A chemo-mechanical model is developed to investigate the effects on the stress development of the coating of polycrystalline Ni-rich LiNixMnyCo_(z)O_(2)(x≥0.8)(NMC)particles with poly(3,4-ethylenedioxythiophene)(PEDO...A chemo-mechanical model is developed to investigate the effects on the stress development of the coating of polycrystalline Ni-rich LiNixMnyCo_(z)O_(2)(x≥0.8)(NMC)particles with poly(3,4-ethylenedioxythiophene)(PEDOT).The simulation results show that the coating of primary NMC particles significantly reduces the stress generation by efficiently accommodating the volume change associated with the lithium diffusion,and the coating layer plays roles both as a cushion against the volume change and a channel for the lithium transport,promoting the lithium distribution across the secondary particles more homogeneously.Besides,the lower stiffness,higher ionic conductivity,and larger thickness of the coating layer improve the stress mitigation.This paper provides a mathematical framework for calculating the chemo-mechanical responses of anisotropic electrode materials and fundamental insights into how the coating of NMC active particles mitigates stress levels.展开更多
The influence of Mo and ZrO_(2)nanoparticles addition on the interfacial properties and shear strength of Sn58Bi solder joint was investigated.The interfacial microstructures of Sn58Bi/Cu,Sn58Bi+Mo/Cu and Sn58Bi+ZrO_(...The influence of Mo and ZrO_(2)nanoparticles addition on the interfacial properties and shear strength of Sn58Bi solder joint was investigated.The interfacial microstructures of Sn58Bi/Cu,Sn58Bi+Mo/Cu and Sn58Bi+ZrO_(2)/Cu solder joints were analysed using a scanning electron microscope(SEM)coupled with energy dispersive X-ray(EDX)and the X-ray diffraction(XRD).Intermetallic compounds(IMCs)of MoSn_(2)are detected in the Sn58Bi+Mo/Cu solder joint,while SnZr,Zr_(5)Sn_(3),ZrCu and ZrSn_(2)are detected in Sn58Bi+ZrO_(2)/Cu solder joint.IMC layers for both composite solders comprise of Cu_(6)Sn_(5) and Cu_(3)Sn.The SEM images of these layers were used to measure the IMC layer’s thickness.The average IMC layer’s thickness is 1.4431μm for Sn58Bi+Mo/Cu and 0.9112μm for Sn58Bi+ZrO_(2)/Cu solder joints.Shear strength of the solder joints was investigated via the single shear lap test method.The average maximum load and shear stress of the Sn58Bi+Mo/Cu and Sn58Bi+ZrO_(2)/Cu solder joints are increased by 33%and 69%,respectively,as compared to those of the Sn58Bi/Cu solder joint.By comparing both composite solder joints,the latter prevails better as adding smaller sized ZrO_(2)nanoparticles improves the interfacial properties granting a stronger solder joint.展开更多
We derive an effective Hamiltonian for a spin-1/2 particle confined within a curved thin layer with non-uniform thickness using the confining potential approach.Our analysis reveals the presence of a pseudo-magnetic f...We derive an effective Hamiltonian for a spin-1/2 particle confined within a curved thin layer with non-uniform thickness using the confining potential approach.Our analysis reveals the presence of a pseudo-magnetic field and effective spin–orbit interaction(SOI)arising from the curvature,as well as an effective scalar potential resulting from variations in thickness.Importantly,we demonstrate that the physical effect of additional SOI from thickness fluctuations vanishes in low-dimensional systems,thus guaranteeing the robustness of spin interference measurements to thickness imperfection.Furthermore,we establish the applicability of the effective Hamiltonian in both symmetric and asymmetric confinement scenarios,which is crucial for its utilization in one-side etching systems.展开更多
The capture,regeneration,and conversion of CO_(2)from ambient air and flue gas streams are critical aspects of mitigating global warming.Solid sorbents for CO_(2)absorption are very promising as they have high mass tr...The capture,regeneration,and conversion of CO_(2)from ambient air and flue gas streams are critical aspects of mitigating global warming.Solid sorbents for CO_(2)absorption are very promising as they have high mass transfer areas without energy input and reduce emissions and minimize corrosion as compared to liquid sorbents.However,precisely tunable solid CO_(2)sorbents are difficult to produce.Here,we demonstrate the high-throughput production of hydrogel-based CO_(2)-absorbing particles via liquid jetting.By wrapping a liquid jet consisting of an aqueous solution of cross-linkable branched polyethylenimine(PEI)with a layer of suspension containing hydrophobic silica nanoparticles,monodisperse droplets with a silica nanoparticle coating layer was formed in the air.A stable Pickering emulsion containing PEI droplets was obtained after these ejected droplets were collected in a heated oil bath.The droplets turn into mm-sized particles after thermal curing in the bath.The diameter,PEI content,and silica content of the particles were systematically varied,and their CO_(2)absorption was measured as a function of time.Steam regeneration of the particles enabled cyclic testing,revealing a CO_(2)absorption capacity of 6.5±0.5 mol kg^(−1)solid PEI in pure CO_(2)environments and 0.7±0.3 mol kg^(−1)solid PEI for direct air capture.Several thousands of particles were produced per second at a rate of around 0.5 kg per hour,with a single nozzle.This process can be further scaled by parallelization.The complete toolbox for the design,fabrication,testing,and regeneration of functional hydrogel particles provides a powerful route toward novel solid sorbents for regenerative CO_(2)capture.展开更多
Ce0.6Zr0.4O2 solid solution ultrafine particle was prepared in the cyclohexane/water/OP-10/n-hexanol reversed microemulsion. The quasi-ternary phase diagram investigations showed that the system has narrow W/O type mi...Ce0.6Zr0.4O2 solid solution ultrafine particle was prepared in the cyclohexane/water/OP-10/n-hexanol reversed microemulsion. The quasi-ternary phase diagram investigations showed that the system has narrow W/O type microemulison region, so it is the proper system to prepare Ce0.6Zr0.4O2 solid solution ultrafine particle. Some physical-chemical techniques such as TG/DTA, XRD, BET, and HRTEM are used to characterize the resultant powders. The results show that the fluorite cubic Ce0.6Zr0.4O2 solid solution is obtained at 400 ℃. The surface area is （146.7 m^2·g^-1）, which is higher than the surface area for sol-gel prepared sample （59.5m^2·g^-1）. HRTEM images indicated that the Ce0.6Zr0.4O2 solid solution ultrafine particle is well-crystallized, narrow size distribution, less agglomeration, within mean size of 5 -7 nm.展开更多
By a novel technique-cathodic micro-arc electro-deposition (CMED), ZrO_2coatings were deposited on an FeCrAl alloy. Experimental results show that the necessary conditionsfor obtaining ZrO_2 coatings are to apply a pu...By a novel technique-cathodic micro-arc electro-deposition (CMED), ZrO_2coatings were deposited on an FeCrAl alloy. Experimental results show that the necessary conditionsfor obtaining ZrO_2 coatings are to apply a pulse peak voltage over a critical value and addmoderate amounts of ZrO_2 colloidal particles and Zr(NO_3)_4 in the aqueous solution. Theas-deposited coatings are porous because hydrogen, water, and other vapors are generated andreleased from the coatings to the solution during the spark reaction. The coatings containmonoclinic and tetragonal crystalline ZrO_2 with certain degree of amorphous structure. Theprocessing parameters and mechanism of CMED were discussed.展开更多
Effects of particle size （A：d50 = 336. 9 μm, B：d50 =123.5μm, C： d50=19.5 μm, D： dso=2.21μm） and content （1 wt% , 3 wt% , 5 wt% , 7 wt% ） of silicon powder on cold crushing strength （CCS） , pore size dis...Effects of particle size （A：d50 = 336. 9 μm, B：d50 =123.5μm, C： d50=19.5 μm, D： dso=2.21μm） and content （1 wt% , 3 wt% , 5 wt% , 7 wt% ） of silicon powder on cold crushing strength （CCS） , pore size distribution and microstructure of Al2O3 - ZrO2 - C refractories coked at high temperature had been investigated by means of mercury porosimeter, SEM, EDS, tic. The results indicated that particle size and content of silicon powder affected the cold crushing strength of coked specimens. It increased with the addition of silicon powder and its finer particle size. However, it decreased greatly when using too fine silicon powder. The particle size and content of silicon powder also impacted the phase evolution and microstructure of coked specimens, much more β-SiC whiskers constituted network structure and well distributed in specimens with reduction of their slenderness ratios when finer silicon powder was added, corresponding to that, the specimens＇ pore size distribution range became narrower with smaller pore diameter, but β-SiC whiskers were distributed sparsely and the specific pore volume of small pores increased when much finer powder was added. It was worthly mentioned that some nitride could form in specimens with addition of appropriate particle size and content of silicon powder.展开更多
基金the National Research Foundation of Korea(Nos.2018R1A5A7023490 and 2022R1A2C1003003)。
文摘A chemo-mechanical model is developed to investigate the effects on the stress development of the coating of polycrystalline Ni-rich LiNixMnyCo_(z)O_(2)(x≥0.8)(NMC)particles with poly(3,4-ethylenedioxythiophene)(PEDOT).The simulation results show that the coating of primary NMC particles significantly reduces the stress generation by efficiently accommodating the volume change associated with the lithium diffusion,and the coating layer plays roles both as a cushion against the volume change and a channel for the lithium transport,promoting the lithium distribution across the secondary particles more homogeneously.Besides,the lower stiffness,higher ionic conductivity,and larger thickness of the coating layer improve the stress mitigation.This paper provides a mathematical framework for calculating the chemo-mechanical responses of anisotropic electrode materials and fundamental insights into how the coating of NMC active particles mitigates stress levels.
文摘The influence of Mo and ZrO_(2)nanoparticles addition on the interfacial properties and shear strength of Sn58Bi solder joint was investigated.The interfacial microstructures of Sn58Bi/Cu,Sn58Bi+Mo/Cu and Sn58Bi+ZrO_(2)/Cu solder joints were analysed using a scanning electron microscope(SEM)coupled with energy dispersive X-ray(EDX)and the X-ray diffraction(XRD).Intermetallic compounds(IMCs)of MoSn_(2)are detected in the Sn58Bi+Mo/Cu solder joint,while SnZr,Zr_(5)Sn_(3),ZrCu and ZrSn_(2)are detected in Sn58Bi+ZrO_(2)/Cu solder joint.IMC layers for both composite solders comprise of Cu_(6)Sn_(5) and Cu_(3)Sn.The SEM images of these layers were used to measure the IMC layer’s thickness.The average IMC layer’s thickness is 1.4431μm for Sn58Bi+Mo/Cu and 0.9112μm for Sn58Bi+ZrO_(2)/Cu solder joints.Shear strength of the solder joints was investigated via the single shear lap test method.The average maximum load and shear stress of the Sn58Bi+Mo/Cu and Sn58Bi+ZrO_(2)/Cu solder joints are increased by 33%and 69%,respectively,as compared to those of the Sn58Bi/Cu solder joint.By comparing both composite solder joints,the latter prevails better as adding smaller sized ZrO_(2)nanoparticles improves the interfacial properties granting a stronger solder joint.
基金This work was supported in part by the National Natural Science Foundation of China(Grant No.12104239)National Natural Science Foundation of Jiangsu Province of China(Grant No.BK20210581)+2 种基金Nanjing University of Posts and Telecommunications Science Foundation(Grant Nos.NY221024 and NY221100)the Science and Technology Program of Guangxi,China(Grant No.2018AD19310)the Jiangxi Provincial Natural Science Foundation(Grant No.20224BAB211020).
文摘We derive an effective Hamiltonian for a spin-1/2 particle confined within a curved thin layer with non-uniform thickness using the confining potential approach.Our analysis reveals the presence of a pseudo-magnetic field and effective spin–orbit interaction(SOI)arising from the curvature,as well as an effective scalar potential resulting from variations in thickness.Importantly,we demonstrate that the physical effect of additional SOI from thickness fluctuations vanishes in low-dimensional systems,thus guaranteeing the robustness of spin interference measurements to thickness imperfection.Furthermore,we establish the applicability of the effective Hamiltonian in both symmetric and asymmetric confinement scenarios,which is crucial for its utilization in one-side etching systems.
基金supported by the European Regional Development Fund(CONTROL,EFRO#00943).
文摘The capture,regeneration,and conversion of CO_(2)from ambient air and flue gas streams are critical aspects of mitigating global warming.Solid sorbents for CO_(2)absorption are very promising as they have high mass transfer areas without energy input and reduce emissions and minimize corrosion as compared to liquid sorbents.However,precisely tunable solid CO_(2)sorbents are difficult to produce.Here,we demonstrate the high-throughput production of hydrogel-based CO_(2)-absorbing particles via liquid jetting.By wrapping a liquid jet consisting of an aqueous solution of cross-linkable branched polyethylenimine(PEI)with a layer of suspension containing hydrophobic silica nanoparticles,monodisperse droplets with a silica nanoparticle coating layer was formed in the air.A stable Pickering emulsion containing PEI droplets was obtained after these ejected droplets were collected in a heated oil bath.The droplets turn into mm-sized particles after thermal curing in the bath.The diameter,PEI content,and silica content of the particles were systematically varied,and their CO_(2)absorption was measured as a function of time.Steam regeneration of the particles enabled cyclic testing,revealing a CO_(2)absorption capacity of 6.5±0.5 mol kg^(−1)solid PEI in pure CO_(2)environments and 0.7±0.3 mol kg^(−1)solid PEI for direct air capture.Several thousands of particles were produced per second at a rate of around 0.5 kg per hour,with a single nozzle.This process can be further scaled by parallelization.The complete toolbox for the design,fabrication,testing,and regeneration of functional hydrogel particles provides a powerful route toward novel solid sorbents for regenerative CO_(2)capture.
文摘Ce0.6Zr0.4O2 solid solution ultrafine particle was prepared in the cyclohexane/water/OP-10/n-hexanol reversed microemulsion. The quasi-ternary phase diagram investigations showed that the system has narrow W/O type microemulison region, so it is the proper system to prepare Ce0.6Zr0.4O2 solid solution ultrafine particle. Some physical-chemical techniques such as TG/DTA, XRD, BET, and HRTEM are used to characterize the resultant powders. The results show that the fluorite cubic Ce0.6Zr0.4O2 solid solution is obtained at 400 ℃. The surface area is （146.7 m^2·g^-1）, which is higher than the surface area for sol-gel prepared sample （59.5m^2·g^-1）. HRTEM images indicated that the Ce0.6Zr0.4O2 solid solution ultrafine particle is well-crystallized, narrow size distribution, less agglomeration, within mean size of 5 -7 nm.
基金This work was financially supported by the National Natural Science Foundation of China (No.59971009) Beijing Key Laboratory for Corrosion, Erosion and Surface Technology.
文摘By a novel technique-cathodic micro-arc electro-deposition (CMED), ZrO_2coatings were deposited on an FeCrAl alloy. Experimental results show that the necessary conditionsfor obtaining ZrO_2 coatings are to apply a pulse peak voltage over a critical value and addmoderate amounts of ZrO_2 colloidal particles and Zr(NO_3)_4 in the aqueous solution. Theas-deposited coatings are porous because hydrogen, water, and other vapors are generated andreleased from the coatings to the solution during the spark reaction. The coatings containmonoclinic and tetragonal crystalline ZrO_2 with certain degree of amorphous structure. Theprocessing parameters and mechanism of CMED were discussed.
文摘Effects of particle size （A：d50 = 336. 9 μm, B：d50 =123.5μm, C： d50=19.5 μm, D： dso=2.21μm） and content （1 wt% , 3 wt% , 5 wt% , 7 wt% ） of silicon powder on cold crushing strength （CCS） , pore size distribution and microstructure of Al2O3 - ZrO2 - C refractories coked at high temperature had been investigated by means of mercury porosimeter, SEM, EDS, tic. The results indicated that particle size and content of silicon powder affected the cold crushing strength of coked specimens. It increased with the addition of silicon powder and its finer particle size. However, it decreased greatly when using too fine silicon powder. The particle size and content of silicon powder also impacted the phase evolution and microstructure of coked specimens, much more β-SiC whiskers constituted network structure and well distributed in specimens with reduction of their slenderness ratios when finer silicon powder was added, corresponding to that, the specimens＇ pore size distribution range became narrower with smaller pore diameter, but β-SiC whiskers were distributed sparsely and the specific pore volume of small pores increased when much finer powder was added. It was worthly mentioned that some nitride could form in specimens with addition of appropriate particle size and content of silicon powder.
