Acid mine drainage activation mechanism on lime-depressed pyrite flotation from copper sulfide ore

The lime-depressed pyrite from Cu differential flotation tailings with acid mine drainage(AMD)as a natural activator was recovered.The effect of AMD on lime-depressed pyrite flotation was investigated by a series of laboratory flotation tests and surface analytical techniques.Flotation test results indicated that AMD could effectively activate the pyrite flotation with a sodium butyl xanthate(SBX)collector,and a high-quality sulfur concentrate was obtained.Pulp ion concentration analysis results indicated that AMD facilitated desorption of Ca~(2+)and adsorption of Cu~(2+)on the depressed-pyrite surface.Adsorption measurements and contact angle analysis results confirmed that adding AMD improved the adsorption amount of SBX collector on the pyrite surface and increased the contact angle by 31°.Results of Raman spectroscopy and X-ray photoelectron spectroscopy analysis indicated that AMD treatment promoted the formation of hydrophobic species(S~0 hydrophobic entity and copper sulfides)and the removal of hydrophilic calcium and iron species on the pyrite surface,which reinforced the adsorption of collector.The findings of the present research provide important theoretical basis and technical support for a cleaner production of copper sulfide ores.

Activation of anthracite combustion by copper acetate:mechanism,effect of particle size and introduction method

This paper addressed the efect of copper acetate on the combustion characteristics of anthracite depending on the fractional composition of fuel and additive introduction method.Anthracite was impregnated with 5 wt%of Cu(CH_(3)COO)_(2)by mechanical mixing and incipient wetness impregnation.Four anthracite samples of diferent fraction with d<0.1 mm,d=0.1-0.5 mm,d=0.5-1.0 mm,and d=1.0-2.0 mm were compared.According to EDX mapping,incipient wetness impregnation provides a higher dispersion of the additive and its uniform distribution in the sample.The ignition and combustion characteristics of the modifed anthracite samples were studied by thermal analysis and high-speed video recording of the processes in a combustion chamber(at heating medium temperature of 800℃).It was found that copper acetate increases anthracite reactivity,which was evidenced by decreased onset temperature of combustion(ΔT_(i))by 35-190℃and reduced ignition delay time(Δτ_(i))by 2.1-5.4 s.Copper acetate reduces fuel underburning(on average by 70%)in the ash residue of anthracite and decreases the amount of CO and NO_(x)in gas-phase products(on average by 18.5%and 20.8%,respectively).The mechanism for activation of anthracite combustion by copper acetate is proposed.

Mechanism of mechanical activation for spontaneous combustion of sulfide minerals

In order to uncover the intrinsic reasons for spontaneous combustion of sulfide minerals,representative samples were collected from typical metal mines to carry out the mechanical activation experiment.The structures and heat behaviors of activated samples were characterized by scanning electron microscopy（SEM）,X-ray diffraction（XRD） analysis,and simultaneous thermal analysis（STA）.It is found that the sulfide minerals after mechanical activation show many changes with increased specific surface areas,aggregation phenomenon,decreased diffraction peak intensity,broadened diffraction peak,declined initial temperatures of heat release and self-ignition points.A new theory for explaining the spontaneous combustion of sulfide minerals is put forward：the chemical reaction activity of sulfide minerals is heightened by all kinds of mechanical forces during the mining,and the spontaneous combustion takes place finally under proper environment.

Effect of integration of mechanical ball milling and flue gas desulfurization gypsum on dealkalization of bauxite residue

The synergistic impact of mechanical ball milling and flue gas desulfurization(FGD)gypsum on the dealkalization of bauxite residue was investigated through integrated analyses of solution chemistry,mineralogy,and microtopography.The results showed a significant decrease in Na_(2)O content(>30 wt.%)of FGD gypsum-treated bauxite residue after 30 min of mechanical ball milling.Mechanical ball milling resulted in differentiation of the elemental distribution,modification of the minerals in crystalline structure,and promotion in the dissolution of alkaline minerals,thus enhancing the acid neutralization capacity of bauxite residue.5 wt.%FGD gypsum combined with 30 min mechanical ball milling was optimal for the dealkalization of bauxite residue.

Research Progress in Mechanochemistry of Inorganic Materials

With the progress of science and technology,China has gradually attached importance to research and exploration in chemistry,and the achievements in exploring mechanochemistry are also quite significant.Therefore,it is necessary to study and explore mechanochemistry.This article mainly discusses the application of mechanochemistry in powder and some silicate materials,as well as in special ceramics,and provides a brief introduction to provide reference for relevant researchers.

Microstructures of Sintered Mo-Cu Alloys with Mechanically Activated Powder

Mechanical activation and liquid phase sintering were used to manufacture high performance Mo-Cu alloy and develop new processes. The microstructures and properties of the alloy were investigated. The experimental results showed that: (1) the ball milled Mo/Cu powder has lamellar structure, (2) the microstructures of the sintered Mo-Cu alloy were homogenous compound structures of adhesive phase Cu linking Mo grains, (3) Mo grains frequently strung or gathered in Cu phase, and (4) the full densities of Mo-Cu alloy was achieved through sintering and special densification process. As a result, the properties of the alloy are good enough to satisfy various requirements.

Agglomeration−aggregation and leaching properties of mechanically activated chalcopyrite

The effect of mechanical activation on the granulometric parameters,microstructure,and leaching efficiency of chalcopyrite was evaluated,and the occurrence/transition of agglomeration and aggregation was discussed.The results showed that in 8 h of milling treatment,the agglomeration and the microstructure did not affect each other.However,with prolonging milling time,the crystallite size tended to reach a saturation value,and the stagnating microstructural changes led to the replacement of agglomeration by aggregation.The leaching results indicated that the mechanical activation can strongly enhance the reactivity of chalcopyrite and the hindering effect of aggregation on leaching was considerably greater than that of agglomeration.Consequently,after 8 h of milling,the maximum Cu leaching rate of 80.13%was achieved after 4 h of acid leaching.

Spark plasma sintering on mechanically activated W-Cu powders

Mechanically activated W-Cu powders were sintered by a spark plasma sinteringsystem (SPS) in order to develop a new process and improve the properties of the alloy. Propertiessuch as density and hardness were measured. The microstructures of the sintered W-Cu alloy sampleswere observed by SEM (scanning electron microscope). The results show that spark plasma sinteringcan obviously lower the sintering temperature and increase the density of the alloy. This processcan also improve the hardness of the alloy. SPS is an effective method to obtain W-Cu powders withhigh density and superior physical properties.

Pathogenesis of RON receptor tyrosine kinase in cancer cells: activation mechanism, functional crosstalk, and signaling addiction

The RON receptor tyrosine kinase, a member of the MET proto-oncogene family, is a pathogenic factor im- plicated in tumor malignancy. Specifically, aberrations in RON signaling result in increased cancer cell growth, survival, invasion, angiogenesis, and drug resistance. Biochemical events such as ligand binding, receptor over- expression, generation of structure-defected variants, and point mutations in the kinase domain contribute to RON signaling activation. Recently, functional crosstalk between RON and signaling proteins such as MET and EFGR has emerged as an additional mechanism for RON activation, which is critical for tumorigenic develop- ment. The RON signaling crosstalk acts either as a regulatory feedback loop that strengthens or enhances tumor- igenic phenotype of cancer cells or serves as a signaling compensatory pathway providing a growth/survival ad- vantage for cancer cells to escape targeted therapy. Moreover, viral oncoproteins derived from Friend leukemia or Epstein-Barr viruses interact with RON to drive viral oncogenesis. In cancer cells, RON signaling is integrated into cellular signaling network essential for cancer cell growth and survival. These activities provide the mo- lecular basis of targeting RON for cancer treatment. In this review, we will discuss recent data that uncover the mechanisms of RON activation in cancer cells, review evidence of RON signaling crosstalk relevant to cancer malignancy, and emphasize the significance of the RON signaling addiction by cancer cells for tumor therapy. Understanding aberrant RON signaling will not only provide insight into the mechanisms of tumor pathogenesis, but also lead to the development of novel strategies for molecularly targeted cancer treatment.

Integration of preparation of K,Na-embedded activated carbon and reduction of Zn-bearing dusts

Large amounts of solid wastes and flue gases are generated in iron and steel production process,probably leading to serious environmental pollution without duly handle.An innovative and green process of simultaneous reduction of zinc-bearing dusts and activation of low-rank coal was developed and its mechanism was clarified in this paper.Under the optimal conditions,the reduced zinc-bearing dusts containing low harmful elements(0.02%Zn,0.015%K and 0.03%Na)could be made as high-quality burden for blast furnace while the low-rank coal was transferred into K,Na-embedded activated carbon,which can be used as effective adsorbent for purification of SO_(2) and NO-containing flue gases.The solid wastes were successfully utilized to treat the flue gases through the process.The synergetic activation and reduction mechanism in the process was revealed.The coupling effect between reduction reactions of metal oxides in the dusts and activation reaction of carbon in the coal promoted the simultaneous reduction and activation process.In the meanwhile,part of the potassium and sodium from the zinc-bearing dusts could be adsorbed by the activated carbon and played a catalytic role in the activation process.

Microstructure and Properties of W-Cu Alloys Prepared with Mechanically Activated Powder

W-15% Cu (mass fraction) alloys were sintered with mechanically activated powder in order to develop new preparing processes and improve properties of alloys. The microstructures of the activated powder and the sintered alloy were observed. Properties such as density were measured. The results show that through mechanical activation, the particle size of the powder becomes finer to sub-micron or nanometer level, some copper was soluble in tungsten, and high density W-Cu alloys can be obtained by mechanically activated powder for its action to the activation sintering.

THE MECHANISM FOR NANOMETER-SIZED TiC SYNTHESIZING BY MECHANICAL & THERMAL ACTIVATION PROCESSING

A novel process for synthesizing nano-ceramics powders, named mechanical & therm al activation processing, is discussed in the present paper. It is a processing based on thermal activation in liquid phase (molten salt) after mechanical activ ation. The nanometer-sized TiC particles (15-20nm) have been synthesized by the method, and analyzed by X-ray diffraction (XRD), transmission electron microscop e (TEM), scanning electron microscopy (SEM) and energy dispersion X-ray (EDX) sp ectroscopy. An interface interaction between liquid (molten salt) and solid (fin al product particles) phases plays a dominating role for the control of product particles size. The mechanism for the formation of nanometer-sized TiC particles has been discussed.

Possible Mechanism Associated with Herbicidal Activity of Soybean Meal Hydrolysate (SMH)

Soybean meal hydrolyzate （SMH） has been proposed for use as a natural preemergence herbicide.However,the mechanism by which SMH exerts its herbicidal activity remains unclear.In this paper,the herbicidal activities of SMH against perennial ryegrass （Lolium perenne L.） under non-sterile and sterile conditions were evaluated and the relationship between the molecular weight of the ultrafiltration （UF） fractions of SMH and their herbicidal activities were investigated.Besides,the ammonia content changes of the media of SMH treatments 7 d after incubation were also analyzed.The results showed that SMH inhibited the radicle growth of germinating L.perenne seeds in a dose-dependent manner under non-sterile condition.However,SMH in the concentrations investigated increased the radicle length and shoot length by 14-17% and 11-15% respectively under sterile condition.The ammonia contents in the SMH media at all treatments increased greatly from less than 0.01 mg L-1 to up to 11.86-41.37 mg L-1 after 7 d incubation under non-sterile condition.However,ammonia content did not change under sterile condition,proposing that the herbicidal activity might be caused by the free ammonia released from SMH by microbial activity.There was no difference on the perennial ryegrass radicle inhibition among the UF fractions of SMH on an equivalent N basis.It could be concluded that SMH exerted its herbicidal activity through the free ammonia released under non-sterile condition instead of by specific peptide（s） in SMH.

Arrhenius parameters determination in non-isothermal conditions for mechanically activated Ag_2O-graphite mixture

The non-isothermal kinetics of mechanochemical reduction of Ag2O with graphite was studied by DSC and TGA with a model of fitting Malek approach and a model-free advanced isoconversional method of Vyazovkin. To evaluate the kinetics parameters, Ag2O–graphite mixture of as-received and milled for 2 and 4 h samples were selected. Based on the results obtained by Vyazovkin method calculation, however, the difference between the maximum and minimum values of activation energy is less than 20%-30%of the average activation energy （（99.38±2.36） kJ/mol） and thermal decomposition of mechanically activated Ag2O for 2 h is a multi-step process. Moreover, the thermal decomposition of mechanically activated Ag2O–graphite powder activated for 4 h is a single-step process （the average activation energy=（93.68±2.26） kJ/mol）. The kinetics modeling shows that the complexity of thermal decomposition of as-received Ag2O–graphite mixture is higher than that of the others. While, the autocatalytic tendency of as-received Ag2O–graphite mixture is lower than that of the others.

Microstructures of mechanically activated Ti-46at.%Al powders and spark plasma sintered ultrafine TiAl alloy

Powder of Ti-46at.%Al was synthesized through mechanical activation （MA） for different milling times, and the 16 h MAed powder was sintered by using a spark plasma sintering （SPS） process at different sintering temperatures. The XRD profiles showed that the MAed Ti-46at,%Al powder for 12, 16, and 20 h contained initial α-Ti and Al phases, and that the SPSed TiAl alloys contained the gamma TiAl and α2-Ti3Al phases. The TEM showed two different types of regions in the 16 h MAed Ti-46at.%Al powder. One type consisted of only Al with a grain size about 80 nm, and the other type a mixture of Al and Ti with a grain size of 30 nm. According to the optical micrographs of MA-SPSed samples, the alloys sintered at higher temperatures showed a coarser microstructure. In the case of the 1473 Ksintering, typical duplex structures （（α2 ＋γ） lamella and γ phases） with interlamellar spacings of 50-400 nm and the grain size either less than 100 nm, or 1000 nm were observed.

Microstructure and Mechanical Performance of Cu-SnO_2-rGO based Composites Prepared by Plasma Activated Sintering

A novel chemical technique combined with unique plasma activated sintering（PAS） was utilized to prepare consolidated copper matrix composites（CMCs） by adding Cu-SnO2-rGO layered micro powders as reinforced fillers into Cu matrix. The repeating Cu-SnO2-rGO structure was composed of inner dispersed reduced graphene oxide（r GO）, SnO2 as intermedia and outer Cu coating. SnO2 was introduced to the surface of rGO sheets in order to prevent the graphene aggregation with SnO2 serving as spacer and to provide enough active sites for subsequent Cu deposition. This process can guarantee rGO sheets to suffi ciently disperse and Cu nanoparticles to tightly and uniformly anchor on each layer of rGO by means of the SnO2 active sites as well as strictly control the reduction speed of Cu^2＋. The complete cover of Cu nanoparticles on rGO sheets thoroughly avoids direct contact among rGO layers. Hence, the repeating structure can simultaneously solve the wettability problem between rGO and Cu matrix as well as improve the bonding strength between rGO and Cu matrix at the well-bonded Cu-SnO2-rGO interface. The isolated rGO can effectively hinder the glide of dislocation at Cu-rGO interface and support the applied loads. Finally, the compressive strength of CMCs was enhanced when the strengthening effi ciency reached up to 41.

Activated flux tungsten inert gas welding of 8 mm-thick AISI 304 austenitic stainless steel

AISI 304 stainless steel plates were welded with activated flux tungsten inert gas(A-TIG) method by utilizing self-developed activated flux. It is indicated from the experimental results that for 8 mm-thick AISI 304 stainless steel plate, weld joint of full penetration and one-side welding with good weld appearance can be obtained in a single pass without groove preparation by utilizing A-TIG welding. Moreover, activated flux powders do not cause significant effect on the microstructure of TIG weld and the mechanical properties of A-TIG weld joints are also superior to those of C-TIG(conventional TIG) welding.

THE MECHANISM OF ANTITUMOR ACTIVITY OF TOTAL GLUCOSIDES EXTRACTED FROM CYNANCHUM AURICULA-TUM ROYLE (CA)

Since the chemical structure of total glucosides from Cynanchum Auriculatum Royle (CA) is similar to that of the steroline of Marsdenia Condurago Reich, a compound which exhibits antitumor activity, research into the antitumor activity of CA was carried out. Its mechanism of action was studied in vivo with C 57BL/6 mice bearing Lewis lung carcinoma and in vitro, with two mouse tumor cell lines: S180 and EAC. CA inhibited to a certain extent the growth of subcutaneously inoculated Lewis lung carcinoma and its pulmonary metastasis, and augmented the antitumor effect of cyclophosphamide. It showed a killing effect on the EAC and S180 tumor cells of mice in vitro as well. It blocked the tumor cells of solid Lewis lung carcinoma from entering into the S stage from G1 and inhibited DNA synthesis of S180 and EAC tumor cells of mice in vitro. It also markedly increased the number of mononuclear Mφ of tumor bearing mice, stimulated the macrophagic activity of their intraperitoneal Mφ, raised the percentage of ANAE(+) lymphocytes in peripheral blood and enhanced the ABC reaction and antibody formation in tumor bearing mice.

Effects of Cobalt on the Sintering Behavior of Mechanically Activated Tungsten Powder

Tungsten alloys were prepared with mechanically activated powder added microelement cobalt in order to improve the process and properties of alloys. Properties of alloys such as density, hardness and bending strength were measured. The results show that through mechanical activation, cobalt can accelerate the sintering process of these alloys By the combination of mechanical activation and adding microelement cobalt, tungsten alloys with higher density and better properties can be obtained.

Isothermal thermo-analytical study and decomposition kinetics of non-activated and mechanically activated indium tin oxide(ITO) scrap powders treated by alkaline solution

Isothermal decomposition process of chemically transforming indium tin oxide（ITO） powders into indium（III） hydroxide powders was investigated. Two types of powders were analyzed, i.e., non-activated and mechanically activated. It has been found that in the case of activated sample, shorter induction periods appear, which permits growth of smaller crystals, while in the case of non-activated sample, long induction periods appear, characterized by the growth of larger crystals. DAEM approach has shown that decomposition processes of non-activated and mechanically activated samples can be described by contracting volume model with a linear combination of two different density distribution functions of apparent activation energies（Ea）, and with first-order model, with a single symmetrical density distribution function of Ea, respectively. It was established that specific characteristics of particles not only affect the mechanism of decomposition processes, but also have the significant impact on thermodynamic properties.