Removal of manganese from waste water by complexation-ultrafiltration using copolymer of maleic acid and acrylic acid

Copolymer of maleic acid and acrylic acid （PMA-100）, combining with polyvinyl butyral （PVB） ultrafiltration membrane was used for the removal of Mn（II） from waste water by complexation-ultrafiltration. The carboxylic group content of PMA-100 and the rate of complexation reaction were measured. Effects of the mass ratio of PMA-100 to Mn（II） （n）, pH, background electrolyte, etc on the rejection rate （R） and permeate flux （J） were investigated. The results show that carboxylic group content of PMA-100 is 9.5 mmol/g. The complexation of Mn（II） with PMA-100 is rapid and completed within 5 min at pH 6.0. Both R and J increase with pH increasing in the range of 2.5-7.0, and R increases with the increase of n at pH 6.0 while J is little affected. The background electrolyte leads to the decrease of R, and CaCl2 has much greater effect on R than NaCl at the same ionic strength.

Synthesis and Characterization of Chitosan-g-poly- (D, L-lactic acid) Copolymer

Biodegradable chitosan-g-poly (D, L-lactic acid) copolymers were prepared via two methods. (1) The lactide was grafted onto hydroxyl groups of chitosan by using macromolecular initiator sodium of trimethylsilyl-chitosan, (2) poly (D,L-lactic acid)(PLA) with low molecular weight can be linked to the amino group by coupling activated PLA to trimethylsilyl-chitosan. Two graft copolymers had hydrophilic-hydrophobic character and can be applied as carriers for drug delivery.

PHOTO-INDUCED DOPED POLYANILINE BY THE VINYLIDENE CHLORIDE AND METHYL ACRYLATE COPOLYMER AS PHOTO ACID GENERATOR

The emeraldine base form of polyaniline (PANI) can be doped by a photo-induced doping method. In this method a. copolymer of vinylidene chloride and methyl acrylate (VCMAC) was used as photo acid generator which can release proton when it is exposed to ultraviolet light (lambda = 254 nm). The structure of PANI-VCMAC system before and after irradiation was characterized by elemental analysis, IR, XTP, anti SEM images. Results obtained indicate that the photo-induced doping characteristics, such as doping position and type of charge carriers, are similar to that of PANI doped with HCl. The poor room-temperature conductivity (similar to 10-S-5/cm) of PANI-VCMAC system after irradiation may be due to low doping degree (similar to pH=3) and the difference in morphology as compared with PANI-HCl film.

Intermolecular Acid-Base-Pairs Containing Poly(p-Terphenyl-co-lsatin Piperidinium)for High Temperature Proton Exchange Membrane Fuel Cells

How to optimize and regulate the distribution of phosphoric acid in matrix,and pursuing the improved electrochemical performance and service lifetime of high temperature proton exchange membrane(HT-PEMs)fuel cell are significant challenges.Herein,bifunctional poly(p-terphenyl-co-isatin piperidinium)copolymer with tethered phosphonic acid(t-PA)and intrinsic tertiary amine base groups are firstly prepared and investigated as HT-PEMs.The distinctive architecture of the copolymer provides a well-designed platform for rapid proton transport.Protons not only transports through the hydrogen bond network formed by the adsorbed free phosphoric acid(f-PA)anchored by the tertiary amine base groups,but also rely upon the proton channel constructed by the ionic cluster formed by the t-PA aggregation.Thorough the design of the structure,the bifunctional copolymers with lower PA uptake level(<100%)display prominent proton conductivities and peak power densities(99 mS cm^(-1),812 mW cm^(-2)at 160℃),along with lower PA leaching and higher voltage stability,which is a top leading result in disclosed literature.The results demonstrate that the design of intermolecular acid-base-pairs can improve the proton conductivity without sacrificing the intrinsic chemical stability or mechanical property of the thin membrane,realizing win-win demands between the mechanical robustness and electrochemical properties of HT-PEMs.

SYNTHESIS AND THERMAL PROPERTIES OF A NEW CHOLIC ACIDCONTAINING COPOLYMER

A new copolymer was synthesized by free radical polymerization in solution from methyl 3α-methylacryloyl-7α, 12α-dihydroxy-5β-cholan-24-oate (MACAME) and maleic anhydride (MAN). The copolymer was characterized by FT-IR and functional group analysis. The reactivity ratios of the two monomers were estimated [r_1 = 11.6 (MACAME), r_2 = 0.01(MAN)] by conducting a series of copolymerizations with a variety of monomer feed compositions and analyzing thecopolymer composition. Thermogravimetric and differential scanning calorimetric analyses of the samples indicate that thecopolymer possesses good thermal stability. The temperature at which the copolymer samples experienced a 10% weight loss(T_(WL)) is over 287℃, and the T_g ranged from 174 to 185℃ for the copolymers.

SELECTIVE SEPARATION OF WATER-ETHANOL MIXTURES THROUGH COPOLYMERIC MEMBRANES: Ⅰ. ACRYLIC ACID AND ACRYLONITRILE COPOLYMER AND ITS IONIZED MEMBRANES

The copolymer of acrylic acid and acrylonitrile has been synthesized and pervaporation properties of the copolymeric membranes have been investigated. In order to elucidate the influence of membrane-permeate interaction on the pervaporation of water-ethanol mixtures and to prepare much improved membranes, the membranes have been treated with alkali metal, alkali earth metal and transition metal salt aqueous solutions. The treated membranes (ionized membranes) exhibited higher separation factors than the untreated membranes. The separation factors of various alkali metal cation membranes decreased in the following order : Li^+>Na^+>K^+, and the permeation rates showed an opposite tendency. The dependence of pervaporation behavior on the copolymer composition ,feed concentration and operating temperature have been studied with both ionized and non-ionized membranes. The apparent activation energies of water and ethanol permeation were calculated.

Influence of Block Copolymer on Formation and Acid Resistant Properties of Hybrid CaCO_3 Particles

Block copolymer polystyrene-b-poly（acrylic acid）（PS-b-PAA） was used as structural template for the synthesis of CaCO3 microparticles. Through this procedure, acid resistant hybrid CaCO3 micro- spheres were obtained. Acid resistant properties of this type of hybrid CaCO3 were studied. Size measurement shows that the acid resistant properties of the hybrid particles are different in different solutions, such as HCl, EDTA, and H2SO4 solutions.

SYNTHESIS OF NOVEL BLOCK COPOLYMERS OF POLY(3-HYDROXYBUTYRIC ACID)WITH POLY(ETHYLENE GLYCOL)THROUGH ANIONIC POLYMERISATION

A novel kind of copolymer with ABA-type block structure was synthesized by anionic ring-opening polymerization of beta-butyrolactone (beta-BL) in the presence of a PEG-based dicarboxylates as macroinitiators which were prepared by the esterification of aliphatic cyclic anhydride and poly(ethylene glycol) (PEG) oligomers (M-n = 2000, 4000 and 6000) and conversion of potassium dicarboxylates. The resultant copolymers as well as the intermediates were characterized by IR, H-1-NMR and GPC.

A NOVEL COPOLYMER-BOUND CIS-DICARBONYLRHODIUM COMPLEX FOR THE CARBONYLATION OF METHANOL TO ACETIC ACID AND ACETIC ANHYDRIDE

A series of porous microspheres of linear and ethylene diacrylate (M') cross-linked copolymers of 2-vinylpyridine (V) and methyl acrylate (M) reacted with tetracarbonyldichlorodirhodium to form a series of cis-dicarbonylrhodium chelate complex (MVRh and MVM 'Rh). They are thermally stable yet very reactive in the carbonylation of methanol to acetic acid, and of methanol-acetic acid mixture to acetic acid and acetic anhydride with a selectivity of 100% under relatively mild and anhydrous conditions.

Preparation of Poly ( L-lactic acid ) / Vermiculites Composites by in situ Copolymerization of Lactic Acid and Hydroxylic Vermiculites

L-lactic acid (L-LA) based copolymer/hydroxylation vermiculites composites (PLLA-co-bis A/HVMTs) were prepared by in situ reaction among L-LA, adipic acid, and hydroxylation lamellar vermiculites (HVMTs) using bisphenol-A epoxy resin as chain extending agent. HVMTs were obtained by sulfuric acid-leaching of lamellar vermiculites (VMTs). The effects of sulfuric acid leaching on the VMTs structure were characterized by X-ray diffraction (XRD), 29Si magic-angle spinning nuclear magnetic resonance(29Si NMR), Fourier transform infrared spectroscopy (FTIR), field emission scanning electron microscopy (FE-SEM), and thermogravimetric analysis (TGA). FTIR, FE-SEM, and TGA were used to characterize the reaction activity of HVMTs. The results indicated that VMTs with increased hydroxyl groups had been successfully obtained and could react with -COOH of the reaction system. The amount of L-LA based copolymer grafted on the surface of HVMTs was more than 22%. The onset decomposition temperature of L-LA based copolymer grafted on the surface of HVMTs was 30℃ higher than that of free L-LA based copolymer.

The Optimized Synthesis of Starch-g-Lactic Acid Copolymer with High Grafting Degree Catalyzed by Sulfuric Acid

The starch-g-lactic acid copolymer was synthesized with catalysis of sulfuric acid by onestep process, and the structure of starch-g-lactic acid copolymer was characterized by means of IR, 13C-NMR, HMBC, XRD, and SEM. The experimental results show that the maximum grafting degree of starch can reach 75% when the starch-g-lactic acid copolymer is activated at 80 ℃ for 2 h and reacted with lactic acid at 90 ℃ for 4 h in vacuum.

An Approach to the Flame Retardancy of EVA Copolymer by Plasma Treatmentc2

An attempt was made in the paper aiming at imparting flame retardancy to polymers by plasma grafting technique Based on EVA copolymers with different VA contents the author tried to use the Ar plasma followed by grafting with/without subsequent saponification and metal ion exchange expediting the charring of polymers upon heationg Characterization of the flammability of the plasma treated EVA copolymers grafted with acrylic monomers(MAA,AA and AAm)indicates that this approach turns out to be a promising way and worthy doing whatever in research and/or applications

Synthesis and application of lignin-based copolymer LSAA on controlling non-point source pollution resulted from surface runoff

In this article,alkali lignin separated from paper pulp waste was grafted into a novel copolymer LSAA (a copolymer of lignin,starch, acrylamide,and acrylic acid).Its practical application effect and environmental safety were studied.The results of field simulation experiment indicated that the application of LSAA significantly affected the output of the runoff and pollutants.The runoff quantity was decreased by 16.67%-47.00%and the loads of total suspended solids (TSS),chemical oxygen demand (COD),total nit...

Comparison of selective flocculation of low grade goethitic iron ore fines using natural and synthetic polymers and a graft copolymer

This study aims to beneficiate low grade goethitic iron ore fines using a selective flocculation process. Selective flocculation studies were conducted using different polymers such as starch amylopectin(AP), poly acrylic acid(PAA), and a graft copolymer(AP-g-PAA). The obtained results were analyzed; they indicate the enhancement of the iron ore grade from 58.49% to 67.52% using AP-g-PAA with a recovery of 95.08%. In addition, 64.45% Fe with a recovery of 88.79% was obtained using AP. Similarly, using PAA, the grade increased to 63.46% Fe with a recovery of 82.10%. The findings are also supported by characterizing concentrates using X-ray diffraction(XRD) and electron probe microanalysis(EPMA) techniques.

Weavability of β-Hydroxybutyrate and β-Hydroxyvalerate Copolymers( PHBV ) /PLA Used in Artificial Blood Vessels

The β-hydroxybutyrate and β-hydroxyvalerate copolymers( PHBV) /polylactic acid( PLA) is a new biocompatible material,which is developed through bacterial fermentation in vivo systems.The PHBV / PLA material could be used to make continuous filaments.However,features of artificial blood vessels,especially small diameter vascular grafts made of PHVB / PLA materials are not known.This research are to evaluate and improve weavability of the PHBV / PLA material, and to explore feasibility of using it in artificial blood vessels.Preliminary results showed that weavability of PHBV / PLV was not good,but its weavability could be improved by using methods of weak chemical,such as sizing.In this research,scanning electron microscope( SEM) was adopted to evaluate weavability of PHBV / PLV after sizing and observe surfaces of yarns and fabrics.Also,in order to set proper parameters in heat settings,differential scanning calorimetry( DSC) was used to identify glass transition temperature.

Synthesis and Characterization of Degraded Gelatin Grafted Poly(ε-caprolactone) Copolymers

Hydrophilic degraded gelatin was modified with hydrophobic poly(ε-caprolactone) (PCL) via a chemical grafting route.Firstly,PCL with one hydroxyl end group was prepared by the ring-opening polymerization of εcaprolactone (ε-CL) with tin (Ⅱ) 2-ethylhexanoate as catalyst and n-butyl alcohol as initiator.Secondly,the PCL reacted with isophorone diisocyanate (IPDI) to prepare PCL with isocyanate functional group (PCL-NCO).Hydroxylamine was used to degrade gelatin by the cleavage between asparagine and glycine residues of gelatin.PCL-NCO reacted with the hydroxyl/amino groups of degraded gelatin in a homogeneous system and yielded the PCL modified gelatin copolymers.The gelatin grafted PCL copolymers were measured by means of XRD,FTIR,DSC and 1 H NMR.The results confirmed the conjugation of PCL onto gelatin chains.The PCL modified gelatin can be used as biomaterials owing to their biocompatibility and biodegradation.

Effect of Poly(ε-caprolactone-b-tetrahydrofuran)Triblock Copolymer Concentration on Morphological,Thermal and Mechanical Properties of Immiscible PLA/PCL Blends

In this study a low molecular weight triblock copolymer derived fromε-caprolactone and tetrahydrofuran was used as a non-reactive compatibilizer of immiscible PLA/PCL blends.Ternary blends with 0,1.5 wt%,3 wt%and 5 wt% copolymer and about 75 wt%PLA were prepared by single screw extrusion and characterized by scanning electron microscopy(SEM),differential scanning calorimetry(DSC),dynamic mechanical analysis(DMA),tensile and Izod impact testing.SEM micrographs showed that the size of the dispersed PCL domains was practically constant regardless of copolymer concentration.This result can be explained by the low shear rate employed during processing step and a decrease of PCL viscosity by presence of the triblock copolymer.However,when the copolymer concentration increased,strain at break of PLA/PCL blends also increased.PLA/PCL blend with 0 wt% copolymer presented 2%strain at break,whereas PLA/PCL blend with 5 wt%copolymer exhibited 90%.

Effect of the Side Chain Structure on Hydrolysis Degradation of Zinc Acrylate Copolymers

In this report,zinc acrylate copolymers were synthesized by used different organic acid as the side chain structure.These copolymers were further characterized by GPC,DSC and Water absorption analysis respectively,and then the effects of the chain structure of organic acid on hydrolysis degradation and copper release rate were also discussed.In the meantime,the result shows that the biocide release rate could be controlled by used different chain structure of organic acid.

Synthesis and Characterization of Novel Copolymers Based on 3(S)-Methyl-Morpholine-2,5-Dione

A series of novel copolymers were successfully synthesized by ring-opening polymerization （ROP） of 3 （S）-methyl-morpholine-2,5-dione （MMD） and 5-methyl-5-benzyloxycarbonyl-1,3-dioxan-2-one （MBC） using stan- nous octoate as catalyst. The copolymers were characterized by means of ~H-NMR and FT-IR spectroscopy. Gel permeation chromatography （GPC） test shows that the average-number relative molecular mass and average-weight rela- tive molecular mass slightly increase with the increase of MBC content in feed. The results of differential scanning calorimetry （DSC） demonstrate that the glass transition temperature of copolymers increases with the increase of MBC content in copolymers. The copolymers of MMD and MBC are amorphous copolymers, as indicated by DSC results, while the homopolymer of MMD is semicrystalline.

3D打印工艺参数对PLA/PTW共混物力学性能影响的研究

采用3D打印中的熔融沉积成型(FDM)工艺制备了聚乳酸/乙烯-丙烯酸丁酯-甲基丙烯酸缩水甘油酯共聚物(PLA/PTW),通过单因素实验探究了3D打印工艺参数(喷头温度、打印平台温度和打印速度)对PLA/PTW共混物力学性能的影响,并在此基础上设计了三因素三水平正交实验,优化了3D打印的工艺参数。结果表明,共混物的冲击强度和拉伸强度均随喷头温度的增加呈现先上升后下降、均随打印平台温度的增加而增加、均随打印速度的增加出现下降的趋势。各工艺参数对PLA/PTW共混物综合力学性能的影响从大到小依次为:喷头温度、打印速度、打印平台温度,且当喷头温度为210℃、打印平台温度为80℃以及打印速度为40 mm/s时,打印出的PLA/PTW共混物的综合力学性能最佳。