Research Progress on the Preparation of Inorganic/Natural Materials Composite Microspheres

Microspheres are a new type of drug carrier with great potential for development and application.Natural polymers have good biocompatibility,biodegradability,and are easily dispersed in living organisms,making them suitable for preparing microspheres.Inorganic materials(mainly inorganic minerals)have excellent mechanical properties and are inexpensive and easy to obtain.Through the coupling and hybridization of natural polymers and inorganic materials,they can complement each other's advantages and synergistically enhance efficiency,resulting in many excellent physical and chemical properties.Inorganic materials/natural polymer composite microspheres can be prepared by modifying natural polymers with inorganic materials through various methods such as emulsification crosslinking,solution mixing,in-situ synthesis,extrusion,etc.The application of inorganic materials/natural polymer composite microspheres in drug delivery systems has significant sustained-release effects,is safe and non-toxic,and the cost of carrier materials is relatively low,which has certain significance for the development of new drug carriers.This article reviews the recent research on the preparation,drug loading and release properties of inorganic material/natural polymer composite microspheres,analyzes the advantages and disadvantages of commonly used preparation methods,and looks forward to the development direction of composite microspheres.

Preparation of CuO-CoO-MnO/SiO_2 Nanocomposite Aerogels as Catalyst Carriers and Their Application in the Synthesis of Diphenyl Carbonate

CuO-CoO-MnO/SiO2 nanocomposite aerogels were prepared by using tetraethyl orthosilicate （TEOS） as Si source, and aqueous solution of Cu, Co and Mn acetates as transition metal sources via sol-gel process and supercritical drying （SCD） technique. The effect of synthesis conditions on gelation was investigated. Moreover, the composition of the CuO-CoO-MnO/SiO2 nanocomposite aerogels was characterized by electron dispersive spectroscopy （EDS） and X-ray photoelectron spectroscopy （XPS）, and the specific surface area of the nanocomposite aerogels was determined by the Brunauer-Emmett-Teller （BET） method. Diphenyl carbonate （DPC） as the product was analyzed by gas chromatography （GC）. The experimental results show that the range of optimal temperature for gelation is 30-45 ℃, and the pH is 3.0-4.5. CuO-CoO-MnO/SiO2 nanocomposite aerogels are porous with a specific surface area of 384.9-700.6 m2/g. Compared to CO2 SCD, ethanol SCD is even favorable to the formation of aerogel with high specific surface area. The transition metals content in the nanocomposite aerogels can be controlled to be 0.71at%-13.77at%. With CuO-CoO-MnO/SiO2 nanocomposite aerogels as catalyst carrier, the yield of DPC is in direct proportion to the atomic fraction of transition metals in the nanocomposite aerogels, and it is up to 26.31 mass%, which is much higher than that via other porous carriers.

Preparation of TiC/Ni_3Al Composites by Upward Melt Infiltration

TiC/Ni_3Al composites have been prepared using upward infiltration method. The densification was performed by both Ni_3Al melt filling and TiC sintering during the infiltration. The dissolution of TiC in liquid Ni_3Al has been evidenced by finding Ni_3(Al,Ti)C after fast cooling in the TiC/Ni_3Al composites. The dissolution may be responsible for the infiltration and sintering. Compared with downward infiltration, the upward infiltration brought about higher strength and fracture toughness and shorter infiltration time. TiC/20 vol. pct Ni_3Al composite processed by upward infiltration had a flexural strength of 1476 MPa with a statistic Weibull modulus of 20.2 and a fracture toughness of 20.4 MPa . Better mechanical properties may be attributed to melt unidirectional movement in upward infiltration.

Preparation and Microstructure of a Si-Mo Fused Slurry Coating on Carbon/Carbon Composites for Oxidation Protection

A coating of composition Si-40Mo (wt pct) was prepared by fused slurry coating method on the two-dimensional carbon/carbon (2D-C/C) composite to improve oxidation resistance. In the procedure of the fabrication, pure St slurry inner layer in the pre-coating was necessary to apply because of infiltration of liquid Si into the substrate during the sintering. The coating consists of Si continuous phase and MoSi2 particles. In addition, the infiltration of Si into the substrate and the SiC reaction layer between the coating and the C/C composite were observed. Oxidation behavior of coated and uncoated C/C composites was studied in cyclic mode. The oxidation resistance and the thermal shock resistance of the Si-Mo fused slurry coating were quite excellent at 1370℃.

Preparation technique of SiCp reinforced Al matrix composite

A new preparation technique-"block dispersal and cast" method is introduced, and three kinds of powder mixing methods, vertical, horizontal and inclining styles, are compared. The results demonstrate that the inclining style is the best way to mix powders. The Al and nano SiC powders are pressed into blocks, dipped into molten Al, stirred into mold so that SiC/Al matrix composites can be obtained at last. The microstructure of SiC particle reinforced Al matrix composite prepared by "block dispersal and cast" method have been studied using scanning electron microscopy (SEM). Phase analysis has also been conducted by means of X-ray diffraction (XRD). The results show that nano SiC particles can be dispersed uniformly in Al matrix. Thus, it is feasible to prepare SiC particle reinforced Al matrix composites by this method.

Facile Preparation of PVA-AA/TiO2 Composite Gel Particles and Their Tunable Photo-catalytic Property for the Degradation of Methyl Orange

In the presence of titanium dioxide powder, cross-linking reaction between commercial polyvinyl alcohol(PVA)-based macromonomer and acrylic acid(AA) was initiated with potassium persulfate in an emulsifying system. As a result, PVA-AA/TiO2 composite gel particles were obtained. The morphology and composition of the particles were analyzed with scanning electron microscopy(SEM), energy scattering x-ray spectroscopy(EDS), Fourier infrared spectroscopy(FTIR), and thermogravimetric analysis(TGA). The analysis results confirmed that the particles were the expected ones. TiO2 was dispersed homogeneously within the spheroidal particles. Compared to the control gel, the composite gel particles not only contained Ti element but also showed higher thermal stability. In addition, the photo-catalytic behavior of the particles for the degradation of methyl orange contained in aqueous solution was examined. The particles exhibited photocatalytic characteristic for the degradation of the model dye, which could be modulated by simply varying the amount of cross-linking agent or TiO2. The photo-catalytic degradation percentage of methyl orange maintained at 91%-96% after using the particles three times, which indicated that TiO2 could played its role repeatedly via being fixated within polyvinyl alcohol-based gel.

Preparation and Optical Properties of Nanocrystalline Ga0.62In0.38Sb Embedded in SiO2 Composite Films

Nanocrystalline Ga0.62In0.38Sb embedded in SiO2 matrix has been fabricated by radio frequency magnetron cosputtering. X-ray photoelectron spectroscopy strongly supports the existence of nanocrystalline Ga0.62In0.38Sb embedded in SiO2 matrix. The room-temperature Raman spectrum shows that the Raman peaks of the Ga0.62In0.38SbSiO2 composite film have a larger red shift of about 95.3 cm-1 (longitudinal-optic) and 120.1 cm-1 (transverseoptic) than those of the bulk GaSb. This can be explained by the phonon confinement and tensile stress effects. The room-temperature optical transmission spectra show that the absorption edge exhibits a large blue shift of about 2.43 eV compared with that of the bulk semiconductor, suggesting the existence of quantum size effects.

In-situ Preparation of Al/TiAl_3(P) Composite by Direct Reaction between Molten Al and TiO_2 Powder

TiAl3 particle reinforced pure Al composite has been made by direct reaction among molten Al, TiO2 and a flux. The composite exhibits high Synthetically properties. The strength and hardness are higher than those of pure Al matrix by 71.5% and 134% respectively However, the elongation is 20.36%, slightly lower than that of the Al matrix.

Review on preparation techniques of particle reinforced metal matrix composites

This paper reviews the investigation status of the techniques for preparation of metal matrix composites and the research outcomes achieved recently. The mechanisms, characteristics, application ranges and levels of development of these preparation techniques are analyzed. The advantages and the disadvantages of each technique are synthetically evaluated. Lastly, the future directions of research and the prospects for the preparation techniques of metal matrix composites are forecasted.

Preliminary Investigation of NiAl-TiB_2 Composite Prepared by Reaction Milling

Reaction-milled NiAl-TiB2 composite was fabricated by mechanical alloying elemental powders and hot pressing. TiB2 particles are distributed mostly in grain boundaries of the matrix. The compressive strain to failure of the composite at RT is about twice that of cast NiAl. The compressive yield stress at high temperatures is about 4.5 times higher than that of extruded NiAl, and is also much stronger than XD NiAl-TiB2 composites. Deformation behavior between 1000~1100℃ with different strain rates has been investigated

Cobalt phosphide-based composites as anodes for lithium-ion batteries:From mechanism,preparation to performance

With the further requirements of electronic products and powered vehicles,the development of a new generation with low-voltage and high-capacity anode materials is crucial for lithium-ion batteries(LIBs).Transition metal phosphides,especially cobalt phosphide(CoP)composites,have become a research hotspot for LIBs anode materials in recent years due to their high theoretical specific capacity,low polarization,and suitable voltage plateau.This review first systematically discusses the lithium storage mechanism and preparation methods of CoP in current research.Subsequently,the applications of CoP anode materials in LIBs are categorically reviewed,including the composites of CoP with various types of carbon materials and heterostructures.Finally,the challenges and future development directions of CoP anode materials are summarized to provide guidance for further improving the lithium storage performance of CoP and its practical applications.

Novel wood-plastic composite fabricated via modified steel slag:Preparation,mechanical and flammability properties

A novel method was developed to enhance the utilization rate of steel slag(SS).Through treatment of SS with phosphoric acid and aminopropyl triethoxysilane(KH550),we obtained modified SS(MSS),which was used to prepare MSS/wood-plastic composites(MSS/WPCs)by replacing talcum powder(TP).The composites were fabricated through melting blending and hot pressing.Their mechanical and combustion properties,which comprise heat release,smoke release,and thermal stability,were systematically investigated.MSS can improve the mechanical strength of the composites through grafting reactions between wood powder and thermoplastics.Notably,MSS/WPC#50(16wt%MSS)with an MSS-to-TP mass ratio of 1:1 exhibited optimal comprehensive performance.Compared with those of WPC#0 without MSS,the tensile,flexural,and impact strengths of MSS/WPC#50 were increased by 18.5%,12.8%,and 18.0%,respectively.Moreover,the MSS/WPC#50 sample achieved the highest limited oxygen index of 22.5%,the highest vertical burning rating at the V-1 level,and the lowest horizontal burning rate at 44.2 mm/min.The formation of a dense and stable char layer led to improved thermal stability and a considerable reduction in heat and smoke releases of MSS/WPC#50.However,the partial replacement of TP with MSS slightly compromised the mechanical and flame-retardant properties,possibly due to the weak grafting caused by SS powder agglomeration.These findings suggest the suitability of MSS/WPCs for high-value-added applications as decorative panels indoors or outdoors.

Methanation of carbon dioxide on Ni/ZrO_2-Al_2O_3 catalysts:Effects of ZrO_2 promoter and preparation method of novel ZrO_2-Al_2O_3 carrier

The novel nickel-based catalysts with a nickel content of 12 wt% were prepared with the zirconia-alumina composite as the supports. The new carriers, ZrO2 improved alumina, were synthesized by three methods, i.e., impregnation-precipitation, co-precipitation, and impregnation method. The catalytic properties of these catalysts were investigated in the methanation of carbon dioxide, and the samples were characterized by X-ray diffraction （XRD）, X-ray photoelectron spectroscope （XPS）, temperature-programmed reduction （TPR） and temperature-programmed desorption （TPD） techniques. The new catalysts showed higher catalytic activity and better stability than Ni/γ-Al2O3. Furthermore, as a support for new nickel catalyst, the ZrO2-Al2O3 composite prepared by the impregnation-precipitation method was more efficient than the other supports in the methanation of carbon dioxide. The highly dispersed zirconium oxide on the surface of γ-Al2O3 inhibited the formation of nickel aluminate-like phase, which was responsible for the better dispersion of Ni species and easier reduction of NiO species, leading to the enhanced catalytic performance of corresponding catalyst.

Effect of graphite powder as a forming filler on the mechanical properties of SiCp/Al composites by pressure infiltration

（38vo1% SiCp ＋ 2vo1% A1203f）/2024 A1 composites were fabricated by pressure infiltration. Graphite powder was introduced as a forming filler in preform preparation, and the effects of the powder size on the microstructures and mechanical properties of the final com- posites were investigated. The results showed that the composite with 15 μm graphite powder as a forming filler had the maximum tensile strength of 506 MPa, maximum yield strength of 489 MPa, and maximum elongation of 1.2%, which decreased to 490 MPa, 430 MPa, and 0.4%, respectively, on increasing the graphite powder size from 15 to 60 μm. The composite with 60 μm graphite powder showed the highest elastic modulus, and the value decreased from 129 to 113 GPa on decreasing the graphite powder size from 60 to 15 μm. The differences between these properties are related to the different microstructures of the corresponding composites, which determine their failure modes.

Enhanced Photoactivity of Layered Nanocomposite Materials Containing Rare Earths,Titanium Dioxide and Clay

The nanocomposite materials containing rare earths, titanium dioxide and clay (RE/TiO2/Clay) were characterized and tested for the photocatalytic decomposition of formaldehyde. The results show that nanocomposite materials prepared by doping appropriate rare earth elements have better photocatalytic properties than that prepared by doping excessive rare earth elements. The photocatalytic mechanism of composite materials was studied by integrating the theory of pho-tocatalysis with experiment results. Because the site of photocatalytic reaction was limited in the interspace of clay, photocatalytic reaction occurred by two steps: firstly, organic molecules dispersed into the interlayers of clay; secondly, organic molecules and photocatalyst of RE/TiO2 occurred photocatalytic reaction, resulting in forming carbon dioxide.

Preparation and Characterization of Antibacterial Zn^(2+)-Exchanged Montmorillonites

Zn-montmorillonites（Zn-MMTs） as antibacterial compounds were prepared by an ion-exchange reaction. The reaction time, initial pH value and molar ratios of CEC influencing zinc content in Zn-MMTs were investigated, and Zn-MMTs were characterized by means of EDX, XRD, XPS, and SEM. The results of bacterial growth tests were confirmed by determination of the minimum inhibition concentrations （MICs） and minimum bactericidal concentrations （MBCs）. The experimental results show that the zinc is confirmed as bivalent zinc state, the d001 basal spacing of Zn-MMTs is enlarged with the enhancement of the zinc content, and the particles of Zn-MMTs are formed with irregular shape. Moreover, the antibacterial activity of Zn-MMTs increases with increasing the zinc content, and Zn-MMT-3 containing 6.76 mass% of zinc exhibits optimum antibacterial activity against Escherichia coli and Staphylococcus aureus.