Young's double slit interference with vortex source

The fast and convenient demultiplex of optical vortex(OV) mode is crucial for its further application. We propose a novel approach that combines classic Young's doublet with an OV source to effectively identify the OV mode through the analysis of interference patterns. The interference patterns of the OV source incident on the double slits can be perfectly illustrated by using both the classical double-slit interference method and the Huygens–Fresnel principle. The interference fringes will twist along the negative or positive direction of x axis when topological charge(TC)l>0 or l<0, and the degree of the movement varies with the TC, allowing for a quantitative display of the OV characteristics through the interference patterns. Additionally, we deduce analytically that the zeroth-order interference fringe has a linear relationship with the TC and the vertical position. These findings highlight the ability to identify the OV mode by analyzing the interference patterns produced by Young's doublet.

A novel relationship between elastic modulus and void ratio associated with principal stress for coral calcareous sand

Elastic moduli,e.g.shear modulus G and bulk modulus K,are important parameters of geotechnical materials,which are not only the indices for the evaluation of the deformation ability of soils but also the important basic parameters for the development of the constitutive models of geotechnical materials.In this study,a series of triaxial loading-unloading-reloading shear tests and isotropic loading-unloadingreloading tests are conducted to study several typical mechanical properties of coral calcareous sand(CCS),and the void ratio evolution during loading,unloading and reloading.The test results show that the stress-strain curves during multiple unloading processes are almost parallel,and their slopes are much greater than the deformation modulus at the initial stage of loading.The relationship between the confining pressure and the volumetric strain can be defined approximately by a hyperbolic equation under the condition of monotonic loading of confining pressure.Under the condition of confining pressure unloading,the evolution of void ratio is linear in the e-lnp0 plane,and these lines are a series of almost parallel lines if there are multiple processes of unloading.Based on the experimental results,it is found that the modified Hardin formulae for the elastic modulus estimation have a significant deviation from the tested values for CCS.Based on the experimental results,it is proposed that the elastic modulus of soils should be determined by the intersection line of two spatial surfaces in the G/K-e-p’/pa space(pa:atmosphere pressure).“Ye formulation”is further proposed for the estimation of the elastic modulus of CCS.This new estimation formulation for soil elastic modulus would provide a new method to accurately describe the mechanical behavior of granular soils.

Enhanced asphalt dynamic modulus prediction: A detailed analysis of artificial hummingbird algorithm-optimised boosted trees

This study introduces and evaluates a novel artificial hummingbird algorithm-optimised boosted tree(AHAboosted)model for predicting the dynamic modulus(E*)of hot mix asphalt concrete.Using a substantial dataset from NCHRP Report-547,the model was trained and rigorously tested.Performance metrics,specifically RMSE,MAE,and R2,were employed to assess the model's predictive accuracy,robustness,and generalisability.When benchmarked against well-established models like support vector machines(SVM)and gaussian process regression(GPR),the AHA-boosted model demonstrated enhanced performance.It achieved R2 values of 0.997 in training and 0.974 in testing,using the traditional Witczak NCHRP 1-40D model inputs.Incorporating features such as test temperature,frequency,and asphalt content led to a 1.23%increase in the test R2,signifying an improvement in the model's accuracy.The study also explored feature importance and sensitivity through SHAP and permutation importance plots,highlighting binder complex modulus|G*|as a key predictor.Although the AHA-boosted model shows promise,a slight decrease in R2 from training to testing indicates a need for further validation.Overall,this study confirms the AHA-boosted model as a highly accurate and robust tool for predicting the dynamic modulus of hot mix asphalt concrete,making it a valuable asset for pavement engineering.

Modelling of the variation of granular base materials resilient modulus with material characteristics and humidity conditions

This study aims to quantify the susceptibility of granular materials used in pavements to changes in moisture content and propose a correlation model to incorporate this susceptibility into seasonal analyses.The fines content and the percentage of fractured coarse aggregates were identified as direct indicators of the resilient modulus susceptibility to changes in water content.The results showed that the percentage of fractured coarse aggregates particles(FR)has a more significant impact on the resilient modulus(Er)of crushed granular materials used in pavement construction than the combined indicator of the fines content and sample volumetrics(nf).Crushed granular materials with a higher percentage of fractured coarse aggregates are relatively insensitive to changes in the degree of saturation,but become more sensitive as the fine fraction porosity decreases.An adjusted model was proposed based on the existing formulation,but considers a complex parameter to describe and adjust the sensitivity of base granular materials to variations in moisture content with respect to fabrication charac-teristics,fines content and volumetric properties.The model shows that the variation of Er values is below10%for fully crushed granular materials.However,it reaches approximately±12%for materials with 75%of crushed coarse aggregates andþ40%and-25%for materials with FR=50%.This model could help select good ag-gregates characteristics and adjust grain-size distribution for environments where significant moisture content variations can occur in the pavement system,such as in the Province of Quebec(Canada).As it is based on pa-rameters that can be easily determined or estimated,it also represents a valuable tool for detailed design and analysis that can consider material characteristics.

一类Stancu型的Szász-Mirakjan-Durrmeyer算子的逼近性质研究

该文介绍了一类Stancu型的Szász-Mirakjan-Durrmeyer算子,计算了该算子的一阶到四阶矩.然后用连续模和K-泛函等工具,讨论了该算子的逼近性质,还研究了算子对Lipschitz函数类的估计.最后建立了该算子的Voronvskaya型渐近展开式.所得定理扩展了Aslan(2022)的结果.

A New Elasticity and Finite Element Formulation for Different Young's Modulus When Tension and Compression Loadings

This paper presents a new elasticity and finite element formulation for different Young's modulus when tension and compression loadings in anisotropy media. The case studies, such as anisotropy and isotropy, were investigated. A numerical example was shown to find out the changes of neutral axis at the pure bending beams.

NANOINDENTATION OF THIN-FILM-SUBSTRATE SYSTEM DETERMINATION OF FILM HARDNESS AND YOUNG'S MODULUS

In the present paper,the hardness and Young's modulus of film-substrate systems are determined by means of nanoindentation experiments and modified models.Aluminum film and two kinds of substrates,i.e.glass and silicon,are studied.Nanoindentation XP Ⅱ and continuous stiffness mode are used during the experiments.In order to avoid the influence of the Oliver and Pharr method used in the experiments,the experiment data are analyzed with the constant Young's modulus assumption and the equal hardness assumption.The volume fraction model(CZ model)proposed by Fabes et al.(1992)is used and modified to analyze the measured hardness.The method proposed by Doerner and Nix(DN formula)(1986)is modified to analyze the measured Young's modulus.Two kinds of modified empirical formula are used to predict the present experiment results and those in the literature,which include the results of two kinds of systems,i.e.,a soft film on a hard substrate and a hard film on a soft substrate.In the modified CZ model,the indentation influence angle,(?), is considered as a relevant physical parameter,which embodies the effects of the indenter tip radius, pile-up or sink-in phenomena and deformation of film and substrate.

A method to determine Young's modulus of soft gels for cell adhesion

A convenient technique is reported in this note for measuring elastic modulus of extremely soft material for cellular adhesion. Specimens of bending cylinder under gravity are used to avoid contact problem between testing device and sample, and a beam model is presented for evaluating the curvatures of gel beams with large elastic deformation. A self-adaptive algorithm is also proposed to search for the best estimation of gels＇ elastic moduli by comparing the experimental bending curvatures with those computed from the beam model with preestimated moduli. Application to the measurement of the property of polyacrylamide gels indi- cates that the material compliance varies with the concentrations of bis-acrylamide, and the gels become softer after being immersed in a culture medium for a period of time, no matter to what extent they are polymerized.

Improving the Young’s modulus of Mg via alloying and compositing–A short review

Lightweight,high-modulus structural materials are highly desired in many applications like aerospace,automobile and biomedical instruments.As the lightest metallic structural material,magnesium(Mg)has great potential but is limited by its low intrinsic Young’s modulus.This paper reviews the investigations on high-modulus Mg-based materials during the last decades.The nature of elastic modulus is introduced,and typical high-modulus Mg alloys and Mg matrix composites are reviewed.Specifically,Mg alloys enhance Young’s modulus of pure Mg mainly by introducing suitable alloying elements to promote the precipitation of high-modulus second phases in the alloy system.Differently,Mg matrix composites improve Young’s modulus by incorporating high-modulus particles,whiskers and fibers into the Mg matrix.The modulus strengthening effectiveness brought by the two approaches is compared,and Mg matrix composites stand out as a more promising solution.In addition,two well-accepted modulus prediction models(Halpin-Tsai and Rule of mixtures(ROM))for different Mg matrix composites are reviewed.The effects of reinforcement type,size,volume fraction and interfacial bonding condition on the modulus of Mg matrix composites are discussed.Finally,the existing challenges and development trends of high-modulus Mg-based materials are proposed and prospected.

Experimental Study on Young′s Modulus of Concrete

Young′s Modulus of concrete is studied on the basis of triaxial compressive experiments. The authors proposed two empirical equations to calculate its static Young′s modulus and dynamic Young′s modulus when dynamic Poisson ratio μ d varies nearby 0.20.P wave velocity and elastic modulus have the same varying tendency as letter N. μ,μ d decrease with the increase of loading rate and μ d has a great effect on the parameters E d and E D.

Photoacoustic elastography based on laser-excited shear wave

Elastography can be used as a diagnostic method for quantitative characterization of tissue hardness information and thus,differential changes in pathophysiological states of tissues.In this study,we propose a new method for shear wave elastography(SWE)based on laser-excited shear wave,called photoacoustic shear wave elastography(PASWE),which combines photoacoustic(PA)technology with ultrafast ultrasound imaging.By using a focused laser to excite shear waves and ultrafast ultrasonic imaging for detection,high-frequency excitation of shear waves and noncontact elastic imaging can be realized.The laser can stimulate the tissue with the light absorption characteristic to produce the thermal expansion,thus producing the shear wave.The frequency of shear wave induced by laser is higher and the frequency band is wider.By tracking the propagation of shear wave,Young’s modulus of tissue is reconstructed in the whole shear wave propagation region to further evaluate the elastic information of tissue.The feasibility of the method is verified by experiments.Compared with the experimental results of supersonic shear imaging(SSI),it is proved that the method can be used for quantitative elastic imaging of the phantoms.In addition,compared with the SSI method,this method can realize the noncontact excitation of the shear wave,and the frequency of the shear wave excited by the laser is higher than that of the acoustic radiation force(ARF),so the spatial resolution is higher.Compared to the traditional PA elastic imaging method,this method can obtain a larger imaging depth under the premise of ensuring the imaging resolution,and it has potential application value in the clinical diagnosis of diseases requiring noncontact quantitative elasticity.

CALCULATION OF THE YOUNG'S MODULUS OF AN ADSORBED POLYMER LAYER

Polymer layers adsorbed to a surface or in a confined environment often change their mechanical properties. There is even the possibility of solidification of the confined layer. To judge the stiffness of such a layer, we used the Hertz model to calculate the Young＇s modulus of the polymer layer in the confinement of AFM experiments with silicon nitride tip with a radius of curvature ofR ≈ 50 nm and a glass sphere attached to the cantilever R =5 μm. Since there is no visible indentation of the layer in the AFM experiments, the layer is either penetrated very easily, or the indentation is too small to be seen in a force curve. The latter would be the case for a polymer layer with a Young＇s modulus above 4 × 10^8 Pa in case of an experiment with a silicon nitride tip and 4×10^5 Pa in case of a glass sphere.

一种采用柔性缓冲垫块的双面散热SiC MOSFET双向开关模块研究

随着功率模块朝着高温、高功率、高密度方向发展,这对模块的封装结构提出了新的要求。较传统的引线键合结构,双面散热结构由于具有高散热能力和低寄生电感等特点受到广泛关注。但是双面散热结构材料间热膨胀系数的差异使之承受较大的热-机械应力,降低了功率模块的可靠性。因此,为设计具有低热-机械应力双面散热双向开关,本研究首先使用仿真分析了芯片布局对模块散热性能以及寄生电感的影响,在此基础上提出了一种具有低杨氏模量的柔性缓冲垫块,综合仿真及试验初步证明其降低热-机械应力、提高模块可靠性的可行性。

Prediction and optimization of process variables to maximize the Young’s modulus of plasma sprayed alumina coatings on AZ31B magnesium alloy

Like other manufacturing techniques,plasma spraying has also a non-linear behavior because of the contribution of many coating variables.This characteristic results in finding optimal factor combination difficult.Subsequently,the issue can be solved through effective and strategic statistical procedures integrated with systematic experimental data.Plasma spray parameters such as power,stand-off distance and powder feed rate have significant influence on coating characteristics like Young’s modulus.This paper presents the use of statistical techniques in specifically response surface methodology(RSM),analysis of variance,and regression analysis to develop empirical relationship to predict Young’s modulus of plasma-sprayed alumina coatings.The developed empirical relationships can be effectively used to predict Young’s modulus of plasma-sprayed alumina coatings at 95%confidence level.Response graphs and contour plots were constructed to identify the optimum plasma spray parameters to attain maximum Young’s modulus in alumina coatings.A linear regression relationship was established between porosity and Young’s modulus of the alumina coatings.

Determination of reduced Young s modulus of thin films using indentation test

The flat cylindrical indentation tests with different sizes of punch radius were investigated using finite element method （FEM） aimed to reveal the effect of punch size on the indentation behavior of the film/substrate system. Based on the FEM results analysis, two methods was proposed to separate film＇s reduced Young＇s modulus from a film/substrate system. The first method was based on a new weight function that quantifies film＇s and substrate＇s contributions to the overall mechanical properties of the film/substrate system in the flat cylindrical indentation test. The second method, a numerical approach, including fitting and extrapolation procedures was put forward. Both of the results from the two methods showed a reasonable agreement with the one input FE model. At last, the effect of maximum indentation depth and the surface micro-roughness of the thin film on the reduced Young＇s modulus of the film/substrate system were discussed. The methods proposed in the present study provide some new conceptions on evaluating other properties of thin films, e.g. creep, for which a flat-ended punch is also employed.

Analysis of the elastic-plastic indentation properties of materials with varying ratio of hardness to Young’s modulus

The elastic-plastic indentation properties of materials with varying ratio of hardness to Young’s modulus(H/E) were analyzed with the finite element method. And the indentation stress fields of materials with varying ratio H/E on the surface were studied by the experiment. The results show that the penetration depth, contact radius, plastic pile-up and the degree of elastic recovery depend strongly on the ratio H/E. Moreover, graphs were established to describe the relationship between the elastic-plastic indentation parameters and H/E. The established graphs can be used to predict the H/E of materials when compared with experimental data.

Macroscopic Young’s Elastic Modulus Model of Particle Packing Rock Layers

Based on the Hertzian granular contact mechanics model, the paper built up a Macroscopic Young’s Elastic Modulus of particle/granular packing rock layers, and built up a ties to connecting Young’s Elastic Modulus of sand particle in Meso and the Macroscopic Young’s Modulus of granular packing rock layers. The Macroscopic Young’s Modulus of granular packing rock layers is far less than the Young’s Modulus of sand particle. The Macroscopic Young’s Modulus of granular packing rock layers is proportioned to the powers of 1/3 of the vertical contact force of sand particles. The Macroscopic Young’s Modulus is inversely proportional to particle diameter. The paper calculated the vertical contact force of five types aligning mode of the particles. When equal stress, the increased of the coordination number lead to the decrease of the contact force fn, this lead to the coordination number is an inverse proportion to Macroscopic Young’s Modulus. But the larger coordination number change only means very little Macroscopic Young’s Modulus change.

EFFECT OF DISPERSION OF MICA IN MATRIX ON YOUNG'S MODULUS OF MICA FILLED POLYETHYLENE

The correlation between Young's modulus of mica-filled high density polyethylene (HDPE), low density polyethylene(LDPE) and the state of dispersion of plasma-treated mica in the polymer matrices was studied. The modulus and the number average diameter of mica aggregates in matrix were determined with tensile testing and image analysis respectively. The interface structure of the filler/matrix and the bulk structure of matrix were examined through the dielectric spectrometry, differential scanning calorimetry (DSC) and dynamic viscoelastic spectrometry. The results show that the Young's modulus of the filial polyethylene depends to a great extent upon the state of dispersion of filler in matrix, but it is independent of the interface structure and bulk structure. The better the dispersion, the higher the Young's modulus.

Anomalies in Young's modulus behavior after annealing in polycrystalline SmS

In this paper,the dependencies of Young's modulus and attenuation decrement on samarium sulfide polycrystals(SmS)under various annealing temperatures are studied by the piezoelectric ultrasonic composite oscillator technique at a frequency of 100 kHz in the temperature range of 80-300 K.A decrease in Young's modulus with an increase of the annealing temperature due to the texturing of the material was revealed.At the same time,attenuation peaks were observed at temperatures about 90 and 125 K,presumably due to Niblett-Wilks and Bordoni relaxations.

Integrated Computational Materials Engineering for the Development and Design of High Modulus Al Alloys

Integrated computational materials engineering(ICME)is to integrate multi-scale computational simulations and key experimental methods such as macroscopic,mesoscopic,and microscopic into the whole process of Al alloys design and development,which enables the design and development of Al alloys to upgrade from traditional empirical to the integration of compositionprocess-structure-mechanical property,thus greatly accelerating its development speed and reducing its development cost.This study combines calculation of phase diagram(CALPHAD),Finite element calculations,first principle calculations,and microstructure characterization methods to predict and regulate the formation and structure of composite precipitates from the design of highmodulus Al alloy compositions and optimize the casting process parameters to inhibit the formation of micropore defects in the casting process,and the final tensile strength of Al alloys reaches420 MPa and Young's modulus reaches more than 88 GPa,which achieves the design goal of the high strength and modulus Al alloys,and establishes a new mode of the design and development of the strength/modulus Al alloys.