene(LDPE) and the state of dispersion of plasma-treated mica in the polymer matrices was studied. The modulus and the number average diameter of mica aggregates in matrix were determined with tensile testing and image analysis respectively. The interface structure of the filler/matrix and the bulk structure of matrix were examined through the dielectric spectrometry, differential scanning calorimetry (DSC) and dynamic viscoelastic spectrometry. The results show that the Young's modulus of the filial polyethylene depends to a great extent upon the state of dispersion of filler in matrix, but it is independent of the interface structure and bulk structure. The better the dispersion, the higher the Young's modulus.

Anomalies in Young's modulus behavior after annealing in polycrystalline SmS

In this paper,the dependencies of Young's modulus and attenuation decrement on samarium sulfide polycrystals(SmS)under various annealing temperatures are studied by the piezoelectric ultrasonic composite oscillator technique at a frequency of 100 kHz in the temperature range of 80-300 K.A decrease in Young's modulus with an increase of the annealing temperature due to the texturing of the material was revealed.At the same time,attenuation peaks were observed at temperatures about 90 and 125 K,presumably due to Niblett-Wilks and Bordoni relaxations.

A method to determine Young's modulus of soft gels for cell adhesion

A convenient technique is reported in this note for measuring elastic modulus of extremely soft material for cellular adhesion. Specimens of bending cylinder under gravity are used to avoid contact problem between testing device and sample, and a beam model is presented for evaluating the curvatures of gel beams with large elastic deformation. A self-adaptive algorithm is also proposed to search for the best estimation of gels＇ elastic moduli by comparing the experimental bending curvatures with those computed from the beam model with preestimated moduli. Application to the measurement of the property of polyacrylamide gels indi- cates that the material compliance varies with the concentrations of bis-acrylamide, and the gels become softer after being immersed in a culture medium for a period of time, no matter to what extent they are polymerized.

CALCULATION OF THE YOUNG'S MODULUS OF AN ADSORBED POLYMER LAYER

Polymer layers adsorbed to a surface or in a confined environment often change their mechanical properties. There is even the possibility of solidification of the confined layer. To judge the stiffness of such a layer, we used the Hertz model to calculate the Young＇s modulus of the polymer layer in the confinement of AFM experiments with silicon nitride tip with a radius of curvature ofR ≈ 50 nm and a glass sphere attached to the cantilever R =5 μm. Since there is no visible indentation of the layer in the AFM experiments, the layer is either penetrated very easily, or the indentation is too small to be seen in a force curve. The latter would be the case for a polymer layer with a Young＇s modulus above 4 × 10^8 Pa in case of an experiment with a silicon nitride tip and 4×10^5 Pa in case of a glass sphere.

The influence of defects on the effective Young's modulus of a defective solid

It is difficult to establish structure-property relationships in a defective solid because of its inhomogeneous-geometry microstructure caused by defects. In the present research, the effects of pores and cracks on the Young’s modulus of a defective solid are studied. Based on the law of the conservation of energy, mathematical formulations are proposed to indicate how the shape, size, and distribution of defects affect the effective Young’s modulus. In this approach, detailed equations are illustrated to represent the shape and size of defects on the effective Young’s modulus. Different from the results obtained from the traditional empirical analyses, mixture law or statistical method, for the first time, our results from the finite element method （FEM） and strict analytical calculation show that the influence of pore radius and crack length on the effective Young’s modulus can be quantified. It is found that the longest crack in a typical microstructure of ceramic coating dominates the contribution of the effective Young’s modulus in the vertical direction of the crack.

An improved model for predicting effective Young's modulus of the twisted structure under cyclic loading:taking into account the untwisting effect

Twist structures have diverse applications, ranging from dragline, electrical cable, and intelligent structure. Among these applications, tension deformation can＇t be avoided during the fabrication and working processes, which often leads to the twist structure rotation （called untwisting effect） and twist pitch increasing. As a consequence, this untwisting behavior has a large effect on the effective Young＇s modulus. In this paper, we present an improved model based on the classical Costello＇s theory to predict the effective Young＇s modulus of the basic structure, twisted by three same copper strands under cyclic loading. Series of experiments were carried out to verify the present model taking into account the untwisting effect. The experimental results have better agreements with the presented model than the common Costello＇s model.

Probing the effect of Young's modulus on the plugging performance of micro-nano-scale dispersed particle gels

The effect of mechanical strength of the dispersed particle gel(DPG)on its macro plugging performance is significant,however,little study has been reported.In this paper,DPG particles with different mechanical strengths were obtained by mechanical shearing of bulk gels prepared with different formula.Young’s moduli of DPG particles on the micro and nano scales were measured by atomic force microscope for the first time.The mapping relationship among the formula of bulk gel,the Young’s moduli of the DPG particles and the final plugging performance were established.The results showed that when the Young’s moduli of the DPG particles increased from 82 to 328 Pa,the plugging rate increased significantly from 91.46%to 97.10%due to the distinctly enhanced stacking density and strength at this range.While when the Young’s moduli of the DPG particles surpassed 328 Pa,the further increase of plugging rate with the Young’s moduli of the DPG particles became insignificant.These results indicated that the improvement of plugging rate was more efficient by adjusting the Young’s moduli of the DPG particles within certain ranges,providing guidance for improving the macroscopic application properties of DPG systems in reservoir heterogeneity regulation.

Young's double slit interference with vortex source

The fast and convenient demultiplex of optical vortex(OV) mode is crucial for its further application. We propose a novel approach that combines classic Young's doublet with an OV source to effectively identify the OV mode through the analysis of interference patterns. The interference patterns of the OV source incident on the double slits can be perfectly illustrated by using both the classical double-slit interference method and the Huygens–Fresnel principle. The interference fringes will twist along the negative or positive direction of x axis when topological charge(TC)l>0 or l<0, and the degree of the movement varies with the TC, allowing for a quantitative display of the OV characteristics through the interference patterns. Additionally, we deduce analytically that the zeroth-order interference fringe has a linear relationship with the TC and the vertical position. These findings highlight the ability to identify the OV mode by analyzing the interference patterns produced by Young's doublet.

A novel relationship between elastic modulus and void ratio associated with principal stress for coral calcareous sand

Elastic moduli,e.g.shear modulus G and bulk modulus K,are important parameters of geotechnical materials,which are not only the indices for the evaluation of the deformation ability of soils but also the important basic parameters for the development of the constitutive models of geotechnical materials.In this study,a series of triaxial loading-unloading-reloading shear tests and isotropic loading-unloadingreloading tests are conducted to study several typical mechanical properties of coral calcareous sand(CCS),and the void ratio evolution during loading,unloading and reloading.The test results show that the stress-strain curves during multiple unloading processes are almost parallel,and their slopes are much greater than the deformation modulus at the initial stage of loading.The relationship between the confining pressure and the volumetric strain can be defined approximately by a hyperbolic equation under the condition of monotonic loading of confining pressure.Under the condition of confining pressure unloading,the evolution of void ratio is linear in the e-lnp0 plane,and these lines are a series of almost parallel lines if there are multiple processes of unloading.Based on the experimental results,it is found that the modified Hardin formulae for the elastic modulus estimation have a significant deviation from the tested values for CCS.Based on the experimental results,it is proposed that the elastic modulus of soils should be determined by the intersection line of two spatial surfaces in the G/K-e-p’/pa space(pa:atmosphere pressure).“Ye formulation”is further proposed for the estimation of the elastic modulus of CCS.This new estimation formulation for soil elastic modulus would provide a new method to accurately describe the mechanical behavior of granular soils.

Enhanced asphalt dynamic modulus prediction: A detailed analysis of artificial hummingbird algorithm-optimised boosted trees

This study introduces and evaluates a novel artificial hummingbird algorithm-optimised boosted tree(AHAboosted)model for predicting the dynamic modulus(E*)of hot mix asphalt concrete.Using a substantial dataset from NCHRP Report-547,the model was trained and rigorously tested.Performance metrics,specifically RMSE,MAE,and R2,were employed to assess the model's predictive accuracy,robustness,and generalisability.When benchmarked against well-established models like support vector machines(SVM)and gaussian process regression(GPR),the AHA-boosted model demonstrated enhanced performance.It achieved R2 values of 0.997 in training and 0.974 in testing,using the traditional Witczak NCHRP 1-40D model inputs.Incorporating features such as test temperature,frequency,and asphalt content led to a 1.23%increase in the test R2,signifying an improvement in the model's accuracy.The study also explored feature importance and sensitivity through SHAP and permutation importance plots,highlighting binder complex modulus|G*|as a key predictor.Although the AHA-boosted model shows promise,a slight decrease in R2 from training to testing indicates a need for further validation.Overall,this study confirms the AHA-boosted model as a highly accurate and robust tool for predicting the dynamic modulus of hot mix asphalt concrete,making it a valuable asset for pavement engineering.

Modelling of the variation of granular base materials resilient modulus with material characteristics and humidity conditions

This study aims to quantify the susceptibility of granular materials used in pavements to changes in moisture content and propose a correlation model to incorporate this susceptibility into seasonal analyses.The fines content and the percentage of fractured coarse aggregates were identified as direct indicators of the resilient modulus susceptibility to changes in water content.The results showed that the percentage of fractured coarse aggregates particles(FR)has a more significant impact on the resilient modulus(Er)of crushed granular materials used in pavement construction than the combined indicator of the fines content and sample volumetrics(nf).Crushed granular materials with a higher percentage of fractured coarse aggregates are relatively insensitive to changes in the degree of saturation,but become more sensitive as the fine fraction porosity decreases.An adjusted model was proposed based on the existing formulation,but considers a complex parameter to describe and adjust the sensitivity of base granular materials to variations in moisture content with respect to fabrication charac-teristics,fines content and volumetric properties.The model shows that the variation of Er values is below10%for fully crushed granular materials.However,it reaches approximately±12%for materials with 75%of crushed coarse aggregates andþ40%and-25%for materials with FR=50%.This model could help select good ag-gregates characteristics and adjust grain-size distribution for environments where significant moisture content variations can occur in the pavement system,such as in the Province of Quebec(Canada).As it is based on pa-rameters that can be easily determined or estimated,it also represents a valuable tool for detailed design and analysis that can consider material characteristics.

A novel strategy for developingα+βdual-phase titanium alloys with low Young's modulus and high yield strength

In this study,a novel strategy for developingα+βdual-phase titanium alloys with low Young's modulus and high yield strength was proposed,and a Ti-15Nb-5Zr-4Sn-1 Fe alloy was developed through theoretical composition design and microstructure manipulation.After hot-rolling and subsequent annealing,a high volume fraction of ultrafine grainedαphase embedded in metastableβ-matrix was formed in the microstructure as intended.Consequently,this alloy exhibits both low Young's modulus(61 GPa)and high yield strength(912 MPa).The experimental results prove that the proposed strategy is appropriate for developing titanium alloys with superior yield strength-to-modulus ratio than those of conventional metallic biomedical materials.Present study might shed light on the research and development of advanced biomedical titanium alloys with low Young's modulus and high yield strength.

A Gradient Model for Young's Modulus and Surface Electrode Resistance of Ionic Polymer-Metai Composite

A new model is proposed to estimate Young's modulus and surface electrode resistance of the ionic polymer-metai composite(IPMC)with a gradient distribution of micros true ture.The entire IPMC electrode is divided into two parts,i.e.,the porous metal electrode and the gradient polymer-metai composite electrode,according to the geometrie properties of the electroless plated metal electrode.The validity and accuracy of the model are justified by comparing with the experimental observations of IPMC samples.The differences between model predictions and experimental data of Young's modulus and surface resistance of IPMC samples are+6.8%and-5.5%,respectively,indicating a reasonably good agreement.

Experimental study on crushing strength and Young's modulus of granules in iron ore sintering using Taguchi method

The contributions of three operating parameters(moisture content,hydrated lime addition,magnetite concentrate substitution)to the crushing strength and Young's modulus of granules in each stage of iron ore sintering were studied by applying the Taguchi method.The results indicated that the strength properties of the iron ore granules were greatly affected by its structure,which is composed of inner nuclei and an outer adhering layer.The granules with a thick adhering layer showed a clear changing trend in strength with increasing temperature,whereas those with a thin adhering layer showed additional fluctuations as their force-displacement responses were greatly determined by the nuclei.The granules with a thick adhering layer were gen erally more deformable and easier to break than that those with the thin adhering layer in most states.The signal-to-noise ratio and variance analysis indicated that moisture was the dominant parameter affecting the strength properties of the iron ore granules,as this factor controls the primary granule structure and material distribution.With the progress of sintering,the contribution of moisture to the quality characteristics gradually decreased(from〜80%to 50%),whereas the contributions of hydrated lime and magnetite concentrate increased correspondingly(from〜5%to 20%).

Determination of Young's modulus by nanoindentation

A methodology for determining Youngs modulus of materials by non-ideally sharp indentation has been developed. According to the principle of the same area-to-depth ratio, a non-ideally pyramidal indenter like a Berkovich one can be approximated by a non-ideally conical indenter with a spherical cap at the tip. By applying dimensional and finite element analysis to the non-ideally conical indentation, a set of approximate one-to-one relationships between the ratio of nominal hardness/reduced Youngs modulus and the ratio of elastic work/total work, which correspond to different tip bluntness, have been revealed. The nominal hardness is defined as the maximum indentation load divided by the cross-section area of the conical indenter specified at the maximum indentation depth. As a consequence, Youngs modulus can be determined from a nanoindentation test only using the maximum indentation load and depth, and the work done during loading and unloading processes. The new method for determining Youngs modulus is referred to as pure energy method. The validity of the method was examined by performing indentation tests on five materials. The experimental results and the standard reference values are in good agreement, indicating that the proposed pure energy method is a promising substitution for the most widely used analysis models at present.

Crystal orientation dependence of Young's modulus in Ti-Nb-based β-titanium alloy

The paper investigated the texture evolution of a biomedical β-titanium alloy (Ti-28Nb-13Zr-2Fe) under 15%-85% cold rolling reduction and 700°C-900°C recrystallization annealing treatment,and clarified the effects of crystal orientation on Young's modulus of the alloy.Orientation distribution function (ODF) maps and electron backscatter diffraction (EBSD) analysis revealed that the rolling texture type changed with the increase of reduction according to the sequence:α-fiber texture→γ-fiber texture→α-rotated cubic texture.Young's modulus exhibited the lowest value 54 GPa under 15% reduction.Strong {111}<112> γ-fiber texture was developed after rolling 85% reduction and annealing at 700°C,which was favorable to decreasing Young's modulus in comparison with randomly orientated microstructure.Cyclic loading-unloading tensile test proved that the gradual rotation of {110} slip plane during plastic deformation promoted the development of {001}<110> texture component,leading to the marked decrease of Young's modulus.

INFLUENCE OF YOUNG'S MODULUS ON DRAG-REDUCTION IN TURBULENT FLOW USING FLEXIBLE TUBES

In order to develop technologies of friction drag reduction with a flexible tube to be used for water transport, experimental studies were carried out on the influence of Young’s modulus on the turbulent drag reduction. The friction coefficients of flexible tubes with different Young’s modulus were examined by using a sleeve-tube structure. The fluctuating vibration of the outer wall and the fluctuating pressure on the inner wall of the tubes were measured with a laser displacement sensor and a pressure sensor. The results are as follows. The smaller the Young’s modulus of a flexible tube and the larger the Reynolds number, the larger the turbulent drag reduction rates become. The transition from laminar flow to turbulent flow can be delayed with an appropriate Young’s modulus. Non-dimensional amplitude of fluctuating vibration on the outer wall is smaller than that of a viscous sub-layer thickness, and is positively correlated with the friction drag reduction.

Size effects of effective Young's modulus for periodic cellular materials

With the wide demands of cellular materials applications in aerospace and civil engineering,research effort sacrificed for this type of materials attains nowadays a higher level than ever before.This paper is focused on the prediction methods of effective Young's modulus for periodical cellular materials.Based on comprehensive studies of the existing homogenization method(HM),the G-A meso-mechanics method(G-A MMM) and the stretching energy method(SEM) that are unable to reflect the size effect,we propose the bending energy method(BEM) for the first time,and a comparative study of these four methods is further made to show the generality and the capability of capturing the size effect of the BEM method.Meanwhile,the underlying characteristics of each method and their relations are clarified.To do this,the detailed finite element computing and existing experimental results of hexagonal honeycombs from the literature are adopted as the standard of comparison for the above four methods.Stretch and bending models of periodical cellular materials are taken into account,respectively for the comparison of stretch and flexural displacements resulting from the above methods.We conclude that the BEM has the strong ability of both predicting the effective Young's modulus and revealing the size effect.Such a method is also able to predict well the variations of structural displacements in terms of the cell size under stretching and bending loads including the non-monotonous variations for the hexagonal cell.On the contrary,other three methods can only predict the limited results whenever the cell size tends to be infinitely small.