Enhancing lead-free photovoltaic performance:Minimizing buried surface voids in tin perovskite films through weakly polar solvent pre-treatment strategy

Buried interfacial voids have always been a notorious phenomenon observed in the fabrication of lead perovskite films. The existence of interfacial voids at the buried interface will capture the carrier, suppress carrier transport efficiencies, and affect the stability of photovoltaic devices. However, the impact of these buried interfacial voids on tin perovskites, a promising avenue for advancing lead-free photovoltaics, has been largely overlooked. Here, we utilize an innovative weakly polar solvent pretreatment strategy(WPSPS) to mitigate buried interfacial voids of tin perovskites. Our investigation reveals the presence of numerous voids in tin perovskites during annealing, attributed to trapped dimethyl sulfoxide(DMSO) used in film formation. The WPSPS method facilitates accelerated DMSO evaporation, effectively reducing residual DMSO. Interestingly, the WPSPS shifts the energy level of PEDOT:PSS downward, making it more aligned with the perovskite. This alignment enhances the efficiency of charge carrier transport. As the result, tin perovskite film quality is significantly improved,achieving a maximum power conversion efficiency approaching 12% with only an 8.3% efficiency loss after 1700 h of stability tests, which compares well with the state-of-the-art stability of tin-based perovskite solar cells.

The Clinical Value of Accelerated Recovery Care in Pulmonary Rehabilitation of Perioperative Lung Cancer Patients

Aim: To study the clinical value of accelerated recovery care in pulmonary rehabilitation of perioperative lung cancer patients. Methods: 98 lung cancer patients undergoing surgery were admitted to our hospital from March 2020 to November 2021 and randomly divided into an observation group and an ACBT (Active Cycle of Breathing Technique) training group. Accelerated recovery care and routine care were respectively used in the perioperative period to compare the nursing effects of the two groups. Results: All perioperative indicators in the observation group were shorter than those in the ACBT training group. The pain scores at different time periods after surgery were lower in the observation group than in the ACBT training group (P 0.05). The improvement in the above indicators was higher in the observation group than in the ACBT training group after nursing care (P Conclusion: Accelerated recovery care during the perioperative period for lung cancer surgery patients showed significant effectiveness.

GPU-accelerated OCT imaging: Real-time data processing and artifact suppression for enhanced monitoring of 3D bioprinted tissues and vascular-like networks

Optical coherence tomography(OCT)imaging technology has significant advantages in in situ and noninvasive monitoring of biological tissues.However,it still faces the following challenges:including data processing speed,image quality,and improvements in three-dimensional(3D)visualization effects.OCT technology,especially functional imaging techniques like optical coherence tomography angiography(OCTA),requires a long acquisition time and a large data size.Despite the substantial increase in the acquisition speed of swept source optical coherence tomography(SS-OCT),it still poses significant challenges for data processing.Additionally,during in situ acquisition,image artifacts resulting from interface reflections or strong reflections from biological tissues and culturing containers present obstacles to data visualization and further analysis.Firstly,a customized frequency domainfilter with anti-banding suppression parameters was designed to suppress artifact noises.Then,this study proposed a graphics processing unit(GPU)-based real-time data processing pipeline for SS-OCT,achieving a measured line-process rate of 800 kHz for 3D fast and high-quality data visualization.Furthermore,a GPU-based realtime data processing for CC-OCTA was integrated to acquire dynamic information.Moreover,a vascular-like network chip was prepared using extrusion-based 3D printing and sacrificial materials,with sacrificial material being printed at the desired vascular network locations and then removed to form the vascular-like network.OCTA imaging technology was used to monitor the progression of sacrificial material removal and vascular-like network formation.Therefore,GPU-based OCT enables real-time processing and visualization with artifact suppression,making it particularly suitable for in situ noninvasive longitudinal monitoring of 3D bioprinting tissue and vascular-like networks in microfluidic chips.

Unsteady MHD Casson Nanofluid Flow Past an Exponentially Accelerated Vertical Plate:An Analytical Strategy

In this study,the characteristics of heat transfer on an unsteady magnetohydrodynamic(MHD)Casson nanofluid over an exponentially accelerated vertical porous plate with rotating effects were investigated.The flow was driven by the combined effects of the magnetic field,heat radiation,heat source/sink and chemical reaction.Copper oxide(CuO)and titanium oxide(TiO2)are acknowledged as nanoparticle materials.The nondimensional governing equations were subjected to the Laplace transformation technique to derive closed-form solutions.Graphical representations are provided to analyze how changes in physical parameters,such as the magnetic field,heat radiation,heat source/sink and chemical reaction,affect the velocity,temperature and concentration profiles.The computed values of skin friction,heat and mass transfer rates at the surface were tabulated for various sets of input parameters.It is perceived that there is a drop in temperature due to the rise in the heat source/sink and the Prandtl number.It should be noted that a boost in the thermal radiation parameter prompts an increase in temperature.An increase in the Prandtl number,heat source/sink parameter,time and a decrease in the thermal radiation parameter result in an increase in theNusselt number.The computed values of the skin friction,heat andmass transfer rates at the surface were tabulated for various values of the flow parameters.The present results were compared with those of previously published studies andwere found to be in excellent agreement.This research has practical applications in areas such as drug delivery,thermal medicine and cancer treatment.

Clinical Practice of Evidence-Based PDCA Cycle Management Model in Accelerated Recovery of Lung Cancer Patients

Objective: To explore the nursing effect of evidence-based PDCA cycle management mode in accelerated rehabilitation of patients undergoing thoracoscopic lung cancer radical surgery. Methods: 104 patients who underwent thoracoscopic lung cancer radical surgery in our hospital from June 2022 to February 2023 were randomly divided into control group and intervention group, with 52 cases in each group. The control group implemented evidence-based ERAS clinical pathway management, while the intervention group implemented evidence-based PDCA cycle quality management. The postoperative recovery of the two groups of patients was compared. Results: The postoperative recovery of the intervention group was significantly better than that of the control group. The first time to get out of bed, the first time to eat, the duration of chest drainage tube placement, and the length of hospital stay were significantly shorter than those of the control group. The incidence of postoperative chest complications and hospitalization costs were significantly lower than those of the control group, and patient satisfaction was significantly higher than that of the control group (P Conclusion: Evidence-based PDCA cycle quality management mode can effectively improve the implementation quality of accelerated rehabilitation nursing for patients undergoing thoracoscopic lung cancer radical surgery, and it is worthy of clinical promotion.

Clinical Study of Accelerated Rehabilitation Concept Combined with Tianji Robot-Assisted Surgery in Lumbar Degenerative Diseases

Objective: To compare the effectiveness and safety of two surgical methods for lumbar degenerative diseases;the combination of the concept of accelerated rehabilitation with the assistance of Tianji Robotics and the concept of accelerated rehabilitation combined with manual pedicle screw placement assisted by conventional C-arm fluoroscopy. Methods: A retrospective analysis was performed on 70 patients who received the concept of accelerated rehabilitation combined with spinal surgery for lumbar degenerative diseases in Baise People’s Hospital from January 2022 to January 2024. Among them, 35 patients in the robot group received accelerated rehabilitation concept combined with robot-assisted surgery;In the conventional C-arm group, 35 patients received the accelerated rehabilitation concept combined with manual pedicle screw placement assisted by conventional C-arm fluoroscopy. VAS score (preoperative/postoperative), ODI score (preoperative/postoperative), intraoperative bleeding volume, postoperative hospital stay, postoperative complications and the accuracy rate of screw placement were compared between the two groups. Result: There was no statistically significant difference in preoperative VAS scores between the robot group and the conventional C-arm group (6.45 ± 0.82 VS 6.63 ± 0.81, P = 0.6600). The postoperative VAS score of the robot group was better than that of the conventional C-arm group (1.69 ± 0.80 VS 2.45 ± 0.85, P = 0.0000*). There was no statistically significant difference in preoperative ODI scores between the robot group and the conventional C-arm group (32.11 ± 3.18 VS 31.66 ± 2.25, P = 0.4900). The postoperative ODI score of the robot group was better than that of the conventional C-arm group (22.68 ± 1.94 VS 24.57 ± 2.25, P = 0.0000*). The postoperative complications in the robot group were less than those in the conventional C-arm group (2.7778% VS 28.5724%, P = 0.0030*). The intraoperative bleeding in the robot group was lower than that in the conventional C-arm group (320.85 ± 276.28 VS 490.00 ± 395.34, P = 0.0420*). The postoperative hospital stay of the robot group was shorter than that of the conventional C-arm group (10.00 ± 9.32 VS 14.49 ± 7.55, P = 0.0300*). The screw placement inaccuracy score of the robot group was lower than that of the conventional C-arm group (0.17 ± 0.51 VS 1.45 ± 1.46, P = 0.0000*). Conclusion: The combination of the concept of accelerated rehabilitation and Tianji Orthopedic robot-assisted surgery is more effective and safer in posterior lumbar decompression and internal fixation surgery with a screw rod system, and is worthy of promotion and application.

Early changes in corneal densitometry after FS-LASIK combined with accelerated corneal cross-linking for correction of high myopia

AIM:To observe the effects of femtosecond laserassisted excimer laser in situ keratomileusis combined with accelerated corneal cross-linking(FS-LASIK Xtra)on corneal densitometry after correcting for high myopia.METHODS:In this prospectively study,130 patients underwent FS-LASIK or FS-LASIK Xtra for high myopia.Their right eyes were selected for inclusion in the study,of which 65 cases of 65 eyes in the FS-LASIK group,65 patients with 65 eyes in the FS-LASIK Xtra group.Patients were evaluated for corneal densitometry at 1,3,and 6mo postoperatively using Pentacam Scheimpflug imaging.RESULTS:Preoperative differences in corneal densitometry between the FS-LASIK and FS-LASIK Xtra groups in different ranges were not statistically significant(P>0.05).Layer-by-layer analysis revealed statistically significant differences in the anterior(120μm),central,and total layer corneal densitometry between the FS-LASIK and FS-LASIK Xtra groups at 1 and 3mo postoperatively(all P<0.05),the FS-LASIK Xtra group is higher than that of the FS-LASIK group.Analysis of different diameter ranges showed statistically significant differences between the FS-LASIK group and the FS-LASIK Xtra group at 1mo postoperatively in the ranges of 0–2,2–6,and 6–10 mm(both P<0.05);At 3mo postoperatively,the FS-LASIK Xtra group is higher than that of the FS-LASIK group in the ranges of 0–2 and 2–6 mm(P<0.05).At 6mo postoperatively,there were no statistically significant differences in corneal densitometry between the FS-LASIK group and the FS-LASIK Xtra group in different diameter ranges(all P>0.05).CONCLUSION:There is an increase in internal corneal densitometry during the early postoperative period after FS-LASIK Xtra for correction of high myopia.However,the densitometry values decreased to the level of conventional FS-LASIK at 6mo after surgery,with the most significant changes observed in the superficial central zone.

Accelerated Particle Swarm Optimization Algorithm for Efficient Cluster Head Selection in WSN

Numerous wireless networks have emerged that can be used for short communication ranges where the infrastructure-based networks may fail because of their installation and cost.One of them is a sensor network with embedded sensors working as the primary nodes,termed Wireless Sensor Networks(WSNs),in which numerous sensors are connected to at least one Base Station(BS).These sensors gather information from the environment and transmit it to a BS or gathering location.WSNs have several challenges,including throughput,energy usage,and network lifetime concerns.Different strategies have been applied to get over these restrictions.Clustering may,therefore,be thought of as the best way to solve such issues.Consequently,it is crucial to analyze effective Cluster Head(CH)selection to maximize efficiency throughput,extend the network lifetime,and minimize energy consumption.This paper proposed an Accelerated Particle Swarm Optimization(APSO)algorithm based on the Low Energy Adaptive Clustering Hierarchy(LEACH),Neighboring Based Energy Efficient Routing(NBEER),Cooperative Energy Efficient Routing(CEER),and Cooperative Relay Neighboring Based Energy Efficient Routing(CR-NBEER)techniques.With the help of APSO in the implementation of the WSN,the main methodology of this article has taken place.The simulation findings in this study demonstrated that the suggested approach uses less energy,with respective energy consumption ranges of 0.1441 to 0.013 for 5 CH,1.003 to 0.0521 for 10 CH,and 0.1734 to 0.0911 for 15 CH.The sending packets ratio was also raised for all three CH selection scenarios,increasing from 659 to 1730.The number of dead nodes likewise dropped for the given combination,falling between 71 and 66.The network lifetime was deemed to have risen based on the results found.A hybrid with a few valuable parameters can further improve the suggested APSO-based protocol.Similar to underwater,WSN can make use of the proposed protocol.The overall results have been evaluated and compared with the existing approaches of sensor networks.

Accelerated Primal-Dual Projection Neurodynamic Approach With Time Scaling for Linear and Set Constrained Convex Optimization Problems

The Nesterov accelerated dynamical approach serves as an essential tool for addressing convex optimization problems with accelerated convergence rates.Most previous studies in this field have primarily concentrated on unconstrained smooth con-vex optimization problems.In this paper,on the basis of primal-dual dynamical approach,Nesterov accelerated dynamical approach,projection operator and directional gradient,we present two accelerated primal-dual projection neurodynamic approaches with time scaling to address convex optimization problems with smooth and nonsmooth objective functions subject to linear and set constraints,which consist of a second-order ODE(ordinary differential equation)or differential conclusion system for the primal variables and a first-order ODE for the dual vari-ables.By satisfying specific conditions for time scaling,we demonstrate that the proposed approaches have a faster conver-gence rate.This only requires assuming convexity of the objective function.We validate the effectiveness of our proposed two accel-erated primal-dual projection neurodynamic approaches through numerical experiments.

Almost Sure Convergence of Proximal Stochastic Accelerated Gradient Methods

Proximal gradient descent and its accelerated version are resultful methods for solving the sum of smooth and non-smooth problems. When the smooth function can be represented as a sum of multiple functions, the stochastic proximal gradient method performs well. However, research on its accelerated version remains unclear. This paper proposes a proximal stochastic accelerated gradient (PSAG) method to address problems involving a combination of smooth and non-smooth components, where the smooth part corresponds to the average of multiple block sums. Simultaneously, most of convergence analyses hold in expectation. To this end, under some mind conditions, we present an almost sure convergence of unbiased gradient estimation in the non-smooth setting. Moreover, we establish that the minimum of the squared gradient mapping norm arbitrarily converges to zero with probability one.

The Accelerated Expansion of the Universe in the Light of the Maximum Ordinality Principle

The main aim of the paper is to present (and at the same time offer) a differ-ent perspective for the analysis of the accelerated expansion of the Universe. A perspective that can surely be considered as being “in parallel” to the tradition-al ones, such as those based, for example, on the hypotheses of “Dark Matter” and “Dark Energy”, or better as a “com-possible” perspective, because it is not understood as being “exclusive”. In fact, it is an approach that, when con-firmed by experimental results, always keeps its validity from an “operative” point of view. This is because, in analogy to the traditional perspectives, on the basis of Popper’s Falsification Principle the corresponding “Generative” Logic on which it is based has not the property of the perfect induction. The basic difference then only consists in the fact that the Evolution of the Universe is now modeled by considering the Universe as a Self-Organizing System, which is thus analyzed in the light of the Maximum Ordinality Principle.

Optimum Constant-stress Plan for Accelerated Life Test with Censoring Ⅱ

In this paper, we obtain the optimum plan by discussing a constant-stress accelerated life test (ALT) satisfying the condition (3.3) at k stresses under an exponential distribution.

An accelerated method to evaluate thymopentin release from microspheres in vitro

To design an accelerated method to evaluate thymopentin release from PLGA microspheres in vitro. Microspheres were prepared by double emulsion technique, using poly（lactide-co-glycolide） （PLGA） as carrier. At higher medium temperature （45℃, 50℃ and 55℃）, an accelerated release testing in short time was studied and correlated with the conventional release （37℃） in vitro. The release in vitro of thymopentin from PLGA microspheres at 45 ℃, 50℃ and 55℃ was significantly accelerated （P 〈 0.05）. In particular, at 50℃, an accelerated release （30 h） of the hydrophilic peptide from the PLGA matrix was achieved and correlated well with the conventional release （30 d）. An accelerated release testing in vitro at higher temperature could be used to monitor thymopentin release from PLGA microspheres.

An Accelerated Simulation Method for ELDRS of Bipolar Operational Amplifiers Using a Dose-Rate Switching Experiment

Through different dose-rate switching evaluation methods,the radiation-response rules of operational amplifiers are studied when the irradiation dose rate is switched from high to low under different radiation temperatures and total doses. The experimental results indicate that the response characteristics could be affected by the switching total doses, irradiation temperatures,and dose rates individually or together. Accelerated evaluation on the ELDRS can be realized by adopting a proper dose-rate switching method. Meanwhile, the irradiation time can also be reduced. Finally, the mechanisms of the difference between various radiation responses are analyzed.

Negative effect improvement of accelerated curing on chloride penetration resistance of ordinary concrete

Four mineral admixture concrete specimens werefabricated to study the negative effect improvements ofaccelerated curing on the chloride penetration resistance ofordinary concrete. After reaching different initial strengths, the specimens were placed in 40, 60, or 80 t water tanks foraccelerated curing. The Coulomb values of the specimens weemeasured with ASTM C1202 experiment at 28, 100, 200, ad300 d. Partial specimens were also selected for rapid chlorideion migration coefficient and mercury intrusion porosimetryexperiments. The experimental results show that theaccelerated curing for ordinary concrete linealy deterioratesthe chloride penetration resistance, whereas the incorporationof mineral admixtures improves the concrete microscopic pore-structures and negative effects. An upper temperature limit of60 t of the accelerated curing is suitable for obtainingsuperior chloride penetration resistance for the mineraladmixture concrete. Pre-curing at a normal temperature of 20t is beneficial for improving the negative effect, which isalso aieviated with increasing testing age as a result of thesuccessive hydration of binder materials in concrete.

High corrosion resistance of electroless Ni-P with chromium-free conversion pre-treatments on AZ91D magnesium alloy

Phosphate-manganese, tannic acid and vanadium conversion coatings were proposed as an effective pre-treatment layer between electroless Ni-P coating and AZ91D magnesium alloy substrate to replace the traditional chromate plus HF pre-treatment. The electrochemical results show that the chrome-free coatings plus electroless Ni-P coating on the magnesium alloy has the lowest corrosion current density and most positive corrosion potential compared with chromate plus electroless Ni-P coating on the magnesium alloy. These proposed pre-treatment layers on the substrate reduce the corrosion of magnesium during plating process, and reduce the potential difference between the matrix and the second phase. Thus, an electroless Ni-P coating with fine crystalline and dense structure was obtained, with preferential phosphorus content, low porosity, good corrosion-resistance and strengthened adhesion than the chromate plus electroless Ni-P.

Accelerated Degradation Reliability Modeling and Test Data Statistical Analysis of Aerospace Electrical Connector

As few or no failures occur during accelerated life test,it is difficult to assess reliability for long-life products with traditional life tests.Reliability assessment using degradation data of product performance over time becomes a significant approach.Aerospace electrical connector is researched in this paper.Through the analysis of failure mechanism,the performance degradation law is obtained and the statistical model for degradation failure is set up; according to the research on statistical analysis methods for degradation data,accelerated life test theory and method for aerospace electrical connector based on performance degradation is proposed by improving time series analysis method,and the storage reliability is assessed for Y11X series of aerospace electrical connector with degradation data from accelerated degradation test.The result obtained is basically consistent with that obtained from accelerated life test based on failure data,and the two estimates of product＇s characteristic life only have a difference of 8.7%,but the test time shortens about a half.As a result,a systemic approach is proposed for reliability assessment of highly reliable and long-life aerospace product.

Step-stress Accelerated Degradation Test Modeling and Statistical Analysis Methods

In order to get a rapid assessment on the storage reliability of high-reliable and long-life products within the storage period, accelerated degradation test data with a large amount of reliability information of product is adopted. Conducting a constant-stress accelerated degradation test（CSADT） is generally very costly as it requires a large sample size and long time for test. To overcome this problem, it is necessary to carry out research on modeling and statistical analysis methods of step-stress accelerated degradation test （SSADT）. Taking electrical connectors as the object, a research is conducted on statistical model and assessment method for SSADT. On the basis of mixed-effect degradation path model, the statistical model of SSADT for electrical connectors is presented, the maximum likelihood method for SSADT data based on mixed-effect degradation model is proposed. SSADT accelerated by temperature stress is conducted to Y11X-1419 type of electrical connectors, and the storage reliability is assessed with the SSADT data. Compared with the result obtained from accelerated life test, the reliability estimation of 32-year storage period for electrical connectors obtained from S SADT data only have a difference of 0.869%, which validates the accuracy of the degradation model and the feasibility of the test data statistic analysis method put forward.

Simultaneous modulated accelerated radiation therapy for esophageal cancer:A feasibility study

AIM: To establish the feasibility of simultaneous modulated accelerated radiation therapy (SMART) in esophageal cancer (EC).

Residual lifetime prediction model of nonlinear accelerated degradation data with measurement error

For the product degradation process with random effect (RE), measurement error (ME) and nonlinearity in step-stress accelerated degradation test (SSADT), the nonlinear Wiener based degradation model with RE and ME is built. An analytical approximation to the probability density function (PDF) of the product's lifetime is derived in a closed form. The process and data of SSADT are analyzed to obtain the relation model of the observed data under each accelerated stress. The likelihood function for the population-based observed data is constructed. The population-based model parameters and its random coefficient prior values are estimated. According to the newly observed data of the target product in SSADT, an analytical approximation to the PDF of its residual lifetime (RL) is derived in accordance with its individual degradation characteristics. The parameter updating method based on Bayesian inference is applied to obtain the posterior value of random coefficient of the RL model. A numerical example by simulation is analyzed to verify the accuracy and advantage of the proposed model.