Effects of particle size （A：d50 = 336. 9 μm, B：d50 =123.5μm, C： d50=19.5 μm, D： dso=2.21μm） and content （1 wt% , 3 wt% , 5 wt% , 7 wt% ） of silicon powder on cold crushing strength （CCS） , pore size dis...Effects of particle size （A：d50 = 336. 9 μm, B：d50 =123.5μm, C： d50=19.5 μm, D： dso=2.21μm） and content （1 wt% , 3 wt% , 5 wt% , 7 wt% ） of silicon powder on cold crushing strength （CCS） , pore size distribution and microstructure of Al2O3 - ZrO2 - C refractories coked at high temperature had been investigated by means of mercury porosimeter, SEM, EDS, tic. The results indicated that particle size and content of silicon powder affected the cold crushing strength of coked specimens. It increased with the addition of silicon powder and its finer particle size. However, it decreased greatly when using too fine silicon powder. The particle size and content of silicon powder also impacted the phase evolution and microstructure of coked specimens, much more β-SiC whiskers constituted network structure and well distributed in specimens with reduction of their slenderness ratios when finer silicon powder was added, corresponding to that, the specimens＇ pore size distribution range became narrower with smaller pore diameter, but β-SiC whiskers were distributed sparsely and the specific pore volume of small pores increased when much finer powder was added. It was worthly mentioned that some nitride could form in specimens with addition of appropriate particle size and content of silicon powder.展开更多
The effects of crystallite size on the physicochemical properties and surface defects of pure monoclinic ZrO_(2) catalysts for isobutene synthesis were studied.We prepared a series of monoclinic ZrO_(2) catalysts with...The effects of crystallite size on the physicochemical properties and surface defects of pure monoclinic ZrO_(2) catalysts for isobutene synthesis were studied.We prepared a series of monoclinic ZrO_(2) catalysts with different crystallite size by changing calcination temperature and evaluated their catalytic performance for isobutene synthesis from syngas.ZrO_(2) with small crystalline size showed higher CO conversion and isobutene selectivity,while samples with large crystalline size preferred to form dimethyl ether(DME)instead of hydrocarbons,much less to isobutene.Oxygen defects(ODefects)analyzed by X-ray photoelectron spectroscopy(XPS)provided evidence that more ODefectsoccupied on the surface of ZrO_(2) catalysts with smaller crystalline size.Electron paramagnetic resonance(EPR)and ultraviolet–visible diffuse reflectance(UV–vis DRS)confirmed the presence of high concentration of surface defects and Zr3+on mZrO_(2)-5.9 sample,respectively.In situ diffuse reflectance infrared Fourier transform spectroscopy(in situ DRIFTS)analysis indicated that the adsorption strength of formed formate species on catalyst reduced as the crystalline size decreased.These results suggested that surface defects were responsible for CO activation and further influenced the adsorption strength of surface species,and thus the products distribution changed.This study provides an in-depth insight for active sites regulation of ZrO_(2) catalyst in CO hydrogenation reaction.展开更多
Nanocrystalline TiO2 was prepared by high frequency plasma chemical vapor deposition (HF-PCVD). The effects of additive AlCl3 on crystal phase, particle size and microstructurai parameters of TiO2 nanocrystallites wer...Nanocrystalline TiO2 was prepared by high frequency plasma chemical vapor deposition (HF-PCVD). The effects of additive AlCl3 on crystal phase, particle size and microstructurai parameters of TiO2 nanocrystallites were investigated by X-ray diffraction(XRD) and transmission electron microscopy (TEM). The nanocrystallites obtained experimentally are mixture of anatase and rutile, the uniform diameters of particles are about 30 nm. The phase transformation from anatase to rutile was accelerated by AlCl3, and rutile content is increased from 26.7 wt pct to 53.6 wt pct with increasing of addition of AlCl3 from 0.0 wt pct to 5.0 wt pct. The particle size is reduced and the size distribution becomes very narrow. The crystal lattice constants have the trend to decrease, and celi volumes appear as shrinkable.展开更多
The Y-Eu oxalate precursor was prepared with a homogeneous precipitation method. And the additives, Na2CO3, S, NaCl or their combination, were introduced into the precursor to prepare Y2O3 ：Eu^3＋ red phosphors at 10...The Y-Eu oxalate precursor was prepared with a homogeneous precipitation method. And the additives, Na2CO3, S, NaCl or their combination, were introduced into the precursor to prepare Y2O3 ：Eu^3＋ red phosphors at 1000 1300 ℃ for 2 h. The effect of molten salts on particle size and luminescent intensity was studied. The experimental results showed that the complex molten salt （Na：CO3 ＋ S ＋ NaCl） was conductive to enhance the luminescent intensity of Y2O3 ：Eu^3＋. The emission intensity of the phosphor prepared with these additives at 1300 ℃ was about 45% higher than that of the one prepared without molten salt, and about 11% higher than that of the corresponding commercial phosphor. Meanwhile, the particle size of Y2O3 ：Eu^3＋ phosphor was controlled effectively with the molten salt.展开更多
Production of’renewable Methane’has attracted renewed research interest as a fundamental probe reaction and process for CO_(2)utilization through potential use in Cl fuel production and even for future space explora...Production of’renewable Methane’has attracted renewed research interest as a fundamental probe reaction and process for CO_(2)utilization through potential use in Cl fuel production and even for future space exploration technologies.CO_(2)methanation is a structure sensitive reaction on Ni/CeO_(2)catalysts.To precisely elucidate the size effect of the Ni metal center on the CO_(2)methanation performance,we prepared2%Ni/CeO_(2)catalysts with pre-synthesized uniform Ni particles(2,4 and 8 nm)on a high surface area CeO_(2)support.Transmission electron microscopy(TEM)and ambient pressure X-ray photo spectroscopy(AP-XPS)characterization have confirmed that the catalyst structure and chemical state was uniform and stable under reaction conditions.The 8 nm sized catalyst showed superior methanation selectivity over the 4 and 2 nm counterparts,and the methanation activity in term of TOF is 10 times and 70 times higher than for the 4 and 2 nm counterparts,respectively.The DRIFTS studies revealed that the larger Ni(8 nm particles)over CeO_(2)efficiently facilitated the hydrogenation of the surface formate intermediates,which is proposed as the rate determining step accounting for the excellent CO_(2)methanation performance.展开更多
The microporous nanocry'sta1line TiO2 electrode with large surface roughness factor hasbeen prepared on a conducting glass support. Modification of the TiO2 electrode by in situ preparingquantum sized RuS2 particl...The microporous nanocry'sta1line TiO2 electrode with large surface roughness factor hasbeen prepared on a conducting glass support. Modification of the TiO2 electrode by in situ preparingquantum sized RuS2 particles on the surface of TiO2 electrode extends the optical absorptionspectrum and photocurrent action specmim into visible region. In addition, compared with RuS2 bulknlaterials- a blue shifi in both absorption spectrum and photocurrent action speCtrum of RuS2rriO2elcctrode is obserived and explained in terms of quantum sized effect.展开更多
Silane coupling agent KH560 was used to modify the surface of nano-α-Al<sub>2</sub>O<sub>3</sub> in ethanol-aqueous solution with different proportions. The particle size of nano-α-Al<sub&...Silane coupling agent KH560 was used to modify the surface of nano-α-Al<sub>2</sub>O<sub>3</sub> in ethanol-aqueous solution with different proportions. The particle size of nano-α-Al<sub>2</sub>O<sub>3</sub> was determined by nano-particle size analyzer, and the effects of nano-α-Al<sub>2</sub>O<sub>3</sub> content, ethanol-aqueous solution ratio and KH560 dosage on the dispersion and particle size of nano-α-Al<sub>2</sub>O<sub>3</sub> were investigated. The material structure before and after modification was determined by Fourier transform infrared spectroscopy (FTIR). Aqueous polyurethane resin and inorganic components are combined with modified nano-α-Al<sub>2</sub>O<sub>3</sub> dispersion to form chromium-free passivation solution. The solution is coated on the galvanized sheet, the adhesion and surface hardness are tested, the bonding strength of the coating and the surface hardness of the substrate are discussed. The corrosion resistance and surface morphology of the matrix were investigated by electrochemical test, neutral salt spray test and scanning electron microscope test. The chromium-free passivation film formed after the modification of nano-α-Al<sub>2</sub>O<sub>3</sub> increases the surface hardness of galvanized sheet by about 85%. The corrosion resistance of the film is better than that of a single polyurethane film. The results show that the surface hardness and corrosion resistance of polyurethane resin composite passivation film are significantly improved by the introduction of nano-α-Al<sub>2</sub>O<sub>3</sub>.展开更多
文摘Effects of particle size （A：d50 = 336. 9 μm, B：d50 =123.5μm, C： d50=19.5 μm, D： dso=2.21μm） and content （1 wt% , 3 wt% , 5 wt% , 7 wt% ） of silicon powder on cold crushing strength （CCS） , pore size distribution and microstructure of Al2O3 - ZrO2 - C refractories coked at high temperature had been investigated by means of mercury porosimeter, SEM, EDS, tic. The results indicated that particle size and content of silicon powder affected the cold crushing strength of coked specimens. It increased with the addition of silicon powder and its finer particle size. However, it decreased greatly when using too fine silicon powder. The particle size and content of silicon powder also impacted the phase evolution and microstructure of coked specimens, much more β-SiC whiskers constituted network structure and well distributed in specimens with reduction of their slenderness ratios when finer silicon powder was added, corresponding to that, the specimens＇ pore size distribution range became narrower with smaller pore diameter, but β-SiC whiskers were distributed sparsely and the specific pore volume of small pores increased when much finer powder was added. It was worthly mentioned that some nitride could form in specimens with addition of appropriate particle size and content of silicon powder.
基金financially supported by the Natural Science Foundation of China(21978312,21908235 and 21802155)the Key Research Program of Frontier Sciences,CAS(QYZDB–SSW–JS C043)+1 种基金Foundation of State Key Laboratory of Highefficiency Utilization of Coal and Green Chemical Engineering(2019-KF-05 and 2018-K22)Supported by Shanxi Scholarship Council of China and Fund Program for the Scientific Activities of Selected Returned Overseas Professionals in Shanxi Province are also greatly appreciated。
文摘The effects of crystallite size on the physicochemical properties and surface defects of pure monoclinic ZrO_(2) catalysts for isobutene synthesis were studied.We prepared a series of monoclinic ZrO_(2) catalysts with different crystallite size by changing calcination temperature and evaluated their catalytic performance for isobutene synthesis from syngas.ZrO_(2) with small crystalline size showed higher CO conversion and isobutene selectivity,while samples with large crystalline size preferred to form dimethyl ether(DME)instead of hydrocarbons,much less to isobutene.Oxygen defects(ODefects)analyzed by X-ray photoelectron spectroscopy(XPS)provided evidence that more ODefectsoccupied on the surface of ZrO_(2) catalysts with smaller crystalline size.Electron paramagnetic resonance(EPR)and ultraviolet–visible diffuse reflectance(UV–vis DRS)confirmed the presence of high concentration of surface defects and Zr3+on mZrO_(2)-5.9 sample,respectively.In situ diffuse reflectance infrared Fourier transform spectroscopy(in situ DRIFTS)analysis indicated that the adsorption strength of formed formate species on catalyst reduced as the crystalline size decreased.These results suggested that surface defects were responsible for CO activation and further influenced the adsorption strength of surface species,and thus the products distribution changed.This study provides an in-depth insight for active sites regulation of ZrO_(2) catalyst in CO hydrogenation reaction.
文摘Nanocrystalline TiO2 was prepared by high frequency plasma chemical vapor deposition (HF-PCVD). The effects of additive AlCl3 on crystal phase, particle size and microstructurai parameters of TiO2 nanocrystallites were investigated by X-ray diffraction(XRD) and transmission electron microscopy (TEM). The nanocrystallites obtained experimentally are mixture of anatase and rutile, the uniform diameters of particles are about 30 nm. The phase transformation from anatase to rutile was accelerated by AlCl3, and rutile content is increased from 26.7 wt pct to 53.6 wt pct with increasing of addition of AlCl3 from 0.0 wt pct to 5.0 wt pct. The particle size is reduced and the size distribution becomes very narrow. The crystal lattice constants have the trend to decrease, and celi volumes appear as shrinkable.
基金Project supported by the National Natural Science Foundation of China (50372086)the Ministry of Science and Technology of Chi-na (2006CB601104)
文摘The Y-Eu oxalate precursor was prepared with a homogeneous precipitation method. And the additives, Na2CO3, S, NaCl or their combination, were introduced into the precursor to prepare Y2O3 ：Eu^3＋ red phosphors at 1000 1300 ℃ for 2 h. The effect of molten salts on particle size and luminescent intensity was studied. The experimental results showed that the complex molten salt （Na：CO3 ＋ S ＋ NaCl） was conductive to enhance the luminescent intensity of Y2O3 ：Eu^3＋. The emission intensity of the phosphor prepared with these additives at 1300 ℃ was about 45% higher than that of the one prepared without molten salt, and about 11% higher than that of the corresponding commercial phosphor. Meanwhile, the particle size of Y2O3 ：Eu^3＋ phosphor was controlled effectively with the molten salt.
基金supported by the U.S.Department of Energy under contract no.DE-SC0012704supported by a U.S.Department of Energy Early Career Award+2 种基金ICREA Academia program and projects MICINN/FEDER RTI2018093996-B-C31 and GC 2017 SGR 128financial support from the Natural Science Foundation of China(22002140)Young Elite Scientist Sponsorship Program by CAST,NO.2019QNRC001。
文摘Production of’renewable Methane’has attracted renewed research interest as a fundamental probe reaction and process for CO_(2)utilization through potential use in Cl fuel production and even for future space exploration technologies.CO_(2)methanation is a structure sensitive reaction on Ni/CeO_(2)catalysts.To precisely elucidate the size effect of the Ni metal center on the CO_(2)methanation performance,we prepared2%Ni/CeO_(2)catalysts with pre-synthesized uniform Ni particles(2,4 and 8 nm)on a high surface area CeO_(2)support.Transmission electron microscopy(TEM)and ambient pressure X-ray photo spectroscopy(AP-XPS)characterization have confirmed that the catalyst structure and chemical state was uniform and stable under reaction conditions.The 8 nm sized catalyst showed superior methanation selectivity over the 4 and 2 nm counterparts,and the methanation activity in term of TOF is 10 times and 70 times higher than for the 4 and 2 nm counterparts,respectively.The DRIFTS studies revealed that the larger Ni(8 nm particles)over CeO_(2)efficiently facilitated the hydrogenation of the surface formate intermediates,which is proposed as the rate determining step accounting for the excellent CO_(2)methanation performance.
文摘The microporous nanocry'sta1line TiO2 electrode with large surface roughness factor hasbeen prepared on a conducting glass support. Modification of the TiO2 electrode by in situ preparingquantum sized RuS2 particles on the surface of TiO2 electrode extends the optical absorptionspectrum and photocurrent action specmim into visible region. In addition, compared with RuS2 bulknlaterials- a blue shifi in both absorption spectrum and photocurrent action speCtrum of RuS2rriO2elcctrode is obserived and explained in terms of quantum sized effect.
文摘Silane coupling agent KH560 was used to modify the surface of nano-α-Al<sub>2</sub>O<sub>3</sub> in ethanol-aqueous solution with different proportions. The particle size of nano-α-Al<sub>2</sub>O<sub>3</sub> was determined by nano-particle size analyzer, and the effects of nano-α-Al<sub>2</sub>O<sub>3</sub> content, ethanol-aqueous solution ratio and KH560 dosage on the dispersion and particle size of nano-α-Al<sub>2</sub>O<sub>3</sub> were investigated. The material structure before and after modification was determined by Fourier transform infrared spectroscopy (FTIR). Aqueous polyurethane resin and inorganic components are combined with modified nano-α-Al<sub>2</sub>O<sub>3</sub> dispersion to form chromium-free passivation solution. The solution is coated on the galvanized sheet, the adhesion and surface hardness are tested, the bonding strength of the coating and the surface hardness of the substrate are discussed. The corrosion resistance and surface morphology of the matrix were investigated by electrochemical test, neutral salt spray test and scanning electron microscope test. The chromium-free passivation film formed after the modification of nano-α-Al<sub>2</sub>O<sub>3</sub> increases the surface hardness of galvanized sheet by about 85%. The corrosion resistance of the film is better than that of a single polyurethane film. The results show that the surface hardness and corrosion resistance of polyurethane resin composite passivation film are significantly improved by the introduction of nano-α-Al<sub>2</sub>O<sub>3</sub>.
