UV-Based Advanced Oxidation Processes for Antibiotic Resistance Control: Efficiency, Influencing Factors, and Energy Consumption

Antibiotic resistant bacteria(ARB)with antibiotic resistance genes(ARGs)can reduce or eliminate the effectiveness of antibiotics and thus threaten human health.The United Nations Environment Programme considers antibiotic resistance the first of six emerging issues of concern.Advanced oxidation processes(AOPs)that combine ultraviolet(UV)irradiation and chemical oxidation(primarily chlorine,hydrogen peroxide,and persulfate)have attracted increasing interest as advanced water and wastewater treatment technologies.These integrated technologies have been reported to significantly elevate the efficiencies of ARB inactivation and ARG degradation compared with direct UV irradiation or chemical oxidation alone due to the generation of multiple reactive species.In this study,the performance and underlying mechanisms of UV/chlorine,UV/hydrogen peroxide,and UV/persulfate processes for controlling ARB and ARGs were reviewed based on recent studies.Factors affecting the process-specific efficiency in controlling ARB and ARGs were discussed,including biotic factors,oxidant dose,UV fluence,pH,and water matrix properties.In addition,the cost-effectiveness of the UV-based AOPs was evaluated using the concept of electrical energy per order.The UV/chlorine process exhibited a higher efficiency with lower energy consumption than other UV-based AOPs in the wastewater matrix,indicating its potential for ARB inactivation and ARG degradation in wastewater treatment.Further studies are required to address the trade-off between toxic byproduct formation and the energy efficiency of the UV/chlorine process in real wastewater to facilitate its optimization and application in the control of ARB and ARGs.

Mass Transfer-Promoted Fe^(2+)/Fe^(3+)Circulation Steered by 3D Flow-Through Co-Catalyst System Toward Sustainable Advanced Oxidation Processes

Realizing fast and continuous generation of reactive oxygen species(ROSs)via iron-based advanced oxidation processes(AOPs)is significant in the environmental and biological fields.However,current AOPs assisted by co-catalysts still suffer from the poor mass/electron transfer and non-durable promotion effect,giving rise to the sluggish Fe^(2+)/Fe^(3+)cycle and low dynamic concentration of Fe^(2+)for ROS production.Herein,we present a three-dimensional(3D)macroscale co-catalyst functionalized with molybdenum disulfide(MoS_(2))to achieve ultra-efficient Fe^(2+)regeneration(equilibrium Fe^(2+)ratio of 82.4%)and remarkable stability(more than 20 cycles)via a circulating flow-through process.Unlike the conventional batch-type reactor,experiments and computational fluid dynamics simulations demonstrate that the optimal utilization of the 3D active area under the flow-through mode,initiated by the convectionenhanced mass/charge transfer for Fe^(2+)reduction and then strengthened by MoS_(2)-induced flow rotation for sufficient reactant mixing,is crucial for oxidant activation and subsequent ROS generation.Strikingly,the flow-through co-catalytic system with superwetting capabilities can even tackle the intricate oily wastewater stabilized by different surfactants without the loss of pollutant degradation efficiency.Our findings highlight an innovative co-catalyst system design to expand the applicability of AOPs based technology,especially in large-scale complex wastewater treatment.

Application of advanced oxidation processes for removing salicylic acid from synthetic wastewaters

In this study,advanced oxidation processes(AOPs) such as anodic oxidation(AO),UV/H_2O_2 and Fenton processes(FP) were investigated for the degradation of salicylic acid(SA) in lab-scale experiments.Boron-doped diamond(BDD) film electrodes using Ta as substrates were employed for AO of SA.In the case of FP and UV/H_2O_2,most favorable experimental conditions were determined for each process and these were used for comparing with AO process.The study showed that the FP was the most effective process under aci...

Chemical oxygen demand reduction in coffee wastewater through chemical flocculation and advanced oxidation processes

The removal of the natural organic matter present in coffee processing wastewater through chemical coagulation-flocculation and advanced oxidation processes （AOP） had been studied. The effectiveness of the removal of natural organic matter using commercial flocculants and UV/H202, UV/O3 and UV/H2O2/O3 processes was determined under acidic conditions. For each of these processes, different operational conditions were explored to optimize the treatment efficiency of the coffee wastewater. Coffee wastewater is characterized by a high chemical oxygen demand （COD） and low total suspended solids. The outcomes of coffee wastewater treatment using coagulation-flocculation and photodegradation processes were assessed in terms of reduction of COD, color, and turbidity. It was found that a reduction in COD of 67% could be realized when the coffee wastewater was treated by chemical coagulation-flocculation with lime and coagulant T-1. When coffee wastewater was treated by coagulation-flocculation in combination with UV/H2O2, a COD reduction of 86% was achieved, although only after prolonged UV irradiation. Of the three advanced oxidation processes considered, UV/H2O2, UV/O3 and UV/H2O2/O3, we found that the treatment with UV/H2O2/O3 was the most effective, with an efficiency of color, turbidity and further COD removal of 87%, when applied to the flocculated coffee wastewater.

Degradation of Organic Pollutants by the Advanced Oxidation Processes

A kinetic model has been developed for the degradation of organic pollutants concerning with hydroperoxide ion as the initial step for generation of hydroxyl radical and its subsequent reaction mechanisms. Rate equations were derived for depletion of ozone and pollutants in the peroxone oxidation process using ozone and hydrogen peroxide as combined oxidants. Kinetic data obtained experimentally from the hydrogen peroxide-ozone reaction and peroxone oxidation of nitrobenzene were analyzed by using the proposed rate equations.

Advanced oxidation processes of decomposing dichloroacetic acid and trichloroacetic acid in water

We studied the decomposition of two haloacetic acids (HAAs),dichloroacetic acid (DCAA) and trichloroacetic acid (TCAA),in water by single oxidants ozone (O3) and ultraviolet radiation (UV) and the advanced oxidation processes (AOPs) constituted by the combinations of O3/UV,H2O2/UV,O3 /H2O2,and O3/H2O2/UV. The concentrations of HAAs were analyzed at specified time intervals to track their decomposition. Except for O3 and UV,the four combined oxidation processes remarkably enhance the decomposition of DCAA and TCAA owing to the generated very reactive hydroxyl radicals. The fastest decomposition process is O3/H2O2/UV,closely followed by O3/UV. DCAA is much easier to decompose than TCAA. The kinetics of HAA decomposition by O3/UV can be described well by a pseudo first-order reaction model under a constant initial dissolved O3 concentration and fixed UV radiation. Humic acids and HCO3-in the reaction system both decrease the decomposition rate constants for DCAA and TCAA. The amount of H2O2 accumulates in the presence of humic acids in the O3/UV process.

Effects of Advanced Oxidation Processes on the Decomposition Properties of Organic Compounds with Different Molecular Structures in Water

Studies to decompose persistent organic pollutants in wastewater from chemical factories by using Advanced Oxidation Processes (AOPs) have recently been performed. Oxidation reactions involving ozone and •OH radicals and cleavage caused by UV are the main decomposition reactions that occur in AOPs using ozone and UV. The mechanisms through which organic compounds are decomposed in AOPs are complicated and difficult to understand because various decomposition reactions occur simultaneously. The Total Organic Carbon (TOC) removal efficiencies achieved in several different AOPs were evaluated in this study. The TOC removal efficiencies were different for organic compounds with different chemical structures. The TOC was more effectively removed when aromatic compounds were treated using the O3-UV-TiO2 process than when using the other AOPs, and the TOC was removed more effectively by the O3-UV process than by the UV-TiO2 process. However, the TOC was removed more effectively when open-chain compounds were treated using the UV-TiO2 process than using the O3-UV process, and the UV-TiO2 and O3-UV-TiO2 processes resulted in similar TOC removal efficiencies. Therefore, it is necessary to use the O3-UV-TiO2 process to decompose aromatic compounds as quickly as possible. On the other hand, the UV-TiO2 process degraded the open-chain compounds most effectively, and the O3-UV-TiO2 process did not need to decompose open-chain compounds. Moreover, the TOC of aromatic compounds was removed more slowly than that of open-chain compounds. The TOC removal efficiency increased with decreasing the number of carbon atoms in the molecule. The TOC removal efficiencies increased in order of the organic compounds containing methyl groups, aldehyde groups and carboxyl groups. The removal of the TOC when organic compounds were treated using the O3-UV-TiO2 process followed pseudo-zero-order kinetics.

Review of advanced oxidation processes for treating hospital sewage to achieve decontamination and disinfection

Hospital sewage contains various harmful pharmaceutical contaminants(e.g.,antibiotics,anti-inflammatory agents,and painkillers)and pathogens(e.g.,bacteria,viruses,and parasites),whose direct discharge into the environment will induce diseases and pose a powerful threat to human health and safety,and environmental ecology.In recent years,advanced oxidation processes(AOPs),particularly photocatalysis,electrocatalysis,and ozone catalysis have been developed as widespread and effective techniques for hospital sewage treatments.However,there is a lack of systematic comparison and review of the prior studies on hospital sewage treatment using AOPs systems.This review elaborates on the mechanisms,removal efficiencies,and advantages/disadvantages of these AOPs systems for hospital wastewater decontamination and disinfection.Meanwhile,some novel and potential technologies such as photo-electrocatalysis,electro-peroxone,Fenton/Fenton-like,and piezoelectric catalysis are also included and summarized.Moreover,we further summarize and compare the capacity of these AOPs to treat the actual hospital wastewater under the impact of the water matrix and pH,and estimate the economic cost of these technologies for practical application.Finally,the future development directions of AOPs for hospital wastewater decontamination and disinfection have been prospected.Overall,this study provides a comparison and overview of these AOP systems in an attempt to raise extensive concerns about hospital wastewater decontamination and disinfection technologies and guide researchers to discover the future directions of technologies optimization,which would be a crucial step forward in the field of hospital sewage treatment.

Manganese oxide and derivative-modified materials in advanced oxidation processes:A review of modification enhancement and activation mechanisms

Manganese oxides(MNO_(x)),as low-toxicity and high-abundance catalysts,have been demonstrated to hold great promise for application in advanced oxidation processes(AOPs).However,further application of this material is restricted due to its unsatisfactory oxidant activation efficiency.Fortunately,recently remarkable research on deep activation mechanisms and modification of MNO_(x)have been undertaken to improve its reactivity.Herein,modification enhancement mechanisms of MNO_(x)to efficiently degrade various organic contaminants were discussed and highlighted,including metal doping,coupling with other metal oxides,composite with carbonaceous material,and compounding with other support.The activation mechanisms of different MNO_(x)and derivative-modified material(such as doped MNO_(x),metal oxide-MNO_(x)hybrids,and MNO_(x)-carbonaceous material hybrids)were summarized in great details,which was specifically categorized into both radical and non-radical pathways.The effects of pH,inorganic ions,and natural organic matter on degradation reactions are also discussed.Finally,future research directions and perspectives are presented to provide a clear interpretation on the MNO_(x)initiated AOPs.

Recent advances on decomplexation mechanisms of heavy metal complexes in persulfate-based advanced oxidation processes

In some industrial wastewater,heavy metals combine with organic complexing agents to form heavy metal complexes(HMCs).These HMCs can be difficult to decompose and remove through conventional techniques due to their higher stability than free heavy metal ions.In recent years,persulfate based advanced oxidation processes(PS-based AOPs)have been recognized as a viable technique for HMCs degradation.Nevertheless,a comprehensive and in-depth understanding of the relevant HMCs decomplexation mechanisms in PS-based AOPs is still lacking.This review delineates the current progress of HMCs decomplexation in PS-based AOPs.We discuss the distinctions between the two widely used oxidant types in PS-based AOPs techniques.Moreover,we summarize and highlight the decomplexation mechanisms based on electron and energy transfer,and degradation pathways of HMCs.We also emphasize the effects of environmental water constituents,namely p H,inorganic ions,and natural organic matter(NOM),on HMCs decomplexation.Ultimately,we identify the existing challenges and perspectives that will steer the direction of advancing PS-based AOPs to remove HMCs.

O_(3) based advanced oxidation for ibuprofen degradation

The degradation of the anti-inflammatory ibuprofen(IBP)was evaluated by several advanced oxidation processes.IBP was treated by single ozonation and oxidation with hydrogen peroxide(H_(2)O_(2)),as well as a combination of these treatments.In order to improve the efficiency,the presence of catalysts such as original carbon nanotubes,labelled as CNT,and iron oxide supported on carbon nanotubes,named as Fe/CNT sample,was considered.The evolution of IBP degradation,mineralization and toxicity of the solutions was assessed.The formation of intermediates was also monitored.In the non-catalytic processes,IBP was faster removed by single ozonation,whereas no significant total organic carbon(TOC)removal was achieved.Oxidation with H_(2)O_(2) did not present satisfactory results.When ozone and H_(2)O_(2) were combined,a higher mineralization was attained(70%after 180 min of reaction).On the other hand,in the catalytic processes,this combined process allowed the fastest IBP degradation.In terms of mineralization degree,the presence of Fe/CNT increases the removal rate in the first hour of reaction,achieving a TOC removal of 85%.Four compounds were detected as by-products.All treated solutions presented lower toxicity than the initial solution,suggesting that the released intermediates during applied processes are less toxic.

Acid precipitation coupled membrane-dispersion advanced oxidation process(MAOP)to treat crystallization mother liquor of pulp wastewater

Treatment to crystallization mother liquor containing high concentration of organic and inorganic substances is a challenge in zero liquid discharge of industrial wastewater.Acid precipitation coupled membrane-dispersion advanced oxidation process(MAOP)was proposed for organics degradation before salt crystallization by evaporation.With acid-MAOP treatment CODCrin mother liquor of pulping wastewater was eliminated by 55.2%from ultrahigh initial concentration up to 12,500 mg·L^-1.The decolorization rate was 96.5%.Recovered salt was mainly NaCl(83.3 wt%)having whiteness 50 brighter than industrial baysalt of whiteness 45.The oxidation conditions were optimized as CO3=0.11 g·L^-1 and CH2O2=2.0 g·L^-1 with dispersing rate 0.53 ml·min^-1 for 100 min reaction toward acidified liquor of p H=2.Acidification has notably improved evaporation efficiency during crystallization.Addition of H2O2 made through membrane dispersion has eliminated hydroxyl radical"quench effect"and enhanced the degradation capacity,in particular,the breakage of carbon-chloride bonds(of both aliphatic and aromatic).As a result,the proposed coupling method has improved organic pollutant reduction so as the purity of salt from the wastewater mixture which can facilitate water and salt recycling in industry.

Influence of MnO_(x)deposition on TiO_(2)nanotube arrays for electrooxidation

TiO_(2)has demonstrated outstanding performance in electrochemical advanced oxidation processes(EAOPs)due to its structural stability and high oxygen overpotential.However,there is still much room for improving its electrochemical activity.Herein,narrow bandgap manganese oxide(MnO_(x))was composited with TiO_(2)nanotube arrays(TiO_(2)NTAs)that in-situ oxidized on porous Ti sponge,forming the MnO_(x)-TiO_(2)NTAs anode.XANES and XPS analysis further proved that the composition of MnO_(x)is Mn2O3.Electrochemical characterizations revealed that increasing the composited concentration of MnO_(x)can improve the conductivity and reduce oxygen evolution potential so as to improve the electrochemical activity of the composited MnO_(x)-TiO_(2)NTAs anode.Meanwhile,the optimal degradation rate of benzoic acid(BA)was achieved using MnO_(x)-TiO_(2)NTAs with a MnO_(x)concentration of 0.1 mmol L^(-1),and the role of MnO_(x)was proposed based on DFT calculation.Additionally,the required electrical energy(EE/O)to destroy BA was optimized by varying the composited concentration of MnO_(x)and the degradation voltage.These quantitative results are of great significance for the design and application of high-performance materials for EAOPs.

Fabrication of pollution-free coal gangue-based catalytic material utilizing ferrous chloride as activator for efficient peroxymonosulfate activation

Novel coal gangue-based persulfate catalyst(CG-FeCl_(2))was successfully synthesized by the means of calcinating under nitrogen atmosphere with the addition of ferrous chloride tetrahydrate(FeCl_(2)·_(4)H_(2)O).The phase transformation of the prepared materials and gas products during the heating process are thoroughly investigated.It is suggested that ferrous chloride participated in the phase transformation and formed Si-O-Fe bonds.And the main gaseous products are H_(2)O,H_(2),and HCl during the heating process.Besides,the ability of CG-FeCl_(2) to activate peroxymonosulfate(PMS)for catalytic degradation of polycyclic aromatic hydrocarbons(PAHs)and phenol was deeply studied.More than 95%of naphthyl,phenanthrene and phenol were removed under optimizied conditions.In addition,1O_(2),·OH,and SO_(4)·−were involved in the CG-FeCl_(2)/PMS system from the free radical scavenging experiment,where 1O_(2) played a major role during the oxidation process.Furthermore,CG-FeCl_(2)/PMS system exhibited superior stability in a relatively wide pH range and the presence of common anion from related degradation experiments.Overall,the novel CG-FeCl_(2) is an efficient and environmentally friendly catalyst,displaying potential application prospect in the field of PAHs and phenol-contaminated wastewater treatment.

Recent advances in H_(2)O_(2)-based advanced oxidation processes for removal of antibiotics from wastewater

As important emerging contaminants, antibiotics have caused potential hazards to the ecological environment and human health due to their extensive production and consumption. Among various techniques for removing antibiotics from wastewater, H_(2)O_(2)-based advanced oxidation processes(AOPs) have received increasing attention due to their fast reaction rate and strong oxidation capability. Hence this review critically discusses:(i) Recent research progress of AOPs with the addition of H_(2)O_(2) for antibiotics removal through different methods of H_(2)O_(2) activation;(ii) recent advances in AOPs that can in-situ generate and activate H_(2)O_(2) for antibiotics removal;(iii) H_(2)O_(2)-based AOPs as a combination with other techniques for the degradation and mineralization of antibiotics in wastewater. Future perspectives about H_(2)O_(2)-based AOPs are also presented to grasp the future research trend in the area.

Comparison of UV-based advanced oxidation processes for the removal of different fractions of NOM from drinking water

This study examined the effectiveness for degradation of hydrophobic (HPO),transphilic(TPI) and hydrophilic (HPI) fractions of natural organic matter (NOM) during UV/H_(2)O_(2),UV/TiO_(2)and UV/K2S2O8(UV/PS) advanced oxidation processes (AOPs).The changing characteristics of NOM were evaluated by dissolved organic carbon (DOC),the specific UV absorbance (SUVA),trihalomethanes formation potential (THMFP),organic halogen adsorbable on activated carbon formation potential (AOXFP) and parallel factor analysis of excitation–emission matrices (PARAFAC-EEMs).In the three UV-based AOPs,HPI fraction with low molecular weight and aromaticity was more likely to degradate than HPO and TPI,and the removal efficiency of SUVA for HPO was much higher than TPI and HPI fraction.In terms of the specific THMFP of HPO,TPI and HPI,a reduction was achieved in the UV/H_(2)O_(2)process,and the higest removal rate even reached to 83%.UV/TiO_(2)and UV/PS processes can only decrease the specific THMFP of HPI.The specific AOXFP of HPO,TPI and HPI fractions were all able to be degraded by the three UV-based AOPs,and HPO content is more susceptible to decompose than TPI and HPI content.UV/H_(2)O_(2)was found to be the most effective treatment for the removal of THMFP and AOXFP under given conditions.C1 (microbial or marine derived humic-like substances),C_(2) (terrestrially derived humic-like substances)and C_(3) (tryptophan-like proteins) fluorescent components of HPO fraction were fairly labile across the UV-based AOPs treatment.C_(3) of each fraction of NOM was the most resistant to degrade upon the UV-based AOPs.Results from this study may provide the prediction about the consequence of UV-based AOPs for the degradation of different fractions of NOM with varied characteristics.

Studies on reaction mechanisms and distinct chemiluminescence from cyanoimino neonicotinoids triggered by peroxymonosulfate in advanced oxidation processes

In this study, we proposed a novel method to investigate the advanced oxidation process of neonicotinoids(NNIs) from the perspective of concomitant chemiluminescence(CL) reaction. It was found that in the presence of cobalt ions with cyanoimino NNIs, acetamiprid(ACE) and thiacloprid(THI), could promote peroxymonosulfate and Ru(bpy)_(3)^(2+) to produce strong CL, but no CL occurred with nitro-involved NNIs as alternatives. Experimental dada from UV absorption spectra and chemiluminescence spectra suggested that new cyclic compounds might be formed during the reaction. Based on the results of free radical scavenging experiment and mass spectra, a new degradation and reaction mechanism of cyanoiminocontaining NNIs was proposed. ACE or THI were first attacked by SO_(4)^(·-) to form benzyl radicals, which in turn reacted with the carbon atoms of cyano group through electrophilic addition reaction in the formation of intramolecular ring. Then a redox reaction between Ru(bpy)_(3)^(3+) and imino group immediately took place with CL emission(610 nm). The new mechanistic knowledge would be meaningful for other contaminants for their interactions with PMS.

Roles and mechanisms of carbonaceous materials in advanced oxidation coupling processes for degradation organic pollutants in wastewater:a review

The widespread organic pollutants in wastewater are one of the global environmental problems.Advanced oxidation processes(AOPs)are widely used because of their characteristics of high efficiency and strong oxidation.However,AOPs may have some defects,such as incomplete mineralization of organic pollutants and the generation of toxic by-products during the degradation process,thus it is essential to seek efficient and green wastewater treatment technologies.Coupling different AOPs or other processes is beneficial for the mineralization of pollutants and reduces ecological risks to the environment.It is worth noting that carbonaceous materials(CMs)have received widespread attention and application in the degradation of organic pollutants in water by advanced oxidation coupling processes(C-AOPs)due to their excellent physicochemical properties in recent years.However,the behaviors and mechanisms of C-AOPs based on CMs on the degradation of organic pollutants are still unknown.Therefore,it is essential to comprehensively summarize the recent research progress.In this review,the applications of different CMs in C-AOPs were reviewed first.Secondly,the synergistic mechanisms of the C-AOPs based on different CMs were discussed.Then,toxic intermediates were explored and important toxicity assessment methods were proposed.Finally,the application potential of the C-AOPs in the future and the challenges were proposed.This review provides an important reference for the application and optimization of the C-AOPs in organic wastewater treatment in the future.

Removal of citrate and hypophosphite binary components using Fenton,photo-Fenton and electro-Fenton processes

Both citrate and hypophosphite in aqueous solution were degraded by advanced oxidation processes （Fe^2＋/H2O2, UV/Fe^2＋/H2O2, and electrolysis/Fe^2＋/H2O2） in this study. Comparison of these techniques in oxidation efficiency was undertaken. It was found that Fenton process could not completely degrade citrate in the presence of hypophosphite since it caused a series inhibition. Therefore, UV light （photo-Fenton） or electron current （electro-Fenton） was applied to improve the degradation efficiency of the Fenton process. Results showed that both photo-Fenton and electro-Fenton processes could overcome the inhibition of hypophosphite, especially the electro-Fenton.

Photo oxidation of DBT using carbon nanotube titania composite as visible light active photo catalyst

Sulfur removal from liquid fuels has increased in importance in recent years. Although hydrodesulfurization is the usual method for removing sulfur, the elimination of thiophene compounds using this process is difficult. Photocatalysis is an alternative method being developed for thiophene removal at ambient conditions. Among semiconductors, titania has shown good potential as a photo-catalyst; however, quick recombination of electron holes hinders its commercial use. One way to decrease the recombination rate is to combine carbon nanotubes with a semiconductor. In this work, multiwall carbon nanotube （MWCNT） / titania composites were prepared with different mass ratios of MWCNT to titania using tetraethyl orthotitanate （TEOT） and titanium tetra isopropoxide （TTIP） as precursors of titania. Dibenzothiophene （DBT） photocatalytic removal from n-hexane was measured in both the presence and absence of oxygen. The results indicated that the best removal occurred when the MWCNT to titania ratio was 1. When the ratio exceeded this number, DBT removal efficiency decreased due to light scattering. Also, the composites prepared by TEOT exhibited better efficiency in DBT removal. The research findings suggested that the obtained composite was a visible light active photocatalyst and exhibited better performance in the presence of oxygen. Kinetics of photocatalytic DBT removal was a first-order reaction with removal rate constant 0.7 h–1 obtained at optimum conditions.