Airfoil friction drag reduction based on grid-type and super-dense array plasma actuators

To improve the cruise flight performance of aircraft, two new configurations of plasma actuators(grid-type and super-dense array) were investigated to reduce the turbulent skin friction drag of a low-speed airfoil. The induced jet characteristics of the two actuators in quiescent air were diagnosed with high-speed particle image velocimetry(PIV), and their drag reduction efficiencies were examined under different operating conditions in a wind tunnel. The results showed that the grid-type plasma actuator was capable of producing a wall-normal jet array(peak magnitude: 1.07 m/s) similar to that generated in a micro-blowing technique, while the superdense array plasma actuator created a wavy wall-parallel jet(magnitude: 0.94 m/s) due to the discrete spanwise electrostatic forces. Under a comparable electrical power consumption level,the super-dense array plasma actuator array significantly outperformed the grid-type configuration,reducing the total airfoil friction drag by approximately 22% at a free-stream velocity of 20 m/s.The magnitude of drag reduction was proportional to the dimensionless jet velocity ratio(r), and a threshold r = 0.014 existed under which little impact on airfoil drag could be discerned.

Cerium-tungsten oxides supported on activated red mud for the selective catalytic reduction of NO_(x)

Activated red mud(RM)has been proved to be a promising base material for the selective catalysis reduction(SCR)of NOx.The inherent low reducibility and acidity limited its low-temperature activity.In this work,molybdenum oxide,tungsten oxide,and cerium oxide were used to reconfigure the redox sites and acid sites of red mud based catalyst.When activated red mud was reconfigured by cerium-tungsten oxide(Ce-W@RM),the NOx conversion kept above 90%at 219-480℃.The existence of Ce^(3+)/Ce^(4+) redox electron pairs provided more surface adsorbed oxygen(O_(α)) and served as a redox cycle.Positive interactions between Ce,W species and Fe oxide in red mud occurred,which led to the formation of unsaturated chemical bond and promoted the activation of adsorbed NH_(3) species.WO_(3) and Ce_(2)(WO_(4))_(3)(formed by solid-state reaction between Ce and W species)could provide more Brønsted acid sites(W-O modes of WO_(3),W=O or W-O-W modes of Ce_(2)(WO_(4))_(3)).CeO_(2) species could provide more Lewis acid sites.The Langmuir-Hinshelwood(L-H)routes and Eley-Rideal(E-R)routes occurred in the low-temperature SCR reaction on the Ce-W@RM surface.NH_(4)^(+) species on Brønsted acid sites,NH_(3) species on Lewis acid sites,bidentate nitrate and bridging nitrate species were key active intermediates species.

A new reduction-based LQ control for dynamic systems with a slowly time-varying delay

Time delays in the feedback control often dete- riorate the control performance or even cause the instability of a dynamic system. This paper presents a control strategy for the dynamic system with a constant or a slowly time-varying input delay based on a transformation, which sire-plifies the time-delay system the relation is discussed for into a delay-free one. Firstly, two existing reduction-based linear quadratic controls. One is continuous and the other is discrete. By extending the relation, a new reduction-based control is then developed with a numerical algorithm presented for practical control implementation. The controller suggested by the proposed method has such a promising property that it can be used for the cases of different values of an input time delay without redesign of controller. This property provides the potential for stabilizing the dynamic system with a time-varying input delay. Consequently, the application of the proposed method to the dynamic system with a slowly time-varying delay is discussed. Finally, numerical simulations are given to show the efficacy and the applicability of the method.

Active control of turbulence for drag reduction based on the detection of near-wall streamwise vortices by wall information

The spatial relations between the measurable wall quantities （streamwise shear stress τwx, spanwise shear stress τwz, and pressure fluctuations Pw） and the near-wall streamwise vortices （NWSV） are investigated via direct numerical simulation （DNS） databases of fully developed turbulent channel flow at a low Reynolds number. In the stan- dard turbulent channel flow, the results show that all the wall measurable variables are closely associated with the NWSV. But after applying a stochastic interference, the relation based on τwx breaks down while the correlations based on Pw and τwz are still robust. Hence, two wall flow quantities based on Pw and τwz are proposed to detect the NWSV. As an appli- cation, two new control schemes are developed to suppress the near-wall vortical structures using the actuation of wall blowing/suction and obtain 16 % and 11% drag reduction, respectively.

Model-based Predictive Control for Spatially-distributed Systems Using Dimensional Reduction Models

In this paper, a low-dimensional multiple-input and multiple-output （MIMO） model predictive control （MPC） configuration is presented for partial differential equation （PDE） unknown spatially-distributed systems （SDSs）. First, the dimension reduction with principal component analysis （PCA） is used to transform the high-dimensional spatio-temporal data into a low-dimensional time domain. The MPC strategy is proposed based on the online correction low-dimensional models, where the state of the system at a previous time is used to correct the output of low-dimensional models. Sufficient conditions for closed-loop stability are presented and proven. Simulations demonstrate the accuracy and efficiency of the proposed methodologies.

Investigations of the effects of two typical jet crushing methods on the atomization and dust reduction performance of nozzles

Single-fuid nozzles and dual-fuid nozzles are the two typical jet crushing methods used in spray dust reduction. To distinguish the atomization mechanism of single-fuid and dual-fuid nozzles and improve dust control efciency at the coal mining faces, the atomization characteristics and dust reduction performance of the two nozzles were quantitatively compared. Results of experiments show that, as water supply pressure increased, the atomization angle of the swirl pressure nozzle reaches a maximum of 62° at 6 MPa and then decreases, but its droplet size shows an opposite trend with a minimum of 41.7 μm. The water supply pressure helps to improve the droplet size and the atomization angle of the internal mixing air–liquid nozzle, while the air supply pressure has a suppressive efect for them. When the water supply pressure is 0.2 MPa and the air supply pressure reaches 0.4 MPa, the nozzle obtains the smallest droplet size which is 10% smaller than the swirl pressure nozzle. Combined with the dust reduction experimental results, when the water consumption at the working surface is not limited, using the swirl pressure nozzle will achieve a better dust reduction efect. However, the internal mixing air–liquid nozzle can achieve better and more economical dust reduction performance in working environments where water consumption is limited.

Controllable synthesis of Fe–N4 species for acidic oxygen reduction

Controllable design and synthesis of catalysts with the target active sites are extremely important for their applications such as for the oxygen reduction reaction(ORR)in fuel cells.However,the controllably synthesizing electrocatalysts with a single type of active site still remains a grand challenge.In this study,we developed a facile and scalable method for fabricating highly efficient ORR electrocatalysts with sole atomic Fe-N4 species as the active site.Herein,the use of cost-effective highly porous carbon as the support not only could avoid the aggregation of the atomic Fe species but also a feasible approach to reduce the catalyst cost.The obtained atomic Fe-N4 in activated carbon(aFe@AC)shows excellent ORR activity.Its half-wave potential is 59 mV more negative but 47 mV more positive than that of the commercial Pt/C in acidic and alkaline electrolytes,respectively.The full cell performance test results show that the aFe@AC sample is a promising candidate for direct methanol fuel cells.This study provides a general method to prepare catalysts with a certain type of active site and definite numbers.

Improved MPPT Control Based on the Reduction of Tracking Range

考虑到基于转矩调整的改进方法存在难以获取最优调整状态的问题，该文针对传统功率曲线法提出收缩风机转速的跟踪区间、减小跟踪路程的改进思路，以优化风机最大功率点跟踪的性能。在此基础上，设计出根据平均风速，周期性的调整起始发电转速的改进功率曲线法。其设计机理在于风速平均值恰好反映了风速及风能量集中分布的区间。因此，最优转速跟踪区间与平均风速存在数量上的直接关系而变得容易预估，且无需迭代搜索。与目前基于调整转矩的改进方法相比，该文所提方法不仅提高了风能捕获效率，且简单易行。最后，通过对模拟风速序列的仿真计算与比较分析，验证了该方法的有效性和先进性。

Synthesis of super high molecular weight copolymer of AM/NaA/AMPS by oxidation–reduction and controlled radical polymerization

Super high molecular weight copolymers of AM/NaA/AMPS were prepared by oxidation–reduction[OR-P(AM/NaA/AMPS)]and controlled radical polymerization[CR-P(AM/NaA/AMPS)].The resulting copolymers were fully characterized,and the reaction conditions for their preparation were optimized.OR-P(AM/NaA/AMPS),CR-P(AM/NaA/AMPS),and conventional partially hydrolyzed polyacrylamide(HPAM)in brine solution were comprehensively characterized by thermogravimetric analysis,scanning electron microscopy,atomic force microscopy,and dynamic light scattering.ORP(AM/NaA/AMPS)and CR-P(AM/NaA/AMPS)containing AMPS monomer showed better salt resistance,temperature tolerance,and viscosification property than the conventional HPAM polymer,making them more promising for enhanced oil recovery.Through comprehensive comparison and analysis,it was found that OR-P(AM/NaA/AMPS)was more conducive for high-temperature condition due to the existence of xanthone in OR-P(AM/NaA/AMPS).On the other hand,CR-P(AM/NaA/AMPS)was more suitable for high-mineral atmosphere,which could be attributed to its higher intrinsic viscosity.

Model reduction and active control of flexible beam using internal balance technique

The internal balance technique is effective for the model reduction in flexible structures, especially the ones with dense frequencies. However, due to the difficulty in extracting the internal balance modal coordinates from the physical sensor readings, research on this topic has been mostly theoretical so far, and little has been done in experiments or engineering applications. This paper studies the internal balance method theoretically as well as experimentally and designs an active controller based on the reduction model. The research works on a digital signal processor （DSP） TMS320F2812- based experiment system with a flexible beam and proposes an approximate approach to access the internal balance modal coordinates. The simulation and test results have shown that the proposed approach is feasible and effective, and the designed controller is successful in restraining the beam vibration.

Model control technologies of dynamic secondary cooling and soft reduction for slab continuous casting

Dynamic model control technologies of secondary cooling and soft reduction of Baosteel are introduced. Model principle and control system architecture are summarized, as well as functions and features. Finally, applications of model technologies are discussed. The self-developed dynamic secondary cooling model and the dynamic soft reduction model have been applied on several casting machines inside and outside Baosteel, desired control effects were achieved with good stability and reliability. Temperature measurement results verified the correctness of model.

Model Reduction Methods for High-Rise Buildings with Active Mass Damper Control Systems

To improve the performance of an active mass damper control system,the controller should be designed based on a reduced-order model. An improved method based on balanced truncation method was proposed to reduce the dimension of high-rise buildings,and was compared with other widely used reduction methods by using a framework with ten floors. This optimized method has improvement of reduction process and choice of the order. Based on the reduced-order model obtained by the improved method and pole-assignment algorithm,a controller was designed. Finally,a comparative analysis of structural responses,transfer functions,and poles was conducted on an actual high-rise building. The results show the effectiveness of the improved method.

Speed Reduction Mitigation Strategies on Rural Highways at Two-Way Stop Control Intersections and Curves

Studies conducted on crashes at rural intersections of state highways and local roads/streets with two-way stop control have proved that the problem was likely poor judgment by the stopped driver on the minor approach of the speed of an oncoming vehicle and/or safe gap in traffic on the major highway. Several mitigating strategies have been suggested and studied in various studies to improve safety at the two-way stop control rural intersections and at other rural highway segments. There are also several low-cost techniques used, mostly in foreign countries, to slow drivers on major highways as they enter small towns and villages, e.g., narrowing pavement lines, establishing visual gateways, etc. Lowered speeds would decrease crash severity. In this study, four strategies including solar speed display units, mobile speed trailers, optical speed bars, and colored pavement were tested and assessed in some locations in Kansas. The results of this research indicate that both solar speed display units and mobile speed trailers are effective in speed reduction at the desired points, but optical speed bars and colored pavements do not yield reliable results. Additional studies and longer term studies, should be conducted.

Signal averaging for noise reduction in anesthesia monitoring and control with communication channels

This paper investigates impact of noise and signal averaging on patient control in anesthesia applications, especially in networked control system settings such as wireless connected systems, sensor networks, local area networks, or tele-medicine over a wide area network. Such systems involve communication channels which introduce noises due to quantization, channel noises, and have limited communication bandwidth resources. Usually signal averaging can be used effectively in reducing noise effects when remote monitoring and diagnosis are involved. However, when feedback is intended, we show that signal averaging will lose its utility substantially. To explain this phenomenon, we analyze stability margins under signal averaging and derive some optimal strategies for selecting window sizes. A typical case of anesthe-sia depth control problems is used in this development.

Research on the effects of command-and-control and market-oriented policy tools on China's energy conservation and emissions reduction innovation

The impact of environmental regulation on technology innovation is a hot spot in current research where a large number of empirical studies are based on Porter Hypothesis(PH). However, there are still controversies in academia about the establishment of "weak" and "narrow" versions of PH. Based on the panel data of application for patent of energy conservation and emission reduction(ECER) technology of Chinese city scale during 2008-2014, comprehensive energy price, pollutant emission, etc., mixed regression model and systematic generalized method of moments method were adopted, respectively,to study the impact of market-oriented and command-and-control policy tool on China's ECER technology innovation. The results show that the environmental regulation hindered the technological innovation in the immediate phase; however, it turned out to be positive in the first-lag phase. Hence, the establishment of "weak" PH is time-bounded. The command-and-control policy tool played a more positive role in promoting technological innovation in the first-lag phase than market-oriented policy tool. Therefore, "narrow" PH is not tenable. The reason is that the main participants of China's ECER technology innovation are state-owned companies and public institutions. Regionally speaking, the impact which command-and-control policy tool has on technological innovation at sight was nonsignificant in the eastern, the central, and the western regions of China whilst market-oriented policy tool had a negative effect. And market-oriented policy tool in the central region had strongest negative effect, which would diminish in the eastern region and become weakest in the western region. This was related to regional energy consumption level and the market economic vitality.

Effect Analysis of "One Prevention Double Reduction" of Aerial Control in Corn Fields in Daiyue District, Tai’an City

The main technical content of full mechanized corn production in Daiyue District is explained,and the problems of disease and insect pest control in the middle and late growth stage of corn in full mechanized production are analyzed."One prevention double reduction"of corn performed by unmanned aerial vehicle(UAV)and self-propelled sprayer is compared and analyzed,and some suggestions are put forward for further popularization and application of full mechanized corn production.

Exploration and Practice of Precision Emission Reduction Monitoring System in Air Pollution Prevention and Control in a District of Tianjin

At present,China’s atmospheric environmental protection work has achieved initial results,but environmental protection is facing increasing pressure,and the environmental situation is still not optimistic.In response to the call of the state,efforts have been intensified in environmental protection and ecological civilization construction,and supply-side structural reform has been actively promoted,and the Implementation Plan for Tianjin’s Comprehensive Discharge of Industrial Pollution Sources to Meet Standards has been promoted.When the total amount of pollutants discharged in key areas far exceeds the environmental capacity,regional heavy pollution weather will still occur once adverse meteorological conditions are encountered.In accordance with the Law of the People’s Republic of China on the Prevention and Control of Atmospheric Pollution,when the deterioration of air quality to a certain extent,to protect public health,key gas related industries should carry out emergency emission reduction in accordance with the local emergency plan while the local government starts the emergency response of heavy pollution weather.Direct economic loss of emergency response to heavy pollution weather is enormous.On the basis of meeting the total amount of emissions required by the state,the project aims to achieve the effect of"emission reduction and production increase"by precise emission reduction according to local characteristics.

Short term acupressure therapy on weight-reduction in adolescence: A randomized controlled trial

Aim: Common treatment options for obesity include a reduced-calorie diet, increased physical activity, behavioral modification, pharmacotherapy, and surgery. Ear acupressure may also be an effective adjunct therapy. Methods: This study used a randomized controlled design to test the effectiveness of auricular acupressure for weight reduction in young, Taiwan Residents adults with a BMI ≥ 23 kg/m2. Sixty-eight participants aged 18 to 20 years were recruited from Taiwan Residents universities at the beginning of the study. After four weeks of auricular therapy, the total sample included 57 young adults. All participants met one time per week for ten minutes. The treatment group received ear acupressure treatment with Semen Vaccariae sticks on auricular acupoints while the control group had adhesive tape placed on ear acupoints, change in BMI from baseline to trial completion. Results: BMI in controls increased significantly by +0.0133 kg/m2 (P = 0.000) while the intervention group BMI decreased significantly by ?0.8022 kg/m2 (P ≤ 0.0001). Conclusions: Just four weeks of auricular acupressure by Semen Vaccariae, sticks may significantly help to decrease BMI among young adults.

Unexpected/contrary behavior of aerosol mass concentration in response to the individual components'concentration reduction in Kitakyushu,Japan

In the suburbs of Kitakyushu,Japan,the inorganic aerosol mass concentration(IAM)was about 32.7μg/m^(3),with the aerosol pH of 3.3.To study the thermodynamics of aerosol when its individual components'concentration is reduced,sensitive tests were performed using the ISORROPIAⅡmodel,in which the seven control species—TNaCl,TNH_(4)^(+),TSO_(4)^(2-),TNO_(3)^(-),TMg^(2+),TK^(+),and TCa^(2+)—were taken into account.IAM and inorganic aerosol pH after reducing TNaCl,TNO_(3)^(-),TMg^(2+),TK^(+),and TCa^(2+)responded linearly(0%≤concentration reduction ratio(CRR)≤100%,with the exception of 100%in TNaCl);the nonlinear variations of these two parameters could be observed by controlling TNH_(4)^(+)and TSO_(4)^(2-).Unexpected aerosol behavior occurred at 100%reduction of TNaCl,which was caused by the sudden increase of NO_(3)^(-),NH_(4)^(+),and aerosol liquid water content(ALWC);the increase of IAM was also observed after controlling TSO_(4)^(2-)(60%≤CRR≤100%)and TCa^(2+)(0%≤CRR≤100%),which was mainly related to the variation of ALWC driven by the response of CaSO_(4).Multiple regression analysis showed that ALWC was statistically and strongly related to the variations of NO_(3)^(-),Cl-,SO_(4)^(2-),HSO_(4)^(-),HNO_(3),and NH_(3)(P<0.05),with regression coefficients of 1.68,5.23,1.83,2.81,0.34,and 0.57,respectively.The highest coefficient(5.23)was found for Cl^(-),revealing that sea salts significantly influenced particle responses.Overall,this study comprehensively investigated aerosol characteristics and inner responses for the reduction of components,which is of great significance for a better understanding of atmospheric chemistry in Kitakyushu,Japan.

Size Distributions of Aerosol Sulfates and Nitrates in Beijing during the 2008 Olympic Games： Impacts of Pollution Control Measures and Regional Transport

For the 2008 Olympic Games, drastic control measures were implemented on industrial and urban emissions of sulfur dioxide （SO2）, nitrogen oxides （NOx） and other pollutants to address the issues of poor air quality in Beijing. To investigate the effects of SO2 and NOx reductions on the particulate sulfate and nitrate concentrations as well as their size distributions, size-segregated aerosol samples were collected using micro-orifice uniform deposit impactors （MOUDIs） at urban and downwind rural sites in Beijing before and after full-scale controls. During the sampling period, the mass concentrations of fine particles （PMI.s） at the urban and rural sites were 94.0 and 85.9 p.g m-3, respectively. More than 90% of the sulfates and 60% of nitrates formed as fine particles. Benefiting from the advantageous meteorological conditions and the source controls, sulfates were observed in rather low concentrations and primarily in condensation mode during the Olympics. The effects of the control measures were separately analyzed for the northerly and the southerly air-mass-dominated days to account for any bias. After the control measures were implemented, PM, sulfates, and nitrates were significantly reduced when the northerly air masses prevailed, with a higher percentage of reduction in larger particles. The droplet mode particles, which dominated the sulfates and nitrates before the controls were implemented, were remarkably reduced in mass concentration after the control measures were implemented. Nevertheless, when the polluted southerly air masses prevailed, the local source control measures in Beijing did not effectively reduce the ambient sulfate concentration due to the enormous regional contribution from the North China Plain.