Effect of KOH treatment on structural and photovoltaic properties of ZnO nanorod arrays

ZnO nanorod arrays （NRs） were synthesized on the fluorine-doped SnO2 transparent conductive glass （FTO） by a simple chemical bath deposition （CBD） method combined with alkali-etched method in potassium hydroxide （KOH） solution. X-ray diffraction （XRD）, scanning electron microscopy （SEM） and current-voltage （I-V） curve were used to characterize the structure, morphologies and optoelectronic properties. The results demonstrated that ZnO NRs had wurtzite structures, the morphologies and photovoltaic properties of ZnO NRs were closely related to the concentration of KOH and etching time, well-aligned and uniformly distributed ZnO NRs were obtained after etching with 0.1 mol/L KOH for 1 h. ZnO NRs treated by KOH had been proved to have superior photovoltaic properties compared with high density ZnO NRs. When using ZnO NRs etched with 0.1 mol/L KOH for 1 h as the anode of solar cell, the conversion efficiency, short circuit current and open circuit voltage, compared with the unetched ZnO NRs, increased by 0.71%, 2.79 mA and 0.03 V, respectively.

Hydrothermal Synthesis and Field Enhancement Behavior of ZnO Nanorods Pattern

We provide a new way to prepare ZnO nanorods pattern from the solution composed of hexamethylenetetramine （HMT） and Zn（NO3）2. The substrate is ITO substrate covered by well ordered Au islands. Since Au and the underneath ITO substrate have two different nucleation rates in the initial stage of heterogeneous nucleation process, the subsequent ZnO growth on the quick nucleating area takes place under diffusion control and is able to confine the synthesis of ZnO nanorods to specific locations. The concentrations of zinc nitrate and HMT are well adjusted to show the possibility of the new route for the patterning of the ZnO nanorods. Furthermore, the nanorods pattern was characterized by X-ray diffraction and photoluminescence and the performance of field emission property from ZnO nanorod patterns was investigated. The ZnO nanorods pattern with a good alignment also shows a good field enhancement behavior with a high value of the field enhancement factor.

Effect of annealing treatment on morphologies and gas sensing properties of ZnO nanorods

The high-temperature stabilization of ZnO nanorods synthesized by hydrothermal treatment was investigated. The structure and morphologies of ZnO nanorods were characterized by XRD and SEM, respectively. The thermal stability of ZnO nanorods was also detected by thermal gravity analyzing. Thermal annealing treatment results indicate that ZnO nanorods are fundamentally stable when annealing temperature is lower than 600 ℃. When annealing temperature is beyond 600℃, the diameters of ZnO nanorods obviously decrease and the aggravating tendency of nanorods between each other also increase. Annealing treatment can greatly influence the gas sensing properties of ZnO nanorods. Comparing with ZnO nanorods without annealing treatment, the gas sensing property of ZnO nanorods to H2 with concentration of 2.5×10-6 can increase from 2.22 to 3.56. ZnO nanorods annealed at 400 ℃ exhibit optimum gas sesing property to H2 gas.

Effect of calcination temperatures on photocatalytic H_(2)O_(2)-production activity of ZnO nanorods

Photocatalytic hydrogen peroxide(H_(2)O_(2))production from O_(2) and H2O is an ideal process for solar‐to‐chemical energy conversion.Herein,ZnO nanorods are prepared via a simple hydrothermal method for photocatalytic H_(2)O_(2) production.The ZnO nanorods exhibit varied performance with different calcination temperatures.Benefiting from calcination,the separation efficiency of photo‐induced carriers is significantly improved,leading to the superior photocatalytic activity for H_(2)O_(2) production.The H_(2)O_(2) produced by ZnO calcined at 300℃ is 285μmol L^(−1),which is over 5 times larger than that produced by untreated ZnO.This work provides an insight into photocatalytic H2O2 production mechanism by ZnO nanorods,and presents a promising strategy to H2O2 production.

Effects of surface adsorbed oxygen, applied voltage, and temperature on UV photoresponse of ZnO nanorods

The ultraviolet（UV） photoresponses of ZnO nanorods directly grown on and between two micro Au-electrodes by using electric-field-assisted wet chemical method are measured comprehensively under different conditions, including ambient environment, applied bias voltage, gate voltage and temperature. Experimental results indicate that the photoresponses of the ZnO nanorods can be modulated by surface oxygen adsorptions, applied voltages, as well as temperatures. A model taking into account both surface adsorbed oxygen and electron-hole activities inside ZnO nanorods is proposed. The enhancement effect of the bias voltage on photoresponse is also analyzed. Experimental results shows that the UV response time（to 63%） of ZnO nanorods in air and at 59°C could be shortened from 34.8 s to 0.24 s with a bias of 4 V applied between anode and cathode.

Effect of rubrene:P3HT bilayer on photovoltaic performance of perovskite solar cells with electrodeposited ZnO nanorods

Improved photovoltaic performance of perovskite solar cells is demonstrated through the synergistic effect of electrodeposited ZnO nanorods and rubrene：P3HT bilayer as electron and hole-transporting layers,respectively. Highly crystalline ZnO nanorods were obtained by electrochemical deposition in a chloride medium. Additionally, rubrene interlayer was able to passivate or cover the grain boundaries of perovskite film effectively that led to reduced leakage current. A perovskite solar cell optimized with ZnO nanorods and rubrene：P3HT bilayer achieved a maximum efficiency of 4.9% showing reduced hysteresis behavior compared with the device having P3HT as the only hole-transporting layer. The application of longer nanorods led to better perovskite infiltration and shorter charge carrier path length. These results highlight the potential of electrodeposited ZnO nanorods and rubrene：P3HT bilayer as charge selective layers for efficient perovskite solar cells.

Fabrication of highly oriented ZnO nanorod arrays by galvanostatic deposition

Highly oriented ZnO nanorod arrays were successfully prepared on the indium tin oxide （ITO） substrate using a galvanostatic electrodeposition method. The ITO substrate was pretreated with ZnO nanoparticles via simple low-temperature solution route. The crystallinity, microstructure of surface, and optical properties of the obtained ZnO were characterized by X-ray diffraction, scanning electron microscope, and transmittance spectrum. The results indicate that the average diameter of ZnO nanorod arrays is about 30 nm, and the narrow size distribution ranges from 20 to 50 nm. The nanorod arrays are growing along wavelength of incident is over 380 nm, the ZnO nanorod arrays growth mechanism of the nanorod arrays was discussed. [001] direction with an orientation perpendicular to the substrate. When the show a high optical transmission of above 95%. Furthermore, the possible

Quantitative modeling, optimization, and verification of ^(63)Nipowered betavoltaic cells based on three-dimensional ZnO nanorod arrays

Betavoltaic cells(BCs)are promising self-generating power cells with long life and high power density.However,the low energy conversion efficiency(ECE)has limitations in practical engineering applications.Widebandgap semiconductors(WBGSs)with three-dimensional(3-D)nanostructures are ideal candidates for increasing the ECE of BCs.This paper proposes hydrothermally grown ZnO nanorod arrays(ZNRAs)for ^(63)Ni-powered BCs.A quantitative model was established for simulation using the parameter values of the dark characteristics,which were obtained from the experimental measurements for a simulated BC based on a Ni-incorporated ZNRAs structure.Monte Carlo(MC)modeling and simulation were conducted to obtain the values of the β energy deposited in ZNRAs with different nanorod spacings and heights.Through the simulation and optimization of the 3-D ZNRAs and 2-D ZnO bulk structures,the performance of the ^(63)Ni-powered BCs based on both structures was evaluated using a quantitative model.The BCs based on the 3-D ZNRAs structure and 2-D ZnO bulk structure achieved a maximum ECE of 10.1%and 4.69%,respectively,which indicates the significant superiority of 3-D nanostructured WBGSs in increasing the ECE of BCs.

ZnO nanorod arrays with tunable size and field emission properties on an ITO substrate achieved by an electrodeposition method

In the present work, vertically aligned ZnO nanorod arrays with tunable size are successfully synthesized on nonseeded ITO glass substrates by a simple electrodeposition method. The effect of growth conditions on the phase, morphology, and orientation of the products are studied in detail by X-ray diffraction （XRD）, scanning electron mi-croscopy （SEM）, and transmission electron microscopy （TEM）. It is observed that the as-prepared nanostructures exhibit a preferred orientation along c axis, and the size and density of the ZnO nanorod can be controlled by changing the concentration of ZnC12. Field emission properties of the as-synthesized samples with different diameters are also studied, and the results show that the nanorod arrays with a smaller diameter and appropriate rod density exhibit better emission properties. The ZnO nanorod arrays show a potential application in field emitters.

Improved efficiency and stability of perovskite solar cells with molecular ameliorating of ZnO nanorod/perovskite interface and Mg-doping ZnO

Despite the advanced efficiency of perovskite solar cells(PSCs),electron transportation is still a pending issue.Here the polymer polyvinylpyrrolidone(PVP)is used to enhance the electron injection,which is thanks to the passivation of the defects at the interface between the ZnO electron transporting layer(ETL)and the perovskite.The application of the PVP layer inhibits the device degradation,and 80%of the primary efficiency is kept after 30 d storage in air condition.Additionally,the efficiency of the device is further enhanced by improving the conductivity and crystallinity of the ZnO ETL via Magnesium(Mg)doping in the ZnO nanorods(ZnO NRs).Moreover,the preparation parameters of the ZnO NRs are optimized.By employing the high-crystallinity ZnO ETL and the PVP layer,the power conversion efficiency(PCE)of the champion device is increased from 16.29%to 19.63%.These results demonstrate the advantages of combining mesoscale manipulation with interface modification and doping together.

The Inorganic-organic Hybrid Junction with n-ZnO Nanorods/p-polyfluorene Structure Grown with Low-temperature Aqueous Chemical Growth Method

The inorganic-organic hybrid junction was synthesized on ITO glass substrate, which was consisted of an n-type ZnO nanorods （NRs） grown by low-temperature aqueous chemical growth method and a p-type polyfluorene （PF） organic film fabricated by spin-coating. The experimental results indicate that densely and uniformly distributed ZnO nanorods are successfully grown on the PF layer. The thickness of the PF layer plays a dominant role for the current-voltage （I-V） characteristic of the ZnO NRs/PF inorganic-organic hybrid junction device, and a p-n junction with obviously rectifying behavior is achieved with optimal PF layer thickness. The photoluminescence （PL） spectrum covering the broad visible range was obtained from the n-ZnO nanorods/p-polyfluorene （PF） structure, which was originated from the combination of the PF-related blue emission and the ZnO-related deep level emission.

Photoactive area modification in bulk heterojunction organic solar cells using optimization of electrochemically synthesized ZnO nanorods

In this work, ZnO nanorod arrays grown by an electrochemical deposition method are investigated. The crucial parameters of length, diameter, and density of the nanorods are optimized over the synthesize process and nanorods growth time. Crystalline structure, morphologies, and optical properties of ZnO nanorod arrays are studied by different techniques such as x-ray diffraction, scanning electron microscope, atomic force microscope, and UV-visible transmission spectra. The ZnO nanorod arrays are employed in an inverted bulk heterojunction organic solar cell of Poly （3-hexylthiophene）：[6- 6] Phenyl-（6） butyric acid methyl ester to introduce more surface contact between the electron transporter layer and the active layer. Our results show that the deposition time is a very important factor to achieve the aligned and uniform ZnO nanorods with suitable surface density which is required for effective infiltration of active area into the ZnO nanorod spacing and make a maximum interfacial surface contact for electron collection, as overgrowing causes nanorods to be too dense and thick and results in high resistance and lower visible light transmittance. By optimizing the thickness of the active layer on top of ZnO nanorods, an improved efficiency of 3.17% with a high FF beyond 60% was achieved.

Ag-doped ZnO nanorods synthesized by two-step method

A two-step method is adopted to synthesize Ag-doped ZnO nanorods. A ZnO seed layer is first prepared on a glass substrate by thermal decomposition of zinc acetate. Ag-doped ZnO nanorods are then assembled on the ZnO seed layer using the hydrothermal method. The influences of the molar percentage of Ag ions to Zn ions （RAg/zn） on the structural and optical properties of the ZnO nanorods obtained are carefully studied using X-ray diffractometry, scanning electron microscopy and spectrophotometry. Results indicate that Ag ions enter into the crystal lattice through the substitution of Zn ions. The （002） c-axis-preferred orientation of the ZnO nanorods decreases as RAg/Zn increases. At RAg/Zn 〉 1.0%, ZnO nanorods lose their c-axis-preferred orientation and generate Ag precipitates from the ZnO crystal lattice. The average transmissivity in the visible region first increases and then decreases as RAg/Zn increases. The absorption edge is first blue shifted and then red shifted. The influence of Ag doping on the average head face, and axial dimensions of the ZnO nanorods may be optimized to improve the average transmissivity at RAg/Zn 〈 1.0%.

Improving light trapping and conversion efficiency of amorphous silicon solar cell by modified and randomly distributed ZnO nanorods

Three-dimensional （3D） nanostructures in thin film solar cells have attracted significant attention due to their appli- cations in enhancing light trapping. Enhanced light trapping can result in more effective absorption in solar cells, thus leading to higher short-circuit current density and conversion efficiency. We develop randomly distributed and modified ZnO nanorods, which are designed and fabricated by the following processes： the deposition of a ZnO seed layer on sub- strate with sputtering, the wet chemical etching of the seed layer to form isolated islands for nanorod growth, the chemical bath deposition of the ZnO nanorods, and the sputtering deposition of a thin Al-doped ZnO （ZnO：Al） layer to improve the ZnO/Si interface. Solar cells employing the modified ZnO nanorod substrate show a considerable increase in solar energy conversion efficiency.

Microstructure Characterization of Single-crystal ZnO Nanorods Synthesized by Solvothermal at Low Temperature

Single-crystalline ZnO nanorods have been synthesized by a simple solvothermal process at low temperature. Transmission electron microscopy （TEM） observations have confirmed that the as-synthesized products have rod-like morphologies with diameters ranging from several nanometers to 30 nm and lengths from 100 nm to 2 μm. Such hexagonal ZnO nanorods are structurally uniform and the growth direction is identified to be [0001]. Growth mechanism of the ZnO nanorods was proposed.

Structural, Optical and Photocatalytic Properties of Cu2+ Doped ZnO Nanorods with Using HMTA Solvent Prepared by Hydrothermal Method

In this experiment, Cu2+ doped ZnO (Cu-ZnO) nanorods materials have been fabricated by hydrothermal method. Cu2+ ions were doped into ZnO with ratios of 2, 5 and 7 mol.% (compared to the mole’s number of Zn2+). The hexamethylenetetramine (HMTA) solvent used for the fabrication of Cu-ZnO nanorods with the mole ratio of Zn2+:HMTA = 1:4. The characteristics of the materials were analyzed by techniques, such as XRD, Raman shift, SEM and UV-vis diffuse reflectance spectra (DRS). The photocatalytic properties of the materials were investigated by the decomposition of the methylene blue (MB) dye solution under ultraviolet light. The results show that the size of Cu-ZnO nanorods was reduced when the Cu2+ doping ratio increased from 2 mol.% to 7 mol.%. The decomposition efficiency of the MB dye solution reached 92% - 97%, corresponding to the Cu2+ doping ratio changed from 2 - 7 mol.% (after 40 minutes of ultraviolet irradiation). The highest efficiency for the decomposition of the MB solution was obtained at a Cu2+ doping ratio of 2 mol.%.

Synthesize of ZnO Nanorods on Quartz Substrates with Seed Layer via Hydrothermal Method: Influence of Solution Concentration

Vertically oriented ZnO nanorods have been synthesized by hydrothermal method on quartz substrates with a seed layer. The influence of solution concentration on the morphology, structural and optical properties was analyzed. Results indicated that with the increase of solution concentration, the diameter and uniformity of ZnO nanorods increased. And the preferred orientation is obviously which shows better crystal quality. Typically, when the solution concentration is 0.03 mol/L, the nanorods exhibit a stronger UV emission peak located around 380 nm. In the visible region, all synthesized samples demonstrate more than 80% of optical transparency.

Improved Low-Temperature Aqueous Synthesis of ZnO Nanorods and Their Use in SERS Detection of 4-ABT and RDX

The growth-controlled synthesis of zinc oxide nanorods (ZnO NR) in the aqueous phase has been investigated. The rods were grown on ZnO films previously deposited onto Si(100) and indium tin oxide (ITO) substrates by RF magnetron sputtering. The formation of the rods took place in the presence of hexamethylenetetramine (HMT) as habit-control reagent. The grains in the base ZnO film acted as seeds that promoted the longitudinal growth of the oxide. As-synthesized base films and rods were characterized by X-ray diffraction, scanning electron microscopy (SEM), field emission SEM, optical absorption and photoluminescence spectroscopy techniques. Subsequently, a wet chemistry procedure was performed to achieve ZnO NR growth. This methodology was conducive to the formation of rods of a relatively narrow distribution of diameters (60 - 70 nm) with lengths in the 1 - 3 μm range. Photoluminescence spectra were characterized by a dominant near-band-edge (NBE) peak followed by a green luminescence (GL) broad band, indicative of higher oxygen vacancy concentration in the ZnO NR grown on ZnO/ITO in comparison with those grown on ZnO/Si(100). A UV process was used for coating the ZnO NR with gold (Au). Au coating on ZnO NR was used to evaluate the detection capability by SERS of different analytes such as: 4-aminobenzenethiol (4-ABT) and 1,3,5-trinitroperhydro-1,3,5- triazine (RDX) at low levels. A strong SERS Raman spectrum was observed for 4-ABT. A limit of detection (LOD) of 1 × 10-8M for 4-ABT was achieved corresponding to a minimum of 5.4 × 105molecules detected under the experimental conditions at excitation wavelength of 785 nm with a sensitivity of the ZnO NR in the range of 1.1 × 10-16g under the laser spot.

Synthesis of ZnO nanorods and their optical absorption in visible-light region

Single crystalline ZnO nanorods were prepared by the hydrothermal method with synthesized ZnCl2·4Zn（OH）2 as the precursor. Morphologies of the nanorods were controlled by various reaction conditions with cetyltrimethylammonium bromide （CTAB） as the modifying agent. The nanorods were characterized by XRD, TEM, UV-Vis spectra, and IR spectra. The microstructure of holes in nanosize was observed on the surface of the nanorods. The UV-Vis spectra indicate that the as-prepared ZnO nanorods have absorption of visible-hght as well as ultraviolet-light. Therefore, these nanorods may be good candidates for visible-light photocatalysis materials from the viewpoint of practical applications. The reason for visible-light absorption was discussed in this article.

Photoluminescence and Structural Properties of ZnO Nanorods Growth by Assisted-Hydrothermal Method

Semiconducting zinc oxide (ZnO) nanorods were obtained in bulk quantity by an hexamethylenetetramine (HMTA)-assisted hydrothermal method at low temperature (90°C) with methenamine ((CH3)6N4 as surfactant and catalyst and zinc nitrate Zn(NO3)2·6H2O as Zn source. The structure and phase of ZnO nanorods were studied using x-ray diffraction (XRD) and high resolution transmission electron microscopy techniques (HRTEM). The morphology of the nanostructures was studied by scanning electron microscope (SEM) method. The photoluminescence (PL) properties were investigated founding two emission bands under UV excitation.