Removal of Organochlorine from Model Oil Using Mg-Modified ZSM-5 Zeolite:Dechlorination Performance,Regeneration,and Thermodynamics

Various metal-modified ZSM-5 zeolite adsorbents prepared by the impregnation method were applied to the removal of organic chlorides from model naphtha.The adsorption performance and regeneration stability were investigated by static adsorption experiments.The morphologies,structural features,and physicochemical properties of the adsorbents were characterized by X-ray diffraction,Brunauer-Emmett-Teller analysis,NH3 temperature-programmed desorption,scanning electron microscopy,transmission electron microscopy,and pyridine adsorption infrared spectroscopy.The Mg/ZSM-5 zeolite adsorbent possessed a relatively high specific surface area and good metal dispersion and exhibited the best dechlorination and regeneration performance.The characterization results revealed that introduction of the metal exerted a significant influence on the acidic properties of the catalyst surface.A decrease in the ratio of Brønsted acidic sites to Lewis acidic sites and an increase in the amount of moderately acidic sites were confirmed to be responsible for the excellent adsorption performance of the Mg-modified ZSM-5 zeolite.Furthermore,the Langmuir adsorption isotherm model was applied to study the adsorption equilibrium and thermodynamics of the Mg/ZSM-5 adsorbent under mild conditions.The results revealed that the removal of 1,2-dichloroethane by the Mg/ZSM-5 adsorbent was endothermic,spontaneous,disordered,and primarily involved physical adsorption.

Differences between Zn/HZSM-5 and Zn/HZSM-11 zeolite catalysts in alkylation of benzene with dimethyl ether

HZSM-11 zeolite supported Zn catalysts with different Zn contents （xZn/HZSM-11A） were prepared. In the alkylation of benzene with dimethyl ether （DME） in a fixed bed reactor, the catalyst with Zn content of 6 wt% （6Zn/HZSM-11A） showed appropriate performance. Focus was put on the comparison between 6Zn/HZSM-5 and 6Zn/HZSM-11 with the same crystal size of 600-800 nm, and also with the similar BET surface area, micropore volume, Si/Al2 molar ratio, and acidity. In the alkylation of benzene with DME, the 6Zn/HZSM-11 showed better activity and stability, and especially enhanced the conversion of benzene and selectivities to xylene and trimethylbenzene, compared with the 6Zn/HZSM-5. This was mainly related to the higher adsorption capacity and adsorption-desorption rates to the three adsorbates （benzene, m-xylene and 1,3,5-trimethylbenzene） over the 6Zn/HZSM-11 in comparison with the 6Zn/HZSM-5.

Synthesis and characterization of an unusual snowflake-shaped ZSM-5 zeolite with high catalytic performance in the methanol to olefin reaction

The ZSM-5 zeolite with an unusual snowflake-shaped morphology was hydrothermally synthesized for the first time,and compared with common ellipsoidal and boat-like shaped samples.These samples were characterized by N2 adsorption-desorption,X-ray fluorescence spectroscopy,scanning electron microscopy,X-ray diffraction,magic angle spinning nuclear magnetic resonance,temperature-programmed desorption of ammonia,and infrared spectroscopy of pyridine adsorption.The results suggest that the BET surface area and SiO2/Al2O3 ratio of these samples are similar,while the snowflake-shaped ZSM-5 zeolite possesses more of the（101） face,and distortion,dislocation,and asymmetry in the framework,resulting in a larger number of acid sites than the conventional samples.Catalysts for the methanol to olefin（MTO） reaction were prepared by loading Ca on the samples.The snowflake-shaped Ca/ZSM-5 zeolite exhibited excellent selectivity for total light olefin（72%） and propene（39%） in MTO.The catalytic performance influenced by the morphology can be mainly attributed to the snowflake-shaped ZSM-5 zeolite possessing distortion,dislocation,and asymmetry in the framework,and lower diffusion limitation than the conventional samples.

ZSM-11和ZSM-5分子筛孔道结构差异对其甲醇制烯烃催化性能的影响

本工作采用水热合成法制备了具有相似形貌、粒径、织构性质和酸性的ZSM-11和ZSM-5分子筛,借助多种表征技术研究了这两类分子筛的十元环孔道结构差异对其甲醇转化制烯烃(MTO)催化性能的影响。结果表明,由于ZSM-5的正弦孔道比ZSM-11的直孔道的扩散阻力大,反应中间体和产物分子在ZSM-5分子筛上的停留时间较长,强化了长链烯烃氢转移反应,导致生成更多的甲基苯物种,从而增强了芳烃循环的贡献;相比之下,ZSM-11分子筛的直孔道限制了长链烯烃的氢转移反应,减少了多甲基苯物种的产生,有利于提高烯烃循环的贡献。因此,与具有相似形貌、粒径、织构性质和酸性的ZSM-5-60分子筛相比,ZSM-11-60分子筛对MTO反应具有更长的催化寿命(98.3 h对比65.4h)和更高的丙烯选择性(34.6%对比27.4%)。这些结果深化了对分子筛MTO催化性能与其孔道结构关系的认识,有助于新型高效的甲醇转化分子筛催化剂的开发和反应过程的探索。

Synthesis and Characterization of ZSM-5/β Co-Crystalline Zeolite

ZSM-5/β co-crystalline zeolites with different content of ZSM-5 have beensynthesized by adding different amount of ZSM-5 to the synthetic system of β zeolite with NaAlO_2,silica sol as the source of aluminum and silica, respectively, and TEA^+ as the template undercontrolled condition of the synthesis. The ZSM-5/β co-crystalline zeolite was studied by XRD, SEM,BET and NH_3-TPD. The reaction activity of toluene alkylation was investigated with a mixture oftoluene-methanol as the feedstock in a pulse micro-reactor over the ZSM-5/β co-crystalline zeolite.It is found that ZSM-5/β co-crystalline zeolite has two kinds of zeolite structure including ZSM-5and β zeolite, not in the form of a physical mixture. The pore structure of ZSM-5/βco-crystalline zeolites is different from that for β zeolite, ZSM-5 and their physical mixture. Inaddition, the peaks of both high and low temperature desorption of ammonia over the ZSM-5/βco-crystalline zeolite shift 23℃ to lower temperatures and the acid amount of its strong acid is 3%more than the physical mixture. So the ZSM-5/β co-crystalline zeolite produces the highest contentof xylene, which is 10.4% higher than the physical mixture. And the ZSM-5/β co-crystalline zeolitehas better selectivity for toluene alkylation and weaker de-methylation than β zeolite, ZSM-5 andtheir physical mixture.

Alkali-metal-modified ZSM-5 zeolites for improvement of catalytic dehydration of lactic acid to acrylic acid

Various ZSM-5 zeolites modified with alkali metals （Li, Na, K, Rb, and Cs） were prepared using ion exchange. The catalysts were used to enhance the catalytic dehydration of lactic acid （LA） to acrylic acid （AA）. The effects of cationic species on the structures and surface acid-base distributions of the ZSM-5 zeolites were investigated. The important factors that affect the catalytic performance were also identified. The modified ZSM-5 catalysts were characterized using X-ray diffraction, tempera- ture-programmed desorptions of NH3 and CO2, pyridine adsorption spectroscopy, and N2 adsorption to determine the crystal phase structures, surface acidities and basicities, nature of acid sites, specific surface areas, and pore volumes. The results show that the acid-base sites that are adjusted by alkali-metal species, particularly weak acid-base sites, are mainly responsible for the formation of AA. The KZSM-5 catalyst, in particular, significantly improved LA conversion and AA selectivity because of the synergistic effect of weak acid-base sites. The reaction was conducted at different reaction temperatures and liquid hourly space velocities （LHSVs） to understand the catalyst selectivity for AA and trends in byproduct formation. Approximately 98% LA conversion and 77% AA selectivity were achieved using the KZSM-5 catalyst under the optimum conditions （40 wt% LA aqueous solution, 365 ℃, and LHSV 2 h-1）.

Disproportionation of Toluene by Modified ZSM-5 Zeolite Catalysts with High Shape-selectivity Prepared Using Chemical Liquid Deposition with Tetraethyl Orthosilicate

Shape-selective catalysts for the disproportionation of toluene were prepared by the modification of the cylinder-shaped ZSM-5 zeolite extrudates with chemical liquid deposition with TEOS （tetraethyl orthosilicate）.Various parameters for preparing catalysts were changed to investigate the suitable conditions.The resulting cata-lysts were tested in a pressured fixed bed reactor and characterized by SEM （scanning electron microscopy）.The conversion of toluene and para-xylene selectivity were influenced remarkably by the n（SiO2）/n（Al2O3） ratio of ZSM-5 zeolite,the type and amount of deposition agent,acid and solvent used,and the time and cycle of deposition treatment.TEOS was proved to be a more efficient agent than the conventional polysiloxanes when the deposition amount was low.The catalyst prepared at the suitable conditions exhibited a high para-xylene selectivity of 91.1% with considerable high conversion of 25.6%.SEM analyses confirmed the formation of a layer of amorphous silica on the external surface of ZSM-5 zeolie crystals,which was responsible for the highly enhanced shape-selectivity.

Aromatization over nanosized Ga-containing ZSM-5 zeolites prepared by different methods:Effect of acidity of active Ga species on the catalytic performance

Nanosized Ga-containing ZSM-5 zeolites were prepared via isomorphous substitution and impregnation followed by characterized using various techniques. The catalytic performance of the zeolites for the aromatization of 1-hexene was investigated. The results indicate that isomorphous substitution promotes the incorporation of Ga heteroatoms into the framework along with the formation of extra-framework GaO;species（[GaO;]a） that have stronger interactions with the negative potential of the framework. In addition, based on the Py-IR results and catalytic performance, the [GaO;]aspecies with stronger Lewis acid sites produced a better synergism with moderate Br?nsted acid sites and thus improved the selectivity to aromatic compounds. However, the impregnation results in the formation of Ga;O;phase and small amounts of GaO;species that are mainly located on the external surface（[GaO;];）, which contribute to weaker Lewis acid sites due to weaker interactions with the zeolite framework. During 1-hexene aromatization, the nanosized Ga isomorphously substituted ZSM-5 zeolite samples（Gax-NZ5） exhibited better catalytic performance compared to the impregnated samples, and the highest aromatic yield（i.e.,65.4 wt%） was achieved over the Ga4.2-NZ5 sample, which contained with the highest Ga content.

Thermal and hydrothermal stabilities of the alkali-treated HZSM-5 zeolites

HZSM-5 zeolites with the micro-mesopore hierarchical porosity have been prepared by the post-synthesis of alkali-treatment, and their thermal and hydrothermal stabilities were studied using DTA, XRD, and NH3-TPD characterization techniques. Compared to the unmodified zeolite, the thermal and hydrothermal stabilities of the alkali-treated ZSM-5 zeolites were slightly deteriorated because of the introduction of mesopores caused by the desilication. Nevertheless, the alkali-treated zeolite framework could be maintained until the temperature increased to 1175 ℃.

Experiment and Modeling of Pure and Binary Adsorption of n-Butane and Butene-1 on ZSM-5 Zeolites with Different Si/Al Ratios

Four ZSM-5 zeolite catalysts with different Si/Al ratios for the catalytic cracking of C4 fractions to produce ethylene and propylene were prepared in this study.First,the adsorption isotherms of pure n-butane and butene-1 and their mixtures on these catalysts at 300K and p=0—100kPa were measured using the intelligent gra- vimetric analyzer.The experimental results indicate that the presence of Al can significantly affect the adsorption of butene-1 than that of n-butane on ZSM-5 zeolites.Then,the double Langmuir(DL)model was applied to study the pure gas adsorption on ZSM-5 zeolites for pure n-butane and butene-1.By combining the DL model with the ideal adsorbed solution theory(IAST),the IAST-DL model was applied to model the butene-1(1)/n-butane(2)binary mixture adsorption on ZSM-5 zeolites with different Si/Al ratios.The calculated results are in good agreement with the experimental data,indicating that the IAST-DL model is effective for the present systems.Finally,the adsorp- tion over a wide range of variables was predicted at low pressure and 300K by the model proposed.It is found that the selectivity of butene-1 over n-butane increases linearly with the decrease of Si/Al ratio.A correlation between the selectivity and Si/Al ratio of the sample was proposed at 300K and p=0.08MPa.

Adsorption of Benzene and Propylene in Zeolite ZSM-5:Grand Canonical Monte Carlo Simulations

The adsorption behavior of benzene and propylene in zeolite ZSM-5 was studied by Grand Canonical Monte Carlo（GCMC） simulations. It could be found that benzene and propylene molecules showed different adsorption behavior in the zeolite cavities. The loadings of propylene were significantly larger than those of benzene at 100 kPa. From the figures of potential energy distribution, the potential energy of benzene/zeolite was more negative than that of propylene/zeolite, so benzene could be adsorbed more stably than propylene. When the temperature was in- creased from 298 to 443 K at 100 kPa, the loading ofpropylene was reduced from 99 to 82 molecules, whereas that of benzene changed little. When benzene and propylene were adsorbed in zeolite simultaneously, the competitive adsorption of them occurred; therefore, the potential energy distribution could be changed significantly. Besides, the adsorption isotherms of benzene and propylene in ZSM-5 at 298 and 443 K were simulated. The results exhibit that the different factors influenced the molecular adsorption at various temperatures and pressures, leading to the diffe- rent rules for the adsorption of benzene and propylene molecules in the zeolite. At a low pressure, the unfavorable energy of propylene/zeolite and the ＂commensurate freezing＂ phenomenon of benzene would make the loadings of itself higher than those of propylene. When pressure was higher than 5 kPa, the adsorption of benzene in ZSM-5 would nearly reach saturation.

A novel method for enhancing the stability of ZSM-5 zeolites used for catalytic cracking of LPG: Catalyst modification by dealumination and subsequent silicon loading

Composite structures of ZSM‐5 zeolites were prepared by the synthesis of mesopores and mi‐cropores using carbon nanotubes as a template. Dealumination of mesopores was performed selec‐tively using trichloroacetic acid, which could only diffuse into the mesopores and not the mi‐cropores owing to the size of the trichloroacetic acid molecules. Empty spaces are created in the catalyst as a result of removal of the Al atoms from the zeolite structure. If Si atoms fill the empty space, then the structure of the mesopores becomes similar to silicates, which do not have any cata‐lytic properties. Silicon containing solution was used to fill the empty spaces, and in doing so, a unique method was developed, by which silicon atoms can directly replace the extracted Al atoms from the mesopore structure. Therefore, by changing the geometry and properties of the mesopores and micropores, the amount of coke reduced from 14%for HZSM‐5 to 3%for the modified zeolite.

Rapid synthesis of ZSM-5 zeolite catalyst for amination of ethanolamine

ZSM-5 zeolite was rapidly synthesized in system containing ethylenediamine from the initial gel: (5?8) Na2O: 44 EDA:Al2O3:100 SiO2:4000 H2O. The crystals were lath-shaped. The effect of pretreatment and alkalinity on crystallinity was investigated. The pretreatment of silicate source can cut down the crystallization time. Tuning the system alkalinity and controlling crystallization time can ensure forming of pure crystal.

Physicochemical Features of Phosphorus-Modified ZSM-5 Zeolite and Its Performance on Catalytic Pyrolysis to Produce Ethylene

The physicochemical features of phosphorus-modified ZSM-5 zeolites (SiO2/Al2O3 molar ratio is 25) were characterized by XRD(X-ray diffraction), BET(Brunauer, Emmett and Teller spcific surface area measurement), NH3-TPD(ammonia temperature-programmed desorption) and MASNMR(magic angle spinning nuclear magnetic resonance), and the performance on catalytic pyrolysis to produce ethylene was investigated with a light hydrocarbon fixed bed micro-reactor with n-octane as feed. The results show that the acid site density, acid intensity and hydrothermal stability of ZSM-5 zeolite were improved by phosphorus modification. When P2O5 content in ZSM-5 zeolite is higher than 2.5%, phosphorus modification can prevent ZSM-5 zeolite crystal structure transformation from orthorhombic to monoclinic. In addition, the dealumination of ZSM-5 zeolite framework was moderated by phosphorus modification under high temperature hydrothermal treatment. The results of n-octane pyrolysis on phosphorus-modified ZSM-5 zeolites show that ethylene yields of zeolites with different phosphorus content are almost the same under the same n-octane conversion. However, the modified zeolites with higher pyrolysis activity give lower yield of propene, butene and total olefin than lower pyrolysis activity under the same n-octane conversion.

Exploring suitable ZSM-5/MCM-41 zeolites for catalytic cracking of n-dodecane: Effect of initial particle size and Si/Al ratio

In this study,various ZSM-5/MCM-41 micro/mesoporous zeolite composites have been prepared by alkalidesilication and surfactant-directed recrystallization of ZSM-5.The effects of particle size and Si/Al ratio of initial ZSM-5 zeolites on the structure and catalytic performance of ZSM-5/MCM-41 composites are studied.The results of XRD,TEM N_2-adsorption-desorption,NH_3-TPD and in situ FT-IR revealed that ordered hexagonal MCM-41 mesopores with 3-4 nm pore size were formed around ZSM-5 crystals,and the specific surface area and mesopore volume of composites increased with increasing the Si/Al ratio of initial ZSM-5.Catalytic cracking of n-dodecane(550℃,4 MPa) showed that the ZSM-5/MCM-41 composites obtained from the high Si/Al ratio and nano-sized initial ZSM-5 zeolites exhibited superior catalytic performance,with the improvement higher than 87%in the catalytic activities and 21%in the deactivation rate compared with untreated zeolites.This could be ascribed to their suitable pore structure,which enhanced the diffusion of reactant molecules in pores of catalysts.

Effects of Metal Oxide in ZSM-5 Zeolite on Its Catalytic Performance in FCC Process

Effects of metal oxide in ZSM-5 zeolite on its catalytic performance in fluid catalytic cracking reaction were studied via characterization by XRD and FT-IR spectroscopy using pyridine and collidine as molecular probes,and the modified ZSM-5 zeolite was evaluated in a micro reactor using standard light diesel fraction as the feedstock.Test results indicate that the metal species introduced into the ZSM-5 zeolite had led to the formation of Lewis acid centers.When the modified ZSM-5 zeolite with the metal species on its surface was used as the catalyst in FCC reaction,both the propylene yield and the propylene concentration in the liquefied petroleum gas increased,but in the meantime,more hydrogen and coke were formed at high conversion rate under the joint action of nonselective cracking of Lewis acid centers and dehydrogenation at metal centers on its outside surface.

Synthesis of ZSM-5 zeolite membranes without organic templates using a varying-concentration technique

Template-free nanosized ZSM-5 seeds with an average size of 15 nm were prepared from a synthesis solution with the composition 12Na2O∶100SiO2∶2Al2O3∶2500H2O. By the use of these seeds, thin ZSM-5 zeolite membranes were prepared on the outer surface of a porous α-alumina tube with a pore size of 2 μm in a gel system by varying-concentration synthesis with organic-free template. The first composition synthesis sol-gel was the same as seeds of molar composition and the second one was 12Na2O∶100SiO2∶2Al2O3∶5000H2O at 180 ℃ for 10 h, respectively. XRD shows that the film consists of well-crystallized ZSM-5 zeolite. SEM investigation indicats that the zeolite films on the supports are defect free and the film thickness is approximately 8 μm. The permeances for H2, N2, CH4 and CO2 are 8.94×10-7, 3.27×10-7, 3.9×10-7, 3.14×10-7 and 0.874×10-7 mol·m2·s-1·Pa-1, respectively. The ideal selectivity of membrane at room temperature for H2/CO2, H2/N2, H2/CH4 are 2.84, 2.73 and 2.29, respectively.

The Difference between ZSM-5 Zeolites Manufactured from Various Synthesis Systems and Their Catalytic Performances

ZSM-5 zeolites with similar St/Al ratio were synthesized successfully using various templates [n- butylamine （BTA）, tetrapropylammonium bromide （TPABr） and no template （NT）] under hydrothermal conditions, The samples were characterized by XRD, SEM, Py-IR and BET surface area measurements in order to understand the template eiTects and the differences between the ZSM-5 santples. The synthesis of ZSM-5 with organic templates was relatively easier than those with inorganic templates and withnut template. SEM results revealed that ZSM-5 synthesized with different templates had different morphologies in similar particle size. Toluene disproportiortation reaction was carried out over the catalyst samples to evaluate the catalytic properties. The results have shown that large crystals which have a correspondingly small external surface showed a high para-xylene selectivity, and the amount of C9^＋ and C5^＋ was much less than that obtained from zeolite with small crystals.

ZSM-5和ZSM-11分子筛催化苯与甲醇烷基化反应研究

采用水蒸气辅助晶化法合成ZSM-5、ZSM-11和多级孔ZSM-11分子筛,运用XRD、SEM、NH3-TPD、N2吸附-脱附和TG方法对合成的分子筛进行表征。结果表明:所合成的ZSM-5和ZSM-11分子筛的比表面积、微孔体积、晶粒大小和酸性等物化性质相似;多级孔ZSM-11分子筛引入了大量介孔,微孔体积得以保留。合成的分子筛催化苯与甲醇烷基化反应结果表明,ZSM-11相对于ZSM-5表现出更高的反应活性和稳定性,这是因为C7、C8等芳烃分子在ZSM-11孔道内扩散更快;多级孔ZSM-11相对于微孔ZSM-11反应活性进一步提升,在反应温度460℃、压力0.2 MPa、质量空速3 h-1的条件下,苯转化率达到54.3%,甲苯和二甲苯总选择性达到91.9%,其中二甲苯选择性为37.9%,该催化剂在反应240 h内保持良好的稳定性,相对于微孔ZSM-11,寿命显著提升。

Effect of Alkali Treatment on the Structure and Catalytic Properties of ZSM-5 Zeolite

Catalytic properties of ZSM-5 zeolite samples pretreated with NaOH solution have been investigated. The samples are characterized by XRD, SEM, chemical analysis, and N2 adsorption. The results indicate that mesopores are created in ZSM-5 crystals under alkali treatment without change the microporous structure and acidic strength of the zeolite, but the crystallinity is greatly decreased under severe treatment. IR indicates that the concentration of silanol is greatly enriched by alkali treatment. The etherification activities of ZSM-5 zeolites are greatly increased by alkali-treatment. The noticeably improved catalytic activity of treated samples is ascribed to the formation of mesopores and greatly enriched silanol group.