Draft sensation distribution of air jet supply system in large space building in summer

To study the draft sensation distribution of an air jet supply system in a large space building in summer,experiments are conducted in a large laboratory.The temperature,velocity and draft sensation distributions at a nozzle height of 4 m in the occupied zone are obtained.Then,the numerical simulation under the test condition is carried out by the computational fluid dynamics（CFD）method.The calculation results of the indoor vertical temperature and the draft sensation distribution are validated by the test data.Simulations with different nozzle heights are conducted.The satisfactory air supply condition is determined by analyzing the draft sensations and the temperatures in the occupied zone under three conditions.The simulation results show that the optimal draft sensation distribution and the uniform temperature and velocity fields can be obtained at a nozzle height of 5 m.

Influence of abrasive hardness on erosion wear of abrasive air jets

To make clear the influence of abrasive hardness on the erosion effect,the erosion experiments of abrasive air jet with the same impact energy were carried out.The influence of abrasive hardness on the erosion effect is clarified by comparing the different erosion depths.The main conclusions are as follows.Under the same mass flow rate and mesh number,the abrasive with a higher density needs greater pressure irrespective of hardness.After erosion damage,the abrasive size exhibits a Weibull distribution.The shape parameterβand Weibull distribution function of four types of abrasives are derived by the least squares method;moreover,βis found to have a quadratic relation with abrasive hardness.The results of the erosion experiments show that abrasive hardness and erosion depth are quadratically related.By calculating the increase in surface energy after abrasive erosion crushing,it is found that abrasive hardness has a quadratic relation with surface energy and that the increases in erosion depth and surface energy consumption are basically identical.In conclusion,the effect is a soft abrasive impact when the ratio of abrasive hardness(Ha)to the material hardness(Hm)is<2.6,and it is a hard abrasive impact when Ha/Hm>3.

Effects of cryogenic cold air jet cutting on chip break in metal machining

The half-dry cutting employs cryogenic compressed air cooled down to (10 to 40) and a micro-dosage of lubricating oil, called cryogenic cold air jet cutting was studied. On the basis of a comparative experiment on dry and cryogenic cold air jet cuttings carried out for grade 45 steel, the effects of cryogenic cold air jet on the breaking of chips were discussed. The experimental results reveal that in the valid ranges of pressure and temperature, the cryogenic cold air jet widens the chip breaking areas effectively. When the cutting depth is not greater than 1 mm, the influence of chip breaking is much more significant. But different injecting angle of cold air has different influence on the chip-break. From the experiment, the optimized jet injecting angle, temperature effecting range and pressure working range of cold air are obtained. These results can offer a foundation for industrial manufacturing.

Increasing the Energy Efficiency of Air Jet Weaving Based on a Novel Method to Exploit Energy Savings Potentials in Production Processes of the Textile Industry

This article deals with the energy efficiency of textile weaving machines. A method based on exergy balances has been developed at the Institute for Textile Technology RWTH Aachen University （ITA）, Aachen, Germany in order to improve energy efficiency textile machines. The relay nozzles of the air-jet weaving technology need up to 80% of the energy of the weaving machine. At ITA, a new nozzle concept was developed. The developed geometry is a so called High-Volume-Low-Pressure nozzle （HVLP nozzle）, based on convergent nozzle aerodynamic theory. With this concept, energy savings up to 30% are possible.

Acoustic Absorption Characteristics of Perforated Thin Plate with Air Jets and Cavity

The present paper focuses on the effect of air jets through a perforated thin plate on the characteristics of an acoustic absorption coefficient. We measured the flow rate, internal pressure, acoustic pressure, and transfer function by using an improved acoustic impedance tube. The normal incidence absorption coefficient was calculated from the measured transfer function using transfer function methods. As a result, the frequency characteristics of the acoustic absorption coefficient against the frequency showed a maximum value at the local frequency. The peak frequency of the acoustic absorption coefficient depended on the thickness of the background air space and the thickness of the perforated plate. As the flow rate increased through the micropores, the peak level of the acoustic absorption coefficient also increased until a flow rate of 80?l /min. As the flow rate further increased, the peak level of the acoustic absorption coefficient decreased and that of the high frequency band increased.

On the Method of Air Jet Cooling in Green Manufacturing

Green cooling is an important technology in green manufacturing. In the way of jetting, cooling airflo-w in used in the experiments of metal material cutting, by comparison of the changes of some technological factors, such as cutting heat, surface finish, in the process of jet cooling, pour cooling and natural cooling, we can draiv the conclusion that air jet cooling has a better cooling effect and green function. It can be 'widely used in both traditional and automatic green manufacturing.

A Study of the Gas Flow through Air Jet Loom

Air jet loom, as one of the shuttleless looms, transports a yam into warps using viscosity and kinetic energy of an air jet. Performance of this picking system depends on the ability of instantaneous inhalation/exhaust, configuration of nozzle, operation characteristics of a check valve, etc. In the recent past, many studies have been reported on the air jet discharged from a nozzle exit, but studies for understanding the flow field characteristics associated with shear layer and shock wave/boundary layer interaction in the nozzle were not conducted enough. In this paper, a computational study was performed to explain the flow field in the air jet nozzle with an acceleration tube and validated with previous experimental data available. The results obtained from the computational study show that, in the supersonic flow regime, the flow field depends significantly on the length of acceleration tube. As nozzle pressure ratio increases, drag force acting on the string also increases. For a longer acceleration tube, the total pressure loss is large, owing to the frictional loss.

Prediction of Acoustic Absorption Performance of a Perforated Plate with Air Jets

The present study focuses on the prediction of acoustic absorption performance of a perforated plate with air jets by theoretical calculations. In addition, we experimentally measured the flow rate, internal pressure, acoustic pressure, and transfer function using an acoustic impedance tube. The normal incidence absorption coefficient was calculated from the measured transfer function using transfer function methods. We investigated the influences of background air space, flow velocity, thickness, aperture rate, and aperture diameter of a perforated plate on the acoustic absorption characteristics. The frequency characteristics of the acoustic absorption coefficient showed a maximum value at a local frequency. As the background air space increased, the peak frequency of acoustic absorption characteristics decreased. As the flow velocity passing through the apertures increased, the peak level of the acoustic absorption coefficient also increased. The theoretical results agreed well with the experimental ones qualitatively.

On numerical investigation of nonuniformity in cooling characteristic for different materials of target surfaces being exposed to impingement of air jet

Heat transfer using air jet impingement technique is one of the conspicuous tasks in the looming world of electronic packaging system.Here,the material selection of heat sink becomes one of the prior and important assignments to construct a heat sink with desired characteristic cooling rate.In order to study the material effect of heat sink over the cooling characteristic,the present work takes an initiative in plotting the Nusselt magnitude over the radial distance for different material of heat sink.This is done by computing the flow regime and heat transfer characteristic of a 2D axis symmetric geometry in commercial simulating software,ANSYS CFX.The computation of cooling characteristic in form of Nusselt profile is done using SST+Gamma–theta turbulence model.Since the prediction of heat interaction due to the intermediacy and transition in the flow regime is a unique issue of this problem.The results for Nusselt curve signifies a tangible elevation in local Nusselt value(nonuniformity)with decrease in thermal diffusivity of target surface.Also the nonuniformity is observed to vanish above a critical range(66.76mm2/s)of thermal diffusivity.This happens due to presences of abnormal turbulence of heat flow which occurs inside the target surface.Since the variation in thermal diffusivity causes some imbalance competition between the heat storage and dissipation capabilities.Above all the target surface carrying thermal diffusivity less than 66.76mm2/s possesses a dominating heat storage capability,on behalf of which some heat transfer occurring in near jet and far jet regions are being restricted.These are transferred towards stagnation region in radial direction.

A novel approach of jet polishing for interior surface of small-grooved components using three developed setups

It is a challenge to polish the interior surface of an additively manufactured component with complex structures and groove sizes less than 1 mm.Traditional polishing methods are disabled to polish the component,meanwhile keeping the structure intact.To overcome this challenge,small-grooved components made of aluminum alloy with sizes less than 1 mm were fabricated by a custom-made printer.A novel approach to multi-phase jet(MPJ)polishing is proposed,utilizing a self-developed polisher that incorporates solid,liquid,and gas phases.In contrast,abrasive air jet(AAJ)polishing is recommended,employing a customized polisher that combines solid and gas phases.After jet polishing,surface roughness(Sa)on the interior surface of grooves decreases from pristine 8.596μm to 0.701μm and 0.336μm via AAJ polishing and MPJ polishing,respectively,and Sa reduces 92%and 96%,correspondingly.Furthermore,a formula defining the relationship between linear energy density and unit defect volume has been developed.The optimized parameters in additive manufacturing are that linear energy density varies from 0.135 J mm^(-1)to 0.22 J mm^(-1).The unit area defect volume achieved via the optimized parameters decreases to 1/12 of that achieved via non-optimized ones.Computational fluid dynamics simulation results reveal that material is removed by shear stress,and the alumina abrasives experience multiple collisions with the defects on the heat pipe groove,resulting in uniform material removal.This is in good agreement with the experimental results.The novel proposed setups,approach,and findings provide new insights into manufacturing complex-structured components,polishing the small-grooved structure,and keeping it unbroken.

Water-Air Mixing Jet Produced by Electro-hydraulic Impulse Technology Strengthening the Quality of Surface of Metal Materials

Electro-hydraulic impulse water-air mixing jet by which the quality of metal materials can be improved is described in this paper. The experimental results proved that the hardness and the micro-hardness of the surface layer of metal materials can be improved with this method, for example, the microhardness of CrWMn can be increased by 35.62 percent.

Study of generation characteristics of glow-type atmospheric-pressure plasma jet based on DC discharge in air

In order to form an atmospheric-pressure plasma jet without airflow, a needle–ring electrode structure is proposed in this paper. When heteropolar potentials are applied to a needle and a ring, a marked electric field strength enhancement around the needle’s pointed end has been found. When the same potential is applied to both the needle and the ring, the lateral electric field strength for the needle can be weakened. By using the above two methods, an increase of the difference between the pointed end electric field strength and the lateral one is achieved and stable plasma jets are formed. A symmetrical space electric field distribution is established at the pointed end of the needles when several sets of heteropolar needle–ring electrodes are uniformly arranged, which is conducive to forming a uniform array plasma jet. Under DC discharge conditions, a safe and stable plasma jet of high density and an array plasma jet are successfully achieved.

STUDY OF PET AIR-JET TEXTURING SEWING THREAD PROPERTIES

This paper presents a study of properties of air-jet textured threads made from high strengthpolyester filament and ordinary strength polyester filament.It includes the evaluation of tenacity,breaking elongation,modulus,specific work,evenness,abrasion resistance,hook strength,knotstrength and other mechanical properties relating to sewing.The polyester air-jet texturing sewingthread has special structure and appearance and possesses better properties of evenness,goodabrasion resistance,fatigue property,high hook and knot strength.

Design and Numerical Simulation of Low-Fiber Hollow Spindle in Air-Jet Vortex Spinning

Based on the mechanical system of free-end fibers and the analysis of pulling free-end fibers out of the spun yarn during spinning,a low-fiber hollow spindle is designed and the air distribution of fluent field is simulated numerically. The negative pressure effect is much bigger at the top of low-fiber hollow spindle than that in Murata No.861,which is more conducive for single fiber to get into the channel of hollow spindle. The tangential velocity in 0-3 mm at the top of hollow spindle increases and the fluctuation of radial velocity is much stronger,which enhance the wrapping effect. In the addition,the distribution of axial velocity remains the same.

Influence of air pressure on the performance of plasma synthetic jet actuator

Plasma synthetic jet actuator（PSJA） has a wide application prospect in the high-speed flow control field for its high jet velocity.In this paper,the influence of the air pressure on the performance of a two-electrode PSJA is investigated by the schlieren method in a large range from 7 k Pa to 100 k Pa.The energy consumed by the PSJA is roughly the same for all the pressure levels.Traces of the precursor shock wave velocity and the jet front velocity vary a lot for different pressures.The precursor shock wave velocity first decreases gradually and then remains at 345 m/s as the air pressure increases.The peak jet front velocity always appears at the first appearance of a jet,and it decreases gradually with the increase of the air pressure.A maximum precursor shock wave velocity of 520 m/s and a maximum jet front velocity of 440 m/s are observed at the pressure of 7 k Pa.The averaged jet velocity in one period ranges from 44 m/s to 54 m/s for all air pressures,and it drops with the rising of the air pressure.High velocities of the precursor shock wave and the jet front indicate that this type of PSJA can still be used to influence the high-speed flow field at 7 k Pa.

STUDY OF STRUCTURE AND RIGIDITY OF AIR-JET TEXTURED YARN(ATY)

This paper deals with the structure of air-jet textured yarn(ATY),especilly its core structurein dedail.It is described that overfeed of supply yarn does influence the ATY structure.Then thebending rigidity of ATY has been measured and analyzed.The results shows that various supplyyarns affect the core structure and bending rigidity of ATY.

Influence of water content on the inactivation of P. digitatum spores using an air–water plasma jet

In order to investigate whether an air–water plasma jet is beneficial to improve the efficiency of inactivation, a series of experiments were done using a ring-needle plasma jet. The water content in the working gas（air） was accurately measured based on the Karl Fischer method. The effects of water on the production of OH（A;Σ;–X;Π;） and O（3p;P–3s;S） were also studied by optical emission spectroscopy. The results show that the water content is in the range of 2.53–9.58 mg l;, depending on the gas/water mixture ratio. The production of OH（A;Σ;–X;Π;） rises with the increase of water content, whereas the O（3p;P–3s;S） shows a declining tendency with higher water content. The sterilization experiments indicate that this air–water plasma jet inactivates the P. digitatum spores very effectively and its efficiency rises with the increase of the water content. It is possible that OH（A;Σ;–X;Π;） is a more effective species in inactivation than O（3p;P–3s;S） and the water content benefit the spore germination inhibition through rising the OH（A;Σ;–X;Π;） production. The maximum of the inactivation efficacy is up to 93% when the applied voltage is -6.75 kV and the water content is 9.58 mg l;.

Prediction Analysis on the Transport Distance of Supply Air in Warm Air Heating Room with Impinging Jet Ventilation Systems

To overcome the disadvantages of displacement ventilation( DV) and traditional mixing ventilation( MV) system,a new ventilation system known as impinging jet ventilation system( IJVS)has been developing. The warm air can be supplied with impinging jet ventilation( IJV), while the DV is only used for cooling.However,the flow and temperature field of IJV under heating scenario has had few references. The paper is mainly focused on computational fluid dynamics( CFD) and developing an adequate correlation between the distance L that warm air can reach and different parameters in the warm IJVS by using response surface methodology( RSM). The results indicate that L decreases as the supply velocity υ decreases but increases as the supply temperature difference ΔT or the discharge height h decreases. In the variable air volume( VAV) system, it is necessary to determine supply parameters both under the maximum-heat-load condition and the small-heat-load condition. Unlike the VAV system,the constant air volume( CAV) system has no need to study the small-heat-load condition. Draught discomfort near the nozzle becomes the issue of concern in IJVS, thus the suitable discharge height is of great importance in design and can be calculated based on the predictive model.

Air China Signs Deal to Buy 23 Airbus Passenger Jets

Air China has signed a deal to buy 23 Airbus A320 passenger planes.

Study on Design of Pressure Chamber in a Linear-Jet Type Air Curtain System for Prevention of Smoke Spread

Death toll by smoke in fire is estimated at 70% which emphasizes the importance of smoke control system to deal with the fire smoke. In advanced countries, the studies on method to prevent smoke spread by forming the air curtain using high velocity jet flow are underway now. In this study, a linear-jet type air curtain system is proposed to prevent the smoke spread and analysis of flow characteristics of pressure chamber, which is the core component, is conducted through numerical analysis and experimental approach. Consequently, the pressure was increased in 2D functional way to input air flowrate and about 595 Pa pressure was formed at pressure chamber inlet in response to 30 m/s nozzle jet velocity.