Fe复合ZnO催化剂制备及其光催化固氮性能研究

本文以ZnSO4·7H2O与FeSO4·7H2O为原料采用沉淀还原法制备了不同含量Fe复合ZnO催化剂。通过X射线衍射仪(XRD)、紫外–可见漫反射(UV-Vis)和电化学组抗图、肖特基等表征手段对催化剂的物相、吸光特性、光生电子电阻和移动性能等进行了研究。研究结果发现随Fe含量的增加,复合ZnO催化剂光吸收强度逐渐增加,能带间隙逐渐减小,光生电子转移阻力减小,移动速度增加,光生电子空穴发生复合率降低,越容易活化氮分子与氢离子生成铵离子,复合ZnO催化剂光催化固氮性能逐渐升高。当Zn与Fe物质的量比为4:6,干燥温度为90℃时,制备的Fe复合ZnO催化剂固氮性能最好,NH4 浓度达到了12.8175 μg·gcat−1。

Crystallization Behavior and Properties of B-Doped ZnO Thin Films Prepared by Sol-Gel Method with Different Pyrolysis Temperatures

Boron-doped zinc oxide transparent （BZO） films were prepared by sol-gel method. The effect of pyrolysis temperature on the crystallization behavior and properties was systematically investigated. XRD patterns revealed that the BZO films had wurtzite structure with a preferential growth orientation along the c-axis. With the increase of pyrolysis temperature, the particle size and surface roughness of the BZO films increased, suggesting that pyrolysis temperature is the critical factor for determining the crystallization behavior of the BZO films. Moreover, the carrier concentration and the carrier mobility increased with increasing the pyrolysis temperature, and the mean transmittance for every film is over 90% in the visible range.

Effects of high-dose Ge ion implantation and post-implantation annealing on ZnO thin films

This paper reports that ion implantation to a dose of 1 ×10^17 ions/cm^2 was performed on c-axis-orientated ZnO thin films deposited on （0001） sapphire substrates by the sol-gel technique. After ion implantation, the as-implanted ZnO films were annealed in argon ambient at different temperatures from 600 - 900 ℃. The effects of ion implantation and post-implantation annealing on the structural and optical properties of the ZnO films were investigated by x-ray diffraction （XRD）, photoluminescence （PL）. It was found that the intensities of （002） peak and near band edge （NBE） exitonic ultraviolet emission increased with increasing annealing temperature from 600- 900 ℃. The defect related deep level emission （DLE） firstly increased with increasing annealing temperature from 600 - 750 ℃, and then decreased quickly with increasing annealing temperature. The recovery of the intensities of NBE and DLE occurs at ～850℃ and ～750℃ respectively. The relative PL intensity ratio of NBE to DLE showed that the quality of ZnO films increased continuously with increasing annealing temperature from 600 - 900 ℃.

Effect of defect complex on magnetic properties of (Fe, Mn)-doped ZnO thin films

We have observed room temperature ferromagnetism in Mn-doped and (Fe, Mn)-codoped ZnO thin films grown under different oxygen partial pressures by pulsed laser deposition. The X-ray diffraction and optical transmission spectra studies demonstrate the natural incorporation of Fe and Mn cations into wurtzite ZnO lattices. The effects of transition metal doping and defects on the magnetic properties was investigated. It is found that room temperature ferromagnetism is sensitive to oxygen vacancy and Zn vacancy. The absence of ferromagnetism in pure ZnO films grown under different oxygen partial pressures reveals that the transition metal ions should also play an important role in inducing the ferromagnetism.

Effect of annealing temperature on the microstructure and optoelectrical properties of ZnO thin films and their application in self-powered accelerometers

This paper reports a piezoelectric nanogenerator(NG) with a thickness of approximately 80 μm for miniaturized self-powered acceleration sensors. To deposit the piezoelectric zinc oxide(ZnO) thin film, a magnetron sputtering machine was used. Polymethyl methacrylate(PMMA) and aluminum-doped zinc oxide(AZO) were used as the insulating layer and the top electrode of the NG, respectively. The experimental results show that the ZnO thin films annealed at 150℃ exhibited the highest crystallinity among the prepared films and an optical band gap of 3.24 eV. The NG fabricated with an AZO/PMMA/ZnO/stainless steel configuration exhibited a higher output voltage than the device with an AZO/ZnO/PMMA/stainless steel configuration. In addition, the annealing temperature affected the open-circuit voltage of the NGs;the output voltage reached 3.81 V when the annealing temperature was 150℃. The open-circuit voltage of the prepared self-powered accelerometer increased linearly with acceleration. In addition, the small NG-based accelerometer, which exhibited excellent fatigue resistance, can be used for acceleration measurements of small and lightweight devices.

The effects of post-thermal annealing on the optical parameters of indium-doped ZnO thin films

Indium-doped ZnO thin films are deposited on quartz glass slides by RF magnetron sputtering at ambient temperature. The as-deposited films are annealed at different temperatures from 400℃ to 800 ℃ in air for 1 h. Transmittance spectra are used to determine the optical parameters and the thicknesses of the films before and after annealing using a nonlinear programming method, and the effects of the annealing temperatures on the optical parameters and the thickness are investigated. The optical band gap is determined from the absorption coefficient. The calculated results show that the film thickness and optical parameters both increase first and then decrease with increasing annealing temperature from 400℃ to 800℃. The band gap of the as-deposited ZnO：In thin film is 3.28 eV, and it decreases to 3.17 eV after annealing at 400℃. Then the band gap increases from 3.17 eV to 3.23 eV with increasing annealing temperature from 400℃ to 800℃.

Simulation of grain boundary effect on characteristics of ZnO thin film transistor by considering the location and orientation of grain boundary

The grain boundaries （GBs） have a strong effect on the electric properties of ZnO thin film transistors （TFTs）. A novel grain boundary model was developed to analyse the effect. The model was characterized with different angles between the orientation of the grain boundary and the channel direction. The potential barriers formed by the grain boundaries increase with the increase of the grain boundary angle, so the degradation of the transistor characteristics increases. When a grain boundary is close to the drain edge, the potential barrier height reduces, so the electric properties were improved.

Effect of Substrates on the Properties of ZnO Thin Films Grown by Pulsed Laser Deposition

Polycrystalline zinc oxide (ZnO) thin films have been deposited at 450°C onto glass and silicon substrates by pulsed laser deposition technique (PLD). The used source was a KrF excimer laser (248 nm, 25 ns, 5 Hz, 2 J/cm2). The effects of glass and silicon substrates on structural and optical properties of ZnO films have been investigated. X-ray diffraction patterns showed that ZnO films are polycrystalline with a hexagonal wurtzite—type structure with a strong (103) orientation and have a good crystallinity on monocrystalline Si(100) substrate. The thickness and compositional depth profile were studied by Rutherford Backscattering spectrometry (RBS). The average transmittance of ZnO films deposited on glass substrate in the visible range is 70%.

Structural, Optical and Luminescence Properties of ZnO Thin Films Prepared by Sol-Gel Spin-Coating Method： Effect of Precursor Concentration

Transparent zinc oxide（ZnO） thin films are fabricated by a simple sol-gel spin-coating technique on glass substrates with different solution concentrations（0.3-1.2 M） using zinc acetate dehydrate [Zn（CH_3COO）_2·2H_2O] as precursor and isopropanol and monoethanolamine（MEA） as solvent and stabilizer, respectively. The molar ratio of zinc acetate dehydrate to MEA is 1.0. X-ray diffraction, ultraviolet-visible spectroscopy and photoluminescence spectroscopy are employed to investigate the effect of solution concentration on the structural and optical properties of the ZnO thin films. The obtained results of all thin films are discussed in detail and are compared with other experimental data.

Influence of reducing anneal on the ferromagnetism in single crystalline Co-doped ZnO thin films

This paper reports that the high-quality Co-doped ZnO single crystalline films have been grown on a-plane sapphire substrates by using molecular-beam epitaxy. The as-grown films show high resistivity and non-ferromagnetism at room temperature, while they become more conductive and ferromagnetic after annealing in the reducing atmosphere either in the presence or absence of Zn vapour. The x-ray absorption studies indicate that all Co ions in these samples actually substituted into the ZnO lattice without formatting any detectable secondary phase. Compared with weak ferromagnetism （0.16 μB/Co2＋） in the Zno.95 Co0.05 O single crystalline film with reducing annealing in the absence of Zn vapour, the films annealed in the reducing atmosphere with Zn vapour are found to have much stronger ferromagnetism （0.65 μB/Co2＋） at room temperature. This experimental studies clearly indicate that Zn interstitials are more effective than oxygen vacancies to activate the high-temperature ferromagnetism in Co-doped ZnO films, and the corresponding ferromagnetic mechanism is discussed.

Structural and optical characteristic features of RF sputtered CdS/ZnO thin films

In this study,CdS/ZnO(2:3 mol%)thin films are successfully deposited on quartz substrates by using the sputtering technique.Good images on the structural and optical characteristic features of CdS/ZnO thin films before and after annealing are obtained.The CdS/ZnO thin films are annealed respectively at temperatures of 373 K,473 K,and 573 K and the structural features are examined by XRD,ATR-FTIR,and FESEM.The optical properties of CdS/ZnO thin films such as refractive indices,absorption coefficients,optical band gap energy values,Urbach energy values,lattice dielectric constants,and high frequency dielectric constants are determined from spectrophotometer data recorded over the spectral range of 300 nm-2500 nm.Dispersion parameters are investigated by using a single-oscillator model.Photoluminescence spectra of CdS/ZnO thin films show an overall decrease in their intensity peaks after annealing.The third-order nonlinear optical parameter,and nonlinear refractive index are also estimated.

Effect of Sn Doping on the Properties of ZnO Thin Films Prepared by Spray Pyrolysis

Layers of transparent and conductive Sn-doped zinc oxide (ZnO) have been prepared using chemical reactive liquid phase (spray) method on glass substrates. X-ray diffraction analysis shows that the obtained layers show preferential grains orientation along the direction (002). Microstructural analysis indicates that the thickness of the deposited films is independent of Sn content, i.e. 408 nm, and that the average grain size increases with increasing Sn content, ranging from 31 nm to 42 nm. The value of the optical gap obtained using UV-visible transmission spectroscopy method increases slightly from 3.1 eV to 3.3 eV. Moreover, transmission curves reveal that the prepared thin films are transparent in the visible domain.

The Effect of ZnO Thin Film and Its Structural and Optical Properties Prepared by Sol-Gel Spin Coating Method

ZnO thin films were deposited on glass substrates at different Zinc concentration and their effects on structural, Morphology and optical properties were investigated. Zinc acetate dehydrate, 2 Methoxy ethanol and Monoethanolamine were used as the precursor, solvent and stabilizer respectively. The molar ratio of Monoethanolamine to Zinc acetate was maintained as 1. The crystal structure and orientation of the films were analyzed by XRD. The XRD patterns show that the ZnO films are polycrystalline with wurtzite hexagonal structure. The film with 0.5 m/l concentration has the better crystallinity. The thickness of the films was determined by thickness Profilometer. The surface morphology of the films was observed by Scanning electron microscope. The SEM images show that they are homogeneous, continuous and spindle like shape. The optical properties of the films were studied by UV-Vis-Spectrophotometer. The transmittance of the films decreases with increase of Zinc concentration. The energy band gap of the films decreases slightly, when the Zinc concentration increases from0.25 m/l to0.75 m/l and then increases when the concentration further increases from0.75 m/l to1.0 m/l.

Effects of Annealing Temperature on Properties of ZnO Thin Films Grown by Pulsed Laser Deposition

ZnO thin films are deposited on n-Si（111） substrates by pulsed laser deposition（PLD） system. Then the samples are annealed at different temperatures in air ambient and their properties are investigated particularly as a function of annealing temperature. The microstructure, morphology and optical properties of the as-grown ZnO films are studied by X-ray diffraetion（XRD）. atomic force mieroseope（AFM）, Fourier transform infrared spectroscopy（FTIR） and photoluminescence（PL） spectra. The results show that the as- grown ZnO films have a hexagonal wurtzite structure with a preferred c-axis orientation. Moreover, the diameters of the ZnO crystallites become larger and the crystal quality of the ZnO fihns is improved with the increase of annealing temperature.

基于共溅射ZnO/SnO_(2)异质结薄膜的气体传感器研究

采用射频磁控共溅射法在叉指电极上制备了ZnO/SnO_(2)n-n异质结复合薄膜,系统测试了其气敏特性,并分析了其气敏机理。结果表明,与ZnO薄膜和SnO_(2)薄膜气体传感器相比,ZnO/SnO_(2)异质结薄膜气体传感器具有更低的工作温度、更高的灵敏度以及更快的响应和恢复速度。ZnO/SnO_(2)异质结薄膜气体传感器对乙醇具有较好的选择性,最低检测体积分数为1×10^(-6),最佳工作温度为250℃;对1×10^(-4)乙醇气体的灵敏度可达18.4,响应时间和恢复时间分别为10 s和19 s。

Effect of sputtering conditions on growth and properties of ZnO :Al films

Al-doped zinc oxide（AZO） films were deposited on glass substrates by mid-frequency magnetron sputtering. The effects of substrate rotation speed and target-substrate distance on the electrical, optical properties and microstructure and crystal structures of the resulting films were investigated by scanning electron microscopy（SEM）, atomic force microscopy（AFM）, X-ray diffraction（XRD）, spectrophotometer and Hall-effect measurement system, respectively. XRD results show that all AZO films exhibit a strong preferred c-axis orientation. However, the crystallinity of films decreases with the increase of substrate rotation speed, accompanying with the unbalanced grains grows. For the films prepared at different target-substrate distances, the uniform microstructure and morphology are observed. The highest carrier concentration of 5.9×1020 cm-3 and Hall mobility of 13.1 cm^2/（V·s） are obtained at substrate rotation speed of 0 and target-substrate distance of 7 cm. The results indicate that the structure and performances of the AZO films are strongly affected by substrate rotation speed.

双层结构对ZnO TFT稳定性的影响

室温下采用射频磁控溅射方法在SiO_(2)/Si衬底上沉积了单层ZnO薄膜和高氧/低氧双层ZnO薄膜,采用电子束蒸发设备蒸镀Al电极,制备单沟道ZnO TFTs和双层沟道ZnO TFTs。比较两种结构ZnO TFTs的各种性能参数,分析双层结构对TFTs产生的影响。实验结果表明,底部高含氧量ZnO层和顶部低含氧量ZnO层构成了DAL同质结且高氧/低氧薄膜存在载流子浓度产差,利用载流子从高浓度向低浓度扩散的性质,可以填补栅介电层和沟道层之间的界面态缺陷,使器件界面类受主陷阱减少,有效降低TFTs的滞回现象。与单有源层TFTs相比,双沟道层TFTs还具有电学调制作用,其电学性能和稳定性均有明显的提高,得到最佳TFTs的开/关电流比达到3.44×10^(9),亚阈值摆幅为0.68 V/dec,阈值电压偏移为1.2 V。

电化学沉积法制备ZnO厚膜工艺研究

X射线具有较高的光子能量,这使得其在ZnO材料中具有大的穿透深度,因此为了更有效地探测X射线,需要制备出微米甚至百微米厚度的ZnO膜。本文采用电化学沉积法快速制备14.85μm厚的ZnO膜。实验结果表明,沉积电势和电极材料会显著影响ZnO膜的沉积速率与表面形貌。随着沉积电势的升高,ZnO形貌由六角柱状结构变为片状结构,当电势过大时会有大量氢气生成,导致薄膜孔洞增加而无法成膜。使用金属Pt为阳极电极时,溶液会逐渐酸化,导致ZnO在沉积的同时也会溶解,当二者速率相一致时,ZnO膜厚便不再增加,因此不适合生长ZnO厚膜。而使用金属Zn为阳极电极时,溶液的pH值基本保持不变,更适合生长ZnO厚膜。使用金属Zn作为阳极电极,沉积电势为0.65 V,电解液浓度为0.4 mol/L时,实现了1 h生长14.85μm的ZnO厚膜。在5 V偏压下,基于ZnO厚膜的探测器对加速电压为40 kV的X射线的响应度可达66.8μC·Gy^(-1)·cm^(-2)。

Effects of Atomic Oxygen Irradiation on Transparent Conductive Oxide Thin Films

Transparent conductive oxide （TCO） thin film is a kind of functional material which has potential applications in solar cells and atomic oxygen （AO） resisting systems in spacecrafts. Of TCO, ZnO：Al （ZAO） and In2O3：Sn （ITO） thin films have been widely used and investigated. In this study, ZAO and ITO thin films were irradiated by AO with different amounts of fluence. The as-deposited samples and irradiated ones were characterized by X-ray diffraction （XRD）, scanning electron microscopy （SEM） and Hall-effect measurement to investigate the dependence of the structure, morphology and electrical properties of ZAO or ITO on the amount of fluence of AO irradiation. It is noticed that AO has erosion effects on the surface of ZAO without evident influences upon its structure and conductive properties. Moreover, as the amount of AO fluence rises, the carrier concentration of ITO decreases causing the resistivity to increase by at most 21.7%.

First-principles study and electronic structures of Mn-doped ultrathin ZnO nanofilms

The first-principles density functional calculation is used to investigate the electronic structures and magnetic properties of Mn-doped and N-co-doped ZnO nanofilms.The band structure calculation shows that the band gaps of ZnO films with 2,4,and 6 layers are larger than the band gap of the bulk with wurtzite structure and decrease with the increase of film thickness.However,the four-layer ZnO nanofilms exhibit ferromagnetic phases for Mn concentrations less than 24% and 12% for Mn-doping performed in the whole layers and two layers of the film respectively,while they exhibit spin glass phases for higher Mn concentrations.It is also found,on the one hand,that the spin glass phase turns into the ferromagnetic one,with the substitution of nitrogen atoms for oxygen atoms,for nitrogen concentrations higher than 16% and 5% for Mn-doping performed in the whole layers and two layers of the film respectively.On the other hand,the spin-glass state is more stable for ZnO bulk containing 5% of Mn impurities,while the ferromagnetic phase is stable by introducing the p-type carriers into the bulk system.Moreover,it is shown that using the effective field theory for ferromagnetic system,the Curie temperature is close to the room temperature for the undamped Ruderman-Kittel-Kasuya-Yoshida（RKKY） interaction.