Preparation of Alumina Abrasion-Resistant Ceramic Grinding Ball with Spent FCC Equilibrium Catalyst

The chemical composition, structure and thermal stability of the spent FCC equilibrium catalyst from an oil refinery were characterized by XRD, FT-IR, DTA-TG, BET, complete chemical analysis, SEM, and XRF. The spent FCC equilibrium catalyst, clay, barium carbonate, and talc were used as the main raw materials to prepare the alumina abrasion-resistant ceramic balls to be used in the powder grinding mill for manufacture of architecture tiles. The results showed that after proper formulation study, the spent FCC equilibrium catalyst could replace industrial alumina to prepare high performance grinding balls. Meanwhile, the various performance indices of the grinding ball could meet the quality standard for similar products, and additionally, the energy saving effect was achieved in the operation of the grinding section, resulting in a successful comprehensive utilization of solid wastes.

The Abrasion-resistance Investigation of Rubberized Concrete

The abrasion resistance properties of rubberized concrete were comparatively studied by taking silica fume and crumb tire rubber as the additives. The abrasion tests were conducted in accordance with the Chinese standard test method DL/T 5150 - 2001, two recommended test methods： under water method and ring method, were used. The crumb tire rubbers with the sieve size of 8-mesh and 16-mesh were incorporated into the concrete by replacing same volume of sand and as an additive. The abrasion resistance of concrete was evaluated according to the abrasion resistance strength and the mass loss. Test results show that the addition of silica fume enhanced both compressive strength and abrasion resistance of concrete, and the addition of crumb rubber reduced the compressive strength but increased notably the abrasion resistance of the concrete. Silica fume concrete performed a better abrasion resistance than control concrete, and the rubberized concrete performed a much better abrasion resistance than silica fume concrete. The abrasion resistance of rubberized concrete increased with the increase of rubber content.

Low-temperature characteristicsof rubbers and performance testsof type 120 emergencyvalve diaphragms

Purpose–The type 120 emergency valve is an essential braking component of railway freight trains,butcorresponding diaphragms consisting of natural rubber(NR)and chloroprene rubber(CR)exhibit insufficientaging resistance and low-temperature resistance,respectively.In order to develop type 120 emergency valverubber diaphragms with long-life and high-performance,low-temperatureresistant CR and NR were processed.Design/methodology/approach–The physical properties of the low-temperature-resistant CR and NRwere tested by low-temperature stretching,dynamic mechanical analysis,differential scanning calorimetryand thermogravimetric analysis.Single-valve and single-vehicle tests of type 120 emergency valves werecarried out for emergency diaphragms consisting of NR and CR.Findings–The low-temperature-resistant CR and NR exhibited excellent physical properties.The elasticityand low-temperature resistance of NR were superior to those of CR,whereas the mechanical properties of thetwo rubbers were similar in the temperature range of 0℃–150℃.The NR and CR emergency diaphragms metthe requirements of the single-valve test.In the low-temperature single-vehicle test,only the low-temperaturesensitivity test of the NR emergency diaphragm met the requirements.Originality/value–The innovation of this study is that it provides valuable data and experience for futuredevelopment of type 120 valve rubber diaphragms.

Visualization Analysis of the Impact of Rubber Agroforestry Ecosystem on Soil Microbial Community

Rubber agroforestry systems positively impact soil microbial communities. This study employed a bibliometric approach to explore the research status, hotspots, and development trends related to these effects. Using CiteSpace software, we visually analyzed research literature from the Web of Science (WOS) core database, spanning 2004 to 2024. The focus was on the impact of rubber agroforestry ecosystems on soil microbial communities. The results indicate significant attention from Chinese researchers, who have published numerous influential papers in this field. Authors Liu Wenjie have contributed the most papers, although no stable core author group exists. The Chinese Academy of Sciences is the leading research institution in terms of publication volume. While there is close collaboration between different institutions and countries, the intensity of researcher cooperation is low. The most cited literature emphasizes soil nutrients and structure in rubber agroforestry, laying a foundation for soil microorganism studies. Most cited journals are from countries like Netherlands and the United Kingdom. Key research areas include the effects of rubber intercropping on soil microbial communities, agroforestry management, and soil health. Research development can be divided into three stages: the initial stage (2010-2015), the development stage (2015-2020), and the mature stage (2020-2024). Current studies show that rubber intercropping and rubber-based agroforestry systems enhance soil microbial communities, positively impacting soil health. This paper provides a theoretical basis for the sustainable development of rubber agroforestry systems and improved management plans. Future research could explore the effects of species composition on soil microbiological characteristics and develop methods for species interactions. An in-depth study of the soil microbial community’s structure and function, and its relationship with rubber trees, is crucial. Developing effective, rationally designed rubber agroforestry systems and underground soil microbiome technology will promote sustainability and improve plantation productivity.

Physical and Chemical Characterizations of Rubber Latex Cup Bottom Oil

Rubber latex is an important economic resource. However, the residues from its harvesting are thrown away, even though they contain lipids that can be recycled. This recovery of the residues from the bottom of the cup requires first and foremost their characterization. The aim of this study is therefore to determine the main physical and chemical characteristics of rubber latex cup bottom oil. Oil’s physical parameters determination shows that it has a density of 951 kg∙m−3, a kinematic viscosity of 48.57 cSt and a water content of 0.0845%. Chemical parameters, meanwhile, indicate that this cup bottom residue has a fat content of 95.96%, an acid number of 2.805 mg KOH/g and an iodine number of 92.42 g I2/100g. Therefore, rubber latex cup bottom oil can be used in the formulation of biofuels, biolubricants, paints, varnishes, alkyd resins, polishing oils, soaps, and insecticides.

Effect of graphene oxide with different oxidation degrees on mechanical properties of styrene-butadiene rubber: Experiment and molecular simulation

Graphene oxide(GO)has proven to be an effective reinfor-cing filler for rubber[1].GO has superior mechanical properties,barrier properties,large specific surface area and abundant oxygen-containing functional groups[2].However,the change in the oxidation degree of GO has a great effect on its chemical properties,the interaction between GO and the matrix,and the dispersion uniformity in the rubber matrix,which has a great effect on the reinforcement of rubber[3].

Transient NOE driven signal enhancement of INADEQUATE solid-state NMR spectroscopy for the structural analysis of rubbers

INADEQUATE(Incredible Natural Abundance DoublE QUAntum Transfer Experiment)is one of the most important techniques in revealing the carbon skeleton of organic solids in solid-state NMR spectroscopy.Nevertheless,its use for structural analysis is quite limited due to the low natural abundance of^(13)C-^(13)C connectivity(~0.01%)and thus low sensitivity.Particularly,in semi-solids like rubbers,the sensitivity will be further significantly reduced by the inefficient cross polarization from 1H to^(13)C due to molecular motions induced averaging of^(1)H-^(13)C dipolar couplings.Herein,in this study,we demonstrate that transient nuclear Overhauser effect(NOE)can be used to efficiently enhance^(13)C signals,and thus enable rapid acquisition of two-dimensional(2D)^(13)C INADEQUATE spectra of rubbers.Using chlorobutyl rubber as the model system,it is found that an overall signalto-noise ratio(SNR)enhancement about 22%can be achieved,leading to significant timesaving by about 33%as compared to the direct polarization-based INADEQUATE experiment.Further experimental results on natural rubber and ethylene propylene diene monomer(EPDM)rubber are also shown to demonstrate the robust performance of transient NOE enhanced INADEQUATE experiment.

Seismic evaluation of frequency influence and resonant behavior for lead rubber bearing isolated rigid rectangular liquid tanks

The seismic behavior of a partially filled rigid rectangular liquid tank is investigated under short-and longduration ground motions.A finite element model is developed to analyze the liquid domain by using four-noded quadrilateral elements.The competency of the model is verified with the available results.Parametric studies are conducted for the dynamic parameters of the base-isolated tank,using a lead rubber bearing to evaluate the optimum damping and time period of the isolator.The application of base isolation has reduced the total and impulsive hydrodynamic components of pressure by 80 to 90 percent,and base shear by 15 to 95 percent,depending upon the frequency content and duration of the considered earthquakes.The sloshing amplitude of the base-isolated tank is reduced by 18 to 94 percent for most of the short-duration earthquakes,while it is increased by 17 to 60 percent for the majority of the long-duration earthquakes.Furthermore,resonance studies are carried out through a long-duration harmonic excitation to obtain the dynamic behavior of non-isolated and isolated tanks,using a nonlinear sloshing model.The seismic responses of the base-isolated tank are obtained as higher when the excitation frequency matches the fundamental sloshing frequency rather than the isolator frequency.

Discussion on“Dispersion characteristics of clayey soils containing waste rubber particles”[J Rock Mech Geotech Eng 15(2023)3050-3058]

We read with great interest the recent article by Erenson(2023)entitled“Dispersion characteristics of clayey soils containing waste rubber particles”.The author has studied the dispersion characteristics of clayey soils containing different percentages of waste rubber particles(WRPs)by performing several tests(viz.consistency limit,linear shrinkage limit,double hydrometer,crumb test and pinhole test)and scanning electron microscopy(SEM)analysis on five clayey(viz.Na-activated bentonite,refined ball clay,Ukrainian kaolin,Avanos kaolin and Afyon clay)samples containing 0%,5%,10%and 15%WRPs.It should be noted that Erenson(2023)has presented some interesting observations,but there are some serious issues that we want to share through this discussion and request the author of the original paper to address them to avoid their persistence in the scientific literature.

Mechanical behavior of nanorubber reinforced epoxy over a wide strain rate loading

Nanorubber/epoxy composites containing 0,2,6 and 10 wt%nanorubber are subjected to uniaxial compression over a wide range of strain rate from 8×10^(-4) s^(-1) to~2×10^(4) s^(-1).Unexpectedly,their strain rate sensitivity and strain hardening index increase with increasing nanorubber content.Potential mechanisms are proposed based on numerical simulations using a unit cell model.An increase in the strain rate sensitivity with increasing nanorubber content results from the fact that the nanorubber becomes less incompressible at high strain,generating a higher hydro-static pressure.Adiabatic shear localization starts to occur in the epoxy under a strain rate of 22,000 s^(-1) when the strain exceeds 0.35.The presence of nanorubber in the epoxy reduces adiabatic shear localization by preventing it from propagating.

Hand Cooling Enhances the Proprioceptive Drift during Rubber Hand Illusion

Background: The neural representation of the body is easily altered by integrating multiple sensory signals in the brain. The “Rubber Hand Illusion” (RHI) is one of the most popular experimental paradigms to investigate this phenomenon. During this illusion, ownership of a rubber hand is temporarily induced. It was shown that external and continuous cooling of the palm enhanced the RHI, suggesting an association between altered the autonomic nervous system regulation and altered the sense of ownership of a specific limb. Purpose: To investigate whether artificially cooling the entire hand for a short period affects the magnitude of the illusion. Methods: Participants immersed their entire hand in cool, cold, or warm water for 1 min before the RHI procedure. Results: We found that cooling the entire hand enhanced the proprioceptive drift during the RHI but not the subjective feeling of ownership. In contrast, warming and intense cooling of the entire hand did not affect the RHI strength. Conclusion: Our results suggest that transient and moderate cooling of the entire hand was sufficient in enhancing the illusory disembodiment of one’s own hand.

Natural rubber latex as a potential additive for water-based drilling fluids

The environmental hazards and"carbon footprint"of oil and gas drilling can be significantly reduced by replacing traditional petroleum-based chemical additives with natural materials derived from plants and animals.This paper explored for the first time the interaction mechanism between natural rubber latex(NRL)and bentonite suspensions(BTs)through a series of characterization experiments,as well as the potential applications in water-based drilling fluids(WBDF).The gel viscoelasticity experiments showed that NRL could decrease the consistency coefficient(k)and flow index(n)of BTs,and enhance the shear thinning performance of BTs as pseudo-plastic fluids.In addition,0.5 w/v%NRL not only increased the critical yield stress and strengthened the structural strength between the bentonite particles,but also facilitated the compatibility of pressure loss and flow efficiency.The evaluation of colloidal stability and WBDF performance indicated that NRL particles could promote the hydration and charge stability on the surface of BTs particles,and optimize the particle size distribution and flow resistance of WBDF under the"intercalation-exfoliation-encapsulation"synergistic interaction.Moreover,NRL can improve the rheological properties of WBDF at high temperatures(<150.C),and form a dense blocking layer by bridging and sealing the pores and cracks of the filter cake,which ultimately reduces the permeability of the cake and the filtration loss of WBDF.

Comparison of nonlinear modeling methods for the composite rubber clamp

The cubic stiffness force model(CSFM)and Bouc-Wen model(BWM)are introduced and compared innovatively.The unknown coefficients of the nonlinear models are identified by the genetic algorithm combined with experiments.By fitting the identified nonlinear coefficients under different excitation amplitudes,the nonlinear vibration responses of the system are predicted.The results show that the accuracy of the BWM is higher than that of the CSFM,especially in the non-resonant region.However,the optimization time of the BWM is longer than that of the CSFM.

Solid-state NMR of vulcanized natural rubber/butadiene rubber blends:Local organization and cross-linking heterogeneities This article is part of the virtual special issue“Solid-state NMR studies on polymers and biological solids”

Elastomer blends,among which natural rubber(NR)and butadiene rubber(BR),are involved in many components of the automotive/tire industry.A comprehensive understanding of their mechanical behavior requires,among other features,a detailed description of the crosslink density in these mixtures.In the case of vulcanized immiscible blends,the distribution of the cross-link density within each of the NR-and BR-rich domains is key information,but difficult to determine using the conventional approaches used for one-component crosslinked elastomers.In this study,the vulcanization within NR/BR blends is investigated using a robust^(1)H double-quantum(DQ)MAS recoupling experiment,BaBa-xy16.Two kinds of cross-linked NR/BR blends were considered with two different microstructures for the BR component.The bulk organization of the resulting blends was first probed by analyzing the^(1)H spin-lattice relaxation behavior.In a second step,BaBa-xy16 was used to investigate,in a selective way,the cross-link heterogeneities within NR/BR blends.In particular,for immiscible NR/BR mixtures,the distribution of the cross-link density between both phases was compared and the observed differences were discussed.

Blue rubber blister nevus syndrome: A case report

BACKGROUND Blue rubber blister nevus syndrome(BRBNS)is a congenital,rare disease charac-terized by venous malformations of the skin and internal organs,affecting all systems throughout the body.The pathogenesis is unknown.There is no con-sensus on the treatment of BRBNS.Most of the previously reported cases were mild to moderate with a good prognosis,and this case was a critically ill patient with severe gastrointestinal hemorrhage,disseminated intravascular coagulation(DIC),and severe joint fusion that was different from previously reported cases.CASE SUMMARY An 18-year-old man with early onset of BRBNS in early childhood is reported.He presented with recurrent melena and underwent malformed phlebectomy and partial jejunectomy and ileal resection.The patient had melena before and after surgery.After active treatment,the patient's gastrointestinal bleeding improved.This was a case of atypical BRBNS with severe gastrointestinal bleeding and severe joint fusion,which should be differentiated from other serious joint lesions and provide clinicians with better understanding of this rare disease.CONCLUSION This case of critical BRBNS with gastrointestinal hemorrhage,DIC and severe joint fusion provides further understanding of this rare disease.

Ethylene and jasmonate as stimulants of latex yield in rubber trees(Hevea brasiliensis):Molecular and physiological mechanisms.A systematic approximation review

The rubber tree Hevea brasiliensis(Willd.Ex Adr.De Juss.)Müell Arg.]is an important source of latex for the production natural rubber.Natural rubber is an important biopolymer used in various industries,but aspects related to hormonal regulation in biosynthesis are still unknown,which would allow optimizing its production.We review the molecular and physiological mechanisms of increases latex regeneration and flow by the stimulation of rubber trees with exogenous applications of ethylene and jasmonate.We found that the increase in latex regeneration by ethylene is due to the increase in gene level expression and enzymatic activity of key photosynthesis and glycolysis enzymes for the generation of precursors in the first phase of rubber biosynthesis.Latex flow is supported by up-regulated genes in sucrose metabolism such as invertases,induction of sucrose transporters(SUT),and aquaporins(PIP)to maintain flow and turgor pressure in laticifers.Meanwhile,the increase in latex yield mediated by jasmonate may be due to the induction of laticifer differentiation in the long term and in the short term be mediated by the induction of small rubber particles(SRPP)as non-enzymatic cofactors in the production of latex.This information contributes to the knowledge of latex biosynthesis,which allows for a greater support for the exogenous application of jasmonates and ethylene to regulate its production.

Lexical Characteristics and Translation Strategies of Rubber and Plastic Industry Terms

As a key part of the manufacturing industry,the rubber and plastic industry is widely used in a variety of fields such as automotive manufacturing,construction materials,and electronics.With technological innovation,global economic growth and infrastructure construction driving the demand for rubber and plastic materials,rubber and plastic materials play an important role in various fields,and accurate translation of the industry’s terminology is also crucial for international communication.The purpose of this paper is to explore in depth the lexical features of rubber and plastic industry terminology,including strong specialization,specialization of common vocabulary,and diversity of word formation.In view of these lexical features,relevant Chinese translation strategies are discussed to ensure the accuracy,specialization and comprehensibility of the translation of rubber and plastic industry terms.

Prokaryotic Expression of Rubber Elongation Factor Gene and Preparation of Its Polyclonal Antibody

[Objective] The aim of this study was to prepare the recombination protein of rubber elongation factor and its polyclonal antibodies.[Method] The encoding gene of rubber elongation factor(REF)was amplified by RT-PCR,and cloned into the prokaryotic expression vector pDEST17 to transform into Escherichia coil BI2I-AI.The recombinant protein induced by L-Arabinose was purified by the affinity chromatography.As the immunogen,the recombination protein was used to immunize mice for preparing polyclonal antibodies,while ELISA and Western blot hybridization were used to detect the titers and specificity.[Result] The purified recombination protein of REF with high expression was used to immunize house mice for preparing polyclonal antibodies with high titer and specificity.The western blot hybridization showed that the antibody could recognize the natural REF from latex.[Conclusion] The recombination protein of REF was successfully obtained and the mouse anti REF antibody with high titer and specificity was prepared,which lays a basis for further studies on biological functions of rubber elongation factor and other membrane proteins in rubber particles.

Rubber/UHMWPE复合尾轴承材料及其性能分析

以丁腈橡胶为基体,加入超高分子量聚乙烯(UHMWPE)和石墨等物质进行共混改性,得到一种新型舰船尾管水润滑轴承材料。其物理力学性能达到了我国CB和美国MIL标准,摩擦因数达到了美国军标MIL-DTL-17901C(SH)的标准,在低速下更优于标准。局部最大比压可达0.70 MPa,减振降噪性能优于同类产品,是一种综合性能优异的水润滑轴承材料。

Analysis of Static Temperature Field of Vehicle's Solid Rubber Tire

Aim To analyse the static temperature field ofthe solid rubber tire(SRT).Methods The mechanical and thermal FE models were developed and analyzed respectively with the FE software ANSYS.Results The maximum temperature becomes higher with the higher with the higher velocity of tire and scales down slightly with the higher convection coefficients.The mixed models are reasonable.Conclusion The study on static temperature field is important and reasonable.It gives the fundament for life analysis of SRT.