The ICP-AES method for the determination of Ge in GdSiGe series alloys was studied.As the three main elements in the alloys,Gd,Si,and Ge differ greatly from each other in chemical properties,it was difficult to pretre...The ICP-AES method for the determination of Ge in GdSiGe series alloys was studied.As the three main elements in the alloys,Gd,Si,and Ge differ greatly from each other in chemical properties,it was difficult to pretreat the sample.Two decomposition methods were compared,and a mixture of HNO3＋HF was used to decompose the sample and the effect of the HF amount on the sample decomposition was examined.The adsorption effect of GdF3 on Ge was discussed.Three GdSiGe series alloy samples were analyzed,and the RSDs of this method were in the range of 0.85%～2.66%.展开更多
Influence of A1 content on the machinability of AZ series cast Mg alloys was investigated. In order to evaluate the machinability of the alloys, measurements of the cutting forces during turning operations and surface...Influence of A1 content on the machinability of AZ series cast Mg alloys was investigated. In order to evaluate the machinability of the alloys, measurements of the cutting forces during turning operations and surface roughness were carried out as well as considering the microstructure and tensile properties. The results show that maximum tensile properties are observed with 2% （mass fraction） A1 addition to Mg. As the A1 content of the alloy increases above 2%, the cutting forces tend to reduce along with the ductility owing to the grain boundary precipitation of intermetallic phase （fl-Mgl7All2）. Cutting forces are able to increase as the cutting speed increases for all the alloys studied, and it＇s attributed to flank built up at the tip of the cutting tool during machining.展开更多
Fine TiFe series alloy powder was fabricated by magnesothermic reduction of ilmenite as main raw material.Adiabatic temperature of the FeTiO_(3)-Mg system was studied through thermodynamic analysis.Meanwhile,the chara...Fine TiFe series alloy powder was fabricated by magnesothermic reduction of ilmenite as main raw material.Adiabatic temperature of the FeTiO_(3)-Mg system was studied through thermodynamic analysis.Meanwhile,the characteristics of TiFe series alloy were described by XRD,SEM and grading analysis.It is shown that combustion synthesis of the FeTiO_(3)-Mg system can carry out due to its strong exothermic reaction through adiabatic temperature calculate.Ultrafine TiFe series alloy powder after leached for 5 h has reasonable phases and morphology with the particle distribution of 0.2 to 1μm.It indicates that in-situ magnesothermic reduction of natural ilmenite is a feasible way to fabricate ultrafine powder with a relatively lower cost.展开更多
The effects of stepped solution heat treatments on the dissolution of soluble remnant constituents and mechanical properties of 7055 aluminum alloy were investigated. It was shown that a suitable pretreatment at lower...The effects of stepped solution heat treatments on the dissolution of soluble remnant constituents and mechanical properties of 7055 aluminum alloy were investigated. It was shown that a suitable pretreatment at lower temperature can enable complete dissolution of the constituent particles in 7055 alloy without overheating by subsequent high temperature solution treatment. This in turn increased the tensile strength and fracture toughness of 7055 alloy to 805 MPa and 41.5 MPa·m 1/2 respectively, with approximately 9% tensile elongation. The near solvus pre precipitation following after high temperature solution treatment was also studied on 7055 aluminum alloy. The effect of the pre precipitation on the microstructure, age hardening and stress corrosion cracking of 7055 alloy was investigated. The optical and transimission electron microscopy observation show that the near solvus pre precipitation can be limited to grain boundary and enhance the discontinuity of grain boundary precipitates in the subsequent ageing. The stress corrosion cracking resistance of aged 7055 alloy can be improved via the pre precipitation with non deteriorated strength and plasticity.展开更多
The influence of Al content on machinability of AS series cast Mg alloys was studied. The assessment of machinability of Mg alloys was performed by measuring the cutting forces and surface roughness. The microstructur...The influence of Al content on machinability of AS series cast Mg alloys was studied. The assessment of machinability of Mg alloys was performed by measuring the cutting forces and surface roughness. The microstructure and the tensile properties were also studied. The results reveal that cutting forces are increased with the increase of the Al content. Surface roughness and mechanical properties are the highest for AS91 Mg alloy. It is assumed that the main mechanism, which has an influence on the mechanical properties, is the presence of intermetallic phases(Mg2Si and Mg17Al12). Cutting forces increase with the increase of the cutting speed in machining of all Mg alloys. These measured data are in accordance with the mechanical properties of the machined alloys.展开更多
The corrosion behavior of Mg-8Li-3Zn-Al alloy was investigated in neutral 3.5%NaCl aqueous solution by morphology observation and electrochemical tests.The weight loss method was to measure the corrosion rate.The elec...The corrosion behavior of Mg-8Li-3Zn-Al alloy was investigated in neutral 3.5%NaCl aqueous solution by morphology observation and electrochemical tests.The weight loss method was to measure the corrosion rate.The electrochemical results indicated that the corrosion resistance of Mg-8Li-3Zn-Al alloy in 3.5%NaCl solution is poorer than that in distilled water.The Cl-anion leads to the initiation and development of the corrosion pits.And the corrosion products are mainly Mg(OH)_(2).展开更多
As a part of the systematical investigation of the phase relationships of the Zn-Al base alloys,decomposi- tion of the supersaturated phase β_S in a eutectoid Zn-Al-Cu-Si alloy was studied by hardness testing,opti- c...As a part of the systematical investigation of the phase relationships of the Zn-Al base alloys,decomposi- tion of the supersaturated phase β_S in a eutectoid Zn-Al-Cu-Si alloy was studied by hardness testing,opti- cal,electron microscopy and X-ray diffraction.Com- pared to the monotectoid Zn-Al-Cu-Si alloy,a similar sequence of decomposition was found to consist of three stages of phase transformation,which were in accordance to various equilibrium reactions at the temperatures above the ageing temperatures.展开更多
The interaction between Zn-AI eutectic alloy and Al203p/6061AI composites in the vacuum furnace was investigated. Great attention has been paid to the elements diffusion, the microstructure and formation of the interf...The interaction between Zn-AI eutectic alloy and Al203p/6061AI composites in the vacuum furnace was investigated. Great attention has been paid to the elements diffusion, the microstructure and formation of the interface between Zn-AI eutectic alloy and Al2O3p/6061AI composites. Experimental results show that Zn-AI eutectic alloy has a good wetting ability to Al2O3p/6061 Al composites and the wetting angle decreases with increasing the temperature in vacuum. After the interaction, an interaction layer forms between Zn-AI alloy and Al2O3p/6061 Al composites. The phases in the interaction layer mainly consist of α-AI(Zn), Al2O3 and CuZn5 resulted from the diffusion of elements from the Zn-AI alloy. Several porosities distribute in the region near the interface of the Zn-AI alloy/interaction layer. The amount of shrinkage voids in the interacting layer is relevant to the penetration of Zn element into Al2O3p/6061Al composites which is a function of temperature. So it is necessary to lower heating temperature in order to limit the Zn penetration.展开更多
Phase transformation and microstructural change of an extruded eutectoid Zn-Al alloy Zn76Al22Cu2 (wt pct) were investigated during creep testing by using SEM and X-ray diffraction techniques. Creep induced decompositi...Phase transformation and microstructural change of an extruded eutectoid Zn-Al alloy Zn76Al22Cu2 (wt pct) were investigated during creep testing by using SEM and X-ray diffraction techniques. Creep induced decomposition of a metastable η'T phase and a four phase transformation, α+ ε →T' +η, occurred during the creep testing. Also a microstructural change was observed from a lamellar structure into a spheroidized structure in the rupture part of the extruded alloy. It provided evidence of creep induced phase transformations which occurred in ageing process. The mechanism of creep rupture of the extruded Zn-Al alloy was also discussed.展开更多
The nanostructural evolution and phase transformation of the films of a Zn-Al based alloy (Zn68Al10Cu22 in wt pct) have been studied by using X-ray diffraction and scanning electron microscopy. Nanostructural thin fil...The nanostructural evolution and phase transformation of the films of a Zn-Al based alloy (Zn68Al10Cu22 in wt pct) have been studied by using X-ray diffraction and scanning electron microscopy. Nanostructural thin films of the Zn-AI based alloy were produced by using an electron beam deposition technique. It was found that a nanocrystalline phase η'n had a strong preferred crystal orientation at (0002) crystal planes in the as-deposited films. During ageing at 220℃, the decomposition of nanophase η'n started with clustering to form Z-zones, and transitionai phase, which was accompanied by an eutectoid decomposition of the η'n phase: η'n β'eut T'. Decomposition, such as clustering and the formation of the Z-zones, and the transitionai phase etc. were observed in the nanophase β'eut. The formation and the decomposition of the transitionai phase of micrometers in size were involved in the decomposition of the main nanophase η'n. The mechanism of the Z-zones formation and the stability of nanophases were discussed.展开更多
The method of controlling separating anode and separating power source was used to perform orthogonal optimization for the parameters in electroplating Zn Al alloy.The electroplating Zn-Al alloy technology was decide...The method of controlling separating anode and separating power source was used to perform orthogonal optimization for the parameters in electroplating Zn Al alloy.The electroplating Zn-Al alloy technology was decided, in which the content of Al is about 12%-15% .展开更多
Furnace cooling is a slow cooling process. It is of importance to study structural evolution and its effects on the properties of alloys during the furnace cooling. Decomposition of aluminium rich α phase in a furnac...Furnace cooling is a slow cooling process. It is of importance to study structural evolution and its effects on the properties of alloys during the furnace cooling. Decomposition of aluminium rich α phase in a furnace cooled eutectoid Zn-Al based alloy was studied by transmission electron microscopy. Two kinds of precipitates in the α phase were detected in the FCZA22 alloy during ageing at 170℃. One was the hcp transitional α＂ m phase which aooears as directional rods and the round precipitates. The other was the fcc α＇m phase. 〈101〉. The orientation relationship between the a phase and transitional phase α＇m was determined as （022）α＇m （fcc）//（022^-）α（fcc）, [1^-11]α＇m, （fcc）//[2^-33]α（fcc）. The non-equilibrium phase decomposition of the α phase is discussed in correlation with the equilibrium phase relationships.展开更多
A continuously cast eutectoid Zn-Al alloy was extruded at about 250℃ and the complex microstructures of three phases (α. ε and η'E) were observed in the extruded eutectoid Zn-Al alloy.The fcc Al-rich α phase ...A continuously cast eutectoid Zn-Al alloy was extruded at about 250℃ and the complex microstructures of three phases (α. ε and η'E) were observed in the extruded eutectoid Zn-Al alloy.The fcc Al-rich α phase appeared as isolated particles with clear boundaries instead of the α phase occurring with diffuse boundary within the dendrites of the as-cast structure. A new unstable phase η'E was determined to have hexagonal close packed crystal structure. The decomposed β's, phase comprised the matrix. The new phase η'E decompoeed and a four phase transformation α+ε T'+η occurred afterwards during the isothermal holding. The extruded alloy tended to be stable after these two phase transformations. The early shrinkage and the following increase in dimension were related to the decomposition of the new phase η'E and the four phase transformation.展开更多
Both furnace cooled and as-cast eutectoid Zn-Al alloys were investigated under external tensile stress at 100℃. It was observed that the external tensile stress caused decomposition of two metastable phases η'T ...Both furnace cooled and as-cast eutectoid Zn-Al alloys were investigated under external tensile stress at 100℃. It was observed that the external tensile stress caused decomposition of two metastable phases η'T and η'S which derived from both original state of the alloy, and a phase transformation, αf +ε→T' +η， in both furnace cooled and as-cast eutectoid Zn-Al alloys. Also spheroidized structure formed partially during tensile testing. Superplasticity of the alloy has been discussed correlating with the phase transformations and microstructural changes.展开更多
基金Project supported by the New Technology and New Method Item of Ministry of Science and Technology of PRC(2005JG200030)
文摘The ICP-AES method for the determination of Ge in GdSiGe series alloys was studied.As the three main elements in the alloys,Gd,Si,and Ge differ greatly from each other in chemical properties,it was difficult to pretreat the sample.Two decomposition methods were compared,and a mixture of HNO3＋HF was used to decompose the sample and the effect of the HF amount on the sample decomposition was examined.The adsorption effect of GdF3 on Ge was discussed.Three GdSiGe series alloy samples were analyzed,and the RSDs of this method were in the range of 0.85%～2.66%.
文摘Influence of A1 content on the machinability of AZ series cast Mg alloys was investigated. In order to evaluate the machinability of the alloys, measurements of the cutting forces during turning operations and surface roughness were carried out as well as considering the microstructure and tensile properties. The results show that maximum tensile properties are observed with 2% （mass fraction） A1 addition to Mg. As the A1 content of the alloy increases above 2%, the cutting forces tend to reduce along with the ductility owing to the grain boundary precipitation of intermetallic phase （fl-Mgl7All2）. Cutting forces are able to increase as the cutting speed increases for all the alloys studied, and it＇s attributed to flank built up at the tip of the cutting tool during machining.
基金This work was financially supported by the Guangxi Science Research and Technology Exploiture Item(05112001-2A4)the Application Basic Research of Guangxi Natural Science Foundation(0575104).
文摘Fine TiFe series alloy powder was fabricated by magnesothermic reduction of ilmenite as main raw material.Adiabatic temperature of the FeTiO_(3)-Mg system was studied through thermodynamic analysis.Meanwhile,the characteristics of TiFe series alloy were described by XRD,SEM and grading analysis.It is shown that combustion synthesis of the FeTiO_(3)-Mg system can carry out due to its strong exothermic reaction through adiabatic temperature calculate.Ultrafine TiFe series alloy powder after leached for 5 h has reasonable phases and morphology with the particle distribution of 0.2 to 1μm.It indicates that in-situ magnesothermic reduction of natural ilmenite is a feasible way to fabricate ultrafine powder with a relatively lower cost.
文摘The effects of stepped solution heat treatments on the dissolution of soluble remnant constituents and mechanical properties of 7055 aluminum alloy were investigated. It was shown that a suitable pretreatment at lower temperature can enable complete dissolution of the constituent particles in 7055 alloy without overheating by subsequent high temperature solution treatment. This in turn increased the tensile strength and fracture toughness of 7055 alloy to 805 MPa and 41.5 MPa·m 1/2 respectively, with approximately 9% tensile elongation. The near solvus pre precipitation following after high temperature solution treatment was also studied on 7055 aluminum alloy. The effect of the pre precipitation on the microstructure, age hardening and stress corrosion cracking of 7055 alloy was investigated. The optical and transimission electron microscopy observation show that the near solvus pre precipitation can be limited to grain boundary and enhance the discontinuity of grain boundary precipitates in the subsequent ageing. The stress corrosion cracking resistance of aged 7055 alloy can be improved via the pre precipitation with non deteriorated strength and plasticity.
基金Ins. Telat TüRKYILMAZ and Ins. Ali Riza GüN for their support
文摘The influence of Al content on machinability of AS series cast Mg alloys was studied. The assessment of machinability of Mg alloys was performed by measuring the cutting forces and surface roughness. The microstructure and the tensile properties were also studied. The results reveal that cutting forces are increased with the increase of the Al content. Surface roughness and mechanical properties are the highest for AS91 Mg alloy. It is assumed that the main mechanism, which has an influence on the mechanical properties, is the presence of intermetallic phases(Mg2Si and Mg17Al12). Cutting forces increase with the increase of the cutting speed in machining of all Mg alloys. These measured data are in accordance with the mechanical properties of the machined alloys.
基金This work was supported by the financial support of the National Natural Science Foundation of China(No.41276074)National Research Program of China(No.2014CB643304).
文摘The corrosion behavior of Mg-8Li-3Zn-Al alloy was investigated in neutral 3.5%NaCl aqueous solution by morphology observation and electrochemical tests.The weight loss method was to measure the corrosion rate.The electrochemical results indicated that the corrosion resistance of Mg-8Li-3Zn-Al alloy in 3.5%NaCl solution is poorer than that in distilled water.The Cl-anion leads to the initiation and development of the corrosion pits.And the corrosion products are mainly Mg(OH)_(2).
文摘As a part of the systematical investigation of the phase relationships of the Zn-Al base alloys,decomposi- tion of the supersaturated phase β_S in a eutectoid Zn-Al-Cu-Si alloy was studied by hardness testing,opti- cal,electron microscopy and X-ray diffraction.Com- pared to the monotectoid Zn-Al-Cu-Si alloy,a similar sequence of decomposition was found to consist of three stages of phase transformation,which were in accordance to various equilibrium reactions at the temperatures above the ageing temperatures.
文摘The interaction between Zn-AI eutectic alloy and Al203p/6061AI composites in the vacuum furnace was investigated. Great attention has been paid to the elements diffusion, the microstructure and formation of the interface between Zn-AI eutectic alloy and Al2O3p/6061AI composites. Experimental results show that Zn-AI eutectic alloy has a good wetting ability to Al2O3p/6061 Al composites and the wetting angle decreases with increasing the temperature in vacuum. After the interaction, an interaction layer forms between Zn-AI alloy and Al2O3p/6061 Al composites. The phases in the interaction layer mainly consist of α-AI(Zn), Al2O3 and CuZn5 resulted from the diffusion of elements from the Zn-AI alloy. Several porosities distribute in the region near the interface of the Zn-AI alloy/interaction layer. The amount of shrinkage voids in the interacting layer is relevant to the penetration of Zn element into Al2O3p/6061Al composites which is a function of temperature. So it is necessary to lower heating temperature in order to limit the Zn penetration.
文摘Phase transformation and microstructural change of an extruded eutectoid Zn-Al alloy Zn76Al22Cu2 (wt pct) were investigated during creep testing by using SEM and X-ray diffraction techniques. Creep induced decomposition of a metastable η'T phase and a four phase transformation, α+ ε →T' +η, occurred during the creep testing. Also a microstructural change was observed from a lamellar structure into a spheroidized structure in the rupture part of the extruded alloy. It provided evidence of creep induced phase transformations which occurred in ageing process. The mechanism of creep rupture of the extruded Zn-Al alloy was also discussed.
文摘The nanostructural evolution and phase transformation of the films of a Zn-Al based alloy (Zn68Al10Cu22 in wt pct) have been studied by using X-ray diffraction and scanning electron microscopy. Nanostructural thin films of the Zn-AI based alloy were produced by using an electron beam deposition technique. It was found that a nanocrystalline phase η'n had a strong preferred crystal orientation at (0002) crystal planes in the as-deposited films. During ageing at 220℃, the decomposition of nanophase η'n started with clustering to form Z-zones, and transitionai phase, which was accompanied by an eutectoid decomposition of the η'n phase: η'n β'eut T'. Decomposition, such as clustering and the formation of the Z-zones, and the transitionai phase etc. were observed in the nanophase β'eut. The formation and the decomposition of the transitionai phase of micrometers in size were involved in the decomposition of the main nanophase η'n. The mechanism of the Z-zones formation and the stability of nanophases were discussed.
文摘The method of controlling separating anode and separating power source was used to perform orthogonal optimization for the parameters in electroplating Zn Al alloy.The electroplating Zn-Al alloy technology was decided, in which the content of Al is about 12%-15% .
文摘Furnace cooling is a slow cooling process. It is of importance to study structural evolution and its effects on the properties of alloys during the furnace cooling. Decomposition of aluminium rich α phase in a furnace cooled eutectoid Zn-Al based alloy was studied by transmission electron microscopy. Two kinds of precipitates in the α phase were detected in the FCZA22 alloy during ageing at 170℃. One was the hcp transitional α＂ m phase which aooears as directional rods and the round precipitates. The other was the fcc α＇m phase. 〈101〉. The orientation relationship between the a phase and transitional phase α＇m was determined as （022）α＇m （fcc）//（022^-）α（fcc）, [1^-11]α＇m, （fcc）//[2^-33]α（fcc）. The non-equilibrium phase decomposition of the α phase is discussed in correlation with the equilibrium phase relationships.
文摘A continuously cast eutectoid Zn-Al alloy was extruded at about 250℃ and the complex microstructures of three phases (α. ε and η'E) were observed in the extruded eutectoid Zn-Al alloy.The fcc Al-rich α phase appeared as isolated particles with clear boundaries instead of the α phase occurring with diffuse boundary within the dendrites of the as-cast structure. A new unstable phase η'E was determined to have hexagonal close packed crystal structure. The decomposed β's, phase comprised the matrix. The new phase η'E decompoeed and a four phase transformation α+ε T'+η occurred afterwards during the isothermal holding. The extruded alloy tended to be stable after these two phase transformations. The early shrinkage and the following increase in dimension were related to the decomposition of the new phase η'E and the four phase transformation.
文摘Both furnace cooled and as-cast eutectoid Zn-Al alloys were investigated under external tensile stress at 100℃. It was observed that the external tensile stress caused decomposition of two metastable phases η'T and η'S which derived from both original state of the alloy, and a phase transformation, αf +ε→T' +η， in both furnace cooled and as-cast eutectoid Zn-Al alloys. Also spheroidized structure formed partially during tensile testing. Superplasticity of the alloy has been discussed correlating with the phase transformations and microstructural changes.
