Transmission Characteristic Simulation of High Frequency Acousto-Optic Modulators

The way by which one can make sure the operating mode of the modulation is by observing the Comsol results of the designed model of proposed acousto-optic modulator (AOM). These results include the pressure distribution, sound pressure distribution, stress distribution at piezoelectric, far-field analysis that describes the diffracted light orders, and electric potential versus light frequency. Throughout the simulating process of modulator operating using Comsol, it begins when the RF is power by a voltage of 100 V, the light is then split into first ordered diffraction, which implies that the modulator is in the operating mode. The use of semiconductor materials is due to its smaller gap that easily transfers the energy that leads to generating first order diffraction when they provided a voltage power. It mentioned that zero order diffraction indicates the modulator does not run;other orders are appearing with increasing the frequency of light leading to decrease of the efficiency of the modulator performance.

A High-Performance Silicon Electro-Optic Phase Modulator with a Triple MOS Capacitor

We propose and analyze a novel Si-based electro-optic modulator with an improved metal-oxide-semiconductor （MOS） capacitor configuration integrated into silicon-on-insulator （SOl）. Three gate-oxide layers embedded in the silicon waveguide constitute a triple MOS capacitor structure, which boosts the modulation efficiency compared with a single MOS capacitor. The simulation results demonstrate that the Vπ Lπ product is 2. 4V · cm. The rise time and fall time of the proposed device are calculated to be 80 and 40ps from the transient response curve, respectively,indicating a bandwidth of 8GHz. The phase shift efficiency and bandwidth can be enhanced by rib width scaling.

Modulation Recognition with Frequency Offset and Phase Offset over Multipath Channels

Modulation recognition becomes unreliable at low signal-to-noise ratio(SNR)over fading channel.A novel method is proposed to recognize the digital modulated signals with frequency and phase offsets over multi-path fading channels in this paper.This method can overcome the effects of phase offset,Gaussian noise and multi-path fading.To achieve this,firstly,the characteristic parameters search is constructed based on the cyclostationarity of received signals,to overcome the phase offset,Gaussian white noise,and influence caused by multi-path fading.Then,the carrier frequency of the received signal is estimated,and the maximum characteristic parameter is searched around the integer multiple carriers and their vicinities.Finally,the modulation types of the received signal with frequency and phase offsets are classified using decision thresholds.Simulation results demonstrate that the performance of the proposed method is better than the traditional methods when SNR is over 5dB,and that the proposed method is robust to frequency and phase offsets over multipath channels.

Fast generation of controllable equal-intensity four beams based on isosceles triangle multilevel phase grating realized by liquid crystal spatial light modulator

Liquid crystal spatial light modulator （LCSLM） realizing equal-intensity multiple beams often has some features, i.e., phase valley between two adjacent pixels, flybaek region when phase decreases immediately from 2~r to 0, and inevitable backplane curvature, which are different from those of most conventional diffractive optical elements （DOEs）, such as static DOEs. For optimal intensity uniformity, equal-intensity multi-beam generation must be considered for these artifacts. We present a tunable-grating method in which the intensity uniformity can be improved by considering the LCSLM artifacts. For instance, tuning phase modulation depth of the grating, called isosceles triangle multilevel phase grating （ITMPG）, can be used not only to improve the intensity uniformity, but also to fast steer four beams with narrow beamwidths, determined by the same effective aperture of ITMPG. Improved intensity uniformity and high relative diffraction efficiency are demonstrated through experiments with phase-only LCSLM.

A fractional frequency divider based on phase switching and negative feedback delta-sigma modulator for MMMS applications

A fractional frequency divider based on phase switching and negative feedback delta-sigma modulator(NF-DSM) is presented. The phase switching circuit, realized by switching 8 signals generated by a divider-by-4 circuit, is adopted to reduce the frequency division step. The NF-DSM, which can obtain smooth output spectra, is proposed to generate the fractional part of the division ratio, moreover, the integer part of the division ratio is realized by a divider-by-2/3 circuit chain. Fabricated in TSMC 0.18 μm RF CMOS technology, the fractional frequency divider achieves a measured operation frequency from 0.5 GHz to 8 GHz. With a 1.8 V supply voltage, the maximum current consumption of the whole divider is 17.5 mA, and the chip area is 0.58 mm^2, including the pads.

Acousto-optic modulator-based bi-frequency interferometer for quantum technology

We demonstrate a high-performance acousto-optic modulator-based bi-frequency interferometer,which can realize either beating or beating free interference for a single-photon level quantum state.Visibility and optical efficiency of the interferometer are(99.5±0.2)%and(95±1)%,respectively.The phase of the interferometer is actively stabilized by using a dithering phase-locking scheme,where the phase dithering is realized by directly driving the acousto-optic modulators with a specially designed electronic signal.We further demonstrate applications of the interferometer in quantum technology,including bi-frequency coherent combination,frequency tuning,and optical switching.These results show the interferometer is a versatile device for multiple quantum technologies.

Bunching enhancement for coherent harmonic generation by using phase merging effects

In this paper,promising but simple schemes are investigated to enhance the micro-bunching of relativistic electron beams for coherent harmonic generation(CHG)by using phase merging effects.In contrast to the standard CHG scheme,two specially designed dispersion sections(DSs)are adopted with the DS-modulator–DS configuration.The phase space of the e beam is appropriately coupled in the first DS,and the electrons within one seed wavelength can merge to the same phase with a matched second DS.Micro-bunching of the e beam can thus be enhanced by a large margin with much higher-harmonic components.Taking e beams from laser wakefield accelerators(LWFAs)as an example,start-to-end simulations are performed to show the effectiveness and robustness of the proposed schemes with several configurations.The beam current can be optimized to several tens to hundreds of kiloamperes,and the radiation power reaches hundreds of megawatts in the extreme ultraviolet regime within a 3.5 m-long beamline.The proposed schemes offer new opportunities for future compact free-electron lasers driven by LWFAs and provides prospects for truly compact and widely applicable systems.

Security-Enhanced Directional Modulation Based on Two-Dimensional M-WFRFT

Directional modulation(DM)is one of the most promising secure communication techniques.However,when the eavesdropper is co-located with the legitimate receiver,the conventional DM has the disadvantages of weak anti-scanning capability,anti-deciphering capability,and low secrecy rate.In response to these problems,we propose a twodimensional multi-term weighted fractional Fourier transform aided DM scheme,in which the legitimate receiver and the transmitter use different transform terms and transform orders to encrypt and decrypt the confidential information.In order to further lower the probability of being deciphered by an eavesdropper,we use the subblock partition method to convert the one-dimensional modulated signal vector into a twodimensional signal matrix,increasing the confusion of the useful information.Numerical results demonstrate that the proposed DM scheme not only provides stronger anti-deciphering and anti-scanning capabilities but also improves the secrecy rate performance of the system.

Transmission Performance of the Optical Millimeter-wave Up-conversion Link Using a Phase Modulator

Numerically analyzed is the transmission performance of the optical millimeter （mm）-wave generated by frequency up-conversion via a phase modulator along the dispersive fiber. 60 GHz ram-wave subcarrier（SC） signals can be obtained after fiber transmission, simultaneously, the phase-modulated signals can be converted to the intensity-modulated ones. The numerical results show that the optical ram-wave at fading loops has better performance, and the eye diagram still keeps open when optical mm-wave signal is transmitted over 98 km.

Optimizing effective phase modulation in coupled double quantum well Mach–Zehnder modulators

We report optimal phase modulation based on enhanced electro–optic effects in a Mach–Zehnder（MZ） modulator constructed by AlGaAs/GaAs coupled double quantum well（CDQW） waveguides with optical gain. The net change of refractive indexes between two arms of the CDQW MZ modulator is derived by both the electronic polarization method and the normal-surface method. The numerical results show that very large refractive index change over 10^（-1） can be obtained, making the phase modulation in the CDQW MZ modulator very highly efficient. It is desirable and important that a very small voltage-length product for π phase shift, V_π× L_0= 0.0226 V · mm, is obtained by optimizing bias electric field and CDQW structural parameters, which is about seven times smaller than that in single quantum-well MZ modulators.These properties open an avenue for CDQW nanostructures in device applications such as electro–optical switches and phase modulators.

Phase Modulation Characteristics of Spatial Light Modulator and the System for Its Calibration

The phase modulation characteristics of liquid crystal SLM （spatial light modulator） and the system for calibrating are proposed. Michelson interferometer is employed for measuring the modulation properties of device. A system interface for operating SLM is designed with VC＋＋ compiler. The initial distortion phase is determined by measuring the reflective interference, and modulation of device is compensated by using our system. By using the LUT （lookup table） data provided by manufacture the wavelength disperse calibration is also achieved successfully.

A Pulse Width Modulation Scheme With Zero-sequence Voltage Injection for Single Phase Three-level NPC Rectifiers

直流侧中点电位电压偏移是多电平中性点钳位型变流器的主要缺点。以单相三电平NPC整流器为研究对象，以实现直流侧中点电位无漂移为控制目标，以传统的单相三电平单极性载波脉宽调制方法为基础，首先提出一种基于零序电压分量注入的载波脉宽调制算法；然后在此基础上给出基于零序电压分量极限值注入的载波脉宽调制算法；并给出这2种方法的零序电压分量的设计方案；最后，对这2种方法进行了详细的理论分析、计算机仿真和1kW样机实验对比验证。研究结果表明：所提出的2种算法都能有效实现直流侧中点电位平衡控制，其中基于零序电压分量极限值注入的载波调制算法的中点电位控制具有更快动态响应速度，且其网侧电流的高次谐波主要分布在开关频率附近；而基于零序电压分量注入的载波调制算法的网侧电流高次谐波主要分布在2倍开关频率附近。但是在一个调制信号周期内，基于零序电压分量极限值注入的载波调制算法的开关切换次数比基于零序电压分量注入的载波调制算法低25％左右。

Experimental implementation of phase triplicator gratings in a spatial light modulator

In this work,we compare different methods for implementing a triplicator,a phase grating that generates three equiintense diffraction orders.The design with optimal efficiency features a continuous phase profile,which cannot be easily reproduced,and is typically affected by quantization.We compare its performance with binary and sinusoidal phase profiles.We also analyze the effect of quantizing the phase levels.Finally,a random approach is adopted to eliminate the additional harmonic orders.In all cases,a liquid-crystal-on-silicon spatial light modulator is employed to experimentally verify and compare the different approaches.

Influence of random phase modulation on the imaging quality of computational ghost imaging

In this paper, we investigated phase modulation-based computational ghost imaging. According to the results of numerical simulations, we found that the range of the random phase affects the quality of the reconstructed image. Besides,compared with those amplitude modulation-based computational ghost imaging schemes, introducing random phase modulation into the computational ghost imaging scheme could significantly improve the spatial resolution of the reconstructed image, and also extend the field of view.

Parallel generation of low-correlation wideband complex chaotic signals using CW laser and external-cavity laser with self-phase-modulated injection

A novel scheme for generating optical chaos is proposed and experimentally demonstrated,which supports to simultaneously produce two low-correlation chaotic signals with wideband spectrum and suppressed time-delay-signature(TDS).In the proposed scheme,we use the output of an external-cavity semiconductor laser(ECSL)as the driving signal of a phase modulator to modulate the output of a CW laser.Then the phase-modulated continuous-wave(CW)light is split into two parts,one is injected back into the ECSL that outputs one chaotic signal,while the other part is passed through a dispersion module for generating another chaotic signal simultaneously.The experimental results prove that the proposed scheme has three merits.Firstly,it can improve the bandwidth of ECSL-based chaos by several times,and simultaneously generate another wideband flat-spectrum chaotic signal.Secondly,the undesired TDS characteristics of the simultaneously-generated chaotic signals can be efficiently suppressed to an indistinguishable level within a wide parameter range,as such the complexities of the chaotic signals are considerably high.Thirdly,the correlation coefficient between these two simultaneously-generated chaotic signals is smaller than 0.1.The proposed scheme provides an attractive solution for parallel multiple chaos generation,and shows great potential for multiple channel chaos communications and multiple random bit generations.

Phase-matching analysis of four-wave mixing induced by modulation instability in a single-mode fiber

Four-wave mixing induced by modulation instability in a single-mode fiber is analyzed from the phase-matching point of view. For the two-channel transmission, a method is proposed to select the four-wave-mixing-induced sidebands, which is based on the proper use of a continuous-wave and a pulse as light sources. We find that a mass of sidebands are generated in the modulation instability resonance region, and the power of the sideband increases with not only the peak power of the pump pulse but also the continuous-wave power which acts as a seed. The research will provide guidance for fiber communication and sensing systems using wavelength division multiplexing technology.

An all-optical phase detector by amplitude modulation of the local field in a Rydberg atom-based mixer

Recently,a Rydberg atom-based mixer was developed to measure the phase of a radio frequency(RF)field.The phase of the signal RF(SIG RF)field is down-converted directly to the phase of a beat signal created by the presence of a local RF(LO RF)field.In this study,we propose that the Rydberg atom-based mixer can be converted to an all-optical phase detector by amplitude modulation(AM)of the LO RF field;that is,the phase of the SIG RF field is related to both the amplitude and phase of the beat signal.When the AM frequency of the LO RF field is the same as the frequency of the beat signal,the beat signal will further interfere with the AM of the LO RF field inside the atom,and then the amplitude of the beat signal is related to the phase of the SIG RF field.The amplitude of the beat signal and the phase of the SIG RF field show a linear relationship within the range of 0 toπ/2 when the phase of the AM is set with a differenceπ/4 from the phase of the LO RF field.The minimum phase resolution can be as small as 0.6°by optimizing the experimental conditions according to a simple theoretical model.This study will expand and contribute to the development of RF measurement devices based on Rydberg atoms.

Equalization for continuous phase modulation over frequency-selective fading channels

This paper presents an equalization algorithm for continuous phase modulation （CPM） over frequency-selective channels. A specific training sequence is first embedded in each data packet. By recursive least-squares （RLS） estimation, the channel information parameters can be acquired, and a fractionally Simulation results show that the proposed algorithm can acquire the spaced equalizer performs joint decoding and equalization. channel information parameters rapidly and accurately, and that the fractionally spaced equalizer can eliminate the intersymbol interference （ISI） effectively, and is not sensitive to timing inaccuracy, so this algorithm can be exploited for demodulation system in burst mode.

SERIALLY CONCATENATED CONTINUOUS PHASE MODULATION WITH REDUCED ITERATIVE DEMODULATION AND DETECTION

A reduced state Soft Input Soft Output (SISO) a posteriori probability algorithm for Seri-ally Concatenated Continuous Phase Modulation (SCCPM) is proposed in this paper. Based on the Reduced State Sequence Detection (RSSD),it has more general form compared with other reduced state SISO algorithms. The proposed algorithm can greatly reduce the state number,thus leads to the computation complexity reduction. It also minimizes the degradation in Euclidean distance with decision feedback in the reduced state trellis. Analysis and simulation results show that the perform-ance degradation is little with proper reduction scheme.

Spectral analysis of the UFBG-based acousto optical modulator in V–I transmission matrix formalism

In this study, the V-I transmission matrix formalism （V-I method） is proposed to analyze the spectrum characteristics of the uniform fiber Bragg grating （FBG）-based acousto--opfic modulators （UFBG-AOM）. The simulation results demon- strate that both the amplitude of the acoustically induced strain and the frequency of the acoustic wave （AW） have an effect on the spectrum. Additionally, the wavelength spacing between the primary reflectivity peak and the secondary reflectivity peak is proportional to the acoustic frequency with the ratio 0.1425 nm/MHz. Meanwhile, we compare the amount of calculation. For the FBG whose period is M, the calculation of the V-I method is 4 × （2M-l） in addition/subtraction, 8 × （2M - 1） in multiply/division and 2M in exponent arithmetic, which is almost a quarter of the multi-film method and transfer matrix （TM） method. The detailed analysis indicates that, compared with the conventional multi-film method and transfer matrix （TM） method, the V-I method is faster and less complex.