A new PWM converter based on soft switching is introduced. The converter uses a minimum number of devices, and requires less switching operations than conventional techniques. Switching is realized solely in a ZVS (z...A new PWM converter based on soft switching is introduced. The converter uses a minimum number of devices, and requires less switching operations than conventional techniques. Switching is realized solely in a ZVS (zero voltage switching) mode, therefore the loss is reduced and EMI (electromagnetic interference) is suppressed. The paper analyzes the operation of ZVS, and discusses the methods for maintaining a unit power factor and constant DC voltage. Changing the modulation index M and the phase angle θ keeps the input current in phase with the voltage. It also keeps the current sinusoidal, and ensures a constant output voltage.展开更多
为了使开关电源达到高功率密度和易于便携的要求,采用高频PWM(Pulse Width Modulation)软开关控制方式,不但利于减小开关电源的体积,而且还能有效降低开关器件损耗和噪音。详细分析了零电压变换ZVS(Zero Voltage Switch)PWM脉宽调制Boos...为了使开关电源达到高功率密度和易于便携的要求,采用高频PWM(Pulse Width Modulation)软开关控制方式,不但利于减小开关电源的体积,而且还能有效降低开关器件损耗和噪音。详细分析了零电压变换ZVS(Zero Voltage Switch)PWM脉宽调制Boost变换器的软开关过程及实现软开关的条件,利用Saber软件对Boost电路在硬、软开关条件下进行了仿真验证。仿真结果表明ZVS PWM软开关变换技术具有开关损耗小、恒频控制和变换效率高等优点。展开更多
The FB-ZVZCS-PWM converter is realized by the way of subjoiningblock-capacitor into the FB-ZVS-PWM converter. At the freewheeling interval, the primary current isattenuated fast to zero and maintained. And then, power...The FB-ZVZCS-PWM converter is realized by the way of subjoiningblock-capacitor into the FB-ZVS-PWM converter. At the freewheeling interval, the primary current isattenuated fast to zero and maintained. And then, power device of the static leg becomes azero-current-switch (ZCS), power device of the shifted leg becomes a zero-voltage-switch(ZVS). Thus,on one hand IGBT (Insulated gate bipolar transistor) with tail current can be easily used infull-bridge soft-switching converter; on the other hand additional circuiting energy is greatlyreduced. At the same time, less duty cycle loss, lower secondary parasitic resonance, widersoft-switching load range can be achieved. Based on the existing component models in the Pspicesoftware package, a combined model of IGBT is established, in which a non-linear capacitor isintroduced to replace the parasitic capacitor. Using this model, computerized simulation isconducted for the FB-ZVZCS-PWM soft-switching converter, the switching and energy-transferringcharacteristics of the power device are analyzed. Finally, based on the achievement above, a 10 kWarc welding inverter with FB-ZVZCS-PWM converter is developed. The simulation results are testifiedby experiments. It is proved that by adopting appropriate models, computerized simulation is aneffective and useful tool for the development of the arc welding inverter.展开更多
This paper proposes the design and experimentation of digital control of soft-switched interleaved boost converter using FPGA for Telecommunication System. The switching devices in the proposed converter are turned on...This paper proposes the design and experimentation of digital control of soft-switched interleaved boost converter using FPGA for Telecommunication System. The switching devices in the proposed converter are turned on and off with Zero Voltage Switching (ZVS) and Zero Current Switching (ZCS) respectively. The circuit is operated in Continuous Conduction Mode (CCM) with various load ranges having duty cycle of more than 50%. The proposed converter is studied by developing the simulation module in MATLAB/SIMULINK. A PI controller is designed and implemented in FPGA to obtain a regulated DC output for line and load variations. Simulation and experimentation results are verified with a prototype development of the proposed converter. The results indicate that the converter performance is enhanced with closed loop control.展开更多
文摘A new PWM converter based on soft switching is introduced. The converter uses a minimum number of devices, and requires less switching operations than conventional techniques. Switching is realized solely in a ZVS (zero voltage switching) mode, therefore the loss is reduced and EMI (electromagnetic interference) is suppressed. The paper analyzes the operation of ZVS, and discusses the methods for maintaining a unit power factor and constant DC voltage. Changing the modulation index M and the phase angle θ keeps the input current in phase with the voltage. It also keeps the current sinusoidal, and ensures a constant output voltage.
基金This project is supported by National Natural Science Foundation of China(No.50075003)Municipal Natural Science Foundation of Beijing, China(No.3001001).
文摘The FB-ZVZCS-PWM converter is realized by the way of subjoiningblock-capacitor into the FB-ZVS-PWM converter. At the freewheeling interval, the primary current isattenuated fast to zero and maintained. And then, power device of the static leg becomes azero-current-switch (ZCS), power device of the shifted leg becomes a zero-voltage-switch(ZVS). Thus,on one hand IGBT (Insulated gate bipolar transistor) with tail current can be easily used infull-bridge soft-switching converter; on the other hand additional circuiting energy is greatlyreduced. At the same time, less duty cycle loss, lower secondary parasitic resonance, widersoft-switching load range can be achieved. Based on the existing component models in the Pspicesoftware package, a combined model of IGBT is established, in which a non-linear capacitor isintroduced to replace the parasitic capacitor. Using this model, computerized simulation isconducted for the FB-ZVZCS-PWM soft-switching converter, the switching and energy-transferringcharacteristics of the power device are analyzed. Finally, based on the achievement above, a 10 kWarc welding inverter with FB-ZVZCS-PWM converter is developed. The simulation results are testifiedby experiments. It is proved that by adopting appropriate models, computerized simulation is aneffective and useful tool for the development of the arc welding inverter.
文摘This paper proposes the design and experimentation of digital control of soft-switched interleaved boost converter using FPGA for Telecommunication System. The switching devices in the proposed converter are turned on and off with Zero Voltage Switching (ZVS) and Zero Current Switching (ZCS) respectively. The circuit is operated in Continuous Conduction Mode (CCM) with various load ranges having duty cycle of more than 50%. The proposed converter is studied by developing the simulation module in MATLAB/SIMULINK. A PI controller is designed and implemented in FPGA to obtain a regulated DC output for line and load variations. Simulation and experimentation results are verified with a prototype development of the proposed converter. The results indicate that the converter performance is enhanced with closed loop control.
