UNSTEADY TRANSONIC AERODYNAMIC LOADINGS ON THE AIRFOIL CAUSED BY HEAVING, PITCHING OSCILLATIONS AND CONTROL SURFACE

An implicit upwind finite volume solver for the Euler equations using the improved flux - splitting method is established and used to calculate the transonic flow past the airfoils with heaving, pitching oscillations and the control surface. Results are given for the NACA64A - 10 airfoil which is in harmonic heaving and pitching oscillation and with the control surface in the transonic flow field. Some computational results are compared with the experiment data and the good agreements are shown in the paper.

Research on stability of laminated composite plate under nonlinear aerodynamic load

In this paper,we propose an finite element approach based on classical plate theory to investigate the dynamic stability of a layered composite plate subject to nonlinear aerodynamic load.This study considers the influence of temperature,nonlinear geometry,and nonlinear aerodynamic load on composite plate structures simultaneously.Specifically,the present work conduct comparison the results of the critical pressure value between the nonlinear aerodynamic load and the linear aerodynamic load,thereby pointing out some necessary cases which must consider the nonlinearity of aerodynamic load for calculating the aerospace structures.We determine the critical pressure value and vibrational amplitude response of the plate by means of calculation.The outcomes of our calculations can be useful in designing and repairing body shells and wings of aircraft equipment.

Influences of aerodynamic loads on hunting stability of high-speed railway vehicles and parameter studies

The influences of steady aerodynamic loads on hunting stability of high-speed railway vehicles were investigated in this study.A mechanism is suggested to explain the change of hunting behavior due to actions of aerodynamic loads：the aerodynamic loads can change the position of vehicle system（consequently the contact relations）,the wheel/rail normal contact forces,the gravitational restoring forces/moments and the creep forces/moments.A mathematical model for hunting stability incorporating such influences was developed.A computer program capable of incorporating the effects of aerodynamic loads based on the model was written,and the critical speeds were calculated using this program.The dependences of linear and nonlinear critical speeds on suspension parameters considering aerodynamic loads were analyzed by using the orthogonal test method,the results were also compared with the situations without aerodynamic loads.It is shown that the most dominant factors a ff ecting linear and nonlinear critical speeds are different whether the aerodynamic loads considered or not.The damping of yaw damper is the most dominant influencing factor for linear critical speeds,while the damping of lateral damper is most dominant for nonlinear ones.When the influences of aerodynamic loads are considered,the linear critical speeds decrease with the rise of cross wind velocity,whereas it is not the case for the nonlinear critical speeds.The variation trends of critical speeds with suspension parameters can be significantly changed by aerodynamic loads.Combined actions of aerodynamic loads and suspension parameters also a ff ect the critical speeds.The effects of such joint action are more obvious for nonlinear critical speeds.

Prediction of Aerodynamic Interactions of Helicopter Rotor on its Fuselage

An iterative and full-coupled rotor/fuselage aerodynamic interaction analytical method is developed based upon the rotor free-wake model and the 3-D fuselage panel model. A close vortex/ surface interaction model using the Analytical/Numerical Matching (ANM) was adopted in the method in order to simulate effectively the unsteady close interaction between the rotor tip-vortex and fuselage surface. By the analytical method, the unsteady and steady pressure distribution on the fuselage surface, and the unsteady lift and pitching moment of the fuselage in a rotor interaction environment were calculated for different advance ratios. It is shown that the unsteady aerodynamic loads of the fuselage due to the rotor interaction have the same periodic characteristics as the rotor. The comparisons between the present close vortex/surface interaction model and a previous model, which simply excludes vortex filaments inside the fuselage, were also made and the advantages of the former over the latter were demonstrated in improving unsteady close interaction calculations.

Superposability of unsteady aerodynamic loads on bridge deck sections

The 2-dimensional unsteady aerodynamic forces,in the context of both a thin airfoil where theory of potential flow is always applicable and a bluff bridge-deck section where separated flow is typically induced,are investigated from a point of view of whether or not they conform to the principle of linear superposition in situations of various structural motions and wind gusts.It is shown that some basic preconditions that lead to the linear superposability of the unsteady aerodynamic forces in cases of thin airfoil sections are no longer valid for a bluff section.Theoretical models of bridge aerodynamics such as the one related to flutter-buffeting analysis and those concerning aerodynamic admittance(AA)functions,however,necessitate implicitly this superposability.The contradiction revealed in this work may throw light on the perplexing problem of AA functions pertaining to the description of buffeting loads of bridge decks.Some existing theoretical AA models derived from flutter derivatives according to interrelations valid only for thin airfoil theories,which have been employed rather extensively in bridge aerodynamics,are demonstrated to be illogical.Finally,with full understanding of the preconditions of the applicability of linear superposability of the unsteady aerodynamic forces,suggestions in regard to experiment-based AA functions are presented.

Experimental investigation on tip vortices and aerodynamics of a wing with ground effect

The tip vortices and aerodynamics of a NACA0012 wing in the vicinity of the ground were studied in a wind tunnel.The wing tip vortex structures and lift/drag forces were measured by a seven-hole probe and a force balance,respectively.The evolution of the flow structures and aerodynamics with a ground height were analyzed.The vorticity of tip vortices was found to reduce with the decreasing of the ground height,and the position of vortex-core moved gradually to the outboard of the wing tip.Therefore,the down-wash flow induced by the tip vortices was weakened. However,vortex breakdown occurred as the wing lowered to the ground.From the experimental results of aerodynamics,the maximum lift-to-drag ratio was observed when the angle of attack was 2.5°and the ground clearance was 0.2.

Characteristic Aerodynamic Loads and Load Effects on the Dynamics of a Floating Vertical Axis Wind Turbine

The development of offshore wind farms in deep water favors floating wind turbine designs, but floating horizontal axis wind turbines are facing the challenge of high cost of energy (CoE). The development of innovative designs to reduce the CoE is thus desirable, such as floating vertical axis wind turbines (VAWTs). This study demonstrates the characteristics of aerodynamic loads and load effects of a two-bladed floating VAWT supported by a semi-submersible platform. Fully coupled simulations are performed using the time-domain aero-hydro-servo-elastic code SIMO-RIFLEX-AC. It is found that thrust, lateral force, and aerodynamic torque vary considerably and periodically with the rotor azimuth angle. However, the variation in the generator torque can be alleviated to some extent by the control strategy applied. Moreover, the variations of platform motions and tensions in the mooring lines are strongly influenced by turbulent winds, whereas those of tower-base bending moments are not. The tower-base bending moments exhibit notable two-per-revolution (2P) response characteristics. © 2017 Tianjin University and Springer-Verlag GmbH Germany

EXPERIMENTAL INVESTIGATION OF AERODYNAMICINTERACTION EFFECT OF ROTOR WAKE ONFUSELAGE OF HELICOPTER

The interaction effect of rotor wake on fuselage of helicopter was investigated with experimental method. The results from experiment have proved that for the drag of fuselage the effect of rotor airflow is closely in connection with both the flight speed and the collective pitch of blades, while for the thrust and pitch moment of fuselage the collective pitch angle of blades plays more important role. A simple and effective computing method about aerodynamic interaction can be derived from the measured data. In order to implement the experiment, a fuselage model, a special sensor, the measurement and data acquisition and processing system were designed and manufactured according to the special requirements of this research project, thereby a good base was built up for carrying out experiments successfully with high quality.

APPLICATION OF NONLINEAR PID CONTROLLER IN AERODYNAMICS LOADING SYSTEM

The design idea of tracking-differentiator and the nonlinear PID controllerare introduced, the applicable algorithm and its real result for distributed aerodynamicsloading control system are discussed, and the construction of the test & contro1 system arealso presented. The application shows that the nonlinear PID algorithm has the advan-tages of high reliability, short run time and strong stability.

Inverse aerodynamic design for distributed propulsion wing with expected circulation distribution

Distributed Propulsion Wing(DPW)technology offers significant advantages in terms of flight energy savings,but the strong aerodynamic coupling between the propulsive internal flow and aerodynamic external flow brings significant design challenges.As the primary DPW profile design is of great significance,this paper proposes a hybrid method to solve the inverse problem mainly based on the formula relationship between the required aerodynamic loads and the profile shape,which is more direct and instructive compared with traditional parametric iterative methods.The aerodynamic characteristics are described by the circulation distribution in the Fourier series form,then the mean camber line of the profile is solved through the re-derived airfoil theory considering disk's influence.Further CFD correction methods are also proposed.To validate the effectiveness and feasibility of the proposed hybrid inverse method,several DPW profile design tests are then conducted.Finally,the relationship between 2D and realistic 3D unit shape is also researched.The results show that the proposed inverse design method has great accuracy and convergence speed in the design tests,and shows good robustness against changes of the design parameters.The 2D profile shape and the actual 3D shape of DPW unit can establish an aerodynamic-propulsion equivalent relationship based on the same internal mass fluxes.

Operational Safety Assessment of a High-Speed Train Exposed to the Strong Gust Wind

The operational safety characteristics of trains exposed to a strong wind have caused great concern in recent years.In the present paper,the effect of the strong gust wind on a high-speed train is investigated.A typical gust wind model for any wind angle,named“Chinese hat gust wind model”,was first constructed,and an algorithm for computing the aerodynamic loads was elaborated accordingly.A vehicle system dynamic model was then set up in order to investigate the vehicle system dynamic characteristics.The assessment of the operational safety has been conducted by means of characteristic wind curves(CWC).As some of the parameters of the wind-train system were difficult to measure,we also investigated the impact of the uncertain system parameters on the CWC.Results indicate that,the descending order of the operational safety index of the vehicle for each wind angle is 90°-60°-120°-30°-150°,and the worst condition for the operational safety occurs when the wind angle reaches around 90°.According to our findings,the gust factor and aerodynamic side force coefficient have great impact on the critical wind speed.Thus,these two parameters require special attention when considering the operational safety of a railway vehicle subjected to strong gust wind.

Determination method of load balance ranges for train operation safety under strong wind

The aerodynamic performances of a passenger car and a box car with different heights of windbreak walls under strong wind were studied using the numerical simulations, and the changes of aerodynamic side force, lift force and overturning moment with different wind speeds and wall heights were calculated. According to the principle of static moment balance of vehicles, the overturning coefficients of trains with different wind speeds and wall heights were obtained. Based on the influence of wind speed and wall height on the aerodynamic performance and the overturning stability of trains, a method of determination of the load balance ranges for the train operation safety was proposed, which made the overturning coefficient have nearly closed interval. A min(|A1|+|A2|), s.t. |A1|→|A2|(A1 refers to the downwind overturning coefficient and A2 refers to the upwind overturning coefficient)was found. This minimum value helps to lower the wall height as much as possible, and meanwhile, guarantees the operation safety of various types of trains under strong wind. This method has been used for the construction and improvement of the windbreak walls along the Lanzhou–Xinjiang railway(from Lanzhou to Urumqi, China).

On-line control of surface quality for an axially moving steel strip partially immersed in fluid under tension

An on-line control method of surface quality for continuous hot-dip galvanized steel strip after cooling is presented, which combines analytical dynamics theory of a thin plate with the finite element method. The inherent characteristics of the non-immersed and partially immersed strip in liquid zinc were calculated on the basis of theoretical analysis and numerical simulation, respectively. Multi-parameter fitting of the deviation between results using different methods was performed. To optimize the strip excitation frequency away from the resonance region, on-line vibration control of the strip near the air knife under full product conditions was achieved by changing the field production parameters based on the field test results. The results indicate that although the axial velocity has little effect on the inherent characteristics of the strip compared with other manufacturing parameters such as the steel specifications and tension, it induces external excitations,including moving the aerodynamic load and bearing vibration. To some degree, the vibration near the air knife can be reduced by strengthening the support stiffness of the contact rolls. A total on-line control program of surface quality for continuous hot-dip galvanized pure Zn and galvannealed steel sheet in the cooling section is proposed.

Static and Dynamic Study of a Wind Turbine Blade with Horizontal Axis

In this work the authors present a calculation process of the blades for wind turbine with horizontal axis. It is about a blade discretized by the finite element method （FEM） in order to determine the gyroscopic effect during its rotation at a high speed. A blade must have the maximum output and resist to aerodynamic loads distributed over its length, which are related to its geometrical characteristics and the speed of the wind. For that, the authors wrote the relations whom determine these loads according to the flow speed of the wind, then, the authors integrated them in the laws of structure mechanics to obtain the motion equations of the blade. This process was applied to a twisted blade with a length of 1.9 m, built out of pressed aluminum sheet with a profile of the type NACA; this profile gives the best aerodynamic output. This blade is an element of a three-bladed propeller for wind turbine of maximum power 5 kW. Finally, we visualized its deformations and then the authors checked its holding in service.

Airfoil Roof in Buildings

In this paper an airfoil that is used on roofs was analyzed:Circular Arc Airfoil.The JavaFoil program for the calculation of aerodynamic parameters of the simulated wing airfoil and small AR(aspect ratio)was used.A wing roof scale model was constructed,and it was tested in the wind tunnel of the Laboratory of Environmental Fluid Dynamics,Universidad Nacional del Comahue.In the model,the AR was equal to 1.46.Thickness of the model was 32%.The tests were conducted at a Reynolds number of 1×10^(5).The curves of the lift coefficient versus angle of attack were obtained,and the pressure coefficient Cp was determined for each surface.The lift coefficients and the Cp values differ from the theoretical profile;this shows the importance of using the wind tunnel to obtain experimental data to achieve a good structural design.

Aerodynamic and structural characteristics of helicopter rotor in circling flight

To investigate the distinct properties of the helicopter rotors during circling flight,the aerodynamic and dynamic models for the main rotor are established considering the trim conditions and the flight parameters of helicopters.The free wake method is introduced to compute the unsteady aerodynamic loads of the rotor characterized by distortions of rotor wakes,and the modal superposition method is used to predict the overall structural loads of the rotor.The effectiveness of the aerodynamic and the structural methods is verified by comparison with the experimental results,whereby the influences of circling direction,radius,and velocity are evaluated in both aerodynamic and dynamic aspects.The results demonstrate that the circling condition makes a great difference to the performance of rotor vortex,as well as the unsteady aerodynamic loads.With the decrease of the circling radius or the increment of the circling velocity,the thrust of the main rotor increases apparently to balance the inertial force.Meanwhile,the harmonics of aerodynamic loads in rotor disc change severely and an evident aerodynamic load shock appears at high-order components,which further causes a shift-of-peak-phase bending moment in the flap dimension.Moreover,the advancing side of blade experiences second blade/vortex interaction,whose intensity has a distinct enhancement as the circling radius decreases with the motion of vortexes.

Non-synchronous vibration of rotor blade in a six-stage transonic compressor

This paper presents an experimental study on the Non-Synchronous Vibration(NSV)in a six-stage transonic compressor.The first part of the paper describes the NSV phenomenon of Rotor 1,which occurs when both Stator 1(S1)and Stator 2(S2)or S1 only are closed.Detailed measurements and analysis are carried out for the former case through the unsteady wall pressure and the Blade Strain(BS).The spinning mode theory used in the rotor/stator interaction noise is employed to explain the relation between the circumferential wave number of the aerodynamic disturbance and the Nodal Diameter(ND)of the blade vibration.The variations of the vibration amplitudes of different blades and the Inter-Blade Phase Angles(IBPAs)at different moments suggest that the evolution of NSV is a highly nonuniform phenomenon along the circumferential direction.In addition,the difference between the wall-pressure spectra generated by the NSV and the classic flutter has been discussed.In the second part,the variations of aerodynamic loading due to the adjustment of the staggers of the Inlet Guide Vane(IGV),S1 and S2 have been investigated.It is found that closing S1 only can result in a great fluctuation to the performance of the front stages,which might be detrimental to the flow organization and increase the risk of NSV.In contrast,the effect of closing S2 only on the performance of the first two stages appears to be slighter relatively.

Model Aerodynamic Tests with a Wire-driven Parallel Suspension System in Low-speed Wind Tunnel

Owing to the advantages of wire-driven parallel manipulator, a new wire-driven parallel suspension system for airplane model in low-speed wind tunnel is constructed, and the methods to measure and calculate the aerodynamic parameters of the airplane model are studied. In detail, a static model of the wire-driven parallel suspension is analyzed, a mathematical model for describ- ing the aerodynamic loads exerted on the scale model is constructed and a calculation method for obtaining the aerodynamic parameters of the model by measuring the tension of wires is presented. Moreover, the measurement system for wire tension and its corresponding data acquisition system are designed and built. Thereafter, the wire-driven parallel suspension system is placed in an open return circuit low-speed wind tunnel for wind tunnel tests to acquire data of each wire tension when the airplane model is at different attitudes and different wind speeds. A group of curves about the parameters for aerodynamic load exerted on the airplane model are obtained at different wind speeds after the acquired data are analyzed. The research results validate the feasibility of using a wire-driven parallel manipulator as the suspension system for low-speed wind ttmnel tests.

Aerodynamic design of tractor propeller for high-performance distributed electric propulsion aircraft

Aiming to maximize the aerodynamic performance of the Distributed Electric Propulsion(DEP)aircraft,a hybrid design framework which focuses on the aerodynamic performance of the propeller/wing integration has been developed and validated numerically.Variable-fidelity modelling for propeller aerodynamics has been used to achieve computational efficiency with reasonable accuracy.By optimizing the aerodynamic loading distributions on the tractor propeller disk,the induced slipstream is redistributed into a form that is beneficial for the wing downstream,based on which the propeller blade geometry is generated through a rapid inversed design procedure.As compared with the Minimum Induced Loss(MIL)propeller at a specified thrust level,significant improvements of both the lift-to-drag ratio of the wing and the propeller/wing integrated aerodynamic efficiency is achieved,which shows great promise to deliver aerodynamic benefits for the wing within the propeller slipstream without any additional devices.

Numerical simulation of the aerodynamic characteristics of heavy-duty trucks through viaduct in crosswind

In our numerical simulation the hybrid mesh and the SST k-ω turbulence model are adopted to investigate the variations of the aerodynamic loads and the flow field of heavy-duty trucks while crossing a viaduct with 1.1 m high fences in a crosswind at a velocity of 20 m/s. The results show that, with the protection of a fence, the side force is weakened, and the rolling and yaw moments are strengthened while the truck is crossing the viaduct, which relatively reduces the roll-over safety and the driving stability of the truck. Meanwhile, the direction of the side force changes when the truck enters the viaduct, which makes the roll-over safety and the driving stability the lowest during the process.