Nanobubbles produced by hydraulic air compression technique

The anoxia of coastal water has already been a serious problem all over the word.Nanobubbles are proved to have great applications in water remediation because they could effectively increase the oxygen content and degrade organic matters in water.But the existing methods to produce nanobubbles are complicated and high cost to operate,especially in deep sea.In this paper,we presented a low-cost method,hydraulic air compression(HAC),to produce a large number of nanobubbles and proved that nanoscale gas bubbles could be produced by HAC for the first time.Nanoparticle tracking analysis was used to measure the size and concentration of produced nanobubbles.It indicated that the concentration of nanobubbles would increase as the downpipe height increases.Degassed measurements proved that produced“nanoparticles”are gas nanobubbles indeed.More dissolved oxygen in water would provide the source for larger number of nanobubble formation.Those results are expected to be very helpful for water remediation in ocean in the future.

Lift on a Low Speed Circular Arc Wing due to Air Compression

A fluid flow model consisting of Bernoulli’s law in its normal form, the equation of state of air, and the cross-stream force balance between a downward pressure gradient and the upward centrifugal force on fluid particles moving along curved streamlines over the top circular wing surface involving three equations in three unknowns (pressure, density and velocity) are solved to show that both density and pressure decrease upward as the inverse square of the distance from the circle’s center, and the velocity is independent of that dis-tance. These derived characteristics are used to explain the lift force on the wing in what is believed to be a novel way.

Efficiency Analysis of an Arrayed Liquid Piston Isothermal Air Compression System for Compressed Air Energy Storage

Compressed air energy storage(CAES)is an important technology in the development of renewable energy.The main advantages of CAES are its high energy capacity and environmental friendliness.One of the main challenges is its low energy density,meaning a natural cavern is required for air storage.High-pressure air compression can effectively solve the problem.A liquid piston gas compressor facilitates high-pressure compression,and efficient convective heat transfer can significantly reduce the compression energy consumption during air compression.In this paper,a near isothermal compression method is proposed to increase the surface area and heat exchange by using multiple tube bundles in parallel in the compression chamber in order to obtain high-pressure air using liquid-driven compression.Air compression with a compression ratio of 6.25:1 is achieved by reducing the tube diameter and increasing the parallel tube number while keeping the compression chamber cross-sectional area constant in order to obtain a high-pressure air of 5 MPa.The performances of this system are analyzed when different numbers of tubes are applied.A system compression efficiency of 93.0%and an expansion efficiency of 92.9%can be achieved when 1000 tubes are applied at a 1 minute period.A new approach is provided in this study to achieve high efficiency and high pressure compressed air energy storage.

A novel nano-grade organosilicon polymer:Improving airtightness of compressed air energy storage in hard rock formations

Enhancing cavern sealing is crucial for improving the efficiency of compressed air energy storage(CAES)in hard rock formations.This study introduced a novel approach using a nano-grade organosilicon polymer(NOSP)as a sealant,coupled with an air seepage evaluation model that incorporates Knudsen diffusion.Moreover,the initial coating application methods were outlined,and the advantages of using NOSP compared to other sealing materials,particularly regarding cost and construction techniques,were also examined and discussed.Experimental results indicated a significant reduction in permeability of rock specimens coated with a 7–10μm thick NOSP layer.Specifically,under a 0.5 MPa pulse pressure,the permeability decreased to less than 1 n D,and under a 4 MPa pulse pressure,it ranged between4.5×10^(-6)–5.5×10^(-6)m D,marking a 75%–80%decrease in granite permeability.The sealing efficacy of NOSP surpasses concrete and is comparable to rubber materials.The optimal viscosity for application lies between 95 and 105 KU,and the coating thickness should ideally range from 7 to 10μm,applied to substrates with less than 3%porosity.This study provides new insights into air transport and sealing mechanisms at the pore level,proposing NOSP as a cost-effective and simplified solution for CAES applications.

Air tightness of compressed air storage energy caverns with polymer sealing layer subjected to various air pressures

During the operation of compressed air storage energy system,the rapid change of air pressure in a cavern will cause drastic changes in air density and permeability coefficient of sealing layer.To calculate and properly evaluate air tightness of polymer sealing caverns,the air-pressure-related air density and permeability must be considered.In this context,the high-pressure air penetration in the polymer sealing layer is studied in consideration of thermodynamic change of the cavern structure during the system operation.The air tightness model of compressed air storage energy caverns is then established.In the model,the permeability coefficient and air density of sealing layer vary with air pressure,and the effectiveness of the model is verified by field data in two test caverns.Finally,a compressed air storage energy cavern is taken as an example to understand the air tightness.The air leakage rate in the caverns is larger than that using air-pressure-independent permeability coefficient and air density,which is constant and small in the previous leakage rate calculation.Under the operating pressure of 4.5-10 MPa,the daily air leakage in the compressed air storage energy cavern of Yungang Mine with high polymer butyl rubber as the sealing material is 0.62%,which can meet the sealing requirements of compressed air storage energy caverns.The air tightness of the polymer sealing cavern is mainly affected by the cavern operating pressure,injected air temperature,cavern radius,and sealing layer thickness.The cavern air leakage rate will be decreased to reduce the cavern operating pressure the injection air temperature,or the cavern radius and sealing layer thickness will be increased.

Design and Development of Wind-Solar Hybrid Power System with Compressed Air Energy Storage for Voltage and Frequency Regulations

The intermittent nature of wind and solar photovoltaic energy systems leads to the fluctuation of power generated due to the fact that the power output is highly dependent upon local weather conditions, which results to the load shading issue that led to the voltage and frequency instability. In additional to that, the high proportions of erratic renewable energy sources can lead to erratic frequency changes which affect the grid stability. In order to reduce this effect, the energy storage system is commonly used in most wind-solar energy systems to balance the voltage and frequency instability during load variations. One of the innovative energy storage systems is the compressed air energy storage system (CAES) for wind and solar hybrid energy system and this technology is the key focus in this research study. The aim of this research was to examine the system configuration of the CAES system through modelling and experimental approach with PID controller design for regulating the voltage and frequency under different load conditions. The essential elements and the entire system have been presented in this work as thorough modelling in the MATLAB/Simulink environment for different load conditions. The developed model was tested through an experimental workbench using the developed prototype of the compressed air storage in the Siemens Lab at DeKUT and explored the consequence of the working parameters on the system proficiency and the model accuracy. The performance of the system for the developed prototype of CAES system was validated using results from an experimental workbench with MATLAB/Simulink R2022b simulation. The modeling and experimental results, shows that the frequency fluctuation and voltage drop of the developed CAES system during load variations was governed by the I/P converter using a PID_Compact controller programed in the TIA Portal V17 software and downloaded into PLC S7 1200. Based on these results, the model can be applied as a basis for the performance assessment of the compressed air energy storage system so as to be included in current technology of wind and solar hybrid energy systems.

Analytical and Experimental Study on Complex Compressed Air Pipe Network

To analyze the working characteristics of complex compressed air networks, numerical methods are widely used which are based on finite element technology or intelligent algorithms. However, the effectiveness of the numerical methods is limited. In this paper, to provide a new method to optimize the design and the air supply strategy of the complex compressed air pipe network, firstly, a novel method to analyze the topology structure of the compressed air flow in the pipe network is initially proposed. A matrix is used to describe the topology structure of the compressed air flow. Moreover, based on the analysis of the pressure loss of the pipe network, the relationship between the pressure and the flow of the compressed air is derived, and a prediction method of pressure fluctuation and air flow in a segment in a complex pipe network is proposed. Finally, to inspect the effectiveness of the method, an experiment with a complex network is designed. The pressure and the flow of airflow in the network are measured and studied. The results of the study show that, the predicted results with the proposed method have a good consistency with the experimental results, and that verifies the air flow prediction method of the complex pipe network. This research proposes a new method to analyze the compressed air network and a prediction method of pressure fluctuation and air flow in a segment, which can predicate the fluctuation of the pressure according to the flow of compressed air, and predicate the fluctuation of the flow according to the pressure in a segment of a complex pipe network.

Design issues for compressed air energy storage in sealed underground cavities

Compressed air energy storage （CAES） systems represent a new technology for storing very large amount of energy. A peculiarity of the systems is that gas must be stored under a high pressure （p - 10-30 MPa）. A lined rock cavern （LRC） in the form of a tunnel or shaft can be used within this pressure range. The rock mass surrounding the opening resists the internal pressure and the lining ensures gas tightness. The present paper investigates the key aspects of technical feasibility of shallow LRC tunnels or shafts under a wide range of geotechnical conditions. Results show that the safety with respect to uplift failure of the rock mass is a necessary but not a sufficient condition for assessing feasibility. The deformation of the rock mass should also be kept sufficiently small to preserve the integrity of the lining and, especially, its tightness. If the rock is not sufficiently stiff, buckling or fatigue failure of the steel lining becomes more decisive when evaluating the feasible operating air pressure. The design of the concrete plug that seals the compressed air stored in the container is another demanding task. Numerical analyses indicate that in most cases, the stability of the rock mass under the plug loading is not a decisive factor for plug design.

Performance Analysis of Constant-Pressure Pumped Hydro Combined with Compressed Air Energy Storage System Considering Off-Design Model of Compressor

With the wide application of renewable energy, energy storage technology has become a research hotspot. In order to overcome the shortcomings of energy loss caused by compression heating in compressed air energy storage technology, a novel constant-pressure pumped hydro combined with compressed air energy storage system was proposed. To deepen the understanding of the system and make the analysis closer to reality, this paper adopted an off-design model of the compressor to calculate and analyze the effect of key parameters on system thermodynamics performance. In addition, the results of this paper were compared with previous research results, and it was found that the current efficiency considering the off-design model of compressor was generally 2% - 5% higher than the previous efficiency. With increased preset pressure or with decreased terminal pressure, both the previous efficiency and current efficiency of the system increased. The exergy destruction coefficient of the throttle valve reached 4%. System efficiency was more sensitive to changes in water pump efficiency and hydroturbine efficiency.

Optimization Study on a Single-cylinder Compressed Air Engine

The current research of compressed air engine（CAE） mainly focused on simulations and system integrations. However, energy efficiency and output torque of the CAE is limited, which restricts its application and popularization. In this paper, the working principles of CAE are briefly introduced. To set a foundation for the study on the optimization of the CAE, the basic mathematical model of working processes is set up. A pressure-compensated valve which can reduce the inertia force of the valve is proposed. To verify the mathematical model, the prototype with the newly designed pressure-compensated intake valve is built and the experiment is carried out, simulation and experimental results of the CAE are conducted, and pressures inside the cylinder and output torque of the CAE are obtained. Orthogonal design and grey relation analysis are utilized to optimize structural parameters. The experimental and optimized results show that, first of all, pressure inside the cylinder has the same changing tendency in both simulation curve and experimental curve. Secondly, the highest average output torque is obtained at the highest intake pressure and the lowest rotate speed. Thirdly, the optimization of the single-cylinder CAE can improve the working efficiency from an original 21.95% to 50.1%, an overall increase of 28.15%, and the average output torque increases also increases from 22.047 5 N · m to 22.439 N · m. This research designs a single-cylinder CAE with pressure-compensated intake valve, and proposes a structural parameters design method which improves the single-cylinder CAE performance.

Performance Evaluation of Compressed Air Energy Storage Using TRNSYS

The appreciable economic growth in some of the developing countries like India in the recent years, towards providing energy security causes large environmental impact. Renewable Energy （RE） is being seen as one of the important means to meet the growing power needs of the economy while enhancing energy security and providing opportunities for mitigating greenhouse gas emissions. However, RE sources are highly intermittent in nature. The variability of these sources has led to concerns regarding the reliability of an electric grid that derives a large fraction of its energy from these sources as well as the cost of reliably integrating large amounts of variable generation into the electric grid. Hence at this juncture, it is necessary to explore the benefits of suitable Energy storage technologies. Compressed air energy storage （CAES） is a commercial, utility-scale technology that provides long-duration energy storage with fast ramp rates and good part-load operation. It is a promising storage technology for balancing the large-scale penetration of renewable energies, such as wind and solar power, into electric grids. Considering the potential of CAES storage, the present work, a thermodynamic model is developed with suitable assumptions and the simulation analysis is performed using transient system simulation （TRNSYS） v17 software. The system performanee is compared by considering the recovery during the heat of compression using a thermal storage system and without considering the heat recovery. The overall turnaround efficiency of the system without considering the thermal energy storage （TES） system is 57 % and with TES system the efficiency is increased to 70%.

Rectosigmoid perforation after high-pressure air jet exposure: A case report

Rationale:Colonic barotrauma induced by high-pressure air compressors has been reported more frequently these days due to the widespread use of air compressors in industries.Such enormous pressure into the rectum can lead to devastating injuries.Patient's concern:A 35-year-old male was referred to our emergency department with an alleged history of directing high pressure compressed air jet towards the anus.There was diffuse subcutaneous emphysema over the neck,chest,abdomen,and extremities,and he presented with hemodynamic instability and respiratory failure.Diagnosis:Rectosigmoid perforation due to exposure to high-pressure air jet causing tension pneumoperitoneum,pneumomediastinum,pneumothorax,and extensive subcutaneous emphysema.Intervention:In view of tension pneumoperitoneum,urgent percutaneous needle decompression was performed using 16 G needle,5 cm superomedial to the anterior superior iliac spine.The gush of air was released along with reduction in abdominal distension and improvement in hemodynamics.Outcome:The patient succumbed two days later due to septic shock.Lessons:This case highlighted the importance of promoting education about work safety among industrial workers especially in developing countries like India.

Forced Compressed Air Cooling System for a 300 MW Steam Turbine in Waigaoqiao Power Plant

The 300 MW steam turbine installed in Waigaoqiao Power Plant with combined HPIP cylinders of double casing structure is a product of the Shanghai Turbine Works utilizing licensed technology. It has a large heat storage capacity and good thermal insulation, so the metal temperature of first stage of HP cylinder (FSMTI) may reach 400-450℃ after shut down and it takes 7-8 days to cool to 150℃ by natural cooling, Now with a forced cooling system the cooling time may be reduced to 40 hours, so that the turbine may be opened for repair work in about 5-6 days. The cooling system for #2 unit and test procedure are briefly described below.

A Numerical Study on the Water Impact of the Rigid/Elastic Box-Like Structure

Recent damages to the box-like structures caused by wave slamming have made it necessary to study the impact problems of this kind of structure. This paper showed findings from numerical simulations of the rigid/elastic structures, aiming to gain insights into the characteristics of the problem. The results of the rigid cases showed the significance of air compressibility during the impact process, while the slamming phenomena became quite different without the effect. In the elastic cases, the trapped air made the structure vibrate at frequencies much smaller than its eigenfrequencies. Besides, the structural deformation made it easy for the trapped air to escape outwards, which weakened the air cushioning effect, especially at high impact velocities. The above analysis gives the results when the structural symmetry axis was vertical to the water(vertical impacts). In addition, the results were given when the axis was oblique to the water(oblique impacts). Compared with the vertical cases, the impact phenomena and structural response showed asymmetry. This work used the computational fluid dynamics(CFD) method to describe fluid motion and the finite element method(FEM) for the deformable structure. A two-way coupling approach was used to deal with the fluid-structure interaction in the elastic cases.

Design Strategy of Diagonal Compressors in Compressed Air Energy Storage System

As a kind of large-scale physical energy storage,compressed air energy storage(CAES)plays an important role in the construction of more efficient energy system based on renewable energy in the future.Compared with traditional industrial compressors,the compressor of CAES has higher off-design performance requirements.From the perspective of design,it needs to pay attention not only to the performance of the design point,but also to the performance of all the stable working range.However,from the previous literature,no diagonal compressor was used in CAES which can meet the requirements,which also reflects the design program can be further improved.Therefore,this paper studies the design strategy of high efficient diagonal compressor for large-scale CAES,and gives the complete strategy algorithms used for different program modules.The pressure ratio,isentropic efficiency and stable working range are comprehensively considered.In the design process,the criteria for the key parameters of the diagonal flow angle of the diagonal compressor are given for the first time.The results show that the isentropic efficiency at the design point is 92.7%,the total pressure ratio is1.97,and the stable working range exceeds 20%,which meets the design requirements of the compressor for CAES and exceeds the overall performance of the previous compressors in the entire working range.

Comparative analysis of thermodynamic and mechanical responses between underground hydrogen storage and compressed air energy storage in lined rock caverns

Underground hydrogen storage(UHS)and compressed air energy storage(CAES)are two viable largescale energy storage technologies for mitigating the intermittency of wind and solar power.Therefore,it is meaningful to compare the properties of hydrogen and air with typical thermodynamic storage processes.This study employs a multi-physical coupling model to compare the operations of CAES and UHS,integrating gas thermodynamics within caverns,thermal conduction,and mechanical deformation around rock caverns.Gas thermodynamic responses are validated using additional simulations and the field test data.Temperature and pressure variations of air and hydrogen within rock caverns exhibit similarities under both adiabatic and diabatic simulation modes.Hydrogen reaches higher temperature and pressure following gas charging stage compared to air,and the ideal gas assumption may lead to overestimation of gas temperature and pressure.Unlike steel lining of CAES,the sealing layer(fibre-reinforced plastic FRP)in UHS is prone to deformation but can effectively mitigates stress in the sealing layer.In CAES,the first principal stress on the surface of the sealing layer and concrete lining is tensile stress,whereas UHS exhibits compressive stress in the same areas.Our present research can provide references for the selection of energy storage methods.

疏松砂岩超声测试及其结果分析

在室温常压下，通过对大量疏松砂岩的超声测定发现：①其纵、横波速度较低；②纵波速度vp在饱和水时比在饱和空气时有较大的增加；③横渡速度vs在饱和水时比在饱和空气时略有降低；④纵、横波速度比vp／vs在饱和水时比在饱和空气时有较大的增加；⑤纵、横波速度与孔隙率呈线性关系。

Feasibility evaluation for excavation of Naghshe Jahan Square subway station by underground methods

In recent years, in reaction to the increasing usage of urban areas, the excavation of underground spaces has been developed. One of the most challenging issues encountered by engineers is the construction of subway stations as large underground spaces at shallow depth with soft surrounding soils. In this paper, Naghshe Jahan Square subway station located in Isfahan, Iran, has been simulated by geomechanical fnite difference method(FDM). This station is located under important historical structures. Therefore, the ground displacement and surface settlement induced by the excavation of the subway station should be strictly controlled. Many of such problems are affected by selected excavation method. For these reasons, different underground excavation methods associated with construction have been studied. In this study, sequential excavation method and large-diameter curved pipe roofng method are used and the numerical results of the two methods are compared. The presence of groundwater table obliges us to choose special techniques for the stability of the ground around the subway station during construction; hence compressed air and ground freezing techniques are utilized in the simulations of the subway station. Finally, after choosing appropriate support systems, the large-diameter curved pipe roofng method with 1.5 m spacing between curved pipes is proposed.

超声波透射法测试水泥基材料凝结时间研究综述

水泥基材料加水搅拌后,随着水化反应的进行,其状态从可塑性流体逐渐转变为具有一定强度的硬化固体,此过程可采用超声波透射法进行连续、无损监测。通过分析获得的超声波信号如波速、振幅等,可解读出反映水泥基材料的水化进程信息。本文从试验装置、测试原理、主要影响因素及凝结时间判断方法等四个方面介绍了超声波透射法在测定水泥基材料凝结时间上的研究进展,讨论了浆体含气量对超声波波速的影响,并分析了现有凝结时间判断方法的优缺点。

Increasing Coal-Fired Power Plant Operational Flexibility by Integrating Solar Thermal Energy and Compressed Air Energy Storage System

This paper proposed a novel integrated system with solar energy,thermal energy storage(TES),coal-fired power plant(CFPP),and compressed air energy storage(CAES)system to improve the operational flexibility of the CFPP.A portion of the solar energy is adopted for preheating the boiler’s feedwater,and another portion is stored in the TES for the CAES discharging process.Condensate water from the CFPP condenser is used for cooling compressed air during the CAES charging process.The thermodynamic performance of the integrated system under different load conditions is studied.The system operations in a typical day are simulated with EBSILON software.The system enables daily coal saving of 9.88 t and reduces CO_(2)emission by 27.95 t compared with the original CFPP at 100%load.Under partial load conditions,the system enables maximum coal saving of 10.29 t and maximum CO_(2)emission reduction of 29.11 t at 75%load.The system has maximum peak shaving depth of 9.42%under 40%load condition.The potential of the system participating ancillary service is also discussed.It is found that the integration of solar thermal system and CAES system can bring significant ancillary service revenue to a conventional CFPP.