High-surface-area ZnO nanosheets are prepared using a template-assisted hydrothermal method.A saturation moment as high as 0.02 emu/g is obtained for the ZnO nanosheets.Both photoluminescence spectroscopy and x-ray ph...High-surface-area ZnO nanosheets are prepared using a template-assisted hydrothermal method.A saturation moment as high as 0.02 emu/g is obtained for the ZnO nanosheets.Both photoluminescence spectroscopy and x-ray photoelectron spectroscopy demonstrate the existence of abundant oxygen vacancies on the surfaces of the nanosheets.In addition,the oxygen vacancy concentration increases with an increasing nanosheet surface area.The results show that the origin of the room-temperature ferromagnetism is closely related with a large surface area and oxygen vacancies of the nanosheets.This finding suggests that the high-surface-area ZnO nanosheets are promising to be applied to spintronic devices.展开更多
In this experiment, Cu<sup>2+</sup> doped ZnO (Cu-ZnO) nanorods materials have been fabricated by hydrothermal method. Cu<sup>2+</sup> ions were doped into ZnO with ratios of 2, 5 and 7 mol.% (...In this experiment, Cu<sup>2+</sup> doped ZnO (Cu-ZnO) nanorods materials have been fabricated by hydrothermal method. Cu<sup>2+</sup> ions were doped into ZnO with ratios of 2, 5 and 7 mol.% (compared to the mole’s number of Zn<sup>2+</sup>). The hexamethylenetetramine (HMTA) solvent used for the fabrication of Cu-ZnO nanorods with the mole ratio of Zn<sup>2+</sup>:HMTA = 1:4. The characteristics of the materials were analyzed by techniques, such as XRD, Raman shift, SEM and UV-vis diffuse reflectance spectra (DRS). The photocatalytic properties of the materials were investigated by the decomposition of the methylene blue (MB) dye solution under ultraviolet light. The results show that the size of Cu-ZnO nanorods was reduced when the Cu<sup>2+</sup> doping ratio increased from 2 mol.% to 7 mol.%. The decomposition efficiency of the MB dye solution reached 92% - 97%, corresponding to the Cu<sup>2+</sup> doping ratio changed from 2 - 7 mol.% (after 40 minutes of ultraviolet irradiation). The highest efficiency for the decomposition of the MB solution was obtained at a Cu<sup>2+</sup> doping ratio of 2 mol.%.展开更多
ZnO single crystals were grown by the innovated hydrothermal method. The crystal surfaces were polished, and then studied by atom force microscope （AFM） and wet-chemical etching （WCE）. It was found that the Zn pol...ZnO single crystals were grown by the innovated hydrothermal method. The crystal surfaces were polished, and then studied by atom force microscope （AFM） and wet-chemical etching （WCE）. It was found that the Zn polar plane was smoother than O polar plane under the same polishing conditions. The etch pit density of Zn polar plane is 4.3×10^3 cm^-2, which is consistent with the previous report, while the density of etch pit of O polar plane is more than 103cm^-2. After annealing treatment, the density of etch pit of Zn plane reduces to 5.8×102 cm^2 and is superior to the current report. This investigation reveals that the high quality ZnO single crystals with fine Zn polar plane can be obtained by the innovated hydrothermal method.展开更多
Zinc oxide has a large energy gap and thus it has potential application in the field of solar cells by tuning the absorption of sunlight. In order to enhance its absorption of sunlight,dark color zinc oxides have been...Zinc oxide has a large energy gap and thus it has potential application in the field of solar cells by tuning the absorption of sunlight. In order to enhance its absorption of sunlight,dark color zinc oxides have been prepared by traditional hydrothermal method directly using a zinc foil as both source and substrate. We found that we could tune the optical properties of ZnO samples by changing the temperature. In particular, increasing temperature could significantly reduce the reflectivity of solar energy in the visible range. We speculate that the phenomenon is relevant to the sharp cone morphology of the ZnO nanorods grown on the surface of Zn foils, which furthermore enhance refraction and reflection of light in the nanorods. The capacity to improve the light absorption of ZnO may have a bright application in raising the efficiency of solar cells.展开更多
Zinc oxide (ZnO) nanorods have been synthesized by solution processing hydrothermal method in low temperature using the spin coating technique. Zinc acetate dehydrate, Zinc nitrate hexahydrate and hexamethylenetetrami...Zinc oxide (ZnO) nanorods have been synthesized by solution processing hydrothermal method in low temperature using the spin coating technique. Zinc acetate dehydrate, Zinc nitrate hexahydrate and hexamethylenetetramine were used as a starting material. The ZnO seed layer was first deposited by spin coated of ethanol zinc acetate dehydrate solution on a glass substrate. ZnO nanorods were grown on the ZnO seed layer from zinc nitrate hexahydrate and hexamethylene-tetramine solution, and their diameters, lengths were controlled by precursor concentration and development time. From UV-Visible spectrometry the optical band gap energy of ZnO nanorods was calculated to be 3.3 eV. The results of X-Ray Diffraction (XRD) showed the highly oriented nature of ZnO nanorods the hardest (002) peak reflects that c-axis elongated nanorods are oriented normal to the glass substrate. The Field Emission Scanning Electron Microscope (FESEM) was employed to measure both of average diameter of ZnO nanorods, Energy Dispersive X-Ray (EDX) is used to identify the elemental present and to determine the element composition in the samples.展开更多
Vertically oriented ZnO nanorods have been synthesized by hydrothermal method on quartz substrates with a seed layer. The influence of solution concentration on the morphology, structural and optical properties was an...Vertically oriented ZnO nanorods have been synthesized by hydrothermal method on quartz substrates with a seed layer. The influence of solution concentration on the morphology, structural and optical properties was analyzed. Results indicated that with the increase of solution concentration, the diameter and uniformity of ZnO nanorods increased. And the preferred orientation is obviously which shows better crystal quality. Typically, when the solution concentration is 0.03 mol/L, the nanorods exhibit a stronger UV emission peak located around 380 nm. In the visible region, all synthesized samples demonstrate more than 80% of optical transparency.展开更多
Semiconducting zinc oxide (ZnO) nanorods were obtained in bulk quantity by an hexamethylenetetramine (HMTA)-assisted hydrothermal method at low temperature (90°C) with methenamine ((CH3)6N4 as surfactant and cata...Semiconducting zinc oxide (ZnO) nanorods were obtained in bulk quantity by an hexamethylenetetramine (HMTA)-assisted hydrothermal method at low temperature (90°C) with methenamine ((CH3)6N4 as surfactant and catalyst and zinc nitrate Zn(NO3)2·6H2O as Zn source. The structure and phase of ZnO nanorods were studied using x-ray diffraction (XRD) and high resolution transmission electron microscopy techniques (HRTEM). The morphology of the nanostructures was studied by scanning electron microscope (SEM) method. The photoluminescence (PL) properties were investigated founding two emission bands under UV excitation.展开更多
A two-step method is adopted to synthesize Ag-doped ZnO nanorods. A ZnO seed layer is first prepared on a glass substrate by thermal decomposition of zinc acetate. Ag-doped ZnO nanorods are then assembled on the ZnO s...A two-step method is adopted to synthesize Ag-doped ZnO nanorods. A ZnO seed layer is first prepared on a glass substrate by thermal decomposition of zinc acetate. Ag-doped ZnO nanorods are then assembled on the ZnO seed layer using the hydrothermal method. The influences of the molar percentage of Ag ions to Zn ions （RAg/zn） on the structural and optical properties of the ZnO nanorods obtained are carefully studied using X-ray diffractometry, scanning electron microscopy and spectrophotometry. Results indicate that Ag ions enter into the crystal lattice through the substitution of Zn ions. The （002） c-axis-preferred orientation of the ZnO nanorods decreases as RAg/Zn increases. At RAg/Zn 〉 1.0%, ZnO nanorods lose their c-axis-preferred orientation and generate Ag precipitates from the ZnO crystal lattice. The average transmissivity in the visible region first increases and then decreases as RAg/Zn increases. The absorption edge is first blue shifted and then red shifted. The influence of Ag doping on the average head face, and axial dimensions of the ZnO nanorods may be optimized to improve the average transmissivity at RAg/Zn 〈 1.0%.展开更多
Eu-doped ZnO nanoneedles with different doping concentrations were prepared via the facile hydrothermal method.The crystal structure,morphology and photoluminescence property of the ZnO nanoneedles were characterized ...Eu-doped ZnO nanoneedles with different doping concentrations were prepared via the facile hydrothermal method.The crystal structure,morphology and photoluminescence property of the ZnO nanoneedles were characterized by X-ray diffraction（XRD）,scanning electron microscopy（SEM）,X-ray photoelectron spectroscopy（XPS）,photoluminescence spectroscopy（PL） and Raman spectroscopy.The results show that the europium ions are incorporated into the crystal lattice of ZnO matrix in trivalent ions.The nanoneedles are 2-3 μm in length and 100 nm in the tip diameter.PL and Raman measurements indicate that higher Eu^3＋ doping concentration may destroy the crystallization of the nanoneedles and decrease the ratio of IUV/IDLE,which is mainly due to the more defects in the doped ZnO nanoneedles.And the characteristic red emissions of Eu^3＋ ions are found by the PL spectroscopy with the Eu^3＋doping concentration increasing,which are attributed to the ^5D0→^7F0,^5D0→^7F1 and ^5D0→^7F2 transitions.展开更多
A new hydrothermal process--hydrothermal salt solution pressure-relief--was introduced, and ZnO powder with the size of 15 nm and ZnO fiber with length/diameter=16∶1 were prepared by this process. The change of parti...A new hydrothermal process--hydrothermal salt solution pressure-relief--was introduced, and ZnO powder with the size of 15 nm and ZnO fiber with length/diameter=16∶1 were prepared by this process. The change of particle size of ZnO powder and the formation mechanism of ZnO fiber were investigated. It is proposed that the main factor affecting the particle size of powders is nucleation rate, that is, the bigger the nucleation rate is, the smaller the particle is; the main factors affecting the formation of fiber include whether hydrothermal reaction proceeds under the condition of pressure-relief or not and the crystallization degree of powders before pressure-relief.展开更多
基金Supported by the National Key Research and Development Program of China under Grant No 2016YFA0201001the National Natural Science Foundation of China under Grant No 11574071+1 种基金the Natural Science Foundation for Outstanding Young Researcher in Hebei Province under Grant No E2016210093the Natural Science Foundation of Hebei Province under Grant No A2018210123
文摘High-surface-area ZnO nanosheets are prepared using a template-assisted hydrothermal method.A saturation moment as high as 0.02 emu/g is obtained for the ZnO nanosheets.Both photoluminescence spectroscopy and x-ray photoelectron spectroscopy demonstrate the existence of abundant oxygen vacancies on the surfaces of the nanosheets.In addition,the oxygen vacancy concentration increases with an increasing nanosheet surface area.The results show that the origin of the room-temperature ferromagnetism is closely related with a large surface area and oxygen vacancies of the nanosheets.This finding suggests that the high-surface-area ZnO nanosheets are promising to be applied to spintronic devices.
文摘In this experiment, Cu<sup>2+</sup> doped ZnO (Cu-ZnO) nanorods materials have been fabricated by hydrothermal method. Cu<sup>2+</sup> ions were doped into ZnO with ratios of 2, 5 and 7 mol.% (compared to the mole’s number of Zn<sup>2+</sup>). The hexamethylenetetramine (HMTA) solvent used for the fabrication of Cu-ZnO nanorods with the mole ratio of Zn<sup>2+</sup>:HMTA = 1:4. The characteristics of the materials were analyzed by techniques, such as XRD, Raman shift, SEM and UV-vis diffuse reflectance spectra (DRS). The photocatalytic properties of the materials were investigated by the decomposition of the methylene blue (MB) dye solution under ultraviolet light. The results show that the size of Cu-ZnO nanorods was reduced when the Cu<sup>2+</sup> doping ratio increased from 2 mol.% to 7 mol.%. The decomposition efficiency of the MB dye solution reached 92% - 97%, corresponding to the Cu<sup>2+</sup> doping ratio changed from 2 - 7 mol.% (after 40 minutes of ultraviolet irradiation). The highest efficiency for the decomposition of the MB solution was obtained at a Cu<sup>2+</sup> doping ratio of 2 mol.%.
基金Supported by the Knowledge Innovation Program of the Chinese Academy of SciencesSpecial Project on Science and Technology of Fujian Province (2005HZ1023)+4 种基金Knowledge Innovation Project of the Chinese Academy of Sciences (KJCX2.YW.W01)Outstanding Youth Fund (50625205)Youth Talent of Fujian Province (2006F3140)Fujian Engineering Research Center for Optoelectronic Materials (2007K02, 2005DC105003)the National Key Project of China for Basic Research (2007CB936703)
文摘ZnO single crystals were grown by the innovated hydrothermal method. The crystal surfaces were polished, and then studied by atom force microscope （AFM） and wet-chemical etching （WCE）. It was found that the Zn polar plane was smoother than O polar plane under the same polishing conditions. The etch pit density of Zn polar plane is 4.3×10^3 cm^-2, which is consistent with the previous report, while the density of etch pit of O polar plane is more than 103cm^-2. After annealing treatment, the density of etch pit of Zn plane reduces to 5.8×102 cm^2 and is superior to the current report. This investigation reveals that the high quality ZnO single crystals with fine Zn polar plane can be obtained by the innovated hydrothermal method.
基金supported by the National Natural Science Foundation of China(No.11575187)the National Key Research and Development Program(No.2016YFB0700205)
文摘Zinc oxide has a large energy gap and thus it has potential application in the field of solar cells by tuning the absorption of sunlight. In order to enhance its absorption of sunlight,dark color zinc oxides have been prepared by traditional hydrothermal method directly using a zinc foil as both source and substrate. We found that we could tune the optical properties of ZnO samples by changing the temperature. In particular, increasing temperature could significantly reduce the reflectivity of solar energy in the visible range. We speculate that the phenomenon is relevant to the sharp cone morphology of the ZnO nanorods grown on the surface of Zn foils, which furthermore enhance refraction and reflection of light in the nanorods. The capacity to improve the light absorption of ZnO may have a bright application in raising the efficiency of solar cells.
文摘Zinc oxide (ZnO) nanorods have been synthesized by solution processing hydrothermal method in low temperature using the spin coating technique. Zinc acetate dehydrate, Zinc nitrate hexahydrate and hexamethylenetetramine were used as a starting material. The ZnO seed layer was first deposited by spin coated of ethanol zinc acetate dehydrate solution on a glass substrate. ZnO nanorods were grown on the ZnO seed layer from zinc nitrate hexahydrate and hexamethylene-tetramine solution, and their diameters, lengths were controlled by precursor concentration and development time. From UV-Visible spectrometry the optical band gap energy of ZnO nanorods was calculated to be 3.3 eV. The results of X-Ray Diffraction (XRD) showed the highly oriented nature of ZnO nanorods the hardest (002) peak reflects that c-axis elongated nanorods are oriented normal to the glass substrate. The Field Emission Scanning Electron Microscope (FESEM) was employed to measure both of average diameter of ZnO nanorods, Energy Dispersive X-Ray (EDX) is used to identify the elemental present and to determine the element composition in the samples.
文摘Vertically oriented ZnO nanorods have been synthesized by hydrothermal method on quartz substrates with a seed layer. The influence of solution concentration on the morphology, structural and optical properties was analyzed. Results indicated that with the increase of solution concentration, the diameter and uniformity of ZnO nanorods increased. And the preferred orientation is obviously which shows better crystal quality. Typically, when the solution concentration is 0.03 mol/L, the nanorods exhibit a stronger UV emission peak located around 380 nm. In the visible region, all synthesized samples demonstrate more than 80% of optical transparency.
文摘Semiconducting zinc oxide (ZnO) nanorods were obtained in bulk quantity by an hexamethylenetetramine (HMTA)-assisted hydrothermal method at low temperature (90°C) with methenamine ((CH3)6N4 as surfactant and catalyst and zinc nitrate Zn(NO3)2·6H2O as Zn source. The structure and phase of ZnO nanorods were studied using x-ray diffraction (XRD) and high resolution transmission electron microscopy techniques (HRTEM). The morphology of the nanostructures was studied by scanning electron microscope (SEM) method. The photoluminescence (PL) properties were investigated founding two emission bands under UV excitation.
基金Projected supported by the National Natural Science Foundation of China (Grant No. 60807001)the Foundation of Henan Educational Committee,China (Grant No. 2010A140017)+1 种基金the Henan Provincial College Young Teachers Program,Chinathe Graduate Innovation of Zhengzhou University,China (Grant No. 11L10102)
文摘A two-step method is adopted to synthesize Ag-doped ZnO nanorods. A ZnO seed layer is first prepared on a glass substrate by thermal decomposition of zinc acetate. Ag-doped ZnO nanorods are then assembled on the ZnO seed layer using the hydrothermal method. The influences of the molar percentage of Ag ions to Zn ions （RAg/zn） on the structural and optical properties of the ZnO nanorods obtained are carefully studied using X-ray diffractometry, scanning electron microscopy and spectrophotometry. Results indicate that Ag ions enter into the crystal lattice through the substitution of Zn ions. The （002） c-axis-preferred orientation of the ZnO nanorods decreases as RAg/Zn increases. At RAg/Zn 〉 1.0%, ZnO nanorods lose their c-axis-preferred orientation and generate Ag precipitates from the ZnO crystal lattice. The average transmissivity in the visible region first increases and then decreases as RAg/Zn increases. The absorption edge is first blue shifted and then red shifted. The influence of Ag doping on the average head face, and axial dimensions of the ZnO nanorods may be optimized to improve the average transmissivity at RAg/Zn 〈 1.0%.
基金Supported by the National Natural Science Foundation of China（Nos.61178074, 61008051）, the Program for the Development of Science and Technology of Jilin Province, China（Nos.20100113, 20140101205 JC） and the Natural Science Foundation of Jiangsu Province, China（No.BK2011513）.
文摘Eu-doped ZnO nanoneedles with different doping concentrations were prepared via the facile hydrothermal method.The crystal structure,morphology and photoluminescence property of the ZnO nanoneedles were characterized by X-ray diffraction（XRD）,scanning electron microscopy（SEM）,X-ray photoelectron spectroscopy（XPS）,photoluminescence spectroscopy（PL） and Raman spectroscopy.The results show that the europium ions are incorporated into the crystal lattice of ZnO matrix in trivalent ions.The nanoneedles are 2-3 μm in length and 100 nm in the tip diameter.PL and Raman measurements indicate that higher Eu^3＋ doping concentration may destroy the crystallization of the nanoneedles and decrease the ratio of IUV/IDLE,which is mainly due to the more defects in the doped ZnO nanoneedles.And the characteristic red emissions of Eu^3＋ ions are found by the PL spectroscopy with the Eu^3＋doping concentration increasing,which are attributed to the ^5D0→^7F0,^5D0→^7F1 and ^5D0→^7F2 transitions.
文摘A new hydrothermal process--hydrothermal salt solution pressure-relief--was introduced, and ZnO powder with the size of 15 nm and ZnO fiber with length/diameter=16∶1 were prepared by this process. The change of particle size of ZnO powder and the formation mechanism of ZnO fiber were investigated. It is proposed that the main factor affecting the particle size of powders is nucleation rate, that is, the bigger the nucleation rate is, the smaller the particle is; the main factors affecting the formation of fiber include whether hydrothermal reaction proceeds under the condition of pressure-relief or not and the crystallization degree of powders before pressure-relief.
