First-principles study and electronic structures of Mn-doped ultrathin ZnO nanofilms

The first-principles density functional calculation is used to investigate the electronic structures and magnetic properties of Mn-doped and N-co-doped ZnO nanofilms.The band structure calculation shows that the band gaps of ZnO films with 2,4,and 6 layers are larger than the band gap of the bulk with wurtzite structure and decrease with the increase of film thickness.However,the four-layer ZnO nanofilms exhibit ferromagnetic phases for Mn concentrations less than 24% and 12% for Mn-doping performed in the whole layers and two layers of the film respectively,while they exhibit spin glass phases for higher Mn concentrations.It is also found,on the one hand,that the spin glass phase turns into the ferromagnetic one,with the substitution of nitrogen atoms for oxygen atoms,for nitrogen concentrations higher than 16% and 5% for Mn-doping performed in the whole layers and two layers of the film respectively.On the other hand,the spin-glass state is more stable for ZnO bulk containing 5% of Mn impurities,while the ferromagnetic phase is stable by introducing the p-type carriers into the bulk system.Moreover,it is shown that using the effective field theory for ferromagnetic system,the Curie temperature is close to the room temperature for the undamped Ruderman-Kittel-Kasuya-Yoshida（RKKY） interaction.

Crystallization Behavior and Properties of B-Doped ZnO Thin Films Prepared by Sol-Gel Method with Different Pyrolysis Temperatures

Boron-doped zinc oxide transparent （BZO） films were prepared by sol-gel method. The effect of pyrolysis temperature on the crystallization behavior and properties was systematically investigated. XRD patterns revealed that the BZO films had wurtzite structure with a preferential growth orientation along the c-axis. With the increase of pyrolysis temperature, the particle size and surface roughness of the BZO films increased, suggesting that pyrolysis temperature is the critical factor for determining the crystallization behavior of the BZO films. Moreover, the carrier concentration and the carrier mobility increased with increasing the pyrolysis temperature, and the mean transmittance for every film is over 90% in the visible range.

Effects of high-dose Ge ion implantation and post-implantation annealing on ZnO thin films

This paper reports that ion implantation to a dose of 1 ×10^17 ions/cm^2 was performed on c-axis-orientated ZnO thin films deposited on （0001） sapphire substrates by the sol-gel technique. After ion implantation, the as-implanted ZnO films were annealed in argon ambient at different temperatures from 600 - 900 ℃. The effects of ion implantation and post-implantation annealing on the structural and optical properties of the ZnO films were investigated by x-ray diffraction （XRD）, photoluminescence （PL）. It was found that the intensities of （002） peak and near band edge （NBE） exitonic ultraviolet emission increased with increasing annealing temperature from 600- 900 ℃. The defect related deep level emission （DLE） firstly increased with increasing annealing temperature from 600 - 750 ℃, and then decreased quickly with increasing annealing temperature. The recovery of the intensities of NBE and DLE occurs at ～850℃ and ～750℃ respectively. The relative PL intensity ratio of NBE to DLE showed that the quality of ZnO films increased continuously with increasing annealing temperature from 600 - 900 ℃.

Properties of doped ZnO transparent conductive thin films deposited by RF magnetron sputtering using a series of high quality ceramic targets

To obtain high transmittance and low resistivity ZnO transparent conductive thin films,a series of ZnO ceramic targets（ZnO：Al,ZnO：（Al,Dy）,ZnO：（Al,Gd）,ZnO：（Al,Zr）,ZnO：（Al,Nb）,and ZnO：（Al,W）） were fabricated and used to deposit thin films onto glass substrates by radio frequency（RF） magnetron sputtering.X-ray diffraction（XRD） analysis shows that the films are polycrystalline fitting well with hexagonal wurtzite structure and have a preferred orientation of the（002） plane.The transmittance of above 86% as well as the lowest resistivity of 8.43 × 10^-3 Ω·cm was obtained.

Effect of annealing temperature on the microstructure and optoelectrical properties of ZnO thin films and their application in self-powered accelerometers

This paper reports a piezoelectric nanogenerator(NG) with a thickness of approximately 80 μm for miniaturized self-powered acceleration sensors. To deposit the piezoelectric zinc oxide(ZnO) thin film, a magnetron sputtering machine was used. Polymethyl methacrylate(PMMA) and aluminum-doped zinc oxide(AZO) were used as the insulating layer and the top electrode of the NG, respectively. The experimental results show that the ZnO thin films annealed at 150℃ exhibited the highest crystallinity among the prepared films and an optical band gap of 3.24 eV. The NG fabricated with an AZO/PMMA/ZnO/stainless steel configuration exhibited a higher output voltage than the device with an AZO/ZnO/PMMA/stainless steel configuration. In addition, the annealing temperature affected the open-circuit voltage of the NGs;the output voltage reached 3.81 V when the annealing temperature was 150℃. The open-circuit voltage of the prepared self-powered accelerometer increased linearly with acceleration. In addition, the small NG-based accelerometer, which exhibited excellent fatigue resistance, can be used for acceleration measurements of small and lightweight devices.

Induced growth of high quality ZnO thin films by crystallized amorphous ZnO

This paper reports the induced growth of high quality ZnO thin film by crystallized amorphous ZnO. Firstly amorphous ZnO was prepared by solid-state pyrolytic reaction, then by taking crystallized amorphous ZnO as seeds （buffer layer）, ZnO thin films have been grown in diethyene glycol solution of zinc acetate at 80 ℃. X-ray Diffraction curve indicates that the films were preferentially oriented [001] out-of-plane direction of the ZnO. Atomic force microscopy and scanning electron microscopy were used to evaluate the surface morphology of the ZnO thin film. Photoluminescence spectrum exhibits a strong ultraviolet emission while the visible emission is very weak. The results indicate that high quality ZnO thin film was obtained.

Improved Electrochemical Performance of Mg-doped ZnO Thin Film as Anode Material for Lithium Ion Batteries

Zn1-xMgxO （x = 0, 0.18） thin films were fabricated on the copper substrates by radiofrequency magnetron sputtering using the high pure argon as a sputtering gas. The Zn1-xMgxO films were characterized by X-ray powder diffraction （XRD）, scanning electron microscope （SEM） and galvanostatic tests. The electrochemical test showed an improved electrochemical performance of Zn0.82EMg0.18O thin film as an anode material for lithium ion batteries.

The effects of post-thermal annealing on the optical parameters of indium-doped ZnO thin films

Indium-doped ZnO thin films are deposited on quartz glass slides by RF magnetron sputtering at ambient temperature. The as-deposited films are annealed at different temperatures from 400℃ to 800 ℃ in air for 1 h. Transmittance spectra are used to determine the optical parameters and the thicknesses of the films before and after annealing using a nonlinear programming method, and the effects of the annealing temperatures on the optical parameters and the thickness are investigated. The optical band gap is determined from the absorption coefficient. The calculated results show that the film thickness and optical parameters both increase first and then decrease with increasing annealing temperature from 400℃ to 800℃. The band gap of the as-deposited ZnO：In thin film is 3.28 eV, and it decreases to 3.17 eV after annealing at 400℃. Then the band gap increases from 3.17 eV to 3.23 eV with increasing annealing temperature from 400℃ to 800℃.

Angle-sensitive and fast photovoltage of silver nanocluster embeded ZnO thin films induced by 1.064-μm pulsed laser

Silver nanocluster embedded ZnO composite thin film was observed to have an angle-sensitive and fast photovoltaic effect in the angle range from -90° to 90° , its peak value and the polarity varied regularly with the angle of incidence of the 1.064-μm pulsed Nd：YAG laser radiation onto the ZnO surface. Meanwhile, for each photovoltaic signal, its rising time reached -2 ns with an open-circuit photovoltage of -2 ns full width at half-maximum. This angle-sensitive fast photovoltaic effect is expected to put this composite film a candidate for angle-sensitive and fast photodetector.

Simulation of grain boundary effect on characteristics of ZnO thin film transistor by considering the location and orientation of grain boundary

The grain boundaries （GBs） have a strong effect on the electric properties of ZnO thin film transistors （TFTs）. A novel grain boundary model was developed to analyse the effect. The model was characterized with different angles between the orientation of the grain boundary and the channel direction. The potential barriers formed by the grain boundaries increase with the increase of the grain boundary angle, so the degradation of the transistor characteristics increases. When a grain boundary is close to the drain edge, the potential barrier height reduces, so the electric properties were improved.

Facile fabrication of heterostructure with p-BiOCl nanoflakes and n-ZnO thin film for UV photodetectors

Herein, high-quality n-ZnO film layer on c-sapphire and well-crystallized tetragonal p-BiOCl nanoflakes on Cu foil are prepared, respectively. According to the absorption spectra, the bandgaps of n-ZnO and p-BiOCl are confirmed as ~3.3 and~3.5 eV, respectively. Subsequently, a p-BiOCl/n-ZnO heterostructural photodetector is constructed after a facile mechanical bonding and post annealing process. At –5 V bias, the photocurrent of the device under 350 nm irradiation is ~800 times higher than that in dark, which indicates its strong UV light response characteristic. However, the on/off ratio of In–ZnO–In photodetector is ~20 and the Cu–BiOCl–Cu photodetector depicts very weak UV light response. The heterostructure device also shows a short decay time of 0.95 s, which is much shorter than those of the devices fabricated from pure ZnO thin film and BiOCl nanoflakes. The p-BiOCl/n-ZnO heterojunction photodetector provides a promising pathway to multifunctional UV photodetectors with fast response, high signal-to-noise ratio, and high selectivity.

Photoluminescence properties of ZnO thin films prepared by DC magnetron sputtering

ZnO thin films were prepared by direct current(DC)reactive magnetron sputtering under different oxygen partial pressures.And then the samples were annealed in vacuum at 450℃.The effects of the oxygen partial pressures and the treatment of annealing in vacuum on the photoluminescence and the concentration of six intrinsic defects in ZnO thin films such as oxygen vacancy(VO),zinc vacancy(VZn),antisite oxygen(OZn),antisite zinc(ZnO),interstitial oxygen(Oi)and interstitial zinc(Zni)were studied.The results show that a green photoluminescence peak at 520 nm can be observed in all the samples,whose intensity increases with increasing oxygen partial pressure;for the sample annealed in vacuum,the intensity of the green peak increases as well.The green photoluminescence peak observed in ZnO may be attributed to zinc vacancy,which probably originates from transitions between electrons in the conduction band and zinc vacancy levels,or from transitions between electrons in zinc vacancy levels and up valence band.

Structure distortion, optical and electrical properties of ZnO thin films co-doped with Al and Sb by sol-gel spin coating

ZnO thin films co-doped with A1 and Sb with different concentrations and a fixed molar ratio of AlCl3 to SbCl3 at 1：2, are prepared by a sol-gel spin-coating method on glass annealed at 550 ℃ for 2 h in air. The x-ray diffraction results confirm that the ZnO thin films co-doped with Al distortion, and the biaxial stresses are 1.03× 10^8. 3.26× 10^8 and Sb are of wurtzite hexagonal ZnO with a very small 5.23 × 10^8, and 6.97× 10^8 Pa, corresponding to those of the ZnO thin films co-doped with Al and Sb in concentrations of 1.5, 3.0, 4.5, 6.0 at% respectively. The optical properties reveal that the ZnO thin films co-doped with Al and Sb have obviously enhanced transmittance in the visible region. The electrical properties show that ZnO thin film co-doped with Al and Sb in a concentration of 1.5 at% has a lowest resistivity of 2.5 Ω·cm.

Surface morphology and photoluminescence properties of ZnO thin films obtained by PLD

ZnO thin films on Si(111) substrate were deposited by laser ablation of Zn target in oxygen reactive atmosphere, Nd-YAG laser with wavelength of 1 064 nm was used as laser source. XRD and FESEM microscopy were applied to characterize the structure and surface morphology of the deposited ZnO films. The optical properties of the ZnO thin films were characterized by photoluminescence. The UV and deep level (yellow-green) light were observed from the films. The UV light is the intrinsic property and deep level light is attributed to the existence of antisite defects (OZn). The intensity of UV and deep level light depends strongly on the surface morphology and is explained by the surface roughness of ZnO film. A strongly UV emission can be obtained from ZnO film with surface roughness in nanometer range.

Synthesis Sol-Gel Derived Highly Transparent ZnO Thin Films for Optoelectronic Applications

In this work, ZnO thin films were derived by sol-gel using two different techniques;dip coating and spin coating technique. The films were deposited onto glass substrate at room temperature using sol-gel composed from zinc acetate dehydrate, monoethanolamine, isopropanole, and de-ionized water, the films were preheated at 225?C for 15 min. The crystallographic structures of ZnO films were investigated using X-ray diffraction (XRD);the result shows that the good film was prepared at dip coating technique, it was polycrystalline and highly c-orientation along (002) plane, the lattice constant ratio (c/a) was calculated at (002), it was about 1.56. The structure of thin films, prepared by spin coating technique, was amorphous with low intensity and wide peaks. The optical properties of the prepared film were studied using UV-VIS spectrophotometer with the range 190 - 850 nm, and by using the fluorescence spectrometer. The optical characterization of ZnO thin films that were prepared by the dip coating method have good transmittance of about 92% in the visible region, it can be noted from the fluorescence spectrometer two broad visible emission bands centered at 380nm and 430 nm. The optical energy gaps for the direct and indirect allowed transitions were calculated, the values were equal 3.2 eV and 3.1 eV respectively. Dip coating technique create ZnO films with potential for application as transparent electrodes in optoelectronic devices such as solar cell.

Effect of Substrates on the Properties of ZnO Thin Films Grown by Pulsed Laser Deposition

Polycrystalline zinc oxide (ZnO) thin films have been deposited at 450°C onto glass and silicon substrates by pulsed laser deposition technique (PLD). The used source was a KrF excimer laser (248 nm, 25 ns, 5 Hz, 2 J/cm2). The effects of glass and silicon substrates on structural and optical properties of ZnO films have been investigated. X-ray diffraction patterns showed that ZnO films are polycrystalline with a hexagonal wurtzite—type structure with a strong (103) orientation and have a good crystallinity on monocrystalline Si(100) substrate. The thickness and compositional depth profile were studied by Rutherford Backscattering spectrometry (RBS). The average transmittance of ZnO films deposited on glass substrate in the visible range is 70%.

Structural, Optical and Luminescence Properties of ZnO Thin Films Prepared by Sol-Gel Spin-Coating Method： Effect of Precursor Concentration

Transparent zinc oxide（ZnO） thin films are fabricated by a simple sol-gel spin-coating technique on glass substrates with different solution concentrations（0.3-1.2 M） using zinc acetate dehydrate [Zn（CH_3COO）_2·2H_2O] as precursor and isopropanol and monoethanolamine（MEA） as solvent and stabilizer, respectively. The molar ratio of zinc acetate dehydrate to MEA is 1.0. X-ray diffraction, ultraviolet-visible spectroscopy and photoluminescence spectroscopy are employed to investigate the effect of solution concentration on the structural and optical properties of the ZnO thin films. The obtained results of all thin films are discussed in detail and are compared with other experimental data.

High-Performance Photo-Modulated Thin-Film Transistor Based on Quantum dots/Reduced Graphene Oxide Fragment-Decorated ZnO Nanowires

In this paper, a photo-modulated transistor based on the thin-film transistor structure was fabricated on the flexible substrate by spin-coating and magnetron sputtering. A novel hybrid material that composed of Cd Se quantum dots and reduced graphene oxide(RGO) fragment-decorated ZnO nanowires was synthesized to overcome the narrow optical sensitive waveband and enhance the photo-responsivity. Due to the enrichment of the interface and heterostructure by RGO fragments being utilized, the photo-responsivity of the transistor was improved to 2000 AW^(-1) and the photo-sensitive wavelength was extended from ultraviolet to visible. In addition, a positive back-gate voltage was employed to reduce the Schottky barrier width of RGO fragments and ZnO nanowires. As a result, the amount of carriers was increased by 10 folds via the modulation of back-gate voltage. With these inherent properties, such as integrated circuit capability and wide optical sensitive waveband, the transistor will manifest great potential in the future applications in photodetectors.

Fabrication of 2D ZnO Nanosheet Thin Film by a Simple Two-Step Approach

In this paper,2D single-crystalline ZnO nanosheets thin film was fabricated successfully on silicon wafer by a simple two-step approach.XRD,SEM and TEM were used to characterize the phase structures and morphologies of ZnO nanosheets film.

Physical Properties of Al-doped ZnO and Ga-doped ZnO Thin Films Prepared by Direct Current Sputtering at Room Temperature

Al-doped zinc oxide（AZO） and Ga-doped zinc oxide（GZO） thin films with the same doping concentration（3.6 at%） were deposited on glass substrates at room temperature by direct current（DC） magnetron sputtering.Consequently,we comparatively studied the doped thin films on the basis of their structural,morphological,electrical,and optical properties for optoelectronic applications.Both thin films exhibited excellent optical properties with more than 85%transmission in the visible range.The GZO thin film had better crystallinity and smoother surface morphology than the AZO thin film.The conductivity of the GZO thin film was improved compared to that of the AZO thin film：the resistivity decreased from 1.01×10^-3 to 3.5×10^-4 Ω cm,which was mostly due to the increase of the carrier concentration from 6.5×10^20 to 1.46×10^21cm^-3.These results revealed that the GZO thin film had higher quality than the AZO thin film with the same doping concentration for optoelectronic applications.